void BoardInitMcu( void )
{
if( McuInitialized == false )
{
// We use IRQ priority group 4 for the entire project
// When setting the IRQ, only the preemption priority is used
NVIC_PriorityGroupConfig( NVIC_PriorityGroup_4 );
// Disable Systick
SysTick->CTRL &= ~SysTick_CTRL_TICKINT_Msk; // Systick IRQ off
SCB->ICSR |= SCB_ICSR_PENDSTCLR_Msk; // Clear SysTick Exception pending flag
AdcInit( &Adc, POTI );
SpiInit( &SX1272.Spi, RADIO_MOSI, RADIO_MISO, RADIO_SCLK, NC );
SX1272IoInit( );
#if( LOW_POWER_MODE_ENABLE )
TimerSetLowPowerEnable( true );
#else
TimerSetLowPowerEnable( false );
#endif
BoardUnusedIoInit( );
if( TimerGetLowPowerEnable( ) == true )
{
RtcInit( );
}
else
{
TimerHwInit( );
}
McuInitialized = true;
}
}
void BoardInitMcu( void )
{
Gpio_t ioPin;
if( McuInitialized == false )
{
HAL_Init( );
// LEDs
GpioInit( &Led1, LED_1, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, 1 );
GpioInit( &Led2, LED_2, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, 1 );
GpioInit( &Led3, LED_3, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, Led3Status );
SystemClockConfig( );
GpioInit( &ioPin, UART_RX, PIN_INPUT, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
if( GpioRead( &ioPin ) == 1 ) // Debug Mode
{
UsbIsConnected = true;
FifoInit( &Uart1.FifoTx, UartTxBuffer, UART_FIFO_TX_SIZE );
FifoInit( &Uart1.FifoRx, UartRxBuffer, UART_FIFO_RX_SIZE );
// Configure your terminal for 8 Bits data (7 data bit + 1 parity bit), no parity and no flow ctrl
UartInit( &Uart1, UART_1, UART_TX, UART_RX );
UartConfig( &Uart1, RX_TX, 115200, UART_8_BIT, UART_1_STOP_BIT, NO_PARITY, NO_FLOW_CTRL );
}
else
{
UsbIsConnected = false;
UartDeInit( &Uart1 );
}
RtcInit( );
BoardUnusedIoInit( );
}
else
{
SystemClockReConfig( );
}
I2cInit( &I2c, I2C_SCL, I2C_SDA );
AdcInit( &Adc, BAT_LEVEL_PIN );
SpiInit( &SX1272.Spi, RADIO_MOSI, RADIO_MISO, RADIO_SCLK, NC );
SX1272IoInit( );
if( McuInitialized == false )
{
McuInitialized = true;
if( GetBoardPowerSource( ) == BATTERY_POWER )
{
CalibrateSystemWakeupTime( );
}
}
}
void BoardInitMcu( void )
{
if( McuInitialized == false )
{
#if defined( USE_BOOTLOADER )
// Set the Vector Table base location at 0x3000
NVIC_SetVectorTable( NVIC_VectTab_FLASH, 0x3000 );
#endif
// We use IRQ priority group 4 for the entire project
// When setting the IRQ, only the preemption priority is used
NVIC_PriorityGroupConfig( NVIC_PriorityGroup_4 );
// Disable Systick
SysTick->CTRL &= ~SysTick_CTRL_TICKINT_Msk; // Systick IRQ off
SCB->ICSR |= SCB_ICSR_PENDSTCLR_Msk; // Clear SysTick Exception pending flag
I2cInit( &I2c, I2C_SCL, I2C_SDA );
AdcInit( &Adc, BAT_LEVEL );
SpiInit( &SX1272.Spi, RADIO_MOSI, RADIO_MISO, RADIO_SCLK, NC );
SX1272IoInit( );
#if defined( USE_DEBUG_PINS )
GpioInit( &DbgPin1, CON_EXT_1, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
GpioInit( &DbgPin2, CON_EXT_3, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
GpioInit( &DbgPin3, CON_EXT_7, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
GpioInit( &DbgPin4, CON_EXT_9, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
#endif
BoardUnusedIoInit( );
#if defined( USE_USB_CDC )
UsbMcuInit( );
UartInit( &UartUsb, UART_USB_CDC, NC, NC );
UartConfig( &UartUsb, RX_TX, 115200, UART_8_BIT, UART_1_STOP_BIT, NO_PARITY, NO_FLOW_CTRL );
#endif
#ifdef LOW_POWER_MODE_ENABLE
RtcInit( );
#else
TimerHwInit( );
#endif
McuInitialized = true;
}
}
void BoardInitMcu( void )
{
if( McuInitialized == false )
{
#if defined( USE_BOOTLOADER )
// Set the Vector Table base location at 0x3000
SCB->VTOR = FLASH_BASE | 0x3000;
#endif
HAL_Init( );
SystemClockConfig( );
#if defined( USE_USB_CDC )
UartInit( &UartUsb, UART_USB_CDC, NC, NC );
UartConfig( &UartUsb, RX_TX, 115200, UART_8_BIT, UART_1_STOP_BIT, NO_PARITY, NO_FLOW_CTRL );
DelayMs( 1000 ); // 1000 ms for Usb initialization
#endif
RtcInit( );
BoardUnusedIoInit( );
I2cInit( &I2c, I2C_1, I2C_SCL, I2C_SDA );
}
else
{
SystemClockReConfig( );
}
AdcInit( &Adc, BAT_LEVEL_PIN );
SpiInit( &SX1272.Spi, SPI_1, RADIO_MOSI, RADIO_MISO, RADIO_SCLK, NC );
SX1272IoInit( );
if( McuInitialized == false )
{
McuInitialized = true;
if( GetBoardPowerSource( ) == BATTERY_POWER )
{
CalibrateSystemWakeupTime( );
}
}
}
void BoardInitMcu( void )
{
if( McuInitialized == false )
{
// We use IRQ priority group 4 for the entire project
// When setting the IRQ, only the preemption priority is used
NVIC_PriorityGroupConfig( NVIC_PriorityGroup_4 );
// Disable Systick
SysTick->CTRL &= ~SysTick_CTRL_TICKINT_Msk; // Systick IRQ off
SCB->ICSR |= SCB_ICSR_PENDSTCLR_Msk; // Clear SysTick Exception pending flag
I2cInit( &I2c, I2C_SCL, I2C_SDA );
SpiInit( &SX1272.Spi, RADIO_MOSI, RADIO_MISO, RADIO_SCLK, NC );
SX1272IoInit( );
#if defined( USE_DEBUG_PINS )
GpioInit( &DbgPin1, J5_1, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
GpioInit( &DbgPin2, J5_2, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
GpioInit( &DbgPin3, J5_3, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
GpioInit( &DbgPin4, J5_4, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, 0 );
#endif
BoardInitPeriph( );
#if( LOW_POWER_MODE_ENABLE )
TimerSetLowPowerEnable( true );
#else
TimerSetLowPowerEnable( false );
#endif
BoardUnusedIoInit( );
if( TimerGetLowPowerEnable( ) == true )
{
RtcInit( );
}
else
{
TimerHwInit( );
}
McuInitialized = true;
}
}
void BoardInitMcu( void )
{
if( McuInitialized == false )
{
/* Chip errata */
CHIP_Init();
CMU_OscillatorEnable(cmuOsc_HFXO, true, true);
CMU_ClockSelectSet(cmuClock_HF,cmuSelect_HFXO);
/* Enable clock for HF peripherals */
CMU_ClockEnable(cmuClock_HFPER, true);
CMU_ClockEnable(cmuClock_GPIO, true);
GpioInit( &Led1, LED_1, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, LED_1_ON_STATE );
GpioInit( &Led2, LED_2, PIN_OUTPUT, PIN_PUSH_PULL, PIN_NO_PULL, LED_2_ON_STATE );
#ifdef USE_I2C
I2cInit( &I2c, I2C_SCL, I2C_SDA );
#endif
SX1272IoInit( );
SpiInit( &SX1272.Spi, RADIO_MOSI, RADIO_MISO, RADIO_SCLK, NC );
BoardUnusedIoInit( );
#ifdef LOW_POWER_MODE_ENABLE
#error LOW_POWER_MODE_ENABLE not supported
RtcInit( );
#else
TimerHwInit( );
#endif
Led_1_Off();
Led_2_Off();
McuInitialized = true;
}
}
