/*---------------------------------------------------------------------------*/
void
button_sensor_init(void)
{
struct extint_chan_conf config_extint_chan;
struct port_config pin_conf;
port_get_config_defaults(&pin_conf);
pin_conf.direction = PORT_PIN_DIR_INPUT;
pin_conf.input_pull = PORT_PIN_PULL_UP;
port_pin_set_config(BUTTON_0_PIN, &pin_conf);
// extint_enable();
extint_chan_get_config_defaults(&config_extint_chan);
config_extint_chan.gpio_pin = BUTTON_0_EIC_PIN;
config_extint_chan.gpio_pin_mux = BUTTON_0_EIC_MUX;
config_extint_chan.gpio_pin_pull = EXTINT_PULL_UP;
config_extint_chan.detection_criteria = EXTINT_DETECT_FALLING;
// config_extint_chan.detection_criteria = EXTINT_DETECT_BOTH;
extint_chan_set_config(BUTTON_0_EIC_LINE, &config_extint_chan);
extint_register_callback((extint_callback_t)extint_detection_callback,
BUTTON_0_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_enable_callback(BUTTON_0_EIC_LINE, EXTINT_CALLBACK_TYPE_DETECT);
timer_set(&debouncetimer, 0);
system_interrupt_enable_global();
/* on by default */
button_sensor_configure(0, 1);
}
/** Configures and registers the External Interrupt callback function with the
* driver.
*/
static void configure_eic_callback(void)
{
extint_register_callback(extint_callback,
BUTTON_0_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_enable_callback(BUTTON_0_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
}
/*==============================================================================
hal_extIntInit()
=============================================================================*/
uint8_t hal_extIntInit( en_targetExtInt_t e_intSource,
pfn_intCallb_t pfn_intCallback )
{
int8_t c_ret = 0;
if( pfn_intCallback != NULL )
{
switch( e_intSource )
{
case E_TARGET_RADIO_INT:
//! [setup_init]
//extint_enable();
//! [conf_channel]
//! [setup_1]
extint_chan_get_config_defaults( &( radio_extInt.st_chan ) );
//! [setup_1]
//! [setup_2]
radio_extInt.st_chan.gpio_pin = radio_extInt.l_pin; //EXT1_IRQ_PIN;
radio_extInt.st_chan.gpio_pin_mux = radio_extInt.l_pinMux; //MUX_PB04A_EIC_EXTINT4;
radio_extInt.st_chan.gpio_pin_pull = radio_extInt.c_pinPull; //EXTINT_PULL_DOWN;
radio_extInt.st_chan.detection_criteria =
radio_extInt.c_detCrit; //EXTINT_DETECT_RISING;
//! [setup_2]
//! [setup_3]
extint_chan_set_config( (uint8_t)radio_extInt.l_line,
&( radio_extInt.st_chan ) );
//! [setup_3]
_radio_callback = pfn_intCallback;
//! [setup_4]
extint_register_callback(
(extint_callback_t)_isr_radio_callback,
(uint8_t)radio_extInt.l_line,
EXTINT_CALLBACK_TYPE_DETECT );
//! [setup_4]
//! [setup_5]
extint_chan_enable_callback( (uint8_t)radio_extInt.l_line, //EXT1_IRQ_INPUT,
EXTINT_CALLBACK_TYPE_DETECT );
//! [setup_6]
//! [conf_channel]
//! [setup_init]
system_interrupt_enable_global();
c_ret = 1;
break;
case E_TARGET_USART_INT:
break;
default:
break;
}
}
return c_ret;
} /* hal_extIntInit() */
void configure_extint_callbacks(void)
{
//! [setup_5]
extint_register_callback(extint_detection_callback,
BUTTON_0_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
//! [setup_5]
//! [setup_6]
extint_chan_enable_callback(BUTTON_0_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
//! [setup_6]
}
void cph_deca_init_gpio(void) {
struct extint_chan_conf config_chan;
extint_chan_get_config_defaults(&config_chan);
config_chan.gpio_pin = DW_IRQ_PIN;
config_chan.gpio_pin_mux = DW_IRQ_PIN_MUX;
config_chan.gpio_pin_pull = DW_IRQ_PIN_PULL;
config_chan.detection_criteria = DW_IRQ_PIN_DETECT;
extint_chan_set_config(DW_IRQ_LINE, &config_chan);
extint_register_callback(cph_deca_isr, DW_IRQ_LINE, EXTINT_CALLBACK_TYPE_DETECT);
}
void config_wind_speed()
{
struct extint_chan_conf wind_speed_chan;
extint_chan_get_config_defaults(&wind_speed_chan);
wind_speed_chan.gpio_pin = WIND_SPEED_INTERRUPT_PIN;
wind_speed_chan.gpio_pin_mux = WIND_SPEED_INTERRUPT_MUX;
wind_speed_chan.gpio_pin_pull = EXTINT_PULL_UP;
wind_speed_chan.detection_criteria = EXTINT_DETECT_RISING;
extint_chan_set_config(WIND_SPEED_INTERRUPT_LINE, &wind_speed_chan);
extint_register_callback(wind_click_handle, WIND_SPEED_INTERRUPT_LINE, EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_enable_callback(WIND_SPEED_INTERRUPT_LINE, EXTINT_CALLBACK_TYPE_DETECT);
return;
}
WEATHER_ERR_T config_rain_guage()
{
struct extint_chan_conf rain_extint_chan;
extint_chan_get_config_defaults(&rain_extint_chan);
rain_extint_chan.gpio_pin = RAIN_INTERRUPT_PIN;
rain_extint_chan.gpio_pin_mux = RAIN_INTERRUPT_MUX;
rain_extint_chan.gpio_pin_pull = EXTINT_PULL_UP;
rain_extint_chan.detection_criteria = EXTINT_DETECT_RISING;
extint_chan_set_config(RAIN_INTERRUPT_LINE, &rain_extint_chan);
extint_register_callback(rain_click_handle, RAIN_INTERRUPT_LINE, EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_enable_callback(RAIN_INTERRUPT_LINE, EXTINT_CALLBACK_TYPE_DETECT);
return W_ERR_NONE;
}
/**
* \brief Initializes and enables interrupt pin change
*/
static void ui_enable_asynchronous_interrupt(void)
{
/* Initialize EIC for button wakeup */
struct extint_chan_conf eint_chan_conf;
extint_chan_get_config_defaults(&eint_chan_conf);
eint_chan_conf.gpio_pin = BUTTON_0_EIC_PIN;
eint_chan_conf.gpio_pin_mux = BUTTON_0_EIC_MUX;
eint_chan_conf.detection_criteria = EXTINT_DETECT_FALLING;
eint_chan_conf.filter_input_signal = true;
extint_chan_set_config(BUTTON_0_EIC_LINE, &eint_chan_conf);
extint_register_callback(UI_WAKEUP_HANDLER,
BUTTON_0_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_clear_detected(BUTTON_0_EIC_LINE);
extint_chan_enable_callback(BUTTON_0_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
}
/*
* @fn nm_bsp_register_isr
* @brief Register interrupt service routine
* @param[IN] pfIsr
* Pointer to ISR handler
*/
void nm_bsp_register_isr(tpfNmBspIsr pfIsr)
{
struct extint_chan_conf config_extint_chan;
gpfIsr = pfIsr;
extint_chan_get_config_defaults(&config_extint_chan);
config_extint_chan.gpio_pin = CONF_WINC_SPI_INT_PIN;
config_extint_chan.gpio_pin_mux = CONF_WINC_SPI_INT_MUX;
config_extint_chan.gpio_pin_pull = EXTINT_PULL_UP;
config_extint_chan.detection_criteria = EXTINT_DETECT_FALLING;
extint_chan_set_config(CONF_WINC_SPI_INT_EIC, &config_extint_chan);
extint_register_callback(chip_isr, CONF_WINC_SPI_INT_EIC,
EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_enable_callback(CONF_WINC_SPI_INT_EIC,
EXTINT_CALLBACK_TYPE_DETECT);
}
//! [config_eic]
static void configure_eic(void)
{
//! [eic_chan_setup]
//! [eic_setup_1]
struct extint_chan_conf config;
//! [eic_setup_1]
//! [eic_setup_2]
extint_chan_get_config_defaults(&config);
//! [eic_setup_2]
//! [eic_setup_3]
config.filter_input_signal = true;
config.detection_criteria = EXTINT_DETECT_BOTH;
config.gpio_pin = CONF_FAULT_EIC_PIN;
config.gpio_pin_mux = CONF_FAULT_EIC_PIN_MUX;
//! [eic_setup_3]
//! [eic_setup_4]
extint_chan_set_config(CONF_FAULT_EIC_LINE, &config);
//! [eic_setup_4]
//! [eic_chan_setup]
//! [eic_event_setup]
//! [eic_event_setup_1]
struct extint_events events;
memset(&events, 0, sizeof(struct extint_events));
//! [eic_event_setup_1]
//! [eic_event_setup_2]
events.generate_event_on_detect[CONF_FAULT_EIC_LINE] = true;
//! [eic_event_setup_2]
//! [eic_event_setup_3]
extint_enable_events(&events);
//! [eic_event_setup_3]
//! [eic_event_setup]
//! [eic_callback_setup]
//! [eic_callback_setup_1]
extint_register_callback(eic_callback_to_clear_halt,
CONF_FAULT_EIC_LINE, EXTINT_CALLBACK_TYPE_DETECT);
//! [eic_callback_setup_1]
//! [eic_callback_setup_2]
extint_chan_enable_callback(CONF_FAULT_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
//! [eic_callback_setup_2]
//! [eic_callback_setup]
}
void configurationPPS(void){
struct extint_chan_conf eint_chan_conf;
extint_chan_get_config_defaults(&eint_chan_conf);
// put the button as EXTINT
eint_chan_conf.gpio_pin = PIN_PA28A_EIC_EXTINT8;
eint_chan_conf.gpio_pin_mux = MUX_PA28A_EIC_EXTINT8;
/** Detect rising signal edges */
eint_chan_conf.detection_criteria = EXTINT_DETECT_RISING;
eint_chan_conf.filter_input_signal = false;
extint_chan_set_config(8, &eint_chan_conf);
//configuration callback
extint_register_callback(ppsISR,8,EXTINT_CALLBACK_TYPE_DETECT);
//activation callback
extint_chan_enable_callback(8,EXTINT_CALLBACK_TYPE_DETECT);
pin_state=false;
}
void ui_init(void)
{
struct extint_chan_conf config_extint_chan;
extint_chan_get_config_defaults(&config_extint_chan);
config_extint_chan.gpio_pin = BUTTON_0_EIC_PIN;
config_extint_chan.gpio_pin_mux = BUTTON_0_EIC_MUX;
config_extint_chan.gpio_pin_pull = EXTINT_PULL_UP;
config_extint_chan.filter_input_signal = true;
config_extint_chan.detection_criteria = EXTINT_DETECT_FALLING;
extint_chan_set_config(BUTTON_0_EIC_LINE, &config_extint_chan);
extint_register_callback(ui_wakeup_handler, BUTTON_0_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_enable_callback(BUTTON_0_EIC_LINE,EXTINT_CALLBACK_TYPE_DETECT);
/* Initialize LEDs */
LED_On(LED_0_PIN);
}
/**
* USB ID pin configuration
*/
static void usb_id_config(void)
{
struct extint_chan_conf eint_chan_conf;
extint_chan_get_config_defaults(&eint_chan_conf);
eint_chan_conf.gpio_pin = USB_ID_PIN;
eint_chan_conf.gpio_pin_mux = USB_ID_EIC_MUX;
eint_chan_conf.detection_criteria = EXTINT_DETECT_BOTH;
eint_chan_conf.filter_input_signal = true;
extint_chan_disable_callback(USB_ID_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_set_config(USB_ID_EIC_LINE, &eint_chan_conf);
extint_register_callback(usb_id_handler,
USB_ID_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_enable_callback(USB_ID_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
}
/**
* \brief Configure the INTN interrupt.
*
* \param p_handler callback pointer to use when INTN interrupt raises.
*/
void configure_intn(void (*p_handler) (void))
{
struct extint_chan_conf eic_conf;
/* Configure the external interrupt channel. */
extint_chan_get_config_defaults(&eic_conf);
eic_conf.gpio_pin = KSZ8851SNL_INTN_EIC_PIN;
eic_conf.gpio_pin_mux = KSZ8851SNL_INTN_EIC_PIN_MUX;
eic_conf.gpio_pin_pull = EXTINT_PULL_UP;
eic_conf.detection_criteria = EXTINT_DETECT_FALLING;
eic_conf.filter_input_signal = true;
extint_chan_set_config(KSZ8851SNL_INTN_EIC_CHANNEL, &eic_conf);
/* Register and enable the callback function. */
extint_register_callback(p_handler,
KSZ8851SNL_INTN_EIC_CHANNEL,
EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_enable_callback(KSZ8851SNL_INTN_EIC_CHANNEL,
EXTINT_CALLBACK_TYPE_DETECT);
}
/**
* \internal
* \brief Setup function for callback mode test.
*
* This function sets up the GPIO pin, the external interrupt channel &
* the callback function.
*
* \param test Current test case.
*/
static void setup_extint_callback_mode_test(const struct test_case *test)
{
/* Configure the GPIO pin */
port_get_config_defaults(&pin_conf);
pin_conf.direction = PORT_PIN_DIR_OUTPUT;
pin_conf.input_pull = PORT_PIN_PULL_NONE;
port_pin_set_config(GPIO_TEST_PIN_EXTINT, &pin_conf);
port_pin_set_output_level(GPIO_TEST_PIN_EXTINT, true);
/* Configure the external interrupt channel */
extint_chan_get_config_defaults(&eic_conf);
eic_conf.gpio_pin = EIC_TEST_PIN;
eic_conf.gpio_pin_mux = EIC_TEST_PIN_MUX;
eic_conf.gpio_pin_pull = EXTINT_PULL_UP;
eic_conf.detection_criteria = EXTINT_DETECT_FALLING;
extint_chan_set_config(EIC_TEST_CHANNEL, &eic_conf);
/* Register and enable the callback function */
extint_register_callback(extint_user_callback,
EIC_TEST_CHANNEL,
EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_enable_callback(EIC_TEST_CHANNEL,
EXTINT_CALLBACK_TYPE_DETECT);
}
/*---------------------------------------------------------------------------*/
static void
configure_button(void)
{
/* Set buttons as inputs */
struct port_config pin_conf;
port_get_config_defaults(&pin_conf);
pin_conf.direction = PORT_PIN_DIR_INPUT;
pin_conf.input_pull = PORT_PIN_PULL_UP;
port_pin_set_config(BUTTON_0_PIN, &pin_conf);
/* Configure interrupt */
struct extint_chan_conf config_extint_chan;
extint_chan_get_config_defaults(&config_extint_chan);
config_extint_chan.gpio_pin = BUTTON_0_EIC_PIN;
config_extint_chan.gpio_pin_mux = BUTTON_0_EIC_MUX;
config_extint_chan.gpio_pin_pull = EXTINT_PULL_UP;
config_extint_chan.detection_criteria = EXTINT_DETECT_BOTH;
extint_chan_set_config(BUTTON_0_EIC_LINE, &config_extint_chan);
/* Register interrupt callbacks */
extint_register_callback(extint_detection_callback,
BUTTON_0_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
}
void configure_extint_callbacks(void)
{
extint_register_callback(extint_detection_callback_1, 2, EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_enable_callback(2, EXTINT_CALLBACK_TYPE_DETECT);
}
