/**
* This function resets the device but preserves the options set by the user.
*
* The descriptor list could be reinitialized with the same calls to
* XLlTemac_SgSetSpace() as used in main(). Doing this is a matter of preference.
* In many cases, an OS may have resources tied up in the descriptors.
* Reinitializing in this case may bad for the OS since its resources may be
* permamently lost.
*
* @param TemacInstancePtr is a pointer to the instance of the Temac
* component.
*
* @return XST_SUCCESS if successful, else XST_FAILURE.
*
* @note None.
*
******************************************************************************/
static int TemacResetDevice(XLlTemac * TemacInstancePtr,
XLlDma * DmaInstancePtr)
{
int Status;
u8 MacSave[6];
u32 Options;
//u32 RxThreshold = 1;
//u32 TxThreshold = 1;
//u32 RxWaitbound = 0;
//u32 TxWaitbound = 0;
//XLlDma_BdRing * RxRingPtr = &XLlDma_GetRxRing(DmaInstancePtr);
//XLlDma_BdRing * TxRingPtr = &XLlDma_GetTxRing(DmaInstancePtr);
/*
* Stop LLTEMAC device
*/
XLlTemac_Stop(TemacInstancePtr);
/*
* Save the device state
*/
XLlTemac_GetMacAddress(TemacInstancePtr, MacSave);
Options = XLlTemac_GetOptions(TemacInstancePtr);
/*
* Stop and reset the device
*/
XLlTemac_Reset(TemacInstancePtr, XTE_NORESET_HARD);
/*
* Restore the state
*/
Status = XLlTemac_SetMacAddress(TemacInstancePtr, MacSave);
Status |= XLlTemac_SetOptions(TemacInstancePtr, Options);
Status |= XLlTemac_ClearOptions(TemacInstancePtr, ~Options);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error restoring state after reset");
return XST_FAILURE;
}
/*
* Restart the device
*/
XLlTemac_Start(TemacInstancePtr);
return XST_SUCCESS;
}
/**
* This function resets the device but preserves the options set by the user.
*
* @param None.
*
* @return XST_SUCCESS if successful, else XST_FAILURE.
*
* @note None.
*
******************************************************************************/
int TemacResetDevice(void)
{
int Status;
u8 MacSave[6];
u32 Options;
/*
* Stop device
*/
XLlTemac_Stop(&TemacInstance);
/*
* Save the device state
*/
XLlTemac_GetMacAddress(&TemacInstance, MacSave);
Options = XLlTemac_GetOptions(&TemacInstance);
/*
* Stop and reset both the fifo and the temac the devices
*/
XLlFifo_Reset(&FifoInstance);
XLlTemac_Reset(&TemacInstance, XTE_NORESET_HARD);
/*
* Restore the state
*/
Status = XLlTemac_SetMacAddress(&TemacInstance, MacSave);
Status |= XLlTemac_SetOptions(&TemacInstance, Options);
Status |= XLlTemac_ClearOptions(&TemacInstance, ~Options);
if (Status != XST_SUCCESS) {
TemacUtilErrorTrap("Error restoring state after reset");
return XST_FAILURE;
}
return XST_SUCCESS;
}
void
init_lltemac(xlltemacif_s *xlltemacif, struct netif *netif)
{
int rdy;
unsigned mac_address = (unsigned)(netif->state);
unsigned link_speed = 1000;
unsigned options;
unsigned lock_message_printed = 0;
/* obtain config of this emac */
XLlTemac_Config *mac_config = lookup_config(mac_address);
XLlTemac *xlltemacp = &xlltemacif->lltemac;
XLlTemac_CfgInitialize(xlltemacp, mac_config, mac_config->BaseAddress);
options = XLlTemac_GetOptions(xlltemacp);
options |= XTE_FLOW_CONTROL_OPTION;
options |= XTE_JUMBO_OPTION;
options |= XTE_TRANSMITTER_ENABLE_OPTION;
options |= XTE_RECEIVER_ENABLE_OPTION;
options |= XTE_FCS_STRIP_OPTION;
options |= XTE_MULTICAST_OPTION;
XLlTemac_SetOptions(xlltemacp, options);
XLlTemac_ClearOptions(xlltemacp, ~options);
/* set mac address */
XLlTemac_SetMacAddress(xlltemacp, (Xuint8*)(netif->hwaddr));
/* make sure the hard TEMAC is ready */
rdy = XLlTemac_ReadReg(xlltemacp->Config.BaseAddress,
XTE_RDY_OFFSET);
while ((rdy & XTE_RDY_HARD_ACS_RDY_MASK) == 0) {
rdy = XLlTemac_ReadReg(xlltemacp->Config.BaseAddress,
XTE_RDY_OFFSET);
}
link_speed = Phy_Setup(xlltemacp);
XLlTemac_SetOperatingSpeed(xlltemacp, link_speed);
/* Setting the operating speed of the MAC needs a delay. */
{
volatile int wait;
for (wait=0; wait < 100000; wait++);
for (wait=0; wait < 100000; wait++);
}
/* in a soft temac implementation, we need to explicitly make sure that
* the RX DCM has been locked. See xps_ll_temac manual for details.
* This bit is guaranteed to be 1 for hard temac's
*/
lock_message_printed = 0;
while (!(XLlTemac_ReadReg(xlltemacp->Config.BaseAddress, XTE_IS_OFFSET)
& XTE_INT_RXDCM_LOCK_MASK)) {
int first = 1;
if (first) {
print("Waiting for RX DCM to lock..");
first = 0;
lock_message_printed = 1;
}
}
if (lock_message_printed)
print("RX DCM locked.\r\n");
/* start the temac */
XLlTemac_Start(xlltemacp);
/* enable TEMAC interrupts */
XLlTemac_IntEnable(xlltemacp, XTE_INT_RECV_ERROR_MASK);
}
