Esempio n. 1
0
static int pm8058_kp_config_drv(int gpio_start, int num_gpios)
{
	int	rc;
	struct pm8058_gpio kypd_drv = {
		.direction	= PM_GPIO_DIR_OUT,
		.output_buffer	= PM_GPIO_OUT_BUF_OPEN_DRAIN,
		.output_value	= 0,
		.pull		= PM_GPIO_PULL_NO,
		.vin_sel	= 2,
		.out_strength	= PM_GPIO_STRENGTH_LOW,
		.function	= PM_GPIO_FUNC_1,
		.inv_int_pol	= 1,
	};

	if (gpio_start < 0 || num_gpios < 0 || num_gpios > PM8058_GPIOS)
		return -EINVAL;

	while (num_gpios--) {
		rc = pm8058_gpio_config(gpio_start++, &kypd_drv);
		if (rc) {
			pr_err("%s: FAIL pm8058_gpio_config(): rc=%d.\n",
				__func__, rc);
			return rc;
		}
	}

	return 0;
}

static int pm8058_kp_config_sns(int gpio_start, int num_gpios)
{
	int	rc;
	struct pm8058_gpio kypd_sns = {
		.direction	= PM_GPIO_DIR_IN,
		.pull		= PM_GPIO_PULL_UP_31P5,
		.vin_sel	= 2,
		.out_strength	= PM_GPIO_STRENGTH_NO,
		.function	= PM_GPIO_FUNC_NORMAL,
		.inv_int_pol	= 1,
	};

	if (gpio_start < 0 || num_gpios < 0 || num_gpios > PM8058_GPIOS)
		return -EINVAL;

	while (num_gpios--) {
		rc = pm8058_gpio_config(gpio_start++, &kypd_sns);
		if (rc) {
			pr_err("%s: FAIL pm8058_gpio_config(): rc=%d.\n",
				__func__, rc);
			return rc;
		}
	}

	return 0;
}

/*
 * keypad controller should be initialized in the following sequence
 * only, otherwise it might get into FSM stuck state.
 *
 * - Initialize keypad control parameters, like no. of rows, columns,
 *   timing values etc.,
 * - configure rows and column gpios pull up/down.
 * - set irq edge type.
 * - enable the keypad controller.
 */
static int __devinit pmic8058_kp_probe(struct platform_device *pdev)
{
	struct pmic8058_keypad_data *pdata = pdev->dev.platform_data;
	const struct matrix_keymap_data *keymap_data;
	struct pmic8058_kp *kp;
	int rc;
	unsigned short *keycodes;
	u8 ctrl_val;
	struct pm8058_chip	*pm_chip;

	pm_chip = platform_get_drvdata(pdev);
	if (pm_chip == NULL) {
		dev_err(&pdev->dev, "no parent data passed in\n");
		return -EFAULT;
	}

	if (!pdata || !pdata->num_cols || !pdata->num_rows ||
		pdata->num_cols > PM8058_MAX_COLS ||
		pdata->num_rows > PM8058_MAX_ROWS ||
		pdata->num_cols < PM8058_MIN_COLS
#if 0
 	||	pdata->num_rows < PM8058_MIN_ROWS
#endif
	) {
		dev_err(&pdev->dev, "invalid platform data\n");
		return -EINVAL;
	}

	if (pdata->rows_gpio_start < 0 || pdata->cols_gpio_start < 0) {
		dev_err(&pdev->dev, "invalid gpio_start platform data\n");
		return -EINVAL;
	}

	if (!pdata->scan_delay_ms || pdata->scan_delay_ms > MAX_SCAN_DELAY
		|| pdata->scan_delay_ms < MIN_SCAN_DELAY ||
		!is_power_of_2(pdata->scan_delay_ms)) {
		dev_err(&pdev->dev, "invalid keypad scan time supplied\n");
		return -EINVAL;
	}

	if (!pdata->row_hold_ns || pdata->row_hold_ns > MAX_ROW_HOLD_DELAY
		|| pdata->row_hold_ns < MIN_ROW_HOLD_DELAY ||
		((pdata->row_hold_ns % MIN_ROW_HOLD_DELAY) != 0)) {
		dev_err(&pdev->dev, "invalid keypad row hold time supplied\n");
		return -EINVAL;
	}

	if (pm8058_rev(pm_chip) == PM_8058_REV_1p0) {
		if (!pdata->debounce_ms
			|| !is_power_of_2(pdata->debounce_ms[0])
			|| pdata->debounce_ms[0] > MAX_DEBOUNCE_A0_TIME
			|| pdata->debounce_ms[0] < MIN_DEBOUNCE_A0_TIME) {
			dev_err(&pdev->dev, "invalid debounce time supplied\n");
			return -EINVAL;
		}
	} else {
		if (!pdata->debounce_ms
			|| ((pdata->debounce_ms[1] % 5) != 0)
			|| pdata->debounce_ms[1] > MAX_DEBOUNCE_B0_TIME
			|| pdata->debounce_ms[1] < MIN_DEBOUNCE_B0_TIME) {
			dev_err(&pdev->dev, "invalid debounce time supplied\n");
			return -EINVAL;
		}
	}

	keymap_data = pdata->keymap_data;
	if (!keymap_data) {
		dev_err(&pdev->dev, "no keymap data supplied\n");
		return -EINVAL;
	}

	kp = kzalloc(sizeof(*kp), GFP_KERNEL);
	if (!kp)
		return -ENOMEM;

	keycodes = kzalloc(PM8058_MATRIX_MAX_SIZE * sizeof(*keycodes),
				 GFP_KERNEL);
	if (!keycodes) {
		rc = -ENOMEM;
		goto err_alloc_mem;
	}

	platform_set_drvdata(pdev, kp);
	mutex_init(&kp->mutex);

	kp->pdata	= pdata;
	kp->dev		= &pdev->dev;
	kp->keycodes	= keycodes;
	kp->pm_chip	= pm_chip;

	if (pm8058_rev(pm_chip) == PM_8058_REV_1p0)
		kp->flags |= KEYF_FIX_LAST_ROW;

	kp->input = input_allocate_device();
	if (!kp->input) {
		dev_err(&pdev->dev, "unable to allocate input device\n");
		rc = -ENOMEM;
		goto err_alloc_device;
	}

	/* Enable runtime PM ops, start in ACTIVE mode */
	rc = pm_runtime_set_active(&pdev->dev);
	if (rc < 0)
		dev_dbg(&pdev->dev, "unable to set runtime pm state\n");
	pm_runtime_enable(&pdev->dev);

	kp->key_sense_irq = platform_get_irq(pdev, 0);
	if (kp->key_sense_irq < 0) {
		dev_err(&pdev->dev, "unable to get keypad sense irq\n");
		rc = -ENXIO;
		goto err_get_irq;
	}

	kp->key_stuck_irq = platform_get_irq(pdev, 1);
	if (kp->key_stuck_irq < 0) {
		dev_err(&pdev->dev, "unable to get keypad stuck irq\n");
		rc = -ENXIO;
		goto err_get_irq;
	}

	if (pdata->input_name)
		kp->input->name = pdata->input_name;
	else
		kp->input->name = "PMIC8058 keypad";

	if (pdata->input_phys_device)
		kp->input->phys = pdata->input_phys_device;
	else
		kp->input->phys = "pmic8058_keypad/input0";

	kp->input->dev.parent	= &pdev->dev;

	kp->input->id.bustype	= BUS_HOST;
	kp->input->id.version	= 0x0001;
	kp->input->id.product	= 0x0001;
	kp->input->id.vendor	= 0x0001;

	kp->input->evbit[0]	= BIT_MASK(EV_KEY);

	if (pdata->rep)
		__set_bit(EV_REP, kp->input->evbit);

	kp->input->keycode	= keycodes;
	kp->input->keycodemax	= PM8058_MATRIX_MAX_SIZE;
	kp->input->keycodesize	= sizeof(*keycodes);

	matrix_keypad_build_keymap(keymap_data, PM8058_ROW_SHIFT,
					kp->input->keycode, kp->input->keybit);

	input_set_capability(kp->input, EV_MSC, MSC_SCAN);
	input_set_drvdata(kp->input, kp);

	rc = input_register_device(kp->input);
	if (rc < 0) {
		dev_err(&pdev->dev, "unable to register keypad input device\n");
		goto err_get_irq;
	}

	/* initialize keypad state */
	memset(kp->keystate, 0xff, sizeof(kp->keystate));
	memset(kp->stuckstate, 0xff, sizeof(kp->stuckstate));

	rc = pmic8058_kpd_init(kp);
	if (rc < 0) {
		dev_err(&pdev->dev, "unable to initialize keypad controller\n");
		goto err_kpd_init;
	}

	rc = pm8058_kp_config_sns(pdata->cols_gpio_start,
			pdata->num_cols);
	if (rc < 0) {
		dev_err(&pdev->dev, "unable to configure keypad sense lines\n");
		goto err_gpio_config;
	}

	rc = pm8058_kp_config_drv(pdata->rows_gpio_start,
			pdata->num_rows);
	if (rc < 0) {
		dev_err(&pdev->dev, "unable to configure keypad drive lines\n");
		goto err_gpio_config;
	}

	rc = request_threaded_irq(kp->key_sense_irq, NULL, pmic8058_kp_irq,
				 IRQF_TRIGGER_RISING, "pmic-keypad", kp);
	if (rc < 0) {
		dev_err(&pdev->dev, "failed to request keypad sense irq\n");
		goto err_req_sense_irq;
	}

	rc = request_threaded_irq(kp->key_stuck_irq, NULL,
				 pmic8058_kp_stuck_irq, IRQF_TRIGGER_RISING,
				 "pmic-keypad-stuck", kp);
	if (rc < 0) {
		dev_err(&pdev->dev, "failed to request keypad stuck irq\n");
		goto err_req_stuck_irq;
	}

	rc = pmic8058_kp_read_u8(kp, &ctrl_val, KEYP_CTRL);
	ctrl_val |= KEYP_CTRL_KEYP_EN;
	rc = pmic8058_kp_write_u8(kp, ctrl_val, KEYP_CTRL);

	kp->ctrl_reg = ctrl_val;

	__dump_kp_regs(kp, "probe");

	rc = device_create_file(&pdev->dev, &dev_attr_key_pressed);
	if (rc < 0)
		goto err_create_file;

	rc = device_create_file(&pdev->dev, &dev_attr_disable_kp);
	if (rc < 0)
		goto err_create_file;

	device_init_wakeup(&pdev->dev, pdata->wakeup);

	return 0;

err_create_file:
	free_irq(kp->key_stuck_irq, kp);
err_req_stuck_irq:
	free_irq(kp->key_sense_irq, kp);
err_req_sense_irq:
err_gpio_config:
err_kpd_init:
	input_unregister_device(kp->input);
	kp->input = NULL;
err_get_irq:
	pm_runtime_set_suspended(&pdev->dev);
	pm_runtime_disable(&pdev->dev);
	input_free_device(kp->input);
err_alloc_device:
	kfree(keycodes);
err_alloc_mem:
	kfree(kp);
	return rc;
}

static int __devexit pmic8058_kp_remove(struct platform_device *pdev)
{
	struct pmic8058_kp *kp = platform_get_drvdata(pdev);

//	sysfs_remove_group(&pdev->dev.kobj, &pmic8058_keys_attr_group);
	pm_runtime_set_suspended(&pdev->dev);
	pm_runtime_disable(&pdev->dev);
	device_remove_file(&pdev->dev, &dev_attr_key_pressed);
	device_remove_file(&pdev->dev, &dev_attr_disable_kp);
	device_init_wakeup(&pdev->dev, 0);
	free_irq(kp->key_stuck_irq, kp);
	free_irq(kp->key_sense_irq, kp);
	input_unregister_device(kp->input);
	platform_set_drvdata(pdev, NULL);
	kfree(kp->input->keycode);
	kfree(kp);

	return 0;
}

#ifdef CONFIG_PM
static int pmic8058_kp_suspend(struct device *dev)
{
	struct pmic8058_kp *kp = dev_get_drvdata(dev);

	if (device_may_wakeup(dev) && !pmic8058_kp_disabled(kp)) {
		enable_irq_wake(kp->key_sense_irq);
	} else {
		mutex_lock(&kp->mutex);
		pmic8058_kp_disable(kp);
		mutex_unlock(&kp->mutex);
	}

	return 0;
}

static int pmic8058_kp_resume(struct device *dev)
{
	struct pmic8058_kp *kp = dev_get_drvdata(dev);

	if (device_may_wakeup(dev) && !pmic8058_kp_disabled(kp)) {
		disable_irq_wake(kp->key_sense_irq);
	} else {
		mutex_lock(&kp->mutex);
		pmic8058_kp_enable(kp);
		mutex_unlock(&kp->mutex);
	}

	return 0;
}

static struct dev_pm_ops pm8058_kp_pm_ops = {
	.suspend	= pmic8058_kp_suspend,
	.resume		= pmic8058_kp_resume,
};
#endif

static struct platform_driver pmic8058_kp_driver = {
	.probe		= pmic8058_kp_probe,
	.remove		= __devexit_p(pmic8058_kp_remove),
	.driver		= {
		.name = "pm8058-keypad",
		.owner = THIS_MODULE,
#ifdef CONFIG_PM
		.pm = &pm8058_kp_pm_ops,
#endif
	},
};

static int __init pmic8058_kp_init(void)
{
	return platform_driver_register(&pmic8058_kp_driver);
}
module_init(pmic8058_kp_init);

static void __exit pmic8058_kp_exit(void)
{
	platform_driver_unregister(&pmic8058_kp_driver);
}
Esempio n. 2
0
static int pm8058_kp_config_drv(int gpio_start, int num_gpios)
{
	int	rc;
	struct pm8058_gpio kypd_drv = {
		.direction	= PM_GPIO_DIR_OUT,
		.output_buffer	= PM_GPIO_OUT_BUF_OPEN_DRAIN,
		.output_value	= 0,
		.pull		= PM_GPIO_PULL_NO,
		.vin_sel	= 2,
		.out_strength	= PM_GPIO_STRENGTH_LOW,
		.function	= PM_GPIO_FUNC_1,
		.inv_int_pol	= 1,
	};

	if (gpio_start < 0 || num_gpios < 0 || num_gpios > PM8058_GPIOS)
		return -EINVAL;

	while (num_gpios--) {
		rc = pm8058_gpio_config(gpio_start++, &kypd_drv);
		if (rc) {
			pr_err("%s: FAIL pm8058_gpio_config(): rc=%d.\n",
				__func__, rc);
			return rc;
		}
	}

	return 0;
}

static int pm8058_kp_config_sns(int gpio_start, int num_gpios)
{
	int	rc;
	struct pm8058_gpio kypd_sns = {
		.direction	= PM_GPIO_DIR_IN,
		.pull		= PM_GPIO_PULL_UP_31P5,
		.vin_sel	= 2,
		.out_strength	= PM_GPIO_STRENGTH_NO,
		.function	= PM_GPIO_FUNC_NORMAL,
		.inv_int_pol	= 1,
	};

	if (gpio_start < 0 || num_gpios < 0 || num_gpios > PM8058_GPIOS)
		return -EINVAL;

	while (num_gpios--) {
		rc = pm8058_gpio_config(gpio_start++, &kypd_sns);
		if (rc) {
			pr_err("%s: FAIL pm8058_gpio_config(): rc=%d.\n",
				__func__, rc);
			return rc;
		}
	}

	return 0;
}


static int __devinit pmic8058_kp_probe(struct platform_device *pdev)
{
	struct pmic8058_keypad_data *pdata = pdev->dev.platform_data;
	struct pmic8058_kp *kp;
	int rc, i;
	unsigned short *keycodes;
	u8 ctrl_val;
	struct pm8058_chip	*pm_chip;

	pm_chip = platform_get_drvdata(pdev);
	if (pm_chip == NULL) {
		dev_err(&pdev->dev, "no parent data passed in\n");
		return -EFAULT;
	}

	if (!pdata || !pdata->num_cols || !pdata->num_rows ||
		pdata->num_cols > MATRIX_MAX_COLS ||
		pdata->num_rows > MATRIX_MAX_ROWS ||
		pdata->num_cols < MATRIX_MIN_COLS ||
		pdata->num_rows < MATRIX_MIN_ROWS ||
		!pdata->keymap) {
		dev_err(&pdev->dev, "invalid platform data\n");
		return -EINVAL;
	}

	if (pdata->rows_gpio_start < 0 || pdata->cols_gpio_start < 0) {
		dev_err(&pdev->dev, "invalid gpio_start platform data\n");
		return -EINVAL;
	}

	if (!pdata->scan_delay_ms || pdata->scan_delay_ms > MAX_SCAN_DELAY
		|| pdata->scan_delay_ms < MIN_SCAN_DELAY ||
		!is_power_of_2(pdata->scan_delay_ms)) {
		dev_err(&pdev->dev, "invalid keypad scan time supplied\n");
		return -EINVAL;
	}

	if (!pdata->row_hold_ns || pdata->row_hold_ns > MAX_ROW_HOLD_DELAY
		|| pdata->row_hold_ns < MIN_ROW_HOLD_DELAY ||
		((pdata->row_hold_ns % MIN_ROW_HOLD_DELAY) != 0)) {
		dev_err(&pdev->dev, "invalid keypad row hold time supplied\n");
		return -EINVAL;
	}

	if (pm8058_rev(pm_chip) == PM_8058_REV_1p0) {
		if (!pdata->debounce_ms
			|| !is_power_of_2(pdata->debounce_ms[0])
			|| pdata->debounce_ms[0] > MAX_DEBOUNCE_A0_TIME
			|| pdata->debounce_ms[0] < MIN_DEBOUNCE_A0_TIME) {
			dev_err(&pdev->dev, "invalid debounce time supplied\n");
			return -EINVAL;
		}
	} else {
		if (!pdata->debounce_ms
			|| ((pdata->debounce_ms[1] % 5) != 0)
			|| pdata->debounce_ms[1] > MAX_DEBOUNCE_B0_TIME
			|| pdata->debounce_ms[1] < MIN_DEBOUNCE_B0_TIME) {
			dev_err(&pdev->dev, "invalid debounce time supplied\n");
			return -EINVAL;
		}
	}

	kp = kzalloc(sizeof(*kp), GFP_KERNEL);
	if (!kp)
		return -ENOMEM;

	keycodes = kzalloc(MATRIX_MAX_SIZE * sizeof(keycodes), GFP_KERNEL);
	if (!keycodes) {
		rc = -ENOMEM;
		goto err_alloc_mem;
	}

	platform_set_drvdata(pdev, kp);

	kp->pdata	= pdata;
	kp->dev		= &pdev->dev;
	kp->keycodes	= keycodes;
	kp->pm_chip	= pm_chip;

	if (pm8058_rev(pm_chip) == PM_8058_REV_1p0)
		kp->flags |= KEYF_FIX_LAST_ROW;

	kp->input = input_allocate_device();
	if (!kp->input) {
		dev_err(&pdev->dev, "unable to allocate input device\n");
		rc = -ENOMEM;
		goto err_alloc_device;
	}

	kp->key_sense_irq = platform_get_irq(pdev, 0);
	if (kp->key_sense_irq < 0) {
		dev_err(&pdev->dev, "unable to get keypad sense irq\n");
		rc = -ENXIO;
		goto err_get_irq;
	}

	kp->key_stuck_irq = platform_get_irq(pdev, 1);
	if (kp->key_stuck_irq < 0) {
		dev_err(&pdev->dev, "unable to get keypad stuck irq\n");
		rc = -ENXIO;
		goto err_get_irq;
	}

	if (pdata->input_name)
		kp->input->name = pdata->input_name;
	else
		kp->input->name = "PMIC8058 keypad";

	if (pdata->input_phys_device)
		kp->input->phys = pdata->input_phys_device;
	else
		kp->input->phys = "pmic8058_keypad/input0";

	kp->input->dev.parent	= &pdev->dev;

	kp->input->id.bustype	= BUS_HOST;
	kp->input->id.version	= 0x0001;
	kp->input->id.product	= 0x0001;
	kp->input->id.vendor	= 0x0001;

	kp->input->evbit[0]	= BIT_MASK(EV_KEY);

	if (pdata->rep)
		__set_bit(EV_REP, kp->input->evbit);

	kp->input->keycode	= keycodes;
	kp->input->keycodemax	= MATRIX_MAX_SIZE;
	kp->input->keycodesize	= sizeof(*keycodes);

	
	for (i = 0; i < pdata->keymap_size; i++) {
		unsigned int row = KEY_ROW(pdata->keymap[i]);
		unsigned int col = KEY_COL(pdata->keymap[i]);
		unsigned short keycode = KEY_VAL(pdata->keymap[i]);

		keycodes[(row << 3) + col] = keycode;
		__set_bit(keycode, kp->input->keybit);
	}
	__clear_bit(KEY_RESERVED, kp->input->keybit);

	input_set_capability(kp->input, EV_MSC, MSC_SCAN);
	input_set_drvdata(kp->input, kp);

	rc = input_register_device(kp->input);
	if (rc < 0) {
		dev_err(&pdev->dev, "unable to register keypad input device\n");
		goto err_get_irq;
	}

	
	memset(kp->keystate, 0xff, sizeof(kp->keystate));
	memset(kp->stuckstate, 0xff, sizeof(kp->stuckstate));

	rc = pmic8058_kpd_init(kp);
	if (rc < 0) {
		dev_err(&pdev->dev, "unable to initialize keypad controller\n");
		goto err_kpd_init;
	}

	rc = pm8058_kp_config_sns(pdata->cols_gpio_start,
			pdata->num_cols);
	if (rc < 0) {
		dev_err(&pdev->dev, "unable to configure keypad sense lines\n");
		goto err_gpio_config;
	}

	rc = pm8058_kp_config_drv(pdata->rows_gpio_start,
			pdata->num_rows);
	if (rc < 0) {
		dev_err(&pdev->dev, "unable to configure keypad drive lines\n");
		goto err_gpio_config;
	}

	rc = request_irq(kp->key_sense_irq, pmic8058_kp_irq,
				 IRQF_TRIGGER_RISING, "pmic-keypad", kp);
	if (rc < 0) {
		dev_err(&pdev->dev, "failed to request keypad sense irq\n");
		goto err_req_sense_irq;
	}

	rc = request_irq(kp->key_stuck_irq, pmic8058_kp_stuck_irq,
				 IRQF_TRIGGER_RISING, "pmic-keypad-stuck", kp);
	if (rc < 0) {
		dev_err(&pdev->dev, "failed to request keypad stuck irq\n");
		goto err_req_stuck_irq;
	}

	rc = pmic8058_kp_read(kp, &ctrl_val, KEYP_CTRL, 1);
	ctrl_val |= KEYP_CTRL_KEYP_EN;
	rc = pmic8058_kp_write_u8(kp, ctrl_val, KEYP_CTRL);

	__dump_kp_regs(kp, "probe");

	device_init_wakeup(&pdev->dev, pdata->wakeup);

	return 0;

err_req_stuck_irq:
	free_irq(kp->key_sense_irq, NULL);
err_req_sense_irq:
err_gpio_config:
err_kpd_init:
	input_unregister_device(kp->input);
	kp->input = NULL;
err_get_irq:
	input_free_device(kp->input);
err_alloc_device:
	kfree(keycodes);
err_alloc_mem:
	kfree(kp);
	return rc;
}

static int __devexit pmic8058_kp_remove(struct platform_device *pdev)
{
	struct pmic8058_kp *kp = platform_get_drvdata(pdev);

	device_init_wakeup(&pdev->dev, 0);
	free_irq(kp->key_stuck_irq, NULL);
	free_irq(kp->key_sense_irq, NULL);
	input_unregister_device(kp->input);
	platform_set_drvdata(pdev, NULL);
	kfree(kp->input->keycode);
	kfree(kp);

	return 0;
}

static struct platform_driver pmic8058_kp_driver = {
	.probe		= pmic8058_kp_probe,
	.remove		= __devexit_p(pmic8058_kp_remove),
	.driver		= {
		.name = "pm8058-keypad",
		.owner = THIS_MODULE,
#ifdef CONFIG_PM
		.pm = &pm8058_kp_pm_ops,
#endif
	},
};

static int __init pmic8058_kp_init(void)
{
	return platform_driver_register(&pmic8058_kp_driver);
}
module_init(pmic8058_kp_init);

static void __exit pmic8058_kp_exit(void)
{
	platform_driver_unregister(&pmic8058_kp_driver);
}