int cx231xx_reset_analog_tuner(struct cx231xx *dev)
{
int status = 0;
if ((dev->dvb != NULL) && (dev->dvb->frontend != NULL)) {
struct dvb_tuner_ops *dops = &dev->dvb->frontend->ops.tuner_ops;
if (dops->init != NULL && !dev->xc_fw_load_done) {
cx231xx_info("Reloading firmware for XC5000\n");
status = dops->init(dev->dvb->frontend);
if (status == 0) {
dev->xc_fw_load_done = 1;
cx231xx_info
("XC5000 firmware download completed\n");
} else {
dev->xc_fw_load_done = 0;
cx231xx_info
("XC5000 firmware download failed !!!\n");
}
}
}
return status;
}
/* Since cx231xx_pre_card_setup() requires a proper dev->model,
* this won't work for boards with generic PCI IDs
*/
void cx231xx_pre_card_setup(struct cx231xx *dev)
{
cx231xx_set_model(dev);
cx231xx_info("Identified as %s (card=%d)\n",
dev->board.name, dev->model);
/* set the direction for GPIO pins */
if (dev->board.tuner_gpio) {
cx231xx_set_gpio_direction(dev, dev->board.tuner_gpio->bit, 1);
cx231xx_set_gpio_value(dev, dev->board.tuner_gpio->bit, 1);
cx231xx_set_gpio_direction(dev, dev->board.tuner_sif_gpio, 1);
/* request some modules if any required */
/* reset the Tuner */
cx231xx_gpio_set(dev, dev->board.tuner_gpio);
}
/* set the mode to Analog mode initially */
cx231xx_set_mode(dev, CX231XX_ANALOG_MODE);
/* Unlock device */
/* cx231xx_set_mode(dev, CX231XX_SUSPEND); */
}
int cx231xx_tuner_callback(void *ptr, int component, int command, int arg)
{
int rc = 0;
struct cx231xx *dev = ptr;
if (dev->tuner_type == TUNER_XC5000) {
if (command == XC5000_TUNER_RESET) {
cx231xx_info
("Tuner CB: RESET: cmd %d : tuner type %d \n",
command, dev->tuner_type);
cx231xx_set_gpio_value(dev, dev->board.tuner_gpio->bit,
1);
msleep(10);
cx231xx_set_gpio_value(dev, dev->board.tuner_gpio->bit,
0);
msleep(330);
cx231xx_set_gpio_value(dev, dev->board.tuner_gpio->bit,
1);
msleep(10);
}
} else if (dev->tuner_type == TUNER_NXP_TDA18271) {
switch (command) {
case TDA18271_CALLBACK_CMD_AGC_ENABLE:
if (dev->model == CX231XX_BOARD_PV_PLAYTV_USB_HYBRID)
rc = cx231xx_set_agc_analog_digital_mux_select(dev, arg);
break;
default:
rc = -EINVAL;
break;
}
}
return rc;
}
int cx231xx_set_analog_freq(struct cx231xx *dev, u32 freq)
{
int status = 0;
if ((dev->dvb != NULL) && (dev->dvb->frontend != NULL)) {
struct dvb_tuner_ops *dops = &dev->dvb->frontend->ops.tuner_ops;
if (dops->set_analog_params != NULL) {
struct analog_parameters params;
params.frequency = freq;
params.std = dev->norm;
params.mode = 0; /* 0- Air; 1 - cable */
/*params.audmode = ; */
/* Set the analog parameters to set the frequency */
cx231xx_info("Setting Frequency for XC5000\n");
dops->set_analog_params(dev->dvb->frontend, ¶ms);
}
}
return status;
}
void cx231xx_do_i2c_scan(struct cx231xx *dev, struct i2c_client *c)
{
unsigned char buf;
int i, rc;
cx231xx_info(": Checking for I2C devices ..\n");
for (i = 0; i < 128; i++) {
c->addr = i;
rc = i2c_master_recv(c, &buf, 0);
if (rc < 0)
continue;
cx231xx_info("%s: i2c scan: found device @ 0x%x [%s]\n",
dev->name, i << 1,
i2c_devs[i] ? i2c_devs[i] : "???");
}
cx231xx_info(": Completed Checking for I2C devices.\n");
}
static void cx231xx_config_tuner(struct cx231xx *dev)
{
struct tuner_setup tun_setup;
struct v4l2_frequency f;
if (dev->tuner_type == TUNER_ABSENT)
return;
tun_setup.mode_mask = T_ANALOG_TV | T_RADIO;
tun_setup.type = dev->tuner_type;
tun_setup.addr = dev->tuner_addr;
tun_setup.tuner_callback = cx231xx_tuner_callback;
tuner_call(dev, tuner, s_type_addr, &tun_setup);
#if 0
if (tun_setup.type == TUNER_XC5000) {
static struct xc2028_ctrl ctrl = {
.fname = XC5000_DEFAULT_FIRMWARE,
.max_len = 64,
.demod = 0;
};
struct v4l2_priv_tun_config cfg = {
.tuner = dev->tuner_type,
.priv = &ctrl,
};
tuner_call(dev, tuner, s_config, &cfg);
}
#endif
/* configure tuner */
f.tuner = 0;
f.type = V4L2_TUNER_ANALOG_TV;
f.frequency = 9076; /* just a magic number */
dev->ctl_freq = f.frequency;
call_all(dev, tuner, s_frequency, &f);
}
void cx231xx_card_setup(struct cx231xx *dev)
{
cx231xx_set_model(dev);
dev->tuner_type = cx231xx_boards[dev->model].tuner_type;
if (cx231xx_boards[dev->model].tuner_addr)
dev->tuner_addr = cx231xx_boards[dev->model].tuner_addr;
/* request some modules */
if (dev->board.decoder == CX231XX_AVDECODER) {
dev->sd_cx25840 = v4l2_i2c_new_subdev(&dev->v4l2_dev,
&dev->i2c_bus[0].i2c_adap,
"cx25840", 0x88 >> 1, NULL);
if (dev->sd_cx25840 == NULL)
cx231xx_info("cx25840 subdev registration failure\n");
cx25840_call(dev, core, load_fw);
}
/*
* Stop and Deallocate URBs
*/
void cx231xx_uninit_vbi_isoc(struct cx231xx *dev)
{
struct urb *urb;
int i;
cx231xx_info(DRIVER_NAME "cx231xx: called cx231xx_uninit_vbi_isoc\n");
dev->vbi_mode.bulk_ctl.nfields = -1;
for (i = 0; i < dev->vbi_mode.bulk_ctl.num_bufs; i++) {
urb = dev->vbi_mode.bulk_ctl.urb[i];
if (urb) {
if (!irqs_disabled())
usb_kill_urb(urb);
else
usb_unlink_urb(urb);
if (dev->vbi_mode.bulk_ctl.transfer_buffer[i]) {
kfree(dev->vbi_mode.bulk_ctl.
transfer_buffer[i]);
dev->vbi_mode.bulk_ctl.transfer_buffer[i] =
NULL;
}
usb_free_urb(urb);
dev->vbi_mode.bulk_ctl.urb[i] = NULL;
}
dev->vbi_mode.bulk_ctl.transfer_buffer[i] = NULL;
}
kfree(dev->vbi_mode.bulk_ctl.urb);
kfree(dev->vbi_mode.bulk_ctl.transfer_buffer);
dev->vbi_mode.bulk_ctl.urb = NULL;
dev->vbi_mode.bulk_ctl.transfer_buffer = NULL;
dev->vbi_mode.bulk_ctl.num_bufs = 0;
cx231xx_capture_start(dev, 0, Vbi);
}
int cx231xx_tuner_callback(void *ptr, int component, int command, int arg)
{
int rc = 0;
struct cx231xx *dev = ptr;
if (dev->tuner_type == TUNER_XC5000) {
if (command == XC5000_TUNER_RESET) {
cx231xx_info
("Tuner CB: RESET: cmd %d : tuner type %d \n",
command, dev->tuner_type);
cx231xx_set_gpio_value(dev, dev->board.tuner_gpio->bit,
1);
msleep(10);
cx231xx_set_gpio_value(dev, dev->board.tuner_gpio->bit,
0);
msleep(330);
cx231xx_set_gpio_value(dev, dev->board.tuner_gpio->bit,
1);
msleep(10);
}
}
return rc;
}
/*
* Allocate URBs and start IRQ
*/
int cx231xx_init_vbi_isoc(struct cx231xx *dev, int max_packets,
int num_bufs, int max_pkt_size,
int (*bulk_copy) (struct cx231xx *dev,
struct urb *urb))
{
struct cx231xx_dmaqueue *dma_q = &dev->vbi_mode.vidq;
int i;
int sb_size, pipe;
struct urb *urb;
int rc;
cx231xx_info(DRIVER_NAME "cx231xx: called cx231xx_prepare_isoc\n");
/* De-allocates all pending stuff */
cx231xx_uninit_vbi_isoc(dev);
/* clear if any halt */
usb_clear_halt(dev->udev,
usb_rcvbulkpipe(dev->udev,
dev->vbi_mode.end_point_addr));
dev->vbi_mode.bulk_ctl.bulk_copy = bulk_copy;
dev->vbi_mode.bulk_ctl.num_bufs = num_bufs;
dma_q->pos = 0;
dma_q->is_partial_line = 0;
dma_q->last_sav = 0;
dma_q->current_field = -1;
dma_q->bytes_left_in_line = dev->width << 1;
dma_q->lines_per_field = ((dev->norm & V4L2_STD_625_50) ?
PAL_VBI_LINES : NTSC_VBI_LINES);
dma_q->lines_completed = 0;
for (i = 0; i < 8; i++)
dma_q->partial_buf[i] = 0;
dev->vbi_mode.bulk_ctl.urb = kzalloc(sizeof(void *) * num_bufs,
GFP_KERNEL);
if (!dev->vbi_mode.bulk_ctl.urb) {
cx231xx_errdev("cannot alloc memory for usb buffers\n");
return -ENOMEM;
}
dev->vbi_mode.bulk_ctl.transfer_buffer =
kzalloc(sizeof(void *) * num_bufs, GFP_KERNEL);
if (!dev->vbi_mode.bulk_ctl.transfer_buffer) {
cx231xx_errdev("cannot allocate memory for usbtransfer\n");
kfree(dev->vbi_mode.bulk_ctl.urb);
return -ENOMEM;
}
dev->vbi_mode.bulk_ctl.max_pkt_size = max_pkt_size;
dev->vbi_mode.bulk_ctl.buf = NULL;
sb_size = max_packets * dev->vbi_mode.bulk_ctl.max_pkt_size;
/* allocate urbs and transfer buffers */
for (i = 0; i < dev->vbi_mode.bulk_ctl.num_bufs; i++) {
urb = usb_alloc_urb(0, GFP_KERNEL);
if (!urb) {
cx231xx_err(DRIVER_NAME
": cannot alloc bulk_ctl.urb %i\n", i);
cx231xx_uninit_vbi_isoc(dev);
return -ENOMEM;
}
dev->vbi_mode.bulk_ctl.urb[i] = urb;
urb->transfer_flags = 0;
dev->vbi_mode.bulk_ctl.transfer_buffer[i] =
kzalloc(sb_size, GFP_KERNEL);
if (!dev->vbi_mode.bulk_ctl.transfer_buffer[i]) {
cx231xx_err(DRIVER_NAME
": unable to allocate %i bytes for transfer"
" buffer %i%s\n", sb_size, i,
in_interrupt() ? " while in int" : "");
cx231xx_uninit_vbi_isoc(dev);
return -ENOMEM;
}
pipe = usb_rcvbulkpipe(dev->udev, dev->vbi_mode.end_point_addr);
usb_fill_bulk_urb(urb, dev->udev, pipe,
dev->vbi_mode.bulk_ctl.transfer_buffer[i],
sb_size, cx231xx_irq_vbi_callback, dma_q);
}
init_waitqueue_head(&dma_q->wq);
/* submit urbs and enables IRQ */
for (i = 0; i < dev->vbi_mode.bulk_ctl.num_bufs; i++) {
rc = usb_submit_urb(dev->vbi_mode.bulk_ctl.urb[i], GFP_ATOMIC);
if (rc) {
cx231xx_err(DRIVER_NAME
": submit of urb %i failed (error=%i)\n", i,
rc);
cx231xx_uninit_vbi_isoc(dev);
return rc;
}
}
cx231xx_capture_start(dev, 1, Vbi);
return 0;
}
u32 initialize_cx231xx(struct cx231xx *dev)
{
u32 config_info = 0;
struct pcb_config *p_pcb_info;
u8 usb_speed = 1;
u8 data[4] = { 0, 0, 0, 0 };
u32 ts1_source = 0;
u32 ts2_source = 0;
u32 analog_source = 0;
u8 _current_scenario_idx = 0xff;
ts1_source = SOURCE_TS_BDA;
ts2_source = SOURCE_TS_BDA;
cx231xx_read_ctrl_reg(dev, VRT_GET_REGISTER, BOARD_CFG_STAT, data, 4);
config_info = *((u32 *) data);
usb_speed = (u8) (config_info & 0x1);
if (config_info & BUS_POWER) {
switch (config_info & BUSPOWER_MASK) {
case TS1_PORT | BUS_POWER:
cx231xx_Scenario[INDEX_BUSPOWER_DIGITAL_ONLY].speed =
usb_speed;
p_pcb_info =
&cx231xx_Scenario[INDEX_BUSPOWER_DIGITAL_ONLY];
_current_scenario_idx = INDEX_BUSPOWER_DIGITAL_ONLY;
break;
case AVDEC_ENABLE | BUS_POWER:
cx231xx_Scenario[INDEX_BUSPOWER_ANALOG_ONLY].speed =
usb_speed;
p_pcb_info =
&cx231xx_Scenario[INDEX_BUSPOWER_ANALOG_ONLY];
_current_scenario_idx = INDEX_BUSPOWER_ANALOG_ONLY;
break;
case AVDEC_ENABLE | BUS_POWER | TS1_PORT:
cx231xx_Scenario[INDEX_BUSPOWER_DIF_ONLY].speed =
usb_speed;
p_pcb_info = &cx231xx_Scenario[INDEX_BUSPOWER_DIF_ONLY];
_current_scenario_idx = INDEX_BUSPOWER_DIF_ONLY;
break;
default:
cx231xx_info("bad config in buspower!!!!\n");
cx231xx_info("config_info=%x\n",
(config_info & BUSPOWER_MASK));
return 1;
}
} else {
switch (config_info & SELFPOWER_MASK) {
case TS1_PORT | SELF_POWER:
cx231xx_Scenario[INDEX_SELFPOWER_DIGITAL_ONLY].speed =
usb_speed;
p_pcb_info =
&cx231xx_Scenario[INDEX_SELFPOWER_DIGITAL_ONLY];
_current_scenario_idx = INDEX_SELFPOWER_DIGITAL_ONLY;
break;
case TS1_TS2_PORT | SELF_POWER:
cx231xx_Scenario[INDEX_SELFPOWER_DUAL_DIGITAL].speed =
usb_speed;
cx231xx_Scenario[INDEX_SELFPOWER_DUAL_DIGITAL].
ts2_source = ts2_source;
p_pcb_info =
&cx231xx_Scenario[INDEX_SELFPOWER_DUAL_DIGITAL];
_current_scenario_idx = INDEX_SELFPOWER_DUAL_DIGITAL;
break;
case AVDEC_ENABLE | SELF_POWER:
cx231xx_Scenario[INDEX_SELFPOWER_ANALOG_ONLY].speed =
usb_speed;
cx231xx_Scenario[INDEX_SELFPOWER_ANALOG_ONLY].
analog_source = analog_source;
p_pcb_info =
&cx231xx_Scenario[INDEX_SELFPOWER_ANALOG_ONLY];
_current_scenario_idx = INDEX_SELFPOWER_ANALOG_ONLY;
break;
case AVDEC_ENABLE | TS1_PORT | SELF_POWER:
cx231xx_Scenario[INDEX_SELFPOWER_DUAL].speed =
usb_speed;
cx231xx_Scenario[INDEX_SELFPOWER_DUAL].ts1_source =
ts1_source;
cx231xx_Scenario[INDEX_SELFPOWER_DUAL].analog_source =
analog_source;
p_pcb_info = &cx231xx_Scenario[INDEX_SELFPOWER_DUAL];
_current_scenario_idx = INDEX_SELFPOWER_DUAL;
break;
case AVDEC_ENABLE | TS1_TS2_PORT | SELF_POWER:
cx231xx_Scenario[INDEX_SELFPOWER_TRIPLE].speed =
usb_speed;
cx231xx_Scenario[INDEX_SELFPOWER_TRIPLE].ts1_source =
ts1_source;
cx231xx_Scenario[INDEX_SELFPOWER_TRIPLE].ts2_source =
ts2_source;
cx231xx_Scenario[INDEX_SELFPOWER_TRIPLE].analog_source =
analog_source;
p_pcb_info = &cx231xx_Scenario[INDEX_SELFPOWER_TRIPLE];
_current_scenario_idx = INDEX_SELFPOWER_TRIPLE;
break;
case AVDEC_ENABLE | TS1VIP_TS2_PORT | SELF_POWER:
cx231xx_Scenario[INDEX_SELFPOWER_COMPRESSOR].speed =
usb_speed;
cx231xx_Scenario[INDEX_SELFPOWER_COMPRESSOR].
analog_source = analog_source;
p_pcb_info =
&cx231xx_Scenario[INDEX_SELFPOWER_COMPRESSOR];
_current_scenario_idx = INDEX_SELFPOWER_COMPRESSOR;
break;
default:
cx231xx_info("bad senario!!!!!\n");
cx231xx_info("config_info=%x\n",
(config_info & SELFPOWER_MASK));
return 1;
}
}
dev->current_scenario_idx = _current_scenario_idx;
memcpy(&dev->current_pcb_config, p_pcb_info,
sizeof(struct pcb_config));
if (pcb_debug) {
cx231xx_info("SC(0x00) register = 0x%x\n", config_info);
cx231xx_info("scenario %d\n",
(dev->current_pcb_config.index) + 1);
cx231xx_info("type=%x\n", dev->current_pcb_config.type);
cx231xx_info("mode=%x\n", dev->current_pcb_config.mode);
cx231xx_info("speed=%x\n", dev->current_pcb_config.speed);
cx231xx_info("ts1_source=%x\n",
dev->current_pcb_config.ts1_source);
cx231xx_info("ts2_source=%x\n",
dev->current_pcb_config.ts2_source);
cx231xx_info("analog_source=%x\n",
dev->current_pcb_config.analog_source);
}
return 0;
}
int initialize_cx231xx(struct cx231xx *dev)
{
int retval;
u32 config_info = 0;
struct pcb_config *p_pcb_info;
u8 usb_speed = 1; /* from register,1--HS, 0--FS */
u8 data[4] = { 0, 0, 0, 0 };
u32 ts1_source = 0;
u32 ts2_source = 0;
u32 analog_source = 0;
u8 _current_scenario_idx = 0xff;
ts1_source = SOURCE_TS_BDA;
ts2_source = SOURCE_TS_BDA;
/* read board config register to find out which
pcb config it is related to */
retval = cx231xx_read_ctrl_reg(dev, VRT_GET_REGISTER, BOARD_CFG_STAT,
data, 4);
if (retval < 0)
return retval;
config_info = le32_to_cpu(*((__le32 *)data));
usb_speed = (u8) (config_info & 0x1);
/* Verify this device belongs to Bus power or Self power device */
if (config_info & BUS_POWER) { /* bus-power */
switch (config_info & BUSPOWER_MASK) {
case TS1_PORT | BUS_POWER:
cx231xx_Scenario[INDEX_BUSPOWER_DIGITAL_ONLY].speed =
usb_speed;
p_pcb_info =
&cx231xx_Scenario[INDEX_BUSPOWER_DIGITAL_ONLY];
_current_scenario_idx = INDEX_BUSPOWER_DIGITAL_ONLY;
break;
case AVDEC_ENABLE | BUS_POWER:
cx231xx_Scenario[INDEX_BUSPOWER_ANALOG_ONLY].speed =
usb_speed;
p_pcb_info =
&cx231xx_Scenario[INDEX_BUSPOWER_ANALOG_ONLY];
_current_scenario_idx = INDEX_BUSPOWER_ANALOG_ONLY;
break;
case AVDEC_ENABLE | BUS_POWER | TS1_PORT:
cx231xx_Scenario[INDEX_BUSPOWER_DIF_ONLY].speed =
usb_speed;
p_pcb_info = &cx231xx_Scenario[INDEX_BUSPOWER_DIF_ONLY];
_current_scenario_idx = INDEX_BUSPOWER_DIF_ONLY;
break;
default:
cx231xx_info("bad config in buspower!!!!\n");
cx231xx_info("config_info=%x\n",
(config_info & BUSPOWER_MASK));
return 1;
}
} else { /* self-power */
switch (config_info & SELFPOWER_MASK) {
case TS1_PORT | SELF_POWER:
cx231xx_Scenario[INDEX_SELFPOWER_DIGITAL_ONLY].speed =
usb_speed;
p_pcb_info =
&cx231xx_Scenario[INDEX_SELFPOWER_DIGITAL_ONLY];
_current_scenario_idx = INDEX_SELFPOWER_DIGITAL_ONLY;
break;
case TS1_TS2_PORT | SELF_POWER:
cx231xx_Scenario[INDEX_SELFPOWER_DUAL_DIGITAL].speed =
usb_speed;
cx231xx_Scenario[INDEX_SELFPOWER_DUAL_DIGITAL].
ts2_source = ts2_source;
p_pcb_info =
&cx231xx_Scenario[INDEX_SELFPOWER_DUAL_DIGITAL];
_current_scenario_idx = INDEX_SELFPOWER_DUAL_DIGITAL;
break;
case AVDEC_ENABLE | SELF_POWER:
cx231xx_Scenario[INDEX_SELFPOWER_ANALOG_ONLY].speed =
usb_speed;
cx231xx_Scenario[INDEX_SELFPOWER_ANALOG_ONLY].
analog_source = analog_source;
p_pcb_info =
&cx231xx_Scenario[INDEX_SELFPOWER_ANALOG_ONLY];
_current_scenario_idx = INDEX_SELFPOWER_ANALOG_ONLY;
break;
case AVDEC_ENABLE | TS1_PORT | SELF_POWER:
cx231xx_Scenario[INDEX_SELFPOWER_DUAL].speed =
usb_speed;
cx231xx_Scenario[INDEX_SELFPOWER_DUAL].ts1_source =
ts1_source;
cx231xx_Scenario[INDEX_SELFPOWER_DUAL].analog_source =
analog_source;
p_pcb_info = &cx231xx_Scenario[INDEX_SELFPOWER_DUAL];
_current_scenario_idx = INDEX_SELFPOWER_DUAL;
break;
case AVDEC_ENABLE | TS1_TS2_PORT | SELF_POWER:
cx231xx_Scenario[INDEX_SELFPOWER_TRIPLE].speed =
usb_speed;
cx231xx_Scenario[INDEX_SELFPOWER_TRIPLE].ts1_source =
ts1_source;
cx231xx_Scenario[INDEX_SELFPOWER_TRIPLE].ts2_source =
ts2_source;
cx231xx_Scenario[INDEX_SELFPOWER_TRIPLE].analog_source =
analog_source;
p_pcb_info = &cx231xx_Scenario[INDEX_SELFPOWER_TRIPLE];
_current_scenario_idx = INDEX_SELFPOWER_TRIPLE;
break;
case AVDEC_ENABLE | TS1VIP_TS2_PORT | SELF_POWER:
cx231xx_Scenario[INDEX_SELFPOWER_COMPRESSOR].speed =
usb_speed;
cx231xx_Scenario[INDEX_SELFPOWER_COMPRESSOR].
analog_source = analog_source;
p_pcb_info =
&cx231xx_Scenario[INDEX_SELFPOWER_COMPRESSOR];
_current_scenario_idx = INDEX_SELFPOWER_COMPRESSOR;
break;
default:
cx231xx_info("bad senario!!!!!\n");
cx231xx_info("config_info=%x\n",
(config_info & SELFPOWER_MASK));
return -ENODEV;
}
}
dev->current_scenario_idx = _current_scenario_idx;
memcpy(&dev->current_pcb_config, p_pcb_info,
sizeof(struct pcb_config));
if (pcb_debug) {
cx231xx_info("SC(0x00) register = 0x%x\n", config_info);
cx231xx_info("scenario %d\n",
(dev->current_pcb_config.index) + 1);
cx231xx_info("type=%x\n", dev->current_pcb_config.type);
cx231xx_info("mode=%x\n", dev->current_pcb_config.mode);
cx231xx_info("speed=%x\n", dev->current_pcb_config.speed);
cx231xx_info("ts1_source=%x\n",
dev->current_pcb_config.ts1_source);
cx231xx_info("ts2_source=%x\n",
dev->current_pcb_config.ts2_source);
cx231xx_info("analog_source=%x\n",
dev->current_pcb_config.analog_source);
}
return 0;
}
