Esempi in C++ (Cpp) per at91_udp_hw_init

Esempio n. 1

File: board.c Progetto: 13xiaobang/mini2440-uboot_2016.01

int board_init(void)
{
	/* address of boot parameters */
	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

#ifdef CONFIG_CMD_NAND
	corvus_nand_hw_init();
#endif
#ifdef CONFIG_ATMEL_SPI
	at91_spi0_hw_init(1 << 4);
#endif
#ifdef CONFIG_HAS_DATAFLASH
	at91_spi0_hw_init(1 << 0);
#endif
#ifdef CONFIG_MACB
	corvus_macb_hw_init();
#endif
#ifdef CONFIG_CMD_USB
	taurus_usb_hw_init();
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	at91_udp_hw_init();
	usba_udc_probe(&pdata);
#endif
	return 0;
}

Esempio n. 2

File: sama5d4_xplained.c Progetto: RowanLiu/ported_uboot

int board_init(void)
{
	/* adress of boot parameters */
	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

#ifdef CONFIG_ATMEL_SPI
	sama5d4_xplained_spi0_hw_init();
#endif
#ifdef CONFIG_NAND_ATMEL
	sama5d4_xplained_nand_hw_init();
#endif
#ifdef CONFIG_GENERIC_ATMEL_MCI
	sama5d4_xplained_mci1_hw_init();
#endif
#ifdef CONFIG_MACB
	sama5d4_xplained_macb0_hw_init();
#endif
#ifdef CONFIG_LCD
	sama5d4_xplained_lcd_hw_init();
#endif
#ifdef CONFIG_CMD_USB
	sama5d4_xplained_usb_hw_init();
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	at91_udp_hw_init();
#endif

	return 0;
}

Esempio n. 3

File: board.c Progetto: CogSystems/u-boot

int board_init(void)
{
	/* address of boot parameters */
	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

	/* we have to request the gpios again after relocation */
	corvus_request_gpio();
#ifdef CONFIG_CMD_NAND
	corvus_nand_hw_init();
#endif
#ifdef CONFIG_ATMEL_SPI
	at91_spi0_hw_init(1 << 4);
#endif
#ifdef CONFIG_MACB
	corvus_macb_hw_init();
#endif
#ifdef CONFIG_CMD_USB
	taurus_usb_hw_init();
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	at91_udp_hw_init();
	usba_udc_probe(&pdata);
#endif
	return 0;
}

Esempio n. 4

File: ma5d4evk.c Progetto: OpenNoah/u-boot

int board_init(void)
{
	/* adress of boot parameters */
	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

#ifdef CONFIG_ATMEL_SPI
	ma5d4evk_spi0_hw_init();
#endif
#ifdef CONFIG_GENERIC_ATMEL_MCI
	ma5d4evk_mci0_hw_init();
	ma5d4evk_mci1_hw_init();
#endif
#ifdef CONFIG_MACB
	ma5d4evk_macb0_hw_init();
#endif
#ifdef CONFIG_LCD
	ma5d4evk_lcd_hw_init();
#endif
#ifdef CONFIG_CMD_USB
	ma5d4evk_usb_hw_init();
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	at91_udp_hw_init();
#endif

	board_identify();

	/* Reset CAN controllers */
	at91_set_pio_output(AT91_PIO_PORTB, 21, 0);
	udelay(100);
	at91_set_pio_output(AT91_PIO_PORTB, 21, 1);
	at91_pio3_set_pio_pulldown(AT91_PIO_PORTB, 21, 0);

	return 0;
}

Esempio n. 5

File: sama5d3xek.c Progetto: Philippe12/u-boot-sunxi

int board_init(void)
{
	/* adress of boot parameters */
	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

#ifdef CONFIG_NAND_ATMEL
	sama5d3xek_nand_hw_init();
#endif
#ifdef CONFIG_MTD_NOR_FLASH
	sama5d3xek_nor_hw_init();
#endif
#ifdef CONFIG_CMD_USB
	sama5d3xek_usb_hw_init();
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	at91_udp_hw_init();
#endif
#ifdef CONFIG_GENERIC_ATMEL_MCI
	sama5d3xek_mci_hw_init();
#endif
#ifdef CONFIG_ATMEL_SPI
	at91_spi0_hw_init(1 << 0);
#endif
#ifdef CONFIG_MACB
	if (has_emac())
		at91_macb_hw_init();
	if (has_gmac())
		at91_gmac_hw_init();
#endif
#ifdef CONFIG_LCD
	if (has_lcdc())
		sama5d3xek_lcd_hw_init();
#endif
	return 0;
}

Esempio n. 6

File: sama5d2_xplained.c Progetto: jacobbarsoe/u-boot-at91

int board_init(void)
{
	/* adress of boot parameters */
	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

#ifdef CONFIG_ATMEL_SPI
	board_spi0_hw_init();
#endif
#ifdef CONFIG_ATMEL_QSPI
	board_qspi_hw_init();
#endif
#ifdef CONFIG_ATMEL_SDHCI
#ifdef CONFIG_ATMEL_SDHCI0
	board_sdhci0_hw_init();
#endif
#ifdef CONFIG_ATMEL_SDHCI1
	board_sdhci1_hw_init();
#endif
#endif
#ifdef CONFIG_MACB
	board_gmac_hw_init();
#endif
#ifdef CONFIG_LCD
	board_lcd_hw_init();
#endif
#ifdef CONFIG_CMD_USB
	board_usb_hw_init();
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	at91_udp_hw_init();
#endif

	return 0;
}

Esempio n. 7

File: sama5d4ek.c Progetto: Android4SAM/u-boot-at91

int board_init(void)
{
	/* adress of boot parameters */
	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

#ifdef CONFIG_ATMEL_SPI
	sama5d4ek_spi0_hw_init();
#endif
#ifdef CONFIG_NAND_ATMEL
	sama5d4ek_nand_hw_init();
#endif
#ifdef CONFIG_GENERIC_ATMEL_MCI
	sama5d4ek_mci1_hw_init();
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	at91_udp_hw_init();
#endif
#ifdef CONFIG_MACB
	sama5d4ek_macb0_hw_init();
#endif
#ifdef CONFIG_MACB1
	sama5d4ek_macb1_hw_init();
#else
#ifdef CONFIG_LCD
	sama5d4ek_lcd_hw_init();
#endif
#endif
#ifdef CONFIG_CMD_USB
	sama5d4ek_usb_hw_init();
#endif
#ifdef CONFIG_ANDROID_RECOVERY
	recovery_button_hw_init();
	check_recovery_button();
#endif
#ifdef CONFIG_CMD_FASTBOOT
       fastboot_button_hw_init();
#endif

	return 0;
}

Esempio n. 8

File: vinco.c Progetto: 01hyang/u-boot

int board_init(void)
{
	/* adress of boot parameters */
	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

#ifdef CONFIG_ATMEL_SPI
	vinco_spi0_hw_init();
#endif

#ifdef CONFIG_GENERIC_ATMEL_MCI
	vinco_mci0_hw_init();
#endif
#ifdef CONFIG_MACB
	vinco_macb0_hw_init();
#endif
#ifdef CONFIG_CMD_USB
	vinco_usb_hw_init();
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
	at91_udp_hw_init();
#endif

	return 0;
}