/**************************************************************************//** * @brief Main function of example. ******************************************************************************/ void main(void) { uint8_t ui8KeyBm = 0; uint_fast16_t ui16Cnt = 0; uint8_t ui8Byte = APP_TX_BYTE; // // Initialize clocks and board I/O // bspInit(BSP_SYS_CLK_SPD); // // Set LED1 to indicate life // bspLedSet(BSP_LED_1); // // Initialize key driver // bspKeyInit(BSP_KEY_MODE_ISR); bspKeyIntEnable(BSP_KEY_SELECT|BSP_KEY_UP); // // Initialize UART to USB MCU // bspUartBufInit(pui8TxBuf, sizeof(pui8TxBuf), pui8RxBuf, sizeof(pui8RxBuf)); // // Application must register the UART interrupt handler // UARTIntRegister(BSP_UART_BASE, &appUartIsr); // // Open UART connection // if(bspUartOpen(eBaudRate115200) != BSP_UART_SUCCESS) { // // Failed to initialize UART handler // bspAssert(); } // // Initialize SPI interface to LCD, configure LCD, and display information. // bspSpiInit(BSP_SPI_CLK_SPD); lcdInit(); lcdBufferPrintStringAligned(0, "UART example", eLcdAlignCenter, eLcdPage0); lcdBufferInvertPage(0, 0,127, eLcdPage0); lcdBufferPrintString(0, "Baud rate :", 6, eLcdPage2); lcdBufferPrintIntAligned(0, bspUartBaudRateGet(), eLcdAlignRight, eLcdPage2); lcdBufferPrintString(0, "Format :", 6, eLcdPage3); lcdBufferPrintStringAligned(0, "8-N-1", eLcdAlignRight, eLcdPage3); lcdBufferPrintString(0, "Flow control:", 6, eLcdPage4); lcdBufferPrintStringAligned(0, "No", eLcdAlignRight, eLcdPage4); lcdBufferPrintStringAligned(0, "Transmit: UP key", eLcdAlignRight, eLcdPage6); lcdBufferPrintStringAligned(0, "SELECT to toggle mode", eLcdAlignCenter, eLcdPage7); lcdBufferInvertPage(0, 0,127, eLcdPage7); lcdSendBuffer(0); // // Enable global interrupts // IntMasterEnable(); while(1) { ui8KeyBm = bspKeyPushed(BSP_KEY_ALL); if(BSP_KEY_SELECT & ui8KeyBm) { // // Change mode // bRepeaterMode ^= 1; bspLedToggle(BSP_LED_3); // // Update LCD for the new mode // lcdBufferClearPart(0, 0,127, eLcdPage6, eLcdPage6); if(bRepeaterMode) { lcdBufferPrintStringAligned(0, "Repeater mode", eLcdAlignCenter, eLcdPage6); } else { lcdBufferPrintStringAligned(0, "Transmit: UP key", eLcdAlignCenter, eLcdPage6); } lcdSendBufferPart(0, 0,127, eLcdPage6, eLcdPage6); } // // Read data from UART RX buffer to application buffer // ui16Cnt = bspUartDataGet(pui8AppBuf, bspUartRxCharsAvail()); if(bRepeaterMode) { // // Repeater mode // if(ui16Cnt) { // // Send data from application buffer to UART TX buffer // bspUartDataPut(pui8AppBuf, ui16Cnt); } } else { // // Transmit mode // if(BSP_KEY_UP & ui8KeyBm) { // // Transmit a single character // bspUartDataPut(&ui8Byte, 1); } } } }
/***************************************************************************//** * @brief Updates LCD buffer and sends buffer to LCD module * * +-----------------------------------------+ * |_____________ SIGFOX DEMO_______________| * | UL: XX XX XX XX XX XX | * | XX XX XX XX XX XX | * | | * | DL: XX XX XX XX XX XX | * | XX XX | * |_________________________________________| * | (c) Texas Instruments | * +-----------------------------------------+ * *******************************************************************************/ static void updateLCD(void) { char ulmsg[36] = {0}; char dlmsg[24] = {0}; char ulmsg1[18] = {0}; char ulmsg2[18] = {0}; char dlmsg1[18] = {0}; char dlmsg2[6] = {0}; dataToString((unsigned char*) message, ulmsg, 24); dataToString((unsigned char*) ReceivedPayload, dlmsg, 16); // Format the converted string to display on LCD unsigned char n; unsigned char m = 0; for(n=0;n<12;n++) { if(m % 3 == 0) { ulmsg1[m] = ' '; ulmsg2[m] = ' '; dlmsg1[m] = ' '; if(n<4) { dlmsg2[m] = ' '; } m++; } ulmsg1[m] = ulmsg[n]; ulmsg2[m] = ulmsg[12+n]; dlmsg1[m] = dlmsg[n]; if(n<4) { dlmsg2[m] = dlmsg[12+n]; } m++; } // Clear LCD lcdBufferClear(0); lcdSendBuffer(0); // Load status buffer lcdBufferPrintStringAligned(0, "Sigfox Demo", eLcdAlignCenter, eLcdPage0); lcdBufferSetHLine(0, 0, LCD_COLS-1, 7); lcdBufferInvertPage(0, 0, LCD_COLS, eLcdPage0); lcdSendBufferPart(0, 0, 127, eLcdPage0,eLcdPage0); lcdBufferClearPart(0, 0, 127, eLcdPage1, eLcdPage6); lcdBufferPrintString(0, "UL:", 0, eLcdPage1); lcdBufferPrintString(0, ulmsg1, 20, eLcdPage1); lcdSendBufferPart(0, 0, 127, eLcdPage1,eLcdPage1); lcdBufferPrintString(0, ulmsg2, 20, eLcdPage2); lcdSendBufferPart(0, 20, 127, eLcdPage2,eLcdPage2); lcdBufferClearPart(0, 0, 127, eLcdPage3, eLcdPage6); lcdBufferPrintString(0, "DL:", 0, eLcdPage4); lcdBufferPrintString(0, dlmsg1, 20, eLcdPage4); lcdSendBufferPart(0, 0, 127, eLcdPage4,eLcdPage4); lcdBufferPrintString(0, dlmsg2, 20, eLcdPage5); lcdSendBufferPart(0, 20, 55, eLcdPage5,eLcdPage5); lcdBufferPrintString(0, "(c) Texas Instruments" , 0, eLcdPage7); lcdBufferSetHLine(0, 0, LCD_COLS-1, 55); lcdBufferInvertPage(0, 0, LCD_COLS, eLcdPage7); // Send the buffer to the LCD screen lcdSendBufferPart(0, 0, 127, eLcdPage7, eLcdPage7); }