/*
* This function resets the connection state.
*
* The function is invoked after receiving a disconnect event from firmware,
* and performs the following actions -
* - Set media status to disconnected
* - Clean up Tx and Rx packets
* - Resets SNR/NF/RSSI value in driver
* - Resets security configurations in driver
* - Enables auto data rate
* - Saves the previous SSID and BSSID so that they can
* be used for re-association, if required
* - Erases current SSID and BSSID information
* - Sends a disconnect event to upper layers/applications.
*/
void mwifiex_reset_connect_state(struct mwifiex_private *priv, u16 reason_code,
bool from_ap)
{
struct mwifiex_adapter *adapter = priv->adapter;
if (!priv->media_connected)
return;
mwifiex_dbg(adapter, INFO,
"info: handles disconnect event\n");
priv->media_connected = false;
priv->scan_block = false;
priv->port_open = false;
if ((GET_BSS_ROLE(priv) == MWIFIEX_BSS_ROLE_STA) &&
ISSUPP_TDLS_ENABLED(priv->adapter->fw_cap_info)) {
mwifiex_disable_all_tdls_links(priv);
if (priv->adapter->auto_tdls)
mwifiex_clean_auto_tdls(priv);
}
/* Free Tx and Rx packets, report disconnect to upper layer */
mwifiex_clean_txrx(priv);
/* Reset SNR/NF/RSSI values */
priv->data_rssi_last = 0;
priv->data_nf_last = 0;
priv->data_rssi_avg = 0;
priv->data_nf_avg = 0;
priv->bcn_rssi_last = 0;
priv->bcn_nf_last = 0;
priv->bcn_rssi_avg = 0;
priv->bcn_nf_avg = 0;
priv->rxpd_rate = 0;
priv->rxpd_htinfo = 0;
priv->sec_info.wpa_enabled = false;
priv->sec_info.wpa2_enabled = false;
priv->wpa_ie_len = 0;
priv->sec_info.wapi_enabled = false;
priv->wapi_ie_len = 0;
priv->sec_info.wapi_key_on = false;
priv->sec_info.encryption_mode = 0;
/* Enable auto data rate */
priv->is_data_rate_auto = true;
priv->data_rate = 0;
priv->assoc_resp_ht_param = 0;
priv->ht_param_present = false;
if ((GET_BSS_ROLE(priv) == MWIFIEX_BSS_ROLE_STA ||
GET_BSS_ROLE(priv) == MWIFIEX_BSS_ROLE_UAP) && priv->hist_data)
mwifiex_hist_data_reset(priv);
if (priv->bss_mode == NL80211_IFTYPE_ADHOC) {
priv->adhoc_state = ADHOC_IDLE;
priv->adhoc_is_link_sensed = false;
}
/*
* Memorize the previous SSID and BSSID so
* it could be used for re-assoc
*/
mwifiex_dbg(adapter, INFO,
"info: previous SSID=%s, SSID len=%u\n",
priv->prev_ssid.ssid, priv->prev_ssid.ssid_len);
mwifiex_dbg(adapter, INFO,
"info: current SSID=%s, SSID len=%u\n",
priv->curr_bss_params.bss_descriptor.ssid.ssid,
priv->curr_bss_params.bss_descriptor.ssid.ssid_len);
memcpy(&priv->prev_ssid,
&priv->curr_bss_params.bss_descriptor.ssid,
sizeof(struct cfg80211_ssid));
memcpy(priv->prev_bssid,
priv->curr_bss_params.bss_descriptor.mac_address, ETH_ALEN);
/* Need to erase the current SSID and BSSID info */
memset(&priv->curr_bss_params, 0x00, sizeof(priv->curr_bss_params));
adapter->tx_lock_flag = false;
adapter->pps_uapsd_mode = false;
if (test_bit(MWIFIEX_IS_CMD_TIMEDOUT, &adapter->work_flags) &&
adapter->curr_cmd)
return;
priv->media_connected = false;
mwifiex_dbg(adapter, MSG,
"info: successfully disconnected from %pM: reason code %d\n",
priv->cfg_bssid, reason_code);
if (priv->bss_mode == NL80211_IFTYPE_STATION ||
priv->bss_mode == NL80211_IFTYPE_P2P_CLIENT) {
cfg80211_disconnected(priv->netdev, reason_code, NULL, 0,
!from_ap, GFP_KERNEL);
}
eth_zero_addr(priv->cfg_bssid);
mwifiex_stop_net_dev_queue(priv->netdev, adapter);
if (netif_carrier_ok(priv->netdev))
netif_carrier_off(priv->netdev);
if (!ISSUPP_FIRMWARE_SUPPLICANT(priv->adapter->fw_cap_info))
return;
mwifiex_send_cmd(priv, HostCmd_CMD_GTK_REKEY_OFFLOAD_CFG,
HostCmd_ACT_GEN_REMOVE, 0, NULL, false);
}
/*
* This function resets the connection state.
*
* The function is invoked after receiving a disconnect event from firmware,
* and performs the following actions -
* - Set media status to disconnected
* - Clean up Tx and Rx packets
* - Resets SNR/NF/RSSI value in driver
* - Resets security configurations in driver
* - Enables auto data rate
* - Saves the previous SSID and BSSID so that they can
* be used for re-association, if required
* - Erases current SSID and BSSID information
* - Sends a disconnect event to upper layers/applications.
*/
void
mwifiex_reset_connect_state(struct mwifiex_private *priv, u16 reason_code)
{
struct mwifiex_adapter *adapter = priv->adapter;
if (!priv->media_connected)
return;
dev_dbg(adapter->dev, "info: handles disconnect event\n");
priv->media_connected = false;
priv->scan_block = false;
if ((GET_BSS_ROLE(priv) == MWIFIEX_BSS_ROLE_STA) &&
ISSUPP_TDLS_ENABLED(priv->adapter->fw_cap_info))
mwifiex_disable_all_tdls_links(priv);
/* Free Tx and Rx packets, report disconnect to upper layer */
mwifiex_clean_txrx(priv);
/* Reset SNR/NF/RSSI values */
priv->data_rssi_last = 0;
priv->data_nf_last = 0;
priv->data_rssi_avg = 0;
priv->data_nf_avg = 0;
priv->bcn_rssi_last = 0;
priv->bcn_nf_last = 0;
priv->bcn_rssi_avg = 0;
priv->bcn_nf_avg = 0;
priv->rxpd_rate = 0;
priv->rxpd_htinfo = 0;
priv->sec_info.wpa_enabled = false;
priv->sec_info.wpa2_enabled = false;
priv->wpa_ie_len = 0;
priv->sec_info.wapi_enabled = false;
priv->wapi_ie_len = 0;
priv->sec_info.wapi_key_on = false;
priv->sec_info.encryption_mode = 0;
/* Enable auto data rate */
priv->is_data_rate_auto = true;
priv->data_rate = 0;
if (priv->bss_mode == NL80211_IFTYPE_ADHOC) {
priv->adhoc_state = ADHOC_IDLE;
priv->adhoc_is_link_sensed = false;
}
/*
* Memorize the previous SSID and BSSID so
* it could be used for re-assoc
*/
dev_dbg(adapter->dev, "info: previous SSID=%s, SSID len=%u\n",
priv->prev_ssid.ssid, priv->prev_ssid.ssid_len);
dev_dbg(adapter->dev, "info: current SSID=%s, SSID len=%u\n",
priv->curr_bss_params.bss_descriptor.ssid.ssid,
priv->curr_bss_params.bss_descriptor.ssid.ssid_len);
memcpy(&priv->prev_ssid,
&priv->curr_bss_params.bss_descriptor.ssid,
sizeof(struct cfg80211_ssid));
memcpy(priv->prev_bssid,
priv->curr_bss_params.bss_descriptor.mac_address, ETH_ALEN);
/* Need to erase the current SSID and BSSID info */
memset(&priv->curr_bss_params, 0x00, sizeof(priv->curr_bss_params));
adapter->tx_lock_flag = false;
adapter->pps_uapsd_mode = false;
if (adapter->is_cmd_timedout && adapter->curr_cmd)
return;
priv->media_connected = false;
dev_dbg(adapter->dev,
"info: successfully disconnected from %pM: reason code %d\n",
priv->cfg_bssid, reason_code);
if (priv->bss_mode == NL80211_IFTYPE_STATION ||
priv->bss_mode == NL80211_IFTYPE_P2P_CLIENT) {
cfg80211_disconnected(priv->netdev, reason_code, NULL, 0,
GFP_KERNEL);
}
memset(priv->cfg_bssid, 0, ETH_ALEN);
mwifiex_stop_net_dev_queue(priv->netdev, adapter);
if (netif_carrier_ok(priv->netdev))
netif_carrier_off(priv->netdev);
}
