/* This is an entry point for the application.
All application specific initialization is performed here. */
int main(void)
{
int ret = 0;
/* Initializes console on UART0 */
ret = wmstdio_init(UART0_ID, 0);
if (ret == -WM_FAIL) {
wmprintf("Failed to initialize console on uart0\r\n");
return -1;
}
wmprintf(" LED demo application started\r\n");
wmprintf(" This application demonstrates the"
" use of blinking led\r\n");
gpio_led = (board_led_2()).gpio;
wmprintf(" LED Pin : %d\r\n", gpio_led);
configure_gpios();
while (1) {
gpio_led_on();
os_thread_sleep(os_msec_to_ticks(1000));
gpio_led_off();
os_thread_sleep(os_msec_to_ticks(1000));
}
return 0;
}
void reset(void) //same function as main()
{
char str[]="sunny,sunny day";//inputs are given
char w[]="sunny";
wmprintf("entered string is :%s\n",str);//inputs are outputed
wmprintf("entered word :%s\n",w);
int wcount = count(str,w);
wmprintf("word count : %d\n",wcount);
if (wcount>0)
{
gpio_led_on()
}
gpio_led = (board_led_2()).gpio; //assigning gpio pin to led
gpio_pushbutton = board_button_2(); //assigning gpio pin to push button
configure_gpios();
wmprintf("Press push button to reset the program.");
while (1)
;
return 0;
}
//Main function, the entry point
int main(void)
{
int uart_check = 0,i=0,j=0;
char str[]="sunny,sunny day";//inputs are given
char w[]="sunny";
//Checking the status of UART
uart_check = wmstdio_init(UART0_ID, 0);
if (uart_check == -WM_FAIL) {
wmprintf("Failed to initialize console on uart0\r\n");
return -1;
}
wmprintf("entered string is :%s\n",str);//inputs are outputed
wmprintf("entered word :%s\n",w);
int wcount = count(str,w);//ouputting total words
wmprintf("word count : %d\n",wcount);
if (wcount>0)
{
gpio_led_on()
}
gpio_led = (board_led_2()).gpio; //assigning gpio pin to led
gpio_pushbutton = board_button_2(); //assigning gpio pin to push button
configure_gpios();
wmprintf("Press push button to reset the program.");
while (1)
;
return 0;
}
/* This is an entry point for the application.
All application specific initialization is performed here. */
int main(void)
{
int ret = 0;
/* Initializes console on UART0 */
ret = wmstdio_init(UART0_ID, 0);
if (ret == -WM_FAIL) {
wmprintf("Failed to initialize console on uart0\r\n");
return -1;
}
wmprintf(" GPIO demo application started\r\n");
wmprintf(" This application demonstrates the"
" use of various GPIO driver APIs\r\n");
wmprintf(" Press button 2 to toggle state of LED\r\n");
gpio_led = (board_led_2()).gpio;
gpio_pushbutton = board_button_2();
wmprintf(" LED Pin : %d\r\n", gpio_led);
wmprintf(" Pushbutton Pin : %d\r\n", gpio_pushbutton);
configure_gpios();
while (1)
;
return 0;
}
/* Configure GPIO pins to be used as LED and push button */
static void configure_gpios()
{
/* Get the corresponding pin numbers using the board specific calls */
/* also configures the gpio accordingly for LED */
led_1 = board_led_1();
led_2 = board_led_2();
button_1 = board_button_1();
button_2 = board_button_2();
push_button_set_cb((input_gpio_cfg_t){button_1, GPIO_ACTIVE_LOW}, pushbutton_cb, 0, 0, 0);
push_button_set_cb((input_gpio_cfg_t){button_2, GPIO_ACTIVE_LOW}, pushbutton_cb, 0, 0, 0);
}
/* This is an entry point for the application.
All application specific initialization is performed here. */
int main(void)
{
int ret = 0;
TaskHandle_t blinkLEDHandle = NULL;
int priority;
/* Initializes console on UART0 */
ret = wmstdio_init(UART0_ID, 0);
if (ret == -WM_FAIL)
{
wmprintf("Failed to initialize console on uart0\r\n");
return -1;
}
wmprintf(" LED demo application started\r\n");
wmprintf(" This application demonstrates the"
" use of blinking led\r\n");
gpio_led = (board_led_2()).gpio;
wmprintf(" LED Pin : %d\r\n", gpio_led);
configure_gpios();
xTaskCreate(prvBlinkLedTask, "Blink led", ( uint16_t ) BLINK_LED_STACK_SIZE, NULL, ( ( UBaseType_t ) BLINK_LED_TASK_PRIORITY ) | portPRIVILEGE_BIT, &blinkLEDHandle);
// dump blink led task related information
if (NULL != blinkLEDHandle)
{
priority = uxTaskPriorityGet(blinkLEDHandle);
wmprintf("blink led priority is %d\r\n", priority);
wmprintf("blink led task name:%s\r\n", pcTaskGetTaskName(blinkLEDHandle));
}
wmprintf("run blink led task for 30 seconds\r\n");
vTaskDelay(30000);
wmprintf("delete blink led task\r\n");
if (NULL != blinkLEDHandle)
{
vTaskDelete(blinkLEDHandle);
blinkLEDHandle = NULL;
}
while (1)
{
vTaskDelay(1000);
}
return 0;
}
// TO override the pin start mode in mc200_startup.c, so that LED are off at startup
void SetPinStartMode(void)
{
GPIO_PinModeConfig(board_led_1().gpio, PINMODE_PULLUP);
GPIO_PinModeConfig(board_led_2().gpio, PINMODE_PULLUP);
}