/*********************************************************************************************************
** Function name: SetFanPwm
** Descriptions:
** input parameters:
**
** Output parameters:: нч
** Returned value:
**
** Created by:
** Created Date:
**--------------------------------------------------------------------------------------------------------
** Modified by:
** Modified date:
**--------------------------------------------------------------------------------------------------------
*********************************************************************************************************/
u8 GetFanPwm()
{
// Set the Timer1B match value to load value / 3.
//
return (TimerMatchGet(WTIMER2_BASE, TIMER_B)*100)/TimerLoadGet(WTIMER2_BASE, TIMER_B);
}
/*---------------------------------------------------------------------------*/
PROCESS_THREAD(hello_world_process, ev, data)
{
static struct etimer timer;
static int count;
PROCESS_BEGIN();
/* i2c_init(I2C_SCL_PORT, I2C_SCL_PIN, I2C_SDA_PORT, I2C_SDA_PIN,
I2C_SCL_NORMAL_BUS_SPEED);*/
etimer_set(&timer, CLOCK_CONF_SECOND * 1);
count = 0;
relay_enable(PORT_D,LED_RELAY_PIN);
while(1) {
PROCESS_WAIT_EVENT();
if(ev == PROCESS_EVENT_TIMER) {
if(count %2 == 0){
//relay_on(PORT_D,LED_RELAY_PIN);
int delayIndex;
unsigned int pwmDutyCycle = 0x0000;
//
// Initialize the interrupt counter.
//
int g_ui32Counter = 0;
//
// Set the clocking to run directly from the external crystal/oscillator.
// (no ext 32k osc, no internal osc)
//
SysCtrlClockSet(false, false, 32000000);
//
// Set IO clock to the same as system clock
//
SysCtrlIOClockSet(32000000);
//
// The Timer0 peripheral must be enabled for use.
//
SysCtrlPeripheralEnable(SYS_CTRL_PERIPH_GPT0);
//
// Set up the serial console to use for displaying messages. This is
// just for this example program and is not needed for Timer operation.
//
//InitConsole();
//
// Display the example setup on the console.
//
UARTprintf("16-Bit Timer PWM ->");
UARTprintf("\n Timer = Timer0B");
UARTprintf("\n Mode = PWM with variable duty cycle");
//
// Configure GPTimer0A as a 16-bit PWM Timer.
//
TimerConfigure(GPTIMER0_BASE, GPTIMER_CFG_SPLIT_PAIR |
GPTIMER_CFG_A_PWM | GPTIMER_CFG_B_PWM);
//
// Set the GPTimer0B load value to 1sec by setting the timer load value
// to SYSCLOCK / 255. This is determined by:
// Prescaled clock = 16Mhz / 255
// Cycles to wait = 1sec * Prescaled clock
TimerLoadSet(GPTIMER0_BASE, GPTIMER_A, SysCtrlClockGet() / 4000);
TimerControlLevel(GPTIMER0_BASE, GPTIMER_A, false);
// Configure GPIOPortA.0 as the Timer0_InputCapturePin.1
IOCPinConfigPeriphOutput(GPIO_A_BASE, GPIO_PIN_0, IOC_MUX_OUT_SEL_GPT0_ICP1);
// Tell timer to use GPIOPortA.0
// Does Direction Selection and PAD Selection
GPIOPinTypeTimer(GPIO_A_BASE, GPIO_PIN_0);
//
// Enable processor interrupts.
//
IntMasterEnable();
//
// Enable GPTimer0B.
//
TimerEnable(GPTIMER0_BASE, GPTIMER_A);
UARTprintf("\n");
//
// Loop forever while the Timer0B runs.
//
while(1)
{
for (delayIndex = 0; delayIndex < 100000; delayIndex++);
pwmDutyCycle += 0x0F;
pwmDutyCycle &= 0xFFFF;
TimerMatchSet(GPTIMER0_BASE, GPTIMER_A, pwmDutyCycle);
UARTprintf("PWM DC Value: %04X -- %04X -- %04X\r",
pwmDutyCycle,
TimerValueGet(GPTIMER0_BASE, GPTIMER_A),
TimerMatchGet(GPTIMER0_BASE, GPTIMER_A) );
}
//SENSORS_ACTIVATE(cc2538_temp_sensor);
// printf( "%d is temp\n",cc2538_temp_sensor.value);
}
else {
//relay_off(PORT_D,LED_RELAY_PIN);
}
/* if(count %2 == 0)
{
relay_toggle(PORT_D,LED_RELAY_PIN);
relay_status(PORT_D,LED_RELAY_PIN);
}
*/
count ++;
etimer_reset(&timer);
}
}
PROCESS_END();
}
