static void __init omap3_beagle_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_beagle_init_rev();
omap3_beagle_i2c_init();
platform_add_devices(omap3_beagle_devices,
ARRAY_SIZE(omap3_beagle_devices));
omap_serial_init();
omap_mux_init_gpio(170, OMAP_PIN_INPUT);
gpio_request(170, "DVI_nPD");
/* REVISIT leave DVI powered down until it's needed ... */
gpio_direction_output(170, true);
usb_musb_init(&musb_board_data);
usb_ehci_init(&ehci_pdata);
omap3beagle_flash_init();
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
beagle_display_init();
#ifdef CONFIG_USB_ANDROID
omap3beagle_android_gadget_init();
#endif
omap3_beagle_pm_init();
}
static void __init omap3_beagle_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_beagle_init_rev();
omap3_beagle_i2c_init();
gpio_buttons[0].gpio = beagle_config.usr_button_gpio;
platform_add_devices(omap3_beagle_devices,
ARRAY_SIZE(omap3_beagle_devices));
omap_display_init(&beagle_dss_data);
omap_serial_init();
omap_sdrc_init(mt46h32m32lf6_sdrc_params,
mt46h32m32lf6_sdrc_params);
omap_mux_init_gpio(170, OMAP_PIN_INPUT);
/* REVISIT leave DVI powered down until it's needed ... */
gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,
ARRAY_SIZE(omap3beagle_nand_partitions));
/* Ensure msecure is mux'd to be able to set the RTC. */
omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
beagle_display_init();
beagle_opp_init();
}
static void __init omap3_beagle_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_beagle_init_rev();
omap3_beagle_i2c_init();
gpio_buttons[0].gpio = beagle_config.usr_button_gpio;
platform_add_devices(omap3_beagle_devices,
ARRAY_SIZE(omap3_beagle_devices));
omap_display_init(&beagle_dss_data);
omap_serial_init();
usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,
ARRAY_SIZE(omap3beagle_nand_partitions));
/* Ensure msecure is mux'd to be able to set the RTC. */
omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
beagle_display_init();
beagle_opp_init();
}
static void __init omap3_beagle_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_beagle_init_rev();
omap3_beagle_i2c_init();
platform_add_devices(omap3_beagle_devices,
ARRAY_SIZE(omap3_beagle_devices));
omap_display_init(&beagle_dss_data);
omap_serial_init();
omap_mux_init_gpio(170, OMAP_PIN_INPUT);
/* REVISIT leave DVI powered down until it's needed ... */
gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,
ARRAY_SIZE(omap3beagle_nand_partitions));
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
beagle_display_init();
beagle_opp_init();
}
static void __init omap3_beagle_init(void)
{
omap3_beagle_i2c_init();
platform_add_devices(omap3_beagle_devices,
ARRAY_SIZE(omap3_beagle_devices));
omap_board_config = omap3_beagle_config;
omap_board_config_size = ARRAY_SIZE(omap3_beagle_config);
omap_serial_init();
omap_cfg_reg(J25_34XX_GPIO170);
usb_musb_init();
usb_ehci_init();
omap3beagle_flash_init();
beagle_display_init();
}
static void __init omap3_beagle_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_beagle_init_rev();
omap3_beagle_i2c_init();
platform_add_devices(omap3_beagle_devices,
ARRAY_SIZE(omap3_beagle_devices));
omap_display_init(&beagle_dss_data);
omap_serial_init();
usb_musb_init(&musb_board_data);
usbhs_init(&usbhs_bdata);
omap3beagle_flash_init();
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
beagle_display_init();
beagle_opp_init();
}
static void __init omap3_beagle_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_beagle_i2c_init();
platform_add_devices(omap3_beagle_devices,
ARRAY_SIZE(omap3_beagle_devices));
omap_serial_init();
omap_mux_init_gpio(170, OMAP_PIN_INPUT);
gpio_request(170, "DVI_nPD");
/* REVISIT leave DVI powered down until it's needed ... */
gpio_direction_output(170, true);
//omap_mux_init_gpio(GPIO_IRQ, OMAP_PIN_INPUT); //W-Y-L GPIO 133
//omap_mux_init_gpio(GPIO_DIR, OMAP_PIN_INPUT_PULLDOWN); //W-Y-L GPIO 137
if(!strcmp(expansionboard_name, "zippy"))
{
printk(KERN_INFO "Beagle expansionboard: initializing enc28j60\n");
omap3beagle_enc28j60_init();
printk(KERN_INFO "Beagle expansionboard: assigning GPIO 141 and 162 to MMC1\n");
mmc[1].gpio_wp = 141;
mmc[1].gpio_cd = 162;
}
if(!strcmp(expansionboard_name, "zippy2"))
{
printk(KERN_INFO "Beagle expansionboard: initializing ks_8851\n");
omap3beagle_ks8851_init();
printk(KERN_INFO "Beagle expansionboard: assigning GPIO 141 and 162 to MMC1\n");
mmc[1].gpio_wp = 141;
mmc[1].gpio_cd = 162;
}
if(!strcmp(expansionboard_name, "trainer"))
{
printk(KERN_INFO "Beagle expansionboard: exporting GPIOs 130-141,162 to userspace\n");
gpio_request(130, "sysfs");
gpio_export(130, 1);
gpio_request(131, "sysfs");
gpio_export(131, 1);
gpio_request(132, "sysfs");
gpio_export(132, 1);
gpio_request(133, "sysfs");
gpio_export(133, 1);
gpio_request(134, "sysfs");
gpio_export(134, 1);
gpio_request(135, "sysfs");
gpio_export(135, 1);
gpio_request(136, "sysfs");
gpio_export(136, 1);
gpio_request(137, "sysfs");
gpio_export(137, 1);
gpio_request(138, "sysfs");
gpio_export(138, 1);
gpio_request(139, "sysfs");
gpio_export(139, 1);
gpio_request(140, "sysfs");
gpio_export(140, 1);
gpio_request(141, "sysfs");
gpio_export(141, 1);
gpio_request(162, "sysfs");
gpio_export(162, 1);
}
usb_musb_init();
usb_ehci_init(&ehci_pdata);
omap3beagle_flash_init();
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
beagle_display_init();
#ifdef CONFIG_USB_ANDROID
omap3evm_android_gadget_init();
#endif
}
/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
struct control_prog_io *prog_io_base = (struct control_prog_io *)OMAP34XX_CTRL_BASE;
/* Enable i2c2 pullup resisters */
writel(~(PRG_I2C2_PULLUPRESX), &prog_io_base->io1);
switch (get_board_revision()) {
case REVISION_AXBX:
printf("Beagle Rev Ax/Bx\n");
setenv("beaglerev", "AxBx");
break;
case REVISION_CX:
printf("Beagle Rev C1/C2/C3\n");
setenv("beaglerev", "Cx");
MUX_BEAGLE_C();
break;
case REVISION_C4:
printf("Beagle Rev C4\n");
setenv("beaglerev", "C4");
MUX_BEAGLE_C();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
case REVISION_XM_AB:
printf("Beagle xM Rev A/B\n");
setenv("beaglerev", "xMAB");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
case REVISION_XM_C:
printf("Beagle xM Rev C\n");
setenv("beaglerev", "xMC");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
default:
printf("Beagle unknown 0x%02x\n", get_board_revision());
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
}
switch (get_expansion_id()) {
case TINCANTOOLS_ZIPPY:
printf("Recognized Tincantools Zippy board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
setenv("buddy", "zippy");
break;
case TINCANTOOLS_ZIPPY2:
printf("Recognized Tincantools Zippy2 board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
setenv("buddy", "zippy2");
break;
case TINCANTOOLS_TRAINER:
printf("Recognized Tincantools Trainer board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
MUX_TINCANTOOLS_TRAINER();
setenv("buddy", "trainer");
break;
case TINCANTOOLS_SHOWDOG:
printf("Recognized Tincantools Showdow board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
/* Place holder for DSS2 definition for showdog lcd */
setenv("defaultdisplay", "showdoglcd");
setenv("buddy", "showdog");
break;
case KBADC_BEAGLEFPGA:
printf("Recognized KBADC Beagle FPGA board\n");
MUX_KBADC_BEAGLEFPGA();
setenv("buddy", "beaglefpga");
break;
case LW_BEAGLETOUCH:
printf("Recognized Liquidware BeagleTouch board\n");
setenv("buddy", "beagletouch");
break;
case BRAINMUX_LCDOG:
printf("Recognized Brainmux LCDog board\n");
setenv("buddy", "lcdog");
break;
case BRAINMUX_LCDOGTOUCH:
printf("Recognized Brainmux LCDog Touch board\n");
setenv("buddy", "lcdogtouch");
break;
case BBTOYS_WIFI:
printf("Recognized BeagleBoardToys WiFi board\n");
MUX_BBTOYS_WIFI()
setenv("buddy", "bbtoys-wifi");
break;;
case BBTOYS_VGA:
printf("Recognized BeagleBoardToys VGA board\n");
break;;
case BBTOYS_LCD:
printf("Recognized BeagleBoardToys LCD board\n");
break;;
case BCT_BRETTL3:
printf("Recognized bct electronic GmbH brettl3 board\n");
break;
case BCT_BRETTL4:
printf("Recognized bct electronic GmbH brettl4 board\n");
break;
case LSR_COM6L_ADPT:
printf("Recognized LSR COM6L Adapter Board\n");
MUX_BBTOYS_WIFI()
setenv("buddy", "lsr-com6l-adpt");
break;
case BEAGLE_NO_EEPROM:
printf("No EEPROM on expansion board\n");
setenv("buddy", "none");
break;
default:
printf("Unrecognized expansion board: %x\n",
expansion_config.device_vendor);
setenv("buddy", "unknown");
}
if (expansion_config.content == 1)
setenv(expansion_config.env_var, expansion_config.env_setting);
twl4030_power_init();
switch (get_board_revision()) {
case REVISION_XM_AB:
twl4030_led_init(TWL4030_LED_LEDEN_LEDBON);
break;
default:
twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
break;
}
/* Set GPIO states before they are made outputs */
writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
&gpio6_base->setdataout);
writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
/* Configure GPIOs to output */
writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
dieid_num_r();
#ifdef CONFIG_VIDEO_OMAP3
beagle_dvi_pup();
beagle_display_init();
omap3_dss_enable();
#endif
#ifdef CONFIG_USB_MUSB_OMAP2PLUS
musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE);
#endif
return 0;
}
static void __init omap3_beagle_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_beagle_init_rev();
omap3_beagle_i2c_init();
if (cpu_is_omap3630()) {
gpio_buttons[0].gpio = 4;
}
platform_add_devices(omap3_beagle_devices,
ARRAY_SIZE(omap3_beagle_devices));
omap_serial_init();
omap_mux_init_gpio(170, OMAP_PIN_INPUT);
gpio_request(170, "DVI_nPD");
/* REVISIT leave DVI powered down until it's needed ... */
gpio_direction_output(170, true);
if(!strcmp(expansionboard_name, "zippy"))
{
printk(KERN_INFO "Beagle expansionboard: initializing enc28j60\n");
omap3beagle_enc28j60_init();
printk(KERN_INFO "Beagle expansionboard: assigning GPIO 141 and 162 to MMC1\n");
mmc[1].gpio_wp = 141;
mmc[1].gpio_cd = 162;
}
if(!strcmp(expansionboard_name, "zippy2"))
{
printk(KERN_INFO "Beagle expansionboard: initializing ks_8851\n");
omap3beagle_ks8851_init();
printk(KERN_INFO "Beagle expansionboard: assigning GPIO 141 and 162 to MMC1\n");
mmc[1].gpio_wp = 141;
mmc[1].gpio_cd = 162;
}
if(!strcmp(expansionboard_name, "trainer"))
{
printk(KERN_INFO "Beagle expansionboard: exporting GPIOs 130-141,162 to userspace\n");
gpio_request(130, "sysfs");
gpio_export(130, 1);
gpio_request(131, "sysfs");
gpio_export(131, 1);
gpio_request(132, "sysfs");
gpio_export(132, 1);
gpio_request(133, "sysfs");
gpio_export(133, 1);
gpio_request(134, "sysfs");
gpio_export(134, 1);
gpio_request(135, "sysfs");
gpio_export(135, 1);
gpio_request(136, "sysfs");
gpio_export(136, 1);
gpio_request(137, "sysfs");
gpio_export(137, 1);
gpio_request(138, "sysfs");
gpio_export(138, 1);
gpio_request(139, "sysfs");
gpio_export(139, 1);
gpio_request(140, "sysfs");
gpio_export(140, 1);
gpio_request(141, "sysfs");
gpio_export(141, 1);
gpio_request(162, "sysfs");
gpio_export(162, 1);
}
#if defined(CONFIG_WL1271) || defined(CONFIG_WL1271_MODULE)
if(!strcmp(expansionboard_name, "bbtoys-wifi"))
{
if (wl12xx_set_platform_data(&omap_beagle_wlan_data))
pr_err("error setting wl12xx data\n");
printk(KERN_INFO "Beagle expansionboard: registering wl12xx platform device\n");
platform_device_register(&omap_vwlan_device);
}
#endif
usb_musb_init(&musb_board_data);
usb_ehci_init(&ehci_pdata);
omap3beagle_flash_init();
/* Ensure msecure is mux'd to be able to set the RTC. */
omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
beagle_display_init();
beagle_opp_init();
}
/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
struct control_prog_io *prog_io_base = (struct control_prog_io *)OMAP34XX_CTRL_BASE;
/* Enable i2c2 pullup resisters */
writel(~(PRG_I2C2_PULLUPRESX), &prog_io_base->io1);
switch (get_board_revision()) {
case REVISION_AXBX:
printf("Beagle Rev Ax/Bx\n");
setenv("beaglerev", "AxBx");
break;
case REVISION_CX:
printf("Beagle Rev C1/C2/C3\n");
setenv("beaglerev", "Cx");
MUX_BEAGLE_C();
break;
case REVISION_C4:
printf("Beagle Rev C4\n");
setenv("beaglerev", "C4");
MUX_BEAGLE_C();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
case REVISION_XM_A:
printf("Beagle xM Rev A\n");
setenv("beaglerev", "xMA");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
case REVISION_XM_B:
printf("Beagle xM Rev B\n");
setenv("beaglerev", "xMB");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
case REVISION_XM_C:
printf("Beagle xM Rev C\n");
setenv("beaglerev", "xMC");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
default:
printf("Beagle unknown 0x%02x\n", get_board_revision());
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
}
switch (get_expansion_id(EXPANSION_EEPROM_I2C_ADDRESS)) {
case TINCANTOOLS_ZIPPY:
printf("Recognized Tincantools Zippy board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
setenv("buddy", "zippy");
break;
case TINCANTOOLS_ZIPPY2:
printf("Recognized Tincantools Zippy2 board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
setenv("buddy", "zippy2");
break;
case TINCANTOOLS_TRAINER:
printf("Recognized Tincantools Trainer board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
MUX_TINCANTOOLS_TRAINER();
setenv("buddy", "trainer");
break;
case TINCANTOOLS_SHOWDOG:
printf("Recognized Tincantools Showdow board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
/* Place holder for DSS2 definition for showdog lcd */
setenv("defaultdisplay", "showdoglcd");
setenv("buddy", "showdog");
break;
case TINCANTOOLS_BEACON:
printf("Recognized Tincantools Beacon board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_BEACON();
setenv("buddy", "beacon");
break;
case KBADC_BEAGLEFPGA:
printf("Recognized KBADC Beagle FPGA board\n");
MUX_KBADC_BEAGLEFPGA();
setenv("buddy", "beaglefpga");
break;
case LW_BEAGLETOUCH:
printf("Recognized Liquidware BeagleTouch board\n");
setenv("buddy", "beagletouch");
break;
case BRAINMUX_LCDOG:
printf("Recognized Brainmux LCDog board\n");
setenv("buddy", "lcdog");
break;
case BRAINMUX_LCDOGTOUCH:
printf("Recognized Brainmux LCDog Touch board\n");
setenv("buddy", "lcdogtouch");
break;
case BBTOYS_WIFI:
printf("Recognized BeagleBoardToys WiFi board\n");
MUX_BBTOYS_WIFI()
setenv("buddy", "bbtoys-wifi");
break;;
case BBTOYS_VGA:
printf("Recognized BeagleBoardToys VGA board\n");
break;;
case BBTOYS_LCD:
printf("Recognized BeagleBoardToys LCD board\n");
break;;
case BEAGLE_NO_EEPROM:
printf("No EEPROM on expansion board\n");
setenv("buddy", "none");
break;
default:
printf("Unrecognized expansion board: %x\n",
expansion_config.device_vendor);
setenv("buddy", "unknown");
}
if (expansion_config.content == 1)
setenv(expansion_config.env_var, expansion_config.env_setting);
/* Scan 0x51 as well for loop-thru boards */
switch (get_expansion_id(EXPANSION_EEPROM_I2C_ADDRESS + 1)) {
case BBTOYS_ULCD:
printf("Recognized BeagleBoardToys uLCD-lite board\n");
setenv("buddy2", "bbtoys-ulcd");
setenv("defaultdisplay", "lcd");
setenv("uenvcmd", "i2c dev 1 ; i2c mw 40 00 00; i2c mw 40 04 80; i2c mw 40 0d 05; i2c mw 40 0d 15");
break;
case BEAGLE_NO_EEPROM:
printf("No EEPROM on expansion board\n");
setenv("buddy2", "none");
break;
default:
printf("Unrecognized expansion board: %x\n",
expansion_config.device_vendor);
setenv("buddy2", "unknown");
}
if (expansion_config.content == 1)
setenv(expansion_config.env_var, expansion_config.env_setting);
twl4030_power_init();
switch (get_board_revision()) {
case REVISION_XM_A:
case REVISION_XM_B:
twl4030_led_init(TWL4030_LED_LEDEN_LEDBON);
break;
default:
twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
break;
}
/* Set GPIO states before they are made outputs */
writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
&gpio6_base->setdataout);
writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
/* Configure GPIOs to output */
writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
dieid_num_r();
beagle_display_init();
omap3_dss_enable();
return 0;
}
