/**
* handle_edge_irq - edge type IRQ handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Interrupt occures on the falling and/or rising edge of a hardware
* signal. The occurrence is latched into the irq controller hardware
* and must be acked in order to be reenabled. After the ack another
* interrupt can happen on the same source even before the first one
* is handled by the associated event handler. If this happens it
* might be necessary to disable (mask) the interrupt depending on the
* controller hardware. This requires to reenable the interrupt inside
* of the loop which handles the interrupts which have arrived while
* the handler was running. If all pending interrupts are handled, the
* loop is left.
*/
void
handle_edge_irq(unsigned int irq, struct irq_desc *desc)
{
raw_spin_lock(&desc->lock);
desc->istate &= ~(IRQS_REPLAY | IRQS_WAITING);
if (!irq_may_run(desc)) {
desc->istate |= IRQS_PENDING;
mask_ack_irq(desc);
goto out_unlock;
}
/*
* If its disabled or no action available then mask it and get
* out of here.
*/
if (irqd_irq_disabled(&desc->irq_data) || !desc->action) {
desc->istate |= IRQS_PENDING;
mask_ack_irq(desc);
goto out_unlock;
}
kstat_incr_irqs_this_cpu(irq, desc);
/* Start handling the irq */
desc->irq_data.chip->irq_ack(&desc->irq_data);
do {
if (unlikely(!desc->action)) {
mask_irq(desc);
goto out_unlock;
}
/*
* When another irq arrived while we were handling
* one, we could have masked the irq.
* Renable it, if it was not disabled in meantime.
*/
if (unlikely(desc->istate & IRQS_PENDING)) {
if (!irqd_irq_disabled(&desc->irq_data) &&
irqd_irq_masked(&desc->irq_data))
unmask_irq(desc);
}
handle_irq_event(desc);
} while ((desc->istate & IRQS_PENDING) &&
!irqd_irq_disabled(&desc->irq_data));
out_unlock:
raw_spin_unlock(&desc->lock);
}
void
__irq_set_handler(unsigned int irq, irq_flow_handler_t handle, int is_chained,
const char *name)
{
unsigned long flags;
struct irq_desc *desc = irq_get_desc_buslock(irq, &flags);
if (!desc)
return;
if (!handle) {
handle = handle_bad_irq;
} else {
if (WARN_ON(desc->irq_data.chip == &no_irq_chip))
goto out;
}
/* Uninstall? */
if (handle == handle_bad_irq) {
if (desc->irq_data.chip != &no_irq_chip)
mask_ack_irq(desc);
irq_state_set_disabled(desc);
desc->depth = 1;
}
desc->handle_irq = handle;
desc->name = name;
if (handle != handle_bad_irq && is_chained) {
irq_settings_set_noprobe(desc);
irq_settings_set_norequest(desc);
irq_startup(desc);
}
out:
irq_put_desc_busunlock(desc, flags);
}
/**
* handle_edge_irq - edge type IRQ handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Interrupt occures on the falling and/or rising edge of a hardware
* signal. The occurence is latched into the irq controller hardware
* and must be acked in order to be reenabled. After the ack another
* interrupt can happen on the same source even before the first one
* is handled by the associated event handler. If this happens it
* might be necessary to disable (mask) the interrupt depending on the
* controller hardware. This requires to reenable the interrupt inside
* of the loop which handles the interrupts which have arrived while
* the handler was running. If all pending interrupts are handled, the
* loop is left.
*/
void
handle_edge_irq(unsigned int irq, struct irq_desc *desc)
{
raw_spin_lock(&desc->lock);
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
/*
* If we're currently running this IRQ, or its disabled,
* we shouldn't process the IRQ. Mark it pending, handle
* the necessary masking and go out
*/
if (unlikely((desc->status & (IRQ_INPROGRESS | IRQ_DISABLED)) ||
!desc->action)) {
desc->status |= (IRQ_PENDING | IRQ_MASKED);
mask_ack_irq(desc, irq);
goto out_unlock;
}
kstat_incr_irqs_this_cpu(irq, desc);
/* Start handling the irq */
if (desc->chip->ack)
desc->chip->ack(irq);
/* Mark the IRQ currently in progress.*/
desc->status |= IRQ_INPROGRESS;
do {
struct irqaction *action = desc->action;
irqreturn_t action_ret;
if (unlikely(!action)) {
mask_irq(desc, irq);
goto out_unlock;
}
/*
* When another irq arrived while we were handling
* one, we could have masked the irq.
* Renable it, if it was not disabled in meantime.
*/
if (unlikely((desc->status &
(IRQ_PENDING | IRQ_MASKED | IRQ_DISABLED)) ==
(IRQ_PENDING | IRQ_MASKED))) {
unmask_irq(desc, irq);
}
desc->status &= ~IRQ_PENDING;
raw_spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
raw_spin_lock(&desc->lock);
} while ((desc->status & (IRQ_PENDING | IRQ_DISABLED)) == IRQ_PENDING);
desc->status &= ~IRQ_INPROGRESS;
out_unlock:
raw_spin_unlock(&desc->lock);
}
/**
* handle_level_irq - Level type irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Level type interrupts are active as long as the hardware line has
* the active level. This may require to mask the interrupt and unmask
* it after the associated handler has acknowledged the device, so the
* interrupt line is back to inactive.
*/
void
handle_level_irq(unsigned int irq, struct irq_desc *desc)
{
raw_spin_lock(&desc->lock);
mask_ack_irq(desc);
if (unlikely(desc->istate & IRQS_INPROGRESS))
if (!irq_check_poll(desc))
goto out_unlock;
desc->istate &= ~(IRQS_REPLAY | IRQS_WAITING);
kstat_incr_irqs_this_cpu(irq, desc);
/*
* If its disabled or no action available
* keep it masked and get out of here
*/
if (unlikely(!desc->action || (desc->istate & IRQS_DISABLED)))
goto out_unlock;
handle_irq_event(desc);
if (!(desc->istate & (IRQS_DISABLED | IRQS_ONESHOT)))
unmask_irq(desc);
out_unlock:
raw_spin_unlock(&desc->lock);
}
/**
* handle_level_irq - Level type irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Level type interrupts are active as long as the hardware line has
* the active level. This may require to mask the interrupt and unmask
* it after the associated handler has acknowledged the device, so the
* interrupt line is back to inactive.
*/
void
handle_level_irq(unsigned int irq, struct irq_desc *desc)
{
raw_spin_lock(&desc->lock);
mask_ack_irq(desc);
if (unlikely(irqd_irq_inprogress(&desc->irq_data)))
if (!irq_check_poll(desc))
goto out_unlock;
desc->istate &= ~(IRQS_REPLAY | IRQS_WAITING);
kstat_incr_irqs_this_cpu(irq, desc);
/*
* If its disabled or no action available
* keep it masked and get out of here
*/
if (unlikely(!desc->action || irqd_irq_disabled(&desc->irq_data))) {
desc->istate |= IRQS_PENDING;
goto out_unlock;
}
handle_irq_event(desc);
cond_unmask_irq(desc);
out_unlock:
raw_spin_unlock(&desc->lock);
}
void
__irq_set_handler(unsigned int irq, irq_flow_handler_t handle, int is_chained,
const char *name)
{
unsigned long flags;
struct irq_desc *desc = irq_get_desc_buslock(irq, &flags, 0);
if (!desc)
return;
if (!handle) {
handle = handle_bad_irq;
} else {
struct irq_data *irq_data = &desc->irq_data;
#ifdef CONFIG_IRQ_DOMAIN_HIERARCHY
/*
* With hierarchical domains we might run into a
* situation where the outermost chip is not yet set
* up, but the inner chips are there. Instead of
* bailing we install the handler, but obviously we
* cannot enable/startup the interrupt at this point.
*/
while (irq_data) {
if (irq_data->chip != &no_irq_chip)
break;
/*
* Bail out if the outer chip is not set up
* and the interrrupt supposed to be started
* right away.
*/
if (WARN_ON(is_chained))
goto out;
/* Try the parent */
irq_data = irq_data->parent_data;
}
#endif
if (WARN_ON(!irq_data || irq_data->chip == &no_irq_chip))
goto out;
}
/* Uninstall? */
if (handle == handle_bad_irq) {
if (desc->irq_data.chip != &no_irq_chip)
mask_ack_irq(desc);
irq_state_set_disabled(desc);
desc->depth = 1;
}
desc->handle_irq = handle;
desc->name = name;
if (handle != handle_bad_irq && is_chained) {
irq_settings_set_noprobe(desc);
irq_settings_set_norequest(desc);
irq_settings_set_nothread(desc);
irq_startup(desc, true);
}
out:
irq_put_desc_busunlock(desc, flags);
}
/**
* handle_level_irq - Level type irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Level type interrupts are active as long as the hardware line has
* the active level. This may require to mask the interrupt and unmask
* it after the associated handler has acknowledged the device, so the
* interrupt line is back to inactive.
*/
void
handle_level_irq(unsigned int irq, struct irq_desc *desc)
{
struct irqaction *action;
irqreturn_t action_ret;
spin_lock(&desc->lock);
/*
调用中断线所属的中断控制的mask_ack函数.
如果没有定义该函数，就调用mask，然后调用ack函数.
总之，对于水平触发的来说，它就是屏蔽当前的中断线，应当当前中断..
比如ARM来说，就是清除SRCPND、SRCINTPND寄存器的位.
*/
mask_ack_irq(desc, irq);
desc = irq_remap_to_desc(irq, desc);
/*
在多处理器的系统上，可能中断已经被另外一个CPU开始处理..但是该CPU也
进入到进入处理..此时另外处理的CPU会设置状态为正在处理当中..
因此，当前CPU就直接退出。
*/
if (unlikely(desc->status & IRQ_INPROGRESS))
goto out_unlock;
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
kstat_incr_irqs_this_cpu(irq, desc);
/*
* If its disabled or no action available
* keep it masked and get out of here
*/
action = desc->action;
/*
如果该中断线上没有中断处理函数，那就直接退出.
或者说，该中断线当前状态是DISABLED，也就是要屏蔽掉该中断的..?
但是由于某种原因还产生了中断?不过确实状态就是DISABLED，那也直接退出。
*/
if (unlikely(!action || (desc->status & IRQ_DISABLED)))
goto out_unlock;
//好这里设置为正在处理当中...避免多处理的竞争...哦。这断代码的执行
//是在上锁的状态下的..下面解锁.
desc->status |= IRQ_INPROGRESS;
spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
spin_lock(&desc->lock);
//处理完成之后..这里要修改当前中断线的状态了..一样是上锁.
desc->status &= ~IRQ_INPROGRESS;
//该中断线的状态是不屏蔽的，并且有unmask函数..那就调用unmask，它就是
//取消屏蔽该中断线...因为水平电流处理函数在一开始有mask_ack_irq给屏蔽掉了中断线了
if (!(desc->status & IRQ_DISABLED) && desc->chip->unmask)
desc->chip->unmask(irq);
out_unlock:
spin_unlock(&desc->lock);
}
/**
* handle_edge_irq - edge type IRQ handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Interrupt occures on the falling and/or rising edge of a hardware
* signal. The occurrence is latched into the irq controller hardware
* and must be acked in order to be reenabled. After the ack another
* interrupt can happen on the same source even before the first one
* is handled by the associated event handler. If this happens it
* might be necessary to disable (mask) the interrupt depending on the
* controller hardware. This requires to reenable the interrupt inside
* of the loop which handles the interrupts which have arrived while
* the handler was running. If all pending interrupts are handled, the
* loop is left.
*/
bool
handle_edge_irq(unsigned int irq, struct irq_desc *desc)
{
bool handled = false;
raw_spin_lock(&desc->lock);
desc->istate &= ~(IRQS_REPLAY | IRQS_WAITING);
/*
* If we're currently running this IRQ, or its disabled,
* we shouldn't process the IRQ. Mark it pending, handle
* the necessary masking and go out
*/
if (unlikely(irqd_irq_disabled(&desc->irq_data) ||
irqd_irq_inprogress(&desc->irq_data) || !desc->action)) {
if (!irq_check_poll(desc)) {
desc->istate |= IRQS_PENDING;
mask_ack_irq(desc);
goto out_unlock;
}
}
kstat_incr_irqs_this_cpu(irq, desc);
/* Start handling the irq */
desc->irq_data.chip->irq_ack(&desc->irq_data);
do {
if (unlikely(!desc->action)) {
mask_irq(desc);
goto out_unlock;
}
/*
* When another irq arrived while we were handling
* one, we could have masked the irq.
* Renable it, if it was not disabled in meantime.
*/
if (unlikely(desc->istate & IRQS_PENDING)) {
if (!irqd_irq_disabled(&desc->irq_data) &&
irqd_irq_masked(&desc->irq_data))
unmask_irq(desc);
}
handle_irq_event(desc);
handled = true;
} while ((desc->istate & IRQS_PENDING) &&
!irqd_irq_disabled(&desc->irq_data));
out_unlock:
raw_spin_unlock(&desc->lock);
return handled;
}
void
__set_irq_handler(unsigned int irq, irq_flow_handler_t handle, int is_chained,
const char *name)
{
struct irq_desc *desc = irq_to_desc(irq);
unsigned long flags;
if (!desc) {
printk(KERN_ERR
"Trying to install type control for IRQ%d\n", irq);
return;
}
if (!handle)
handle = handle_bad_irq;
else if (desc->irq_data.chip == &no_irq_chip) {
printk(KERN_WARNING "Trying to install %sinterrupt handler "
"for IRQ%d\n", is_chained ? "chained " : "", irq);
/*
* Some ARM implementations install a handler for really dumb
* interrupt hardware without setting an irq_chip. This worked
* with the ARM no_irq_chip but the check in setup_irq would
* prevent us to setup the interrupt at all. Switch it to
* dummy_irq_chip for easy transition.
*/
desc->irq_data.chip = &dummy_irq_chip;
}
chip_bus_lock(desc);
raw_spin_lock_irqsave(&desc->lock, flags);
handle = __fixup_irq_handler(desc, handle, is_chained);
/* Uninstall? */
if (handle == handle_bad_irq) {
if (desc->irq_data.chip != &no_irq_chip)
mask_ack_irq(desc);
desc->status |= IRQ_DISABLED;
desc->depth = 1;
}
desc->handle_irq = handle;
desc->name = name;
if (handle != handle_bad_irq && is_chained) {
desc->status &= ~IRQ_DISABLED;
desc->status |= IRQ_NOREQUEST | IRQ_NOPROBE;
desc->depth = 0;
desc->irq_data.chip->irq_startup(&desc->irq_data);
}
raw_spin_unlock_irqrestore(&desc->lock, flags);
chip_bus_sync_unlock(desc);
}
/**
* handle_edge_irq - edge type IRQ handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Interrupt occures on the falling and/or rising edge of a hardware
* signal. The occurence is latched into the irq controller hardware
* and must be acked in order to be reenabled. After the ack another
* interrupt can happen on the same source even before the first one
* is handled by the associated event handler. If this happens it
* might be necessary to disable (mask) the interrupt depending on the
* controller hardware. This requires to reenable the interrupt inside
* of the loop which handles the interrupts which have arrived while
* the handler was running. If all pending interrupts are handled, the
* loop is left.
*/
void
handle_edge_irq(unsigned int irq, struct irq_desc *desc)
{
raw_spin_lock(&desc->lock);
desc->istate &= ~(IRQS_REPLAY | IRQS_WAITING);
/*
* If we're currently running this IRQ, or its disabled,
* we shouldn't process the IRQ. Mark it pending, handle
* the necessary masking and go out
*/
if (unlikely((desc->istate & (IRQS_DISABLED | IRQS_INPROGRESS) ||
!desc->action))) {
if (!irq_check_poll(desc)) {
irq_compat_set_pending(desc);
desc->istate |= IRQS_PENDING;
mask_ack_irq(desc);
goto out_unlock;
}
}
kstat_incr_irqs_this_cpu(irq, desc);
/* Start handling the irq */
desc->irq_data.chip->irq_ack(&desc->irq_data);
do {
if (unlikely(!desc->action)) {
mask_irq(desc);
goto out_unlock;
}
/*
* When another irq arrived while we were handling
* one, we could have masked the irq.
* Renable it, if it was not disabled in meantime.
*/
if (unlikely(desc->istate & IRQS_PENDING)) {
if (!(desc->istate & IRQS_DISABLED) &&
(desc->istate & IRQS_MASKED))
unmask_irq(desc);
}
handle_irq_event(desc);
} while ((desc->istate & IRQS_PENDING) &&
!(desc->istate & IRQS_DISABLED));
out_unlock:
raw_spin_unlock(&desc->lock);
}
/**
* handle_level_irq - Level type irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Level type interrupts are active as long as the hardware line has
* the active level. This may require to mask the interrupt and unmask
* it after the associated handler has acknowledged the device, so the
* interrupt line is back to inactive.
*/
void
handle_level_irq(unsigned int irq, struct irq_desc *desc)
{
struct irqaction *action;
irqreturn_t action_ret;
spin_lock(&desc->lock);
mask_ack_irq(desc, irq);
if (unlikely(desc->status & IRQ_INPROGRESS))
goto out_unlock;
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
kstat_incr_irqs_this_cpu(irq, desc);
/*
* If its disabled or no action available
* keep it masked and get out of here
*/
action = desc->action;
if (unlikely(!action || (desc->status & IRQ_DISABLED)))
{
printk(KERN_ERR "IRQ %d enter bad status!\n", irq);
goto out_unlock;
}
desc->status |= IRQ_INPROGRESS;
spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
spin_lock(&desc->lock);
desc->status &= ~IRQ_INPROGRESS;
if (unlikely(desc->status & IRQ_ONESHOT))
desc->status |= IRQ_MASKED;
else if (!(desc->status & IRQ_DISABLED) && desc->chip->unmask)
desc->chip->unmask(irq);
out_unlock:
spin_unlock(&desc->lock);
}
/**
* handle_level_irq - Level type irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Level type interrupts are active as long as the hardware line has
* the active level. This may require to mask the interrupt and unmask
* it after the associated handler has acknowledged the device, so the
* interrupt line is back to inactive.
*/
void fastcall
handle_level_irq(unsigned int irq, struct irq_desc *desc)
{
unsigned int cpu = smp_processor_id();
struct irqaction *action;
irqreturn_t action_ret;
spin_lock(&desc->lock);
mask_ack_irq(desc, irq);
if (unlikely(desc->status & IRQ_INPROGRESS))
goto out_unlock;
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
kstat_cpu(cpu).irqs[irq]++;
/*
* If its disabled or no action available
* keep it masked and get out of here
*/
action = desc->action;
if (unlikely(!action || (desc->status & IRQ_DISABLED))) {
desc->status |= IRQ_PENDING;
goto out_unlock;
}
desc->status |= IRQ_INPROGRESS;
desc->status &= ~IRQ_PENDING;
spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
spin_lock(&desc->lock);
desc->status &= ~IRQ_INPROGRESS;
if (!(desc->status & IRQ_DISABLED) && desc->chip->unmask)
desc->chip->unmask(irq);
out_unlock:
spin_unlock(&desc->lock);
}
void handle_level_irq(unsigned int irq, struct irq_desc *desc)
{
raw_spin_lock(&desc->lock);
mask_ack_irq(desc);
if (irqd_irq_inprogress(&desc->irq_data))
if (!irq_check_poll(desc))
goto out_unlock;
desc->istate &= ~(IRQS_REPLAY | IRQS_WAITING);
/* kstat_incr_irqs_this_cpu(irq, desc); */
if (!desc->action || irqd_irq_disabled(&desc->irq_data))
goto out_unlock;
handle_irq_event(desc);
if (!irqd_irq_disabled(&desc->irq_data) && !(desc->istate & IRQS_ONESHOT))
unmask_irq(desc);
out_unlock:
raw_spin_unlock(&desc->lock);
}
void
handle_edge_irq(unsigned int irq, struct irq_desc *desc)
{
raw_spin_lock(&desc->lock);
desc->istate &= ~(IRQS_REPLAY | IRQS_WAITING);
if (unlikely(irqd_irq_disabled(&desc->irq_data) ||
irqd_irq_inprogress(&desc->irq_data) || !desc->action)) {
if (!irq_check_poll(desc)) {
desc->istate |= IRQS_PENDING;
mask_ack_irq(desc);
goto out_unlock;
}
}
kstat_incr_irqs_this_cpu(irq, desc);
desc->irq_data.chip->irq_ack(&desc->irq_data);
do {
if (unlikely(!desc->action)) {
mask_irq(desc);
goto out_unlock;
}
if (unlikely(desc->istate & IRQS_PENDING)) {
if (!irqd_irq_disabled(&desc->irq_data) &&
irqd_irq_masked(&desc->irq_data))
unmask_irq(desc);
}
handle_irq_event(desc);
} while ((desc->istate & IRQS_PENDING) &&
!irqd_irq_disabled(&desc->irq_data));
out_unlock:
raw_spin_unlock(&desc->lock);
}
/**
* handle_level_irq - Level type irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Level type interrupts are active as long as the hardware line has
* the active level. This may require to mask the interrupt and unmask
* it after the associated handler has acknowledged the device, so the
* interrupt line is back to inactive.
*/
void
handle_level_irq(unsigned int irq, struct irq_desc *desc)
{
struct irqaction *action;
irqreturn_t action_ret;
raw_spin_lock(&desc->lock);
#ifndef CONFIG_IPIPE
mask_ack_irq(desc);
#endif
if (unlikely(desc->status & IRQ_INPROGRESS))
goto out_unlock;
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
kstat_incr_irqs_this_cpu(irq, desc);
/*
* If its disabled or no action available
* keep it masked and get out of here
*/
action = desc->action;
if (unlikely(!action || (desc->status & IRQ_DISABLED)))
goto out_unlock;
desc->status |= IRQ_INPROGRESS;
raw_spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
raw_spin_lock(&desc->lock);
desc->status &= ~IRQ_INPROGRESS;
if (!(desc->status & (IRQ_DISABLED | IRQ_ONESHOT)))
unmask_irq(desc);
out_unlock:
raw_spin_unlock(&desc->lock);
}
/**
* handle_fasteoi_mask_irq - irq handler for level hierarchy
* stacked on transparent controllers
*
* @desc: the interrupt description structure for this irq
*
* Like handle_fasteoi_irq(), but for use with hierarchy where
* the irq_chip also needs to have its ->irq_mask_ack() function
* called.
*/
void handle_fasteoi_mask_irq(struct irq_desc *desc)
{
struct irq_chip *chip = desc->irq_data.chip;
raw_spin_lock(&desc->lock);
mask_ack_irq(desc);
if (!irq_may_run(desc))
goto out;
desc->istate &= ~(IRQS_REPLAY | IRQS_WAITING);
/*
* If its disabled or no action available
* then mask it and get out of here:
*/
if (unlikely(!desc->action || irqd_irq_disabled(&desc->irq_data))) {
desc->istate |= IRQS_PENDING;
mask_irq(desc);
goto out;
}
kstat_incr_irqs_this_cpu(desc);
if (desc->istate & IRQS_ONESHOT)
mask_irq(desc);
preflow_handler(desc);
handle_irq_event(desc);
cond_unmask_eoi_irq(desc, chip);
raw_spin_unlock(&desc->lock);
return;
out:
if (!(chip->flags & IRQCHIP_EOI_IF_HANDLED))
chip->irq_eoi(&desc->irq_data);
raw_spin_unlock(&desc->lock);
}
/**
* handle_edge_irq - edge type IRQ handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Interrupt occures on the falling and/or rising edge of a hardware
* signal. The occurence is latched into the irq controller hardware
* and must be acked in order to be reenabled. After the ack another
* interrupt can happen on the same source even before the first one
* is handled by the assosiacted event handler. If this happens it
* might be necessary to disable (mask) the interrupt depending on the
* controller hardware. This requires to reenable the interrupt inside
* of the loop which handles the interrupts which have arrived while
* the handler was running. If all pending interrupts are handled, the
* loop is left.
*/
void
handle_edge_irq(unsigned int irq, struct irq_desc *desc)
{
spin_lock(&desc->lock);
/*
需要同水平电流处理函数对比，这里并没有调用mask_ack函数，来屏蔽中断线.
*/
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
/*
* If we're currently running this IRQ, or its disabled,
* we shouldn't process the IRQ. Mark it pending, handle
* the necessary masking and go out
*/
/*
如果边缘电平的触发，然后引起了一个中断，处理函数会对该中断线设置为正在处理当中.
也就是IRQ_INPROGRESS标记..此时判断判断IRQ_INPROGRESS如果置位，代表是又一个中断发生了
因为是边缘触发的..那就设置status为PENDING挂机，等待处理.
*/
if (unlikely((desc->status & (IRQ_INPROGRESS | IRQ_DISABLED)) ||
!desc->action)) {
desc->status |= (IRQ_PENDING | IRQ_MASKED);
//已经PENDING了一次处理，这时候特殊处理，屏蔽掉该中断..然后应答该中断线.
//上面status设置为IRQ_MASKED，也可以证实这个情况.
mask_ack_irq(desc, irq);
desc = irq_remap_to_desc(irq, desc);
goto out_unlock;
}
kstat_incr_irqs_this_cpu(irq, desc);
/*
当然..更一般的情况是下面这种...它会调用应答ack.!!注意注意...和水平触发的区别来了.
水平触发是mask_ack!!!
*/
/* Start handling the irq */
if (desc->chip->ack)
desc->chip->ack(irq);
desc = irq_remap_to_desc(irq, desc);
/* Mark the IRQ currently in progress.*/
desc->status |= IRQ_INPROGRESS;
do {
struct irqaction *action = desc->action;
irqreturn_t action_ret;
//如果该中断线没有中断处理函数..那屏蔽掉该中断线..然后退出.
if (unlikely(!action)) {
desc->chip->mask(irq);
goto out_unlock;
}
/*
* When another irq arrived while we were handling
* one, we could have masked the irq.
* Renable it, if it was not disabled in meantime.
*/
if (unlikely((desc->status &
(IRQ_PENDING | IRQ_MASKED | IRQ_DISABLED)) ==
(IRQ_PENDING | IRQ_MASKED))) {
//前面有看到..到中断处理过程中再次引起中断，就会挂机该中断，然后屏蔽中断线.
//此时这里，就是重新设置为不屏蔽的..
desc->chip->unmask(irq);
desc->status &= ~IRQ_MASKED;
}
desc->status &= ~IRQ_PENDING;
spin_unlock(&desc->lock);
//释放锁...进入到处理中断函数中去.
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
//中断处理函数处理完成了...然后还要继续判断在处理过程中是否有新的中断产生.
spin_lock(&desc->lock);
//因为对于边缘触发的中断来说，它的处理过程，可能有引起了中断了的发生了.
//此时会设置status带IRQ_PENDING标记.那就需要在继续执行一遍处理函数.
} while ((desc->status & (IRQ_PENDING | IRQ_DISABLED)) == IRQ_PENDING);
desc->status &= ~IRQ_INPROGRESS;
out_unlock:
spin_unlock(&desc->lock);
}
static void
__irq_do_set_handler(struct irq_desc *desc, irq_flow_handler_t handle,
int is_chained, const char *name)
{
if (!handle) {
handle = handle_bad_irq;
} else {
struct irq_data *irq_data = &desc->irq_data;
#ifdef CONFIG_IRQ_DOMAIN_HIERARCHY
/*
* With hierarchical domains we might run into a
* situation where the outermost chip is not yet set
* up, but the inner chips are there. Instead of
* bailing we install the handler, but obviously we
* cannot enable/startup the interrupt at this point.
*/
while (irq_data) {
if (irq_data->chip != &no_irq_chip)
break;
/*
* Bail out if the outer chip is not set up
* and the interrrupt supposed to be started
* right away.
*/
if (WARN_ON(is_chained))
return;
/* Try the parent */
irq_data = irq_data->parent_data;
}
#endif
if (WARN_ON(!irq_data || irq_data->chip == &no_irq_chip))
return;
}
/* Uninstall? */
if (handle == handle_bad_irq) {
if (desc->irq_data.chip != &no_irq_chip)
mask_ack_irq(desc);
irq_state_set_disabled(desc);
if (is_chained)
desc->action = NULL;
desc->depth = 1;
}
desc->handle_irq = handle;
desc->name = name;
if (handle != handle_bad_irq && is_chained) {
unsigned int type = irqd_get_trigger_type(&desc->irq_data);
/*
* We're about to start this interrupt immediately,
* hence the need to set the trigger configuration.
* But the .set_type callback may have overridden the
* flow handler, ignoring that we're dealing with a
* chained interrupt. Reset it immediately because we
* do know better.
*/
if (type != IRQ_TYPE_NONE) {
__irq_set_trigger(desc, type);
desc->handle_irq = handle;
}
irq_settings_set_noprobe(desc);
irq_settings_set_norequest(desc);
irq_settings_set_nothread(desc);
desc->action = &chained_action;
irq_activate_and_startup(desc, IRQ_RESEND);
}
}
void __ipipe_ack_level_irq(unsigned irq, struct irq_desc *desc)
{
mask_ack_irq(desc);
}
