static void i2c_init(void)
{
const struct i2c_port_t *p = i2c_ports;
int i;
for (i = 0; i < i2c_ports_used; i++, p++)
i2c_init_port(p);
#ifdef CONFIG_HOSTCMD_I2C_SLAVE_ADDR
STM32_I2C_CR1(I2C_PORT_EC) |= STM32_I2C_CR1_RXIE | STM32_I2C_CR1_ERRIE
| STM32_I2C_CR1_ADDRIE | STM32_I2C_CR1_STOPIE
| STM32_I2C_CR1_NACKIE;
#if defined(CONFIG_LOW_POWER_IDLE) && (I2C_PORT_EC == STM32_I2C1_PORT)
/*
* If using low power idle and EC port is I2C1, then set I2C1 to wake
* from STOP mode on address match. Note, this only works on I2C1 and
* only if the clock to I2C1 is HSI 8MHz.
*/
STM32_I2C_CR1(I2C_PORT_EC) |= STM32_I2C_CR1_WUPEN;
#endif
STM32_I2C_OAR1(I2C_PORT_EC) = 0x8000 | CONFIG_HOSTCMD_I2C_SLAVE_ADDR;
#ifdef TCPCI_I2C_SLAVE
/*
* Configure TCPC address with OA2[1] masked so that we respond
* to CONFIG_TCPC_I2C_BASE_ADDR and CONFIG_TCPC_I2C_BASE_ADDR + 2.
*/
STM32_I2C_OAR2(I2C_PORT_EC) = 0x8100 | CONFIG_TCPC_I2C_BASE_ADDR;
#endif
task_enable_irq(IRQ_SLAVE);
#endif
}
static void i2c_init_port(unsigned int port)
{
const int i2c_clock_bit[] = {21, 22};
if (!(STM32_RCC_APB1ENR & (1 << i2c_clock_bit[port]))) {
/* Only unwedge the bus if the clock is off */
if (i2c_claim(port) == EC_SUCCESS) {
i2c_release(port);
}
/* enable I2C2 clock */
STM32_RCC_APB1ENR |= 1 << i2c_clock_bit[port];
}
/* force reset of the i2c peripheral */
STM32_I2C_CR1(port) = 0x8000;
STM32_I2C_CR1(port) = 0x0000;
/* set clock configuration : standard mode (100kHz) */
STM32_I2C_CCR(port) = I2C_CCR;
/* set slave address */
if (port == I2C2)
STM32_I2C_OAR1(port) = I2C_ADDRESS;
/* configuration : I2C mode / Periphal enabled, ACK enabled */
STM32_I2C_CR1(port) = (1 << 10) | (1 << 0);
/* error and event interrupts enabled / input clock is 16Mhz */
STM32_I2C_CR2(port) = (1 << 9) | (1 << 8) | 0x10;
/* clear status */
STM32_I2C_SR1(port) = 0;
board_i2c_post_init(port);
}
static inline void dump_i2c_reg(int port)
{
#ifdef CONFIG_I2C_DEBUG
CPRINTF("CR1 : %016b\n", STM32_I2C_CR1(port));
CPRINTF("CR2 : %016b\n", STM32_I2C_CR2(port));
CPRINTF("SR2 : %016b\n", STM32_I2C_SR2(port));
CPRINTF("SR1 : %016b\n", STM32_I2C_SR1(port));
CPRINTF("OAR1 : %016b\n", STM32_I2C_OAR1(port));
CPRINTF("OAR2 : %016b\n", STM32_I2C_OAR2(port));
CPRINTF("DR : %016b\n", STM32_I2C_DR(port));
CPRINTF("CCR : %016b\n", STM32_I2C_CCR(port));
CPRINTF("TRISE: %016b\n", STM32_I2C_TRISE(port));
#endif /* CONFIG_I2C_DEBUG */
}
