/*
* Transport for the Sandisk SDDR-55
*/
int sddr55_transport(Scsi_Cmnd *srb, struct us_data *us)
{
int result;
int i;
unsigned char inquiry_response[36] = {
0x00, 0x80, 0x00, 0x02, 0x1F, 0x00, 0x00, 0x00
};
unsigned char mode_page_01[16] = { // write-protected for now
0x03, 0x00, 0x80, 0x00,
0x01, 0x0A,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
};
unsigned char *ptr;
unsigned long capacity;
unsigned int lba;
unsigned int pba;
unsigned int page;
unsigned short pages;
struct sddr55_card_info *info;
if (!us->extra) {
us->extra = kmalloc(
sizeof(struct sddr55_card_info), GFP_NOIO);
if (!us->extra)
return USB_STOR_TRANSPORT_ERROR;
memset(us->extra, 0, sizeof(struct sddr55_card_info));
us->extra_destructor = sddr55_card_info_destructor;
}
info = (struct sddr55_card_info *)(us->extra);
ptr = (unsigned char *)srb->request_buffer;
if (srb->cmnd[0] == REQUEST_SENSE) {
i = srb->cmnd[4];
if (i > sizeof info->sense_data)
i = sizeof info->sense_data;
US_DEBUGP("SDDR55: request sense %02x/%02x/%02x\n", info->sense_data[2], info->sense_data[12], info->sense_data[13]);
info->sense_data[0] = 0x70;
info->sense_data[7] = 10;
memcpy (ptr, info->sense_data, i);
memset (info->sense_data, 0, sizeof info->sense_data);
return USB_STOR_TRANSPORT_GOOD;
}
memset (info->sense_data, 0, sizeof info->sense_data);
/* Dummy up a response for INQUIRY since SDDR55 doesn't
respond to INQUIRY commands */
if (srb->cmnd[0] == INQUIRY) {
memset(inquiry_response+8, 0, 28);
fill_inquiry_response(us, inquiry_response, 36);
return USB_STOR_TRANSPORT_GOOD;
}
/* only check card status if the map isn't allocated, ie no card seen yet
* or if it's been over half a second since we last accessed it
*/
if (info->lba_to_pba == NULL || time_after(jiffies, info->last_access + HZ/2)) {
/* check to see if a card is fitted */
result = sddr55_status (us);
if (result) {
result = sddr55_status (us);
if (!result) {
set_sense_info (6, 0x28, 0); /* new media, set unit attention, not ready to ready */
}
return USB_STOR_TRANSPORT_FAILED;
}
}
/* if we detected a problem with the map when writing, don't allow any more access */
if (info->fatal_error) {
set_sense_info (3, 0x31, 0);
return USB_STOR_TRANSPORT_FAILED;
}
if (srb->cmnd[0] == READ_CAPACITY) {
capacity = sddr55_get_capacity(us);
if (!capacity) {
set_sense_info (3, 0x30, 0); /* incompatible medium */
return USB_STOR_TRANSPORT_FAILED;
}
info->capacity = capacity;
/* figure out the maximum logical block number, allowing for the fact
* that only 250 out of every 256 are used */
info->max_log_blks = ((info->capacity >> (info->pageshift + info->blockshift)) / 256) * 250;
/* Last page in the card, adjust as we only use 250 out of every 256 pages */
capacity = (capacity / 256) * 250;
capacity /= PAGESIZE;
capacity--;
ptr[0] = MSB_of(capacity>>16);
ptr[1] = LSB_of(capacity>>16);
ptr[2] = MSB_of(capacity&0xFFFF);
ptr[3] = LSB_of(capacity&0xFFFF);
// The page size
ptr[4] = MSB_of(PAGESIZE>>16);
ptr[5] = LSB_of(PAGESIZE>>16);
ptr[6] = MSB_of(PAGESIZE&0xFFFF);
ptr[7] = LSB_of(PAGESIZE&0xFFFF);
sddr55_read_map(us);
return USB_STOR_TRANSPORT_GOOD;
}
static int usb_stor_control_thread(void * __us)
{
struct us_data *us = (struct us_data *)__us;
struct Scsi_Host *host = us_to_host(us);
//---------------------------
pr_info("7 usb stor control thread\n");
for(;;) {
//若有u盘拔插或者有命令才会awake，否则一直就在这睡觉觉
if (wait_for_completion_interruptible(&us->cmnd_ready))
break;
//从此处wake
/* */
mutex_lock(&(us->dev_mutex));
/*每当需要写us->srb时候就需要锁之 */
scsi_lock(host);
if (us->srb == NULL) {
scsi_unlock(host);
mutex_unlock(&us->dev_mutex);
US_DEBUGP("-- exiting\n");
break;
}
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
us->srb->result = DID_ABORT << 16;
goto SkipForAbort;
}
scsi_unlock(host);
if (us->srb->sc_data_direction == DMA_BIDIRECTIONAL) {
US_DEBUGP("UNKNOWN data direction\n");
us->srb->result = DID_ERROR << 16;
}
else if (us->srb->device->id &&
!(us->fflags & US_FL_SCM_MULT_TARG)) {
US_DEBUGP("Bad target number (%d:%d)\n",
us->srb->device->id, us->srb->device->lun);
us->srb->result = DID_BAD_TARGET << 16;
}
else if (us->srb->device->lun > us->max_lun) {
US_DEBUGP("Bad LUN (%d:%d)\n",
us->srb->device->id, us->srb->device->lun);
us->srb->result = DID_BAD_TARGET << 16;
}
else if ((us->srb->cmnd[0] == INQUIRY) &&
(us->fflags & US_FL_FIX_INQUIRY)) {
unsigned char data_ptr[36] = {
0x00, 0x80, 0x02, 0x02,
0x1F, 0x00, 0x00, 0x00};
US_DEBUGP("Faking INQUIRY command\n");
fill_inquiry_response(us, data_ptr, 36);
us->srb->result = SAM_STAT_GOOD;
}
else {
US_DEBUG(usb_stor_show_command(us->srb));
us->proto_handler(us->srb, us);
usb_mark_last_busy(us->pusb_dev);
}
scsi_lock(host);
if (us->srb->result != DID_ABORT << 16) {
US_DEBUGP("scsi cmd done, result=0x%x\n",
us->srb->result);
us->srb->scsi_done(us->srb);
} else {
SkipForAbort:
US_DEBUGP("scsi command aborted\n");
}
/* */
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
complete(&(us->notify));
clear_bit(US_FLIDX_ABORTING, &us->dflags);
clear_bit(US_FLIDX_TIMED_OUT, &us->dflags);
}
us->srb = NULL;
scsi_unlock(host);
/
mutex_unlock(&us->dev_mutex);
}
//仔细研读
static int usb_stor_control_thread(void * __us)
{
struct us_data *us = (struct us_data *)__us;
struct Scsi_Host *host = us_to_host(us);
//---------------------------
pr_info("7 usb stor control thread\n");
for(;;) {
US_DEBUGP("*** thread sleeping.\n");
if (wait_for_completion_interruptible(&us->cmnd_ready))
break;
US_DEBUGP("*** thread awakened.\n");
/* lock the device pointers */
mutex_lock(&(us->dev_mutex));
/* lock access to the state */
scsi_lock(host);
/* When we are called with no command pending, we're done */
if (us->srb == NULL) {
scsi_unlock(host);
mutex_unlock(&us->dev_mutex);
US_DEBUGP("-- exiting\n");
break;
}
/* has the command timed out *already* ? */
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
us->srb->result = DID_ABORT << 16;
goto SkipForAbort;
}
scsi_unlock(host);
/* reject the command if the direction indicator
* is UNKNOWN
*/
if (us->srb->sc_data_direction == DMA_BIDIRECTIONAL) {
US_DEBUGP("UNKNOWN data direction\n");
us->srb->result = DID_ERROR << 16;
}
/* reject if target != 0 or if LUN is higher than
* the maximum known LUN
*/
else if (us->srb->device->id &&
!(us->fflags & US_FL_SCM_MULT_TARG)) {
US_DEBUGP("Bad target number (%d:%d)\n",
us->srb->device->id, us->srb->device->lun);
us->srb->result = DID_BAD_TARGET << 16;
}
else if (us->srb->device->lun > us->max_lun) {
US_DEBUGP("Bad LUN (%d:%d)\n",
us->srb->device->id, us->srb->device->lun);
us->srb->result = DID_BAD_TARGET << 16;
}
/* Handle those devices which need us to fake
* their inquiry data */
else if ((us->srb->cmnd[0] == INQUIRY) &&
(us->fflags & US_FL_FIX_INQUIRY)) {
unsigned char data_ptr[36] = {
0x00, 0x80, 0x02, 0x02,
0x1F, 0x00, 0x00, 0x00};
US_DEBUGP("Faking INQUIRY command\n");
fill_inquiry_response(us, data_ptr, 36);
us->srb->result = SAM_STAT_GOOD;
}
/* we've got a command, let's do it! */
else {
US_DEBUG(usb_stor_show_command(us->srb));
us->proto_handler(us->srb, us);
usb_mark_last_busy(us->pusb_dev);
}
/* lock access to the state */
scsi_lock(host);
/* indicate that the command is done */
if (us->srb->result != DID_ABORT << 16) {
US_DEBUGP("scsi cmd done, result=0x%x\n",
us->srb->result);
us->srb->scsi_done(us->srb);
} else {
SkipForAbort:
US_DEBUGP("scsi command aborted\n");
}
/* If an abort request was received we need to signal that
* the abort has finished. The proper test for this is
* the TIMED_OUT flag, not srb->result == DID_ABORT, because
* the timeout might have occurred after the command had
* already completed with a different result code. */
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
complete(&(us->notify));
/* Allow USB transfers to resume */
clear_bit(US_FLIDX_ABORTING, &us->dflags);
clear_bit(US_FLIDX_TIMED_OUT, &us->dflags);
}
/* finished working on this command */
us->srb = NULL;
scsi_unlock(host);
/* unlock the device pointers */
mutex_unlock(&us->dev_mutex);
} /* for (;;) */
/* Wait until we are told to stop */
for (;;) {
set_current_state(TASK_INTERRUPTIBLE);
if (kthread_should_stop())
break;
schedule();
}
__set_current_state(TASK_RUNNING);
return 0;
}
/*
* Transport for the Sandisk SDDR-55
*/
static int sddr55_transport(struct scsi_cmnd *srb, struct us_data *us)
{
int result;
static unsigned char inquiry_response[8] = {
0x00, 0x80, 0x00, 0x02, 0x1F, 0x00, 0x00, 0x00
};
// write-protected for now, no block descriptor support
static unsigned char mode_page_01[20] = {
0x0, 0x12, 0x00, 0x80, 0x0, 0x0, 0x0, 0x0,
0x01, 0x0A,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
};
unsigned char *ptr = us->iobuf;
unsigned long capacity;
unsigned int lba;
unsigned int pba;
unsigned int page;
unsigned short pages;
struct sddr55_card_info *info;
if (!us->extra) {
us->extra = kzalloc(
sizeof(struct sddr55_card_info), GFP_NOIO);
if (!us->extra)
return USB_STOR_TRANSPORT_ERROR;
us->extra_destructor = sddr55_card_info_destructor;
}
info = (struct sddr55_card_info *)(us->extra);
if (srb->cmnd[0] == REQUEST_SENSE) {
usb_stor_dbg(us, "request sense %02x/%02x/%02x\n",
info->sense_data[2],
info->sense_data[12],
info->sense_data[13]);
memcpy (ptr, info->sense_data, sizeof info->sense_data);
ptr[0] = 0x70;
ptr[7] = 11;
usb_stor_set_xfer_buf (ptr, sizeof info->sense_data, srb);
memset (info->sense_data, 0, sizeof info->sense_data);
return USB_STOR_TRANSPORT_GOOD;
}
memset (info->sense_data, 0, sizeof info->sense_data);
/*
* Dummy up a response for INQUIRY since SDDR55 doesn't
* respond to INQUIRY commands
*/
if (srb->cmnd[0] == INQUIRY) {
memcpy(ptr, inquiry_response, 8);
fill_inquiry_response(us, ptr, 36);
return USB_STOR_TRANSPORT_GOOD;
}
/*
* only check card status if the map isn't allocated, ie no card seen yet
* or if it's been over half a second since we last accessed it
*/
if (info->lba_to_pba == NULL || time_after(jiffies, info->last_access + HZ/2)) {
/* check to see if a card is fitted */
result = sddr55_status (us);
if (result) {
result = sddr55_status (us);
if (!result) {
set_sense_info (6, 0x28, 0); /* new media, set unit attention, not ready to ready */
}
return USB_STOR_TRANSPORT_FAILED;
}
}
/*
* if we detected a problem with the map when writing,
* don't allow any more access
*/
if (info->fatal_error) {
set_sense_info (3, 0x31, 0);
return USB_STOR_TRANSPORT_FAILED;
}
if (srb->cmnd[0] == READ_CAPACITY) {
capacity = sddr55_get_capacity(us);
if (!capacity) {
set_sense_info (3, 0x30, 0); /* incompatible medium */
return USB_STOR_TRANSPORT_FAILED;
}
info->capacity = capacity;
/*
* figure out the maximum logical block number, allowing for
* the fact that only 250 out of every 256 are used
*/
info->max_log_blks = ((info->capacity >> (info->pageshift + info->blockshift)) / 256) * 250;
/*
* Last page in the card, adjust as we only use 250 out of
* every 256 pages
*/
capacity = (capacity / 256) * 250;
capacity /= PAGESIZE;
capacity--;
((__be32 *) ptr)[0] = cpu_to_be32(capacity);
((__be32 *) ptr)[1] = cpu_to_be32(PAGESIZE);
usb_stor_set_xfer_buf(ptr, 8, srb);
sddr55_read_map(us);
return USB_STOR_TRANSPORT_GOOD;
}
