/**
* \brief main function
*/
int main(void)
{
struct dma_channel_config config;
uint32_t checksum;
pmic_init();
board_init();
sysclk_init();
sleepmgr_init();
// Randomly selected data
source[0] = 0xAA;
source[1] = 0xBB;
source[2] = 0xCC;
source[3] = 0xDD;
source[4] = 0xEE;
source[5] = 0xFF;
// Calculate checksum for the data
checksum = crc_io_checksum((void*)source, 6, CRC_16BIT);
// Append the checksum to the data, big endian
crc16_append_value(checksum, source+6);
//Enable the CRC module for DMA
crc_dma_checksum_start(DMA_CHANNEL, CRC_16BIT);
// Enable DMA
dma_enable();
// Set callback function for DMA completion
dma_set_callback(DMA_CHANNEL, example_crc_dma_transfer_done);
// Make sure config is all zeroed out so we don't get any stray bits
memset(&config, 0, sizeof(config));
/**
* This example will configure a DMA channel with the following
* settings:
* - Low interrupt priority
* - 1 byte burst length
* - DMA_BUFFER_SIZE bytes for each transfer
* - Reload source and destination address at end of each transfer
* - Increment source and destination address during transfer
* - Source address is set to \ref source
* - Destination address is set to \ref destination
*/
dma_channel_set_interrupt_level(&config, PMIC_LVL_LOW);
dma_channel_set_burst_length(&config, DMA_CH_BURSTLEN_1BYTE_gc);
dma_channel_set_transfer_count(&config, DMA_BUFFER_SIZE);
dma_channel_set_src_reload_mode(&config,
DMA_CH_SRCRELOAD_TRANSACTION_gc);
dma_channel_set_dest_reload_mode(&config,
DMA_CH_DESTRELOAD_TRANSACTION_gc);
dma_channel_set_src_dir_mode(&config, DMA_CH_SRCDIR_INC_gc);
dma_channel_set_dest_dir_mode(&config, DMA_CH_DESTDIR_INC_gc);
dma_channel_set_source_address(&config, (uint16_t)(uintptr_t)source);
dma_channel_set_destination_address(&config,
(uint16_t)(uintptr_t)destination);
dma_channel_write_config(DMA_CHANNEL, &config);
// Use the configuration above by enabling the DMA channel in use.
dma_channel_enable(DMA_CHANNEL);
// Enable interrupts
cpu_irq_enable();
// Trigger the DMA transfer
dma_channel_trigger_block_transfer(DMA_CHANNEL);
// Light the first LED to indicate that the DMA has started.
gpio_set_pin_low(LED0_GPIO);
while (true) {
/*
* Force a NOP instruction for an eventual placement of a debug
* session breakpoint.
*/
asm("nop\n");
}
}
/**
* \brief Test read from fixed location, trigger from timer and callback
*
* \note This test sets up a timer to trigger the DMA module,
* which in turn reads the timer_overflow_counter variable and writes
* it to memory sequentially. It then checks to see that the memory block
* written is sequential according to the overflow count.
*
* \param test Current test
*/
static void run_dma_triggered_with_callback(const struct test_case *test)
{
struct dma_channel_config config_params;
bool success;
/* Null the buffer */
set_buffer(dest_block_tc, 0x0000);
/* Null out the config parameter struct */
memset(&config_params, 0, sizeof(config_params));
/*
* Enable the timer, and set it to count up.
* When it overflows, it triggers the DMA to
* read timer_overflow_counter. */
tc_enable(&TIMER);
tc_set_direction(&TIMER, TC_UP);
tc_write_period(&TIMER, TIMER_PERIOD);
tc_set_resolution(&TIMER, TIMER_RESOLUTION);
tc_set_overflow_interrupt_level(&TIMER, PMIC_LVL_LOW);
tc_set_overflow_interrupt_callback(&TIMER, timer_overflow_callback);
/* Enable the DMA module */
dma_enable();
/* Set callback for transfer done */
dma_set_callback(DMA_CHANNEL_0, dma_transfer_is_complete);
/* Set low interrupt level */
dma_channel_set_interrupt_level(&config_params, PMIC_LVL_LOW);
/* Set up the DMA to read the timer value
*
* - Single shot transfer mode
* - Two byte (16-bit) burst length
* - Increment on source and destination
* - Reload on burst for source
* - No reload for destination
*/
dma_channel_set_single_shot(&config_params);
dma_channel_set_burst_length(&config_params,
DMA_CH_BURSTLEN_1BYTE_gc);
dma_channel_set_src_reload_mode(&config_params,
DMA_CH_SRCRELOAD_BURST_gc);
dma_channel_set_src_dir_mode(&config_params,
DMA_CH_SRCDIR_FIXED_gc);
dma_channel_set_dest_reload_mode(&config_params,
DMA_CH_DESTRELOAD_NONE_gc);
dma_channel_set_dest_dir_mode(&config_params,
DMA_CH_DESTDIR_INC_gc);
/* Set trigger source to TCC0's overflow */
dma_channel_set_trigger_source(&config_params,
DMA_CH_TRIGSRC_TCC0_OVF_gc);
/* Transfer DEST_BLOCK_TC_SIZE bytes */
dma_channel_set_transfer_count(&config_params,
DEST_BLOCK_TC_SIZE);
/* Set address */
dma_channel_set_source_address(&config_params,
(uint16_t)(uintptr_t)&timer_overflow_counter);
dma_channel_set_destination_address(&config_params,
(uint16_t)(uintptr_t)dest_block_tc);
/* Reset the channel */
dma_channel_reset(DMA_CHANNEL_0);
/* Write the config */
dma_channel_write_config(DMA_CHANNEL_0, &config_params);
/* Enable the channel */
dma_channel_enable(DMA_CHANNEL_0);
/* Wait for transfer to finish */
while (!dma_has_completed) {
/* Intentionally left empty */
}
/* Disable DMA */
dma_disable();
/* Verify that the result is as expected */
success = block_compare(dest_block_tc,
expected_result_tc, DEST_BLOCK_TC_SIZE);
test_assert_true(test, success, "Result is not as expected");
}
