/*************************************************************************
*
* initdram -- 440EPx's DDR controller is a DENALI Core
*
************************************************************************/
phys_size_t initdram (int board_type)
{
#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_SYS_RAMBOOT)) || \
defined(CONFIG_NAND_SPL)
ulong speed = get_bus_freq(0);
mtsdram(DDR0_02, 0x00000000);
mtsdram(DDR0_00, 0x0000190A);
mtsdram(DDR0_01, 0x01000000);
mtsdram(DDR0_03, 0x02030602);
mtsdram(DDR0_04, 0x0A020200);
mtsdram(DDR0_05, 0x02020308);
mtsdram(DDR0_06, 0x0102C812);
mtsdram(DDR0_07, 0x000D0100);
mtsdram(DDR0_08, 0x02430001);
mtsdram(DDR0_09, 0x00011D5F);
mtsdram(DDR0_10, 0x00000100);
mtsdram(DDR0_11, 0x0027C800);
mtsdram(DDR0_12, 0x00000003);
mtsdram(DDR0_14, 0x00000000);
mtsdram(DDR0_17, 0x19000000);
mtsdram(DDR0_18, 0x19191919);
mtsdram(DDR0_19, 0x19191919);
mtsdram(DDR0_20, 0x0B0B0B0B);
mtsdram(DDR0_21, 0x0B0B0B0B);
mtsdram(DDR0_22, 0x00267F0B);
mtsdram(DDR0_23, 0x00000000);
mtsdram(DDR0_24, 0x01010002);
if (speed > 133333334)
mtsdram(DDR0_26, 0x5B26050C);
else
mtsdram(DDR0_26, 0x5B260408);
mtsdram(DDR0_27, 0x0000682B);
mtsdram(DDR0_28, 0x00000000);
mtsdram(DDR0_31, 0x00000000);
mtsdram(DDR0_42, 0x01000006);
mtsdram(DDR0_43, 0x030A0200);
mtsdram(DDR0_44, 0x00000003);
mtsdram(DDR0_02, 0x00000001);
denali_wait_for_dlllock();
#endif /* #ifndef CONFIG_NAND_U_BOOT */
#ifdef CONFIG_DDR_DATA_EYE
/* -----------------------------------------------------------+
* Perform data eye search if requested.
* ----------------------------------------------------------*/
denali_core_search_data_eye();
#endif
/*
* Clear possible errors resulting from data-eye-search.
* If not done, then we could get an interrupt later on when
* exceptions are enabled.
*/
set_mcsr(get_mcsr());
return (CONFIG_SYS_MBYTES_SDRAM << 20);
}
/*************************************************************************
*
* initdram -- 440EPx's DDR controller is a DENALI Core
*
************************************************************************/
long int initdram (int board_type)
{
#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
#if !defined(CONFIG_NAND_SPL)
ulong speed = get_bus_freq(0);
#else
ulong speed = 133333333; /* 133MHz is on the safe side */
#endif
mtsdram(DDR0_02, 0x00000000);
mtsdram(DDR0_00, 0x0000190A);
mtsdram(DDR0_01, 0x01000000);
mtsdram(DDR0_03, 0x02030602);
mtsdram(DDR0_04, 0x0A020200);
mtsdram(DDR0_05, 0x02020308);
mtsdram(DDR0_06, 0x0102C812);
mtsdram(DDR0_07, 0x000D0100);
mtsdram(DDR0_08, 0x02430001);
mtsdram(DDR0_09, 0x00011D5F);
mtsdram(DDR0_10, 0x00000300);
mtsdram(DDR0_11, 0x0027C800);
mtsdram(DDR0_12, 0x00000003);
mtsdram(DDR0_14, 0x00000000);
mtsdram(DDR0_17, 0x19000000);
mtsdram(DDR0_18, 0x19191919);
mtsdram(DDR0_19, 0x19191919);
mtsdram(DDR0_20, 0x0B0B0B0B);
mtsdram(DDR0_21, 0x0B0B0B0B);
mtsdram(DDR0_22, 0x00267F0B);
mtsdram(DDR0_23, 0x00000000);
mtsdram(DDR0_24, 0x01010002);
if (speed > 133333334)
mtsdram(DDR0_26, 0x5B26050C);
else
mtsdram(DDR0_26, 0x5B260408);
mtsdram(DDR0_27, 0x0000682B);
mtsdram(DDR0_28, 0x00000000);
mtsdram(DDR0_31, 0x00000000);
mtsdram(DDR0_42, 0x01000006);
mtsdram(DDR0_43, 0x030A0200);
mtsdram(DDR0_44, 0x00000003);
mtsdram(DDR0_02, 0x00000001);
wait_for_dlllock();
#endif /* #ifndef CONFIG_NAND_U_BOOT */
#ifdef CONFIG_DDR_DATA_EYE
/* -----------------------------------------------------------+
* Perform data eye search if requested.
* ----------------------------------------------------------*/
denali_core_search_data_eye(CFG_MBYTES_SDRAM << 20);
#endif
return (CFG_MBYTES_SDRAM << 20);
}
/*-----------------------------------------------------------------------------
* Function: initdram
* Description: Configures SDRAM memory banks for DDR operation.
* Auto Memory Configuration option reads the DDR SDRAM EEPROMs
* via the IIC bus and then configures the DDR SDRAM memory
* banks appropriately. If Auto Memory Configuration is
* not used, it is assumed that no DIMM is plugged
*-----------------------------------------------------------------------------*/
phys_size_t initdram(int board_type)
{
unsigned char const iic0_dimm_addr[] = SPD_EEPROM_ADDRESS;
unsigned long dimm_ranks[MAXDIMMS];
unsigned long ranks;
unsigned long rows;
unsigned long banks;
unsigned long cols;
unsigned long width;
unsigned long const sdram_freq = get_bus_freq(0);
unsigned long const num_dimm_banks = sizeof(iic0_dimm_addr); /* on board dimm banks */
unsigned long cas_latency = 0; /* to quiet initialization warning */
unsigned long dram_size;
debug("\nEntering initdram()\n");
/*------------------------------------------------------------------
* Stop the DDR-SDRAM controller.
*-----------------------------------------------------------------*/
mtsdram(DDR0_02, DDR0_02_START_ENCODE(0));
/*
* Make sure I2C controller is initialized
* before continuing.
*/
/* switch to correct I2C bus */
I2C_SET_BUS(CONFIG_SYS_SPD_BUS_NUM);
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
/*------------------------------------------------------------------
* Clear out the serial presence detect buffers.
* Perform IIC reads from the dimm. Fill in the spds.
* Check to see if the dimm slots are populated
*-----------------------------------------------------------------*/
get_spd_info(dimm_ranks, &ranks, iic0_dimm_addr, num_dimm_banks);
/*------------------------------------------------------------------
* Check the frequency supported for the dimms plugged.
*-----------------------------------------------------------------*/
check_frequency(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq);
/*------------------------------------------------------------------
* Check and get size information.
*-----------------------------------------------------------------*/
get_dimm_size(dimm_ranks, iic0_dimm_addr, num_dimm_banks, &rows, &banks,
&cols, &width);
/*------------------------------------------------------------------
* Check the voltage type for the dimms plugged.
*-----------------------------------------------------------------*/
check_voltage_type(dimm_ranks, iic0_dimm_addr, num_dimm_banks);
/*------------------------------------------------------------------
* Program registers for SDRAM controller.
*-----------------------------------------------------------------*/
mtsdram(DDR0_00, DDR0_00_DLL_INCREMENT_ENCODE(0x19) |
DDR0_00_DLL_START_POINT_DECODE(0x0A));
mtsdram(DDR0_01, DDR0_01_PLB0_DB_CS_LOWER_ENCODE(0x01) |
DDR0_01_PLB0_DB_CS_UPPER_ENCODE(0x00) |
DDR0_01_INT_MASK_ENCODE(0xFF));
program_ddr0_03(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq,
rows, &cas_latency);
program_ddr0_04(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq);
program_ddr0_05(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq);
program_ddr0_06(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq);
/*
* TODO: tFAW not found in SPD. Value of 13 taken from Sequoia
* board SDRAM, but may be overly conservative.
*/
mtsdram(DDR0_07, DDR0_07_NO_CMD_INIT_ENCODE(0) |
DDR0_07_TFAW_ENCODE(13) |
DDR0_07_AUTO_REFRESH_MODE_ENCODE(1) |
DDR0_07_AREFRESH_ENCODE(0));
mtsdram(DDR0_08, DDR0_08_WRLAT_ENCODE(cas_latency - 1) |
DDR0_08_TCPD_ENCODE(200) | DDR0_08_DQS_N_EN_ENCODE(0) |
DDR0_08_DDRII_ENCODE(1));
mtsdram(DDR0_09, DDR0_09_OCD_ADJUST_PDN_CS_0_ENCODE(0x00) |
DDR0_09_RTT_0_ENCODE(0x1) |
DDR0_09_WR_DQS_SHIFT_BYPASS_ENCODE(0x1D) |
DDR0_09_WR_DQS_SHIFT_ENCODE(DQS_OUT_SHIFT - 0x20));
program_ddr0_10(dimm_ranks, ranks);
program_ddr0_11(sdram_freq);
mtsdram(DDR0_12, DDR0_12_TCKE_ENCODE(3));
mtsdram(DDR0_14, DDR0_14_DLL_BYPASS_MODE_ENCODE(0) |
DDR0_14_REDUC_ENCODE(width <= 40 ? 1 : 0) |
DDR0_14_REG_DIMM_ENABLE_ENCODE(0));
mtsdram(DDR0_17, DDR0_17_DLL_DQS_DELAY_0_ENCODE(DLL_DQS_DELAY));
mtsdram(DDR0_18, DDR0_18_DLL_DQS_DELAY_4_ENCODE(DLL_DQS_DELAY) |
DDR0_18_DLL_DQS_DELAY_3_ENCODE(DLL_DQS_DELAY) |
DDR0_18_DLL_DQS_DELAY_2_ENCODE(DLL_DQS_DELAY) |
DDR0_18_DLL_DQS_DELAY_1_ENCODE(DLL_DQS_DELAY));
mtsdram(DDR0_19, DDR0_19_DLL_DQS_DELAY_8_ENCODE(DLL_DQS_DELAY) |
DDR0_19_DLL_DQS_DELAY_7_ENCODE(DLL_DQS_DELAY) |
DDR0_19_DLL_DQS_DELAY_6_ENCODE(DLL_DQS_DELAY) |
DDR0_19_DLL_DQS_DELAY_5_ENCODE(DLL_DQS_DELAY));
mtsdram(DDR0_20, DDR0_20_DLL_DQS_BYPASS_3_ENCODE(DLL_DQS_BYPASS) |
DDR0_20_DLL_DQS_BYPASS_2_ENCODE(DLL_DQS_BYPASS) |
DDR0_20_DLL_DQS_BYPASS_1_ENCODE(DLL_DQS_BYPASS) |
DDR0_20_DLL_DQS_BYPASS_0_ENCODE(DLL_DQS_BYPASS));
mtsdram(DDR0_21, DDR0_21_DLL_DQS_BYPASS_7_ENCODE(DLL_DQS_BYPASS) |
DDR0_21_DLL_DQS_BYPASS_6_ENCODE(DLL_DQS_BYPASS) |
DDR0_21_DLL_DQS_BYPASS_5_ENCODE(DLL_DQS_BYPASS) |
DDR0_21_DLL_DQS_BYPASS_4_ENCODE(DLL_DQS_BYPASS));
program_ddr0_22(dimm_ranks, iic0_dimm_addr, num_dimm_banks, width);
mtsdram(DDR0_23, DDR0_23_ODT_RD_MAP_CS0_ENCODE(0x0) |
DDR0_23_FWC_ENCODE(0));
program_ddr0_24(ranks);
program_ddr0_26(sdram_freq);
program_ddr0_27(sdram_freq);
mtsdram(DDR0_28, DDR0_28_EMRS3_DATA_ENCODE(0x0000) |
DDR0_28_EMRS2_DATA_ENCODE(0x0000));
mtsdram(DDR0_31, DDR0_31_XOR_CHECK_BITS_ENCODE(0x0000));
mtsdram(DDR0_42, DDR0_42_ADDR_PINS_DECODE(14 - rows) |
DDR0_42_CASLAT_LIN_GATE_ENCODE(2 * cas_latency));
program_ddr0_43(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq,
cols, banks);
program_ddr0_44(dimm_ranks, iic0_dimm_addr, num_dimm_banks, sdram_freq);
denali_sdram_register_dump();
dram_size = (width >= 64) ? 8 : 4;
dram_size *= 1 << cols;
dram_size *= banks;
dram_size *= 1 << rows;
dram_size *= ranks;
debug("dram_size = %lu\n", dram_size);
/* Start the SDRAM controler */
mtsdram(DDR0_02, DDR0_02_START_ENCODE(1));
denali_wait_for_dlllock();
#if defined(CONFIG_DDR_DATA_EYE)
/*
* Map the first 1 MiB of memory in the TLB, and perform the data eye
* search.
*/
program_tlb(0, CONFIG_SYS_SDRAM_BASE, TLB_1MB_SIZE, TLB_WORD2_I_ENABLE);
denali_core_search_data_eye();
denali_sdram_register_dump();
remove_tlb(CONFIG_SYS_SDRAM_BASE, TLB_1MB_SIZE);
#endif
#if defined(CONFIG_ZERO_SDRAM) || defined(CONFIG_DDR_ECC)
program_tlb(0, CONFIG_SYS_SDRAM_BASE, dram_size, 0);
sync();
/* Zero the memory */
debug("Zeroing SDRAM...");
#if defined(CONFIG_SYS_MEM_TOP_HIDE)
dcbz_area(CONFIG_SYS_SDRAM_BASE, dram_size - CONFIG_SYS_MEM_TOP_HIDE);
#else
#error Please define CONFIG_SYS_MEM_TOP_HIDE (see README) in your board config file
#endif
/* Write modified dcache lines back to memory */
clean_dcache_range(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_SDRAM_BASE + dram_size - CONFIG_SYS_MEM_TOP_HIDE);
debug("Completed\n");
sync();
remove_tlb(CONFIG_SYS_SDRAM_BASE, dram_size);
#if defined(CONFIG_DDR_ECC)
/*
* If ECC is enabled, clear and enable interrupts
*/
if (is_ecc_enabled()) {
u32 val;
sync();
/* Clear error status */
mfsdram(DDR0_00, val);
mtsdram(DDR0_00, val | DDR0_00_INT_ACK_ALL);
/* Set 'int_mask' parameter to functionnal value */
mfsdram(DDR0_01, val);
mtsdram(DDR0_01, (val & ~DDR0_01_INT_MASK_MASK) |
DDR0_01_INT_MASK_ALL_OFF);
#if defined(CONFIG_DDR_DATA_EYE)
/*
* Running denali_core_search_data_eye() when ECC is enabled
* causes non-ECC machine checks. This clears them.
*/
print_mcsr();
mtspr(SPRN_MCSR, mfspr(SPRN_MCSR));
print_mcsr();
#endif
sync();
}
#endif /* defined(CONFIG_DDR_ECC) */
#endif /* defined(CONFIG_ZERO_SDRAM) || defined(CONFIG_DDR_ECC) */
program_tlb(0, CONFIG_SYS_SDRAM_BASE, dram_size, MY_TLB_WORD2_I_ENABLE);
return dram_size;
}
/*************************************************************************
*
* initdram -- 440EPx's DDR controller is a DENALI Core
*
************************************************************************/
phys_size_t initdram (int board_type)
{
#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_LCD4_LWMON5)
/* CL=4 */
mtsdram(DDR0_02, 0x00000000);
mtsdram(DDR0_00, 0x0000190A);
mtsdram(DDR0_01, 0x01000000);
mtsdram(DDR0_03, 0x02040803); /* A suitable burst length was taken. CAS is right for our board */
mtsdram(DDR0_04, 0x0B030300);
mtsdram(DDR0_05, 0x02020308);
mtsdram(DDR0_06, 0x0003C812);
mtsdram(DDR0_07, 0x00090100);
mtsdram(DDR0_08, 0x03c80001);
mtsdram(DDR0_09, 0x00011D5F);
mtsdram(DDR0_10, 0x00000100);
mtsdram(DDR0_11, 0x000CC800);
mtsdram(DDR0_12, 0x00000003);
mtsdram(DDR0_14, 0x00000000);
mtsdram(DDR0_17, 0x1e000000);
mtsdram(DDR0_18, 0x1e1e1e1e);
mtsdram(DDR0_19, 0x1e1e1e1e);
mtsdram(DDR0_20, 0x0B0B0B0B);
mtsdram(DDR0_21, 0x0B0B0B0B);
#ifdef CONFIG_DDR_ECC
mtsdram(DDR0_22, 0x00267F0B | DDR0_22_CTRL_RAW_ECC_ENABLE); /* enable ECC */
#else
mtsdram(DDR0_22, 0x00267F0B);
#endif
mtsdram(DDR0_23, 0x01000000);
mtsdram(DDR0_24, 0x01010001);
mtsdram(DDR0_26, 0x2D93028A);
mtsdram(DDR0_27, 0x0784682B);
mtsdram(DDR0_28, 0x00000080);
mtsdram(DDR0_31, 0x00000000);
mtsdram(DDR0_42, 0x01000008);
mtsdram(DDR0_43, 0x050A0200);
mtsdram(DDR0_44, 0x00000005);
mtsdram(DDR0_02, 0x00000001); /* Activate the denali core */
denali_wait_for_dlllock();
#if defined(CONFIG_DDR_DATA_EYE)
/* -----------------------------------------------------------+
* Perform data eye search if requested.
* ----------------------------------------------------------*/
program_tlb(0, CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MBYTES_SDRAM << 20,
TLB_WORD2_I_ENABLE);
denali_core_search_data_eye();
remove_tlb(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MBYTES_SDRAM << 20);
#endif
/*
* Program tlb entries for this size (dynamic)
*/
program_tlb(0, CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MBYTES_SDRAM << 20,
MY_TLB_WORD2_I_ENABLE);
#if defined(CONFIG_DDR_ECC)
#if defined(CONFIG_4xx_DCACHE)
/*
* If ECC is enabled, initialize the parity bits.
*/
program_ecc(0, CONFIG_SYS_MBYTES_SDRAM << 20, 0);
#else /* CONFIG_4xx_DCACHE */
/*
* Setup 2nd TLB with same physical address but different virtual address
* with cache enabled. This is done for fast ECC generation.
*/
program_tlb(0, CONFIG_SYS_DDR_CACHED_ADDR, CONFIG_SYS_MBYTES_SDRAM << 20, 0);
/*
* If ECC is enabled, initialize the parity bits.
*/
program_ecc(CONFIG_SYS_DDR_CACHED_ADDR, CONFIG_SYS_MBYTES_SDRAM << 20, 0);
/*
* Now after initialization (auto-calibration and ECC generation)
* remove the TLB entries with caches enabled and program again with
* desired cache functionality
*/
remove_tlb(CONFIG_SYS_DDR_CACHED_ADDR, CONFIG_SYS_MBYTES_SDRAM << 20);
#endif /* CONFIG_4xx_DCACHE */
#endif /* CONFIG_DDR_ECC */
/*
* Clear possible errors resulting from data-eye-search.
* If not done, then we could get an interrupt later on when
* exceptions are enabled.
*/
set_mcsr(get_mcsr());
#endif /* CONFIG_SPL_BUILD */
return (CONFIG_SYS_MBYTES_SDRAM << 20);
}
/*
* initdram -- 440EPx's DDR controller is a DENALI Core
*/
int initdram_by_rb(int rows, int banks)
{
ulong speed = get_bus_freq(0);
mtsdram(DDR0_02, 0x00000000);
mtsdram(DDR0_00, 0x0000190A);
mtsdram(DDR0_01, 0x01000000);
mtsdram(DDR0_03, 0x02030602);
mtsdram(DDR0_04, 0x0A020200);
mtsdram(DDR0_05, 0x02020308);
mtsdram(DDR0_06, 0x0102C812);
mtsdram(DDR0_07, 0x000D0100);
mtsdram(DDR0_08, 0x02430001);
mtsdram(DDR0_09, 0x00011D5F);
mtsdram(DDR0_10, 0x00000100);
mtsdram(DDR0_11, 0x0027C800);
mtsdram(DDR0_12, 0x00000003);
mtsdram(DDR0_14, 0x00000000);
mtsdram(DDR0_17, 0x19000000);
mtsdram(DDR0_18, 0x19191919);
mtsdram(DDR0_19, 0x19191919);
mtsdram(DDR0_20, 0x0B0B0B0B);
mtsdram(DDR0_21, 0x0B0B0B0B);
mtsdram(DDR0_22, 0x00267F0B);
mtsdram(DDR0_23, 0x00000000);
mtsdram(DDR0_24, 0x01010002);
if (speed > 133333334)
mtsdram(DDR0_26, 0x5B26050C);
else
mtsdram(DDR0_26, 0x5B260408);
mtsdram(DDR0_27, 0x0000682B);
mtsdram(DDR0_28, 0x00000000);
mtsdram(DDR0_31, 0x00000000);
mtsdram(DDR0_42,
DDR0_42_ADDR_PINS_DECODE(14 - rows) |
0x00000006);
mtsdram(DDR0_43,
DDR0_43_EIGHT_BANK_MODE_ENCODE(8 == banks ? 1 : 0) |
0x030A0200);
mtsdram(DDR0_44, 0x00000003);
mtsdram(DDR0_02, 0x00000001);
denali_wait_for_dlllock();
#ifdef CONFIG_DDR_DATA_EYE
/*
* Perform data eye search if requested.
*/
denali_core_search_data_eye();
#endif
/*
* Clear possible errors resulting from data-eye-search.
* If not done, then we could get an interrupt later on when
* exceptions are enabled.
*/
set_mcsr(get_mcsr());
return 0;
}
/*************************************************************************
*
* initdram -- 440EPx's DDR controller is a DENALI Core
*
************************************************************************/
long int initdram (int board_type)
{
#if 0 /* test-only: will remove this define later, when ECC problems are solved! */
/* CL=3 */
mtsdram(DDR0_02, 0x00000000);
mtsdram(DDR0_00, 0x0000190A);
mtsdram(DDR0_01, 0x01000000);
mtsdram(DDR0_03, 0x02030603); /* A suitable burst length was taken. CAS is right for our board */
mtsdram(DDR0_04, 0x0A030300);
mtsdram(DDR0_05, 0x02020308);
mtsdram(DDR0_06, 0x0103C812);
mtsdram(DDR0_07, 0x00090100);
mtsdram(DDR0_08, 0x02c80001);
mtsdram(DDR0_09, 0x00011D5F);
mtsdram(DDR0_10, 0x00000300);
mtsdram(DDR0_11, 0x000CC800);
mtsdram(DDR0_12, 0x00000003);
mtsdram(DDR0_14, 0x00000000);
mtsdram(DDR0_17, 0x1e000000);
mtsdram(DDR0_18, 0x1e1e1e1e);
mtsdram(DDR0_19, 0x1e1e1e1e);
mtsdram(DDR0_20, 0x0B0B0B0B);
mtsdram(DDR0_21, 0x0B0B0B0B);
#ifdef CONFIG_DDR_ECC
mtsdram(DDR0_22, 0x00267F0B | DDR0_22_CTRL_RAW_ECC_ENABLE); /* enable ECC */
#else
mtsdram(DDR0_22, 0x00267F0B);
#endif
mtsdram(DDR0_23, 0x01000000);
mtsdram(DDR0_24, 0x01010001);
mtsdram(DDR0_26, 0x2D93028A);
mtsdram(DDR0_27, 0x0784682B);
mtsdram(DDR0_28, 0x00000080);
mtsdram(DDR0_31, 0x00000000);
mtsdram(DDR0_42, 0x01000006);
mtsdram(DDR0_43, 0x030A0200);
mtsdram(DDR0_44, 0x00000003);
mtsdram(DDR0_02, 0x00000001); /* Activate the denali core */
#else
/* CL=4 */
mtsdram(DDR0_02, 0x00000000);
mtsdram(DDR0_00, 0x0000190A);
mtsdram(DDR0_01, 0x01000000);
mtsdram(DDR0_03, 0x02040803); /* A suitable burst length was taken. CAS is right for our board */
mtsdram(DDR0_04, 0x0B030300);
mtsdram(DDR0_05, 0x02020308);
mtsdram(DDR0_06, 0x0003C812);
mtsdram(DDR0_07, 0x00090100);
mtsdram(DDR0_08, 0x03c80001);
mtsdram(DDR0_09, 0x00011D5F);
mtsdram(DDR0_10, 0x00000300);
mtsdram(DDR0_11, 0x000CC800);
mtsdram(DDR0_12, 0x00000003);
mtsdram(DDR0_14, 0x00000000);
mtsdram(DDR0_17, 0x1e000000);
mtsdram(DDR0_18, 0x1e1e1e1e);
mtsdram(DDR0_19, 0x1e1e1e1e);
mtsdram(DDR0_20, 0x0B0B0B0B);
mtsdram(DDR0_21, 0x0B0B0B0B);
#ifdef CONFIG_DDR_ECC
mtsdram(DDR0_22, 0x00267F0B | DDR0_22_CTRL_RAW_ECC_ENABLE); /* enable ECC */
#else
mtsdram(DDR0_22, 0x00267F0B);
#endif
mtsdram(DDR0_23, 0x01000000);
mtsdram(DDR0_24, 0x01010001);
mtsdram(DDR0_26, 0x2D93028A);
mtsdram(DDR0_27, 0x0784682B);
mtsdram(DDR0_28, 0x00000080);
mtsdram(DDR0_31, 0x00000000);
mtsdram(DDR0_42, 0x01000008);
mtsdram(DDR0_43, 0x050A0200);
mtsdram(DDR0_44, 0x00000005);
mtsdram(DDR0_02, 0x00000001); /* Activate the denali core */
#endif
wait_for_dlllock();
/*
* Program tlb entries for this size (dynamic)
*/
program_tlb(0, 0, CFG_MBYTES_SDRAM << 20, MY_TLB_WORD2_I_ENABLE);
/*
* Setup 2nd TLB with same physical address but different virtual address
* with cache enabled. This is done for fast ECC generation.
*/
program_tlb(0, CFG_DDR_CACHED_ADDR, CFG_MBYTES_SDRAM << 20, 0);
#ifdef CONFIG_DDR_DATA_EYE
/*
* Perform data eye search if requested.
*/
denali_core_search_data_eye(CFG_DDR_CACHED_ADDR, CFG_MBYTES_SDRAM << 20);
#endif
#ifdef CONFIG_DDR_ECC
/*
* If ECC is enabled, initialize the parity bits.
*/
program_ecc(CFG_DDR_CACHED_ADDR, CFG_MBYTES_SDRAM << 20, 0);
#endif
/*
* Clear possible errors resulting from data-eye-search.
* If not done, then we could get an interrupt later on when
* exceptions are enabled.
*/
set_mcsr(get_mcsr());
return (CFG_MBYTES_SDRAM << 20);
}
