/*
* This initializes the IO-APIC and APIC hardware if this is
* a UP kernel.
*/
int __init APIC_init_uniprocessor (void)
{
if (disable_apic) {
printk(KERN_INFO "Apic disabled\n");
return -1;
}
if (!cpu_has_apic) {
disable_apic = 1;
printk(KERN_INFO "Apic disabled by BIOS\n");
return -1;
}
verify_local_APIC();
connect_bsp_APIC();
phys_cpu_present_map = physid_mask_of_physid(boot_cpu_id);
apic_write(APIC_ID, SET_APIC_ID(boot_cpu_id));
setup_local_APIC();
#ifdef CONFIG_X86_IO_APIC
if (smp_found_config && !skip_ioapic_setup && nr_ioapics)
setup_IO_APIC();
else
nr_ioapics = 0;
#endif
setup_boot_APIC_clock();
check_nmi_watchdog();
return 0;
}
/*
* This initializes the IO-APIC and APIC hardware if this is
* a UP kernel.
*/
int __init APIC_init_uniprocessor (void)
{
if (enable_local_apic < 0)
clear_bit(X86_FEATURE_APIC, boot_cpu_data.x86_capability);
if (!smp_found_config && !cpu_has_apic)
return -1;
/*
* Complain if the BIOS pretends there is one.
*/
if (!cpu_has_apic && APIC_INTEGRATED(apic_version[boot_cpu_physical_apicid])) {
printk(KERN_ERR "BIOS bug, local APIC #%d not detected!...\n",
boot_cpu_physical_apicid);
clear_bit(X86_FEATURE_APIC, boot_cpu_data.x86_capability);
return -1;
}
verify_local_APIC();
connect_bsp_APIC();
phys_cpu_present_map = physid_mask_of_physid(boot_cpu_physical_apicid);
setup_local_APIC();
#ifdef CONFIG_X86_IO_APIC
if (smp_found_config)
if (!skip_ioapic_setup && nr_ioapics)
setup_IO_APIC();
#endif
setup_boot_APIC_clock();
return 0;
}
/*
* This initializes the IO-APIC and APIC hardware if this is
* a UP kernel.
*/
int __init APIC_init_uniprocessor (void)
{
if (!smp_found_config && !cpu_has_apic)
return -1;
/*
* Complain if the BIOS pretends there is one.
*/
if (!cpu_has_apic && APIC_INTEGRATED(apic_version[boot_cpu_physical_apicid])) {
printk(KERN_ERR "BIOS bug, local APIC #%d not detected!...\n",
boot_cpu_physical_apicid);
return -1;
}
verify_local_APIC();
connect_bsp_APIC();
phys_cpu_present_map = 1 << boot_cpu_physical_apicid;
apic_pm_init2();
setup_local_APIC();
if (nmi_watchdog == NMI_LOCAL_APIC)
check_nmi_watchdog();
#ifdef CONFIG_X86_IO_APIC
if (smp_found_config)
if (!skip_ioapic_setup && nr_ioapics)
setup_IO_APIC();
#endif
setup_APIC_clocks();
return 0;
}
/*
* This initializes the IO-APIC and APIC hardware if this is
* a UP kernel.
*/
int __init APIC_init_uniprocessor (void)
{
if (enable_local_apic < 0)
clear_bit(X86_FEATURE_APIC, boot_cpu_data.x86_capability);
if (!smp_found_config && !cpu_has_apic) {
skip_ioapic_setup = 1;
return -1;
}
/*
* Complain if the BIOS pretends there is one.
*/
if (!cpu_has_apic && APIC_INTEGRATED(apic_version[boot_cpu_physical_apicid])) {
printk(KERN_ERR "BIOS bug, local APIC #%d not detected!...\n",
boot_cpu_physical_apicid);
clear_bit(X86_FEATURE_APIC, boot_cpu_data.x86_capability);
skip_ioapic_setup = 1;
return -1;
}
verify_local_APIC();
connect_bsp_APIC();
/*
* Hack: In case of kdump, after a crash, kernel might be booting
* on a cpu with non-zero lapic id. But boot_cpu_physical_apicid
* might be zero if read from MP tables. Get it from LAPIC.
*/
#ifdef CONFIG_CRASH_DUMP
boot_cpu_physical_apicid = get_apic_id();
#endif
physids_clear(phys_cpu_present_map);
physid_set(boot_cpu_physical_apicid, phys_cpu_present_map);
setup_local_APIC();
if (nmi_watchdog == NMI_LOCAL_APIC)
check_nmi_watchdog();
#ifdef CONFIG_X86_IO_APIC
if (smp_found_config)
if (!skip_ioapic_setup && nr_ioapics)
setup_IO_APIC();
#endif
setup_boot_APIC_clock();
return 0;
}
/**
@brief prepare goto the smp mode
*/
static void x86_prepare_smp()
{
/* Find and Analyze the table from BIOS AND ACPI*/
mptable_find_smp_config();
mptable_get_smp_config();
/* This is called in init_IRQ */
init_bsp_APIC();
/* Connect apic */
connect_bsp_APIC();
setup_local_APIC();
bsp_end_local_APIC_setup();
printk("\n%s->%s->%d.",__FILE__,__FUNCTION__,__LINE__);
}
/*
* This initializes the IO-APIC and APIC hardware if this is
* a UP kernel.
*/
int __init APIC_init_uniprocessor (void)
{
if (apic_disabled)
clear_bit(X86_FEATURE_APIC, &boot_cpu_data.x86_capability);
if (!cpu_has_apic)
{
printk("No APIC available.\n");
apic_disabled = 1;
return -1;
}
/*
* Complain if the BIOS pretends there is one.
*/
if (!cpu_has_apic && APIC_INTEGRATED(apic_version[boot_cpu_id]))
{
printk(KERN_ERR "BIOS bug, local APIC #%d not detected!...\n",
boot_cpu_id);
apic_disabled = 1;
return -1;
}
verify_local_APIC();
connect_bsp_APIC();
phys_cpu_present_map = 1;
apic_write_around(APIC_ID, boot_cpu_id);
apic_pm_init2();
setup_local_APIC();
if (nmi_watchdog == NMI_LOCAL_APIC)
check_nmi_watchdog();
#ifdef CONFIG_X86_IO_APIC
if (smp_found_config && !skip_ioapic_setup && nr_ioapics)
setup_IO_APIC();
else
nr_ioapics = 0;
#endif
setup_APIC_clocks();
return 0;
}
/*
* This initializes the IO-APIC and APIC hardware if this is
* a UP kernel.
*/
int __init APIC_init_uniprocessor(void)
{
if (disable_apic) {
printk(KERN_INFO "Apic disabled\n");
return -1;
}
if (!cpu_has_apic) {
disable_apic = 1;
printk(KERN_INFO "Apic disabled by BIOS\n");
return -1;
}
verify_local_APIC();
connect_bsp_APIC();
physid_set_mask_of_physid(boot_cpu_physical_apicid, &phys_cpu_present_map);
apic_write(APIC_ID, SET_APIC_ID(boot_cpu_physical_apicid));
setup_local_APIC();
/*
* Now enable IO-APICs, actually call clear_IO_APIC
* We need clear_IO_APIC before enabling vector on BP
*/
if (!skip_ioapic_setup && nr_ioapics)
enable_IO_APIC();
if (!smp_found_config || skip_ioapic_setup || !nr_ioapics)
localise_nmi_watchdog();
end_local_APIC_setup();
if (smp_found_config && !skip_ioapic_setup && nr_ioapics)
setup_IO_APIC();
else
nr_ioapics = 0;
setup_boot_APIC_clock();
check_nmi_watchdog();
return 0;
}
static void __init smp_boot_cpus(unsigned int max_cpus)
{
int apicid, cpu, bit, kicked;
unsigned long bogosum = 0;
/*
* Setup boot CPU information
*/
smp_store_cpu_info(0); /* Final full version of the data */
printk("CPU%d: ", 0);
print_cpu_info(&cpu_data[0]);
boot_cpu_physical_apicid = GET_APIC_ID(apic_read(APIC_ID));
boot_cpu_logical_apicid = logical_smp_processor_id();
x86_cpu_to_apicid[0] = boot_cpu_physical_apicid;
current_thread_info()->cpu = 0;
smp_tune_scheduling();
cpus_clear(cpu_sibling_map[0]);
cpu_set(0, cpu_sibling_map[0]);
/*
* If we couldn't find an SMP configuration at boot time,
* get out of here now!
*/
if (!smp_found_config && !acpi_lapic) {
printk(KERN_NOTICE "SMP motherboard not detected.\n");
smpboot_clear_io_apic_irqs();
phys_cpu_present_map = physid_mask_of_physid(0);
if (APIC_init_uniprocessor())
printk(KERN_NOTICE "Local APIC not detected."
" Using dummy APIC emulation.\n");
map_cpu_to_logical_apicid();
return;
}
/*
* Should not be necessary because the MP table should list the boot
* CPU too, but we do it for the sake of robustness anyway.
* Makes no sense to do this check in clustered apic mode, so skip it
*/
if (!check_phys_apicid_present(boot_cpu_physical_apicid)) {
printk("weird, boot CPU (#%d) not listed by the BIOS.\n",
boot_cpu_physical_apicid);
physid_set(hard_smp_processor_id(), phys_cpu_present_map);
}
/*
* If we couldn't find a local APIC, then get out of here now!
*/
if (APIC_INTEGRATED(apic_version[boot_cpu_physical_apicid]) && !cpu_has_apic) {
printk(KERN_ERR "BIOS bug, local APIC #%d not detected!...\n",
boot_cpu_physical_apicid);
printk(KERN_ERR "... forcing use of dummy APIC emulation. (tell your hw vendor)\n");
smpboot_clear_io_apic_irqs();
phys_cpu_present_map = physid_mask_of_physid(0);
return;
}
verify_local_APIC();
/*
* If SMP should be disabled, then really disable it!
*/
if (!max_cpus) {
smp_found_config = 0;
printk(KERN_INFO "SMP mode deactivated, forcing use of dummy APIC emulation.\n");
smpboot_clear_io_apic_irqs();
phys_cpu_present_map = physid_mask_of_physid(0);
return;
}
connect_bsp_APIC();
setup_local_APIC();
map_cpu_to_logical_apicid();
setup_portio_remap();
/*
* Scan the CPU present map and fire up the other CPUs via do_boot_cpu
*
* In clustered apic mode, phys_cpu_present_map is a constructed thus:
* bits 0-3 are quad0, 4-7 are quad1, etc. A perverse twist on the
* clustered apic ID.
*/
Dprintk("CPU present map: %lx\n", physids_coerce(phys_cpu_present_map));
kicked = 1;
for (bit = 0; kicked < NR_CPUS && bit < MAX_APICS; bit++) {
apicid = cpu_present_to_apicid(bit);
/*
* Don't even attempt to start the boot CPU!
*/
if ((apicid == boot_cpu_apicid) || (apicid == BAD_APICID))
continue;
if (!check_apicid_present(bit))
continue;
if (max_cpus <= cpucount+1)
continue;
if (do_boot_cpu(apicid))
printk("CPU #%d not responding - cannot use it.\n",
apicid);
else
++kicked;
}
/*
* Cleanup possible dangling ends...
*/
smpboot_restore_warm_reset_vector();
/*
* Allow the user to impress friends.
*/
Dprintk("Before bogomips.\n");
for (cpu = 0; cpu < NR_CPUS; cpu++)
if (cpu_isset(cpu, cpu_callout_map))
bogosum += cpu_data[cpu].loops_per_jiffy;
printk(KERN_INFO
"Total of %d processors activated (%lu.%02lu BogoMIPS).\n",
cpucount+1,
bogosum/(500000/HZ),
(bogosum/(5000/HZ))%100);
Dprintk("Before bogocount - setting activated=1.\n");
if (smp_b_stepping)
printk(KERN_WARNING "WARNING: SMP operation may be unreliable with B stepping processors.\n");
/*
* Don't taint if we are running SMP kernel on a single non-MP
* approved Athlon
*/
if (tainted & TAINT_UNSAFE_SMP) {
if (cpucount)
printk (KERN_INFO "WARNING: This combination of AMD processors is not suitable for SMP.\n");
else
tainted &= ~TAINT_UNSAFE_SMP;
}
Dprintk("Boot done.\n");
/*
* construct cpu_sibling_map[], so that we can tell sibling CPUs
* efficiently.
*/
for (cpu = 0; cpu < NR_CPUS; cpu++)
cpus_clear(cpu_sibling_map[cpu]);
for (cpu = 0; cpu < NR_CPUS; cpu++) {
int siblings = 0;
int i;
if (!cpu_isset(cpu, cpu_callout_map))
continue;
if (smp_num_siblings > 1) {
for (i = 0; i < NR_CPUS; i++) {
if (!cpu_isset(i, cpu_callout_map))
continue;
if (phys_proc_id[cpu] == phys_proc_id[i]) {
siblings++;
cpu_set(i, cpu_sibling_map[cpu]);
}
}
} else {
siblings++;
cpu_set(cpu, cpu_sibling_map[cpu]);
}
if (siblings != smp_num_siblings)
printk(KERN_WARNING "WARNING: %d siblings found for CPU%d, should be %d\n", siblings, cpu, smp_num_siblings);
}
if (nmi_watchdog == NMI_LOCAL_APIC)
check_nmi_watchdog();
smpboot_setup_io_apic();
setup_boot_APIC_clock();
/*
* Synchronize the TSC with the AP
*/
if (cpu_has_tsc && cpucount && cpu_khz)
synchronize_tsc_bp();
}
int __init APIC_init_uniprocessor(void)
{
if (disable_apic) {
pr_info("Apic disabled\n");
return -1;
}
#ifdef CONFIG_X86_64
if (!cpu_has_apic) {
disable_apic = 1;
pr_info("Apic disabled by BIOS\n");
return -1;
}
#else
if (!smp_found_config && !cpu_has_apic)
return -1;
if (!cpu_has_apic &&
APIC_INTEGRATED(apic_version[boot_cpu_physical_apicid])) {
pr_err("BIOS bug, local APIC 0x%x not detected!...\n",
boot_cpu_physical_apicid);
return -1;
}
#endif
enable_IR_x2apic();
#ifdef CONFIG_X86_64
default_setup_apic_routing();
#endif
verify_local_APIC();
connect_bsp_APIC();
#ifdef CONFIG_X86_64
apic_write(APIC_ID, SET_APIC_ID(boot_cpu_physical_apicid));
#else
# ifdef CONFIG_CRASH_DUMP
boot_cpu_physical_apicid = read_apic_id();
# endif
#endif
physid_set_mask_of_physid(boot_cpu_physical_apicid, &phys_cpu_present_map);
setup_local_APIC();
#ifdef CONFIG_X86_IO_APIC
if (!skip_ioapic_setup && nr_ioapics)
enable_IO_APIC();
#endif
end_local_APIC_setup();
#ifdef CONFIG_X86_IO_APIC
if (smp_found_config && !skip_ioapic_setup && nr_ioapics)
setup_IO_APIC();
else {
nr_ioapics = 0;
localise_nmi_watchdog();
}
#else
localise_nmi_watchdog();
#endif
x86_init.timers.setup_percpu_clockev();
#ifdef CONFIG_X86_64
check_nmi_watchdog();
#endif
return 0;
}
static void __init smp_boot_cpus(unsigned int max_cpus)
{
unsigned apicid, cpu, bit, kicked;
nmi_watchdog_default();
/*
* Setup boot CPU information
*/
smp_store_cpu_info(0); /* Final full version of the data */
printk(KERN_INFO "CPU%d: ", 0);
print_cpu_info(&cpu_data[0]);
current_thread_info()->cpu = 0;
smp_tune_scheduling();
if (!physid_isset(hard_smp_processor_id(), phys_cpu_present_map)) {
printk("weird, boot CPU (#%d) not listed by the BIOS.\n",
hard_smp_processor_id());
physid_set(hard_smp_processor_id(), phys_cpu_present_map);
}
/*
* If we couldn't find an SMP configuration at boot time,
* get out of here now!
*/
if (!smp_found_config) {
printk(KERN_NOTICE "SMP motherboard not detected.\n");
io_apic_irqs = 0;
cpu_online_map = cpumask_of_cpu(0);
cpu_set(0, cpu_sibling_map[0]);
phys_cpu_present_map = physid_mask_of_physid(0);
if (APIC_init_uniprocessor())
printk(KERN_NOTICE "Local APIC not detected."
" Using dummy APIC emulation.\n");
goto smp_done;
}
/*
* Should not be necessary because the MP table should list the boot
* CPU too, but we do it for the sake of robustness anyway.
*/
if (!physid_isset(boot_cpu_id, phys_cpu_present_map)) {
printk(KERN_NOTICE "weird, boot CPU (#%d) not listed by the BIOS.\n",
boot_cpu_id);
physid_set(hard_smp_processor_id(), phys_cpu_present_map);
}
/*
* If we couldn't find a local APIC, then get out of here now!
*/
if (APIC_INTEGRATED(apic_version[boot_cpu_id]) && !cpu_has_apic) {
printk(KERN_ERR "BIOS bug, local APIC #%d not detected!...\n",
boot_cpu_id);
printk(KERN_ERR "... forcing use of dummy APIC emulation. (tell your hw vendor)\n");
io_apic_irqs = 0;
cpu_online_map = cpumask_of_cpu(0);
cpu_set(0, cpu_sibling_map[0]);
phys_cpu_present_map = physid_mask_of_physid(0);
disable_apic = 1;
goto smp_done;
}
verify_local_APIC();
/*
* If SMP should be disabled, then really disable it!
*/
if (!max_cpus) {
smp_found_config = 0;
printk(KERN_INFO "SMP mode deactivated, forcing use of dummy APIC emulation.\n");
io_apic_irqs = 0;
cpu_online_map = cpumask_of_cpu(0);
cpu_set(0, cpu_sibling_map[0]);
phys_cpu_present_map = physid_mask_of_physid(0);
disable_apic = 1;
goto smp_done;
}
connect_bsp_APIC();
setup_local_APIC();
if (GET_APIC_ID(apic_read(APIC_ID)) != boot_cpu_id)
BUG();
x86_cpu_to_apicid[0] = boot_cpu_id;
/*
* Now scan the CPU present map and fire up the other CPUs.
*/
Dprintk("CPU present map: %lx\n", physids_coerce(phys_cpu_present_map));
kicked = 1;
for (bit = 0; kicked < NR_CPUS && bit < MAX_APICS; bit++) {
apicid = cpu_present_to_apicid(bit);
/*
* Don't even attempt to start the boot CPU!
*/
if (apicid == boot_cpu_id || (apicid == BAD_APICID))
continue;
if (!physid_isset(apicid, phys_cpu_present_map))
continue;
if ((max_cpus >= 0) && (max_cpus <= cpucount+1))
continue;
do_boot_cpu(apicid);
++kicked;
}
/*
* Cleanup possible dangling ends...
*/
{
/*
* Install writable page 0 entry to set BIOS data area.
*/
local_flush_tlb();
/*
* Paranoid: Set warm reset code and vector here back
* to default values.
*/
CMOS_WRITE(0, 0xf);
*((volatile int *) phys_to_virt(0x467)) = 0;
}
/*
* Allow the user to impress friends.
*/
Dprintk("Before bogomips.\n");
if (!cpucount) {
printk(KERN_INFO "Only one processor found.\n");
} else {
unsigned long bogosum = 0;
for (cpu = 0; cpu < NR_CPUS; cpu++)
if (cpu_isset(cpu, cpu_callout_map))
bogosum += cpu_data[cpu].loops_per_jiffy;
printk(KERN_INFO "Total of %d processors activated (%lu.%02lu BogoMIPS).\n",
cpucount+1,
bogosum/(500000/HZ),
(bogosum/(5000/HZ))%100);
Dprintk("Before bogocount - setting activated=1.\n");
}
/*
* Construct cpu_sibling_map[], so that we can tell the
* sibling CPU efficiently.
*/
for (cpu = 0; cpu < NR_CPUS; cpu++)
cpus_clear(cpu_sibling_map[cpu]);
for (cpu = 0; cpu < NR_CPUS; cpu++) {
int siblings = 0;
int i;
if (!cpu_isset(cpu, cpu_callout_map))
continue;
if (smp_num_siblings > 1) {
for (i = 0; i < NR_CPUS; i++) {
if (!cpu_isset(i, cpu_callout_map))
continue;
if (phys_proc_id[cpu] == phys_proc_id[i]) {
siblings++;
cpu_set(i, cpu_sibling_map[cpu]);
}
}
} else {
siblings++;
cpu_set(cpu, cpu_sibling_map[cpu]);
}
if (siblings != smp_num_siblings) {
printk(KERN_WARNING
"WARNING: %d siblings found for CPU%d, should be %d\n",
siblings, cpu, smp_num_siblings);
smp_num_siblings = siblings;
}
}
Dprintk("Boot done.\n");
/*
* Here we can be sure that there is an IO-APIC in the system. Let's
* go and set it up:
*/
if (!skip_ioapic_setup && nr_ioapics)
setup_IO_APIC();
else
nr_ioapics = 0;
setup_boot_APIC_clock();
/*
* Synchronize the TSC with the AP
*/
if (cpu_has_tsc && cpucount)
synchronize_tsc_bp();
smp_done:
time_init_smp();
}
