static void mlx4_en_activate(struct mlx4_dev *dev, void *ctx)
{
int i;
struct mlx4_en_dev *mdev = ctx;
/* Create a netdev for each port */
mlx4_foreach_port(i, dev, MLX4_PORT_TYPE_ETH) {
mlx4_info(mdev, "Activating port:%d\n", i);
if (mlx4_en_init_netdev(mdev, i, &mdev->profile.prof[i]))
mdev->pndev[i] = NULL;
}
static void *mlx4_en_add(struct mlx4_dev *dev)
{
struct mlx4_en_dev *mdev;
int i;
printk_once(KERN_INFO "%s", mlx4_en_version);
mdev = kzalloc(sizeof(*mdev), GFP_KERNEL);
if (!mdev)
goto err_free_res;
if (mlx4_pd_alloc(dev, &mdev->priv_pdn))
goto err_free_dev;
if (mlx4_uar_alloc(dev, &mdev->priv_uar))
goto err_pd;
mdev->uar_map = ioremap((phys_addr_t) mdev->priv_uar.pfn << PAGE_SHIFT,
PAGE_SIZE);
if (!mdev->uar_map)
goto err_uar;
spin_lock_init(&mdev->uar_lock);
mdev->dev = dev;
mdev->dma_device = &dev->persist->pdev->dev;
mdev->pdev = dev->persist->pdev;
mdev->device_up = false;
mdev->LSO_support = !!(dev->caps.flags & (1 << 15));
if (!mdev->LSO_support)
mlx4_warn(mdev, "LSO not supported, please upgrade to later FW version to enable LSO\n");
if (mlx4_mr_alloc(mdev->dev, mdev->priv_pdn, 0, ~0ull,
MLX4_PERM_LOCAL_WRITE | MLX4_PERM_LOCAL_READ,
0, 0, &mdev->mr)) {
mlx4_err(mdev, "Failed allocating memory region\n");
goto err_map;
}
if (mlx4_mr_enable(mdev->dev, &mdev->mr)) {
mlx4_err(mdev, "Failed enabling memory region\n");
goto err_mr;
}
/* Build device profile according to supplied module parameters */
if (mlx4_en_get_profile(mdev)) {
mlx4_err(mdev, "Bad module parameters, aborting\n");
goto err_mr;
}
/* Configure which ports to start according to module parameters */
mdev->port_cnt = 0;
mlx4_foreach_port(i, dev, MLX4_PORT_TYPE_ETH)
mdev->port_cnt++;
/* Initialize time stamp mechanism */
if (mdev->dev->caps.flags2 & MLX4_DEV_CAP_FLAG2_TS)
mlx4_en_init_timestamp(mdev);
/* Set default number of RX rings*/
mlx4_en_set_num_rx_rings(mdev);
/* Create our own workqueue for reset/multicast tasks
* Note: we cannot use the shared workqueue because of deadlocks caused
* by the rtnl lock */
mdev->workqueue = create_singlethread_workqueue("mlx4_en");
if (!mdev->workqueue)
goto err_mr;
/* At this stage all non-port specific tasks are complete:
* mark the card state as up */
mutex_init(&mdev->state_lock);
mdev->device_up = true;
/* Setup ports */
/* Create a netdev for each port */
mlx4_foreach_port(i, dev, MLX4_PORT_TYPE_ETH) {
mlx4_info(mdev, "Activating port:%d\n", i);
if (mlx4_en_init_netdev(mdev, i, &mdev->profile.prof[i]))
mdev->pndev[i] = NULL;
}