int do_diag (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
{
unsigned int i;
if (argc == 1 || strcmp (argv[1], "run") != 0) {
/* List test info */
if (argc == 1) {
puts ("Available hardware tests:\n");
post_info (NULL);
puts ("Use 'diag [<test1> [<test2> ...]]'"
" to get more info.\n");
puts ("Use 'diag run [<test1> [<test2> ...]]'"
" to run tests.\n");
} else {
for (i = 1; i < argc; i++) {
if (post_info (argv[i]) != 0)
printf ("%s - no such test\n", argv[i]);
}
}
} else {
/* Run tests */
if (argc == 2) {
post_run (NULL, POST_RAM | POST_MANUAL);
} else {
for (i = 2; i < argc; i++) {
if (post_run (argv[i], POST_RAM | POST_MANUAL) != 0)
printf ("%s - unable to execute the test\n",
argv[i]);
}
}
}
return 0;
}
static int init_post(void)
{
post_bootmode_init();
post_run(NULL, POST_ROM | post_bootmode_get(0));
return 0;
}
void board_init_f(ulong bootflag)
{
bd_t *bd;
init_fnc_t **init_fnc_ptr;
gd_t *id;
ulong addr, addr_sp;
#ifdef CONFIG_PRAM
ulong reg;
#endif
void *new_fdt = NULL;
size_t fdt_size = 0;
memset((void *)gd, 0, sizeof(gd_t));
gd->mon_len = (ulong)&__bss_end - (ulong)_start;
#ifdef CONFIG_OF_EMBED
/* Get a pointer to the FDT */
gd->fdt_blob = __dtb_db_begin;
#elif defined CONFIG_OF_SEPARATE
/* FDT is at end of image */
gd->fdt_blob = &_end;
#endif
/* Allow the early environment to override the fdt address */
gd->fdt_blob = (void *)getenv_ulong("fdtcontroladdr", 16,
(uintptr_t)gd->fdt_blob);
for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) {
if ((*init_fnc_ptr)() != 0) {
hang ();
}
}
#ifdef CONFIG_OF_CONTROL
/* For now, put this check after the console is ready */
if (fdtdec_prepare_fdt()) {
panic("** CONFIG_OF_CONTROL defined but no FDT - please see "
"doc/README.fdt-control");
}
#endif
debug("monitor len: %08lX\n", gd->mon_len);
/*
* Ram is setup, size stored in gd !!
*/
debug("ramsize: %08lX\n", gd->ram_size);
#if defined(CONFIG_SYS_MEM_TOP_HIDE)
/*
* Subtract specified amount of memory to hide so that it won't
* get "touched" at all by U-Boot. By fixing up gd->ram_size
* the Linux kernel should now get passed the now "corrected"
* memory size and won't touch it either. This should work
* for arch/ppc and arch/powerpc. Only Linux board ports in
* arch/powerpc with bootwrapper support, that recalculate the
* memory size from the SDRAM controller setup will have to
* get fixed.
*/
gd->ram_size -= CONFIG_SYS_MEM_TOP_HIDE;
#endif
addr = CONFIG_SYS_SDRAM_BASE + get_effective_memsize();
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* reserve kernel log buffer */
addr -= (LOGBUFF_RESERVE);
debug("Reserving %dk for kernel logbuffer at %08lx\n", LOGBUFF_LEN,
addr);
#endif
#endif
#ifdef CONFIG_PRAM
/*
* reserve protected RAM
*/
reg = getenv_ulong("pram", 10, CONFIG_PRAM);
addr -= (reg << 10); /* size is in kB */
debug("Reserving %ldk for protected RAM at %08lx\n", reg, addr);
#endif /* CONFIG_PRAM */
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
/* reserve TLB table */
gd->arch.tlb_size = PGTABLE_SIZE;
addr -= gd->arch.tlb_size;
/* round down to next 64 kB limit */
addr &= ~(0x10000 - 1);
gd->arch.tlb_addr = addr;
debug("TLB table from %08lx to %08lx\n", addr, addr + gd->arch.tlb_size);
#endif
/* round down to next 4 kB limit */
addr &= ~(4096 - 1);
debug("Top of RAM usable for U-Boot at: %08lx\n", addr);
#ifdef CONFIG_LCD
#ifdef CONFIG_FB_ADDR
gd->fb_base = CONFIG_FB_ADDR;
#else
/* reserve memory for LCD display (always full pages) */
addr = lcd_setmem(addr);
gd->fb_base = addr;
#endif /* CONFIG_FB_ADDR */
#endif /* CONFIG_LCD */
/*
* reserve memory for U-Boot code, data & bss
* round down to next 4 kB limit
*/
addr -= gd->mon_len;
addr &= ~(4096 - 1);
debug("Reserving %ldk for U-Boot at: %08lx\n", gd->mon_len >> 10, addr);
#ifndef CONFIG_SPL_BUILD
/*
* reserve memory for malloc() arena
*/
addr_sp = addr - TOTAL_MALLOC_LEN;
debug("Reserving %dk for malloc() at: %08lx\n",
TOTAL_MALLOC_LEN >> 10, addr_sp);
/*
* (permanently) allocate a Board Info struct
* and a permanent copy of the "global" data
*/
addr_sp -= sizeof (bd_t);
bd = (bd_t *) addr_sp;
gd->bd = bd;
debug("Reserving %zu Bytes for Board Info at: %08lx\n",
sizeof (bd_t), addr_sp);
#ifdef CONFIG_MACH_TYPE
gd->bd->bi_arch_number = CONFIG_MACH_TYPE; /* board id for Linux */
#endif
addr_sp -= sizeof (gd_t);
id = (gd_t *) addr_sp;
debug("Reserving %zu Bytes for Global Data at: %08lx\n",
sizeof (gd_t), addr_sp);
#if defined(CONFIG_OF_SEPARATE) && defined(CONFIG_OF_CONTROL)
/*
* If the device tree is sitting immediate above our image then we
* must relocate it. If it is embedded in the data section, then it
* will be relocated with other data.
*/
if (gd->fdt_blob) {
fdt_size = ALIGN(fdt_totalsize(gd->fdt_blob) + 0x1000, 32);
addr_sp -= fdt_size;
new_fdt = (void *)addr_sp;
debug("Reserving %zu Bytes for FDT at: %08lx\n",
fdt_size, addr_sp);
}
#endif
#ifndef CONFIG_ARM64
/* setup stackpointer for exeptions */
gd->irq_sp = addr_sp;
#ifdef CONFIG_USE_IRQ
addr_sp -= (CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ);
debug("Reserving %zu Bytes for IRQ stack at: %08lx\n",
CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ, addr_sp);
#endif
/* leave 3 words for abort-stack */
addr_sp -= 12;
/* 8-byte alignment for ABI compliance */
addr_sp &= ~0x07;
#else /* CONFIG_ARM64 */
/* 16-byte alignment for ABI compliance */
addr_sp &= ~0x0f;
#endif /* CONFIG_ARM64 */
#else
addr_sp += 128; /* leave 32 words for abort-stack */
gd->irq_sp = addr_sp;
#endif
debug("New Stack Pointer is: %08lx\n", addr_sp);
#ifdef CONFIG_POST
post_bootmode_init();
post_run(NULL, POST_ROM | post_bootmode_get(0));
#endif
gd->bd->bi_baudrate = gd->baudrate;
/* Ram ist board specific, so move it to board code ... */
dram_init_banksize();
display_dram_config(); /* and display it */
gd->relocaddr = addr;
gd->start_addr_sp = addr_sp;
gd->reloc_off = addr - (ulong)&_start;
debug("relocation Offset is: %08lx\n", gd->reloc_off);
if (new_fdt) {
memcpy(new_fdt, gd->fdt_blob, fdt_size);
gd->fdt_blob = new_fdt;
}
memcpy(id, (void *)gd, sizeof(gd_t));
}
static int initr_post(void)
{
post_run(NULL, POST_RAM | post_bootmode_get(0));
return 0;
}
void board_init_r(gd_t *id, ulong dest_addr)
{
char *s;
bd_t *bd;
ulong malloc_start;
#if !defined(CONFIG_SYS_NO_FLASH)
ulong flash_size;
#endif
gd = id;
bd = gd->bd;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
monitor_flash_len = _end_ofs;
/*
* Enable D$:
* I$, if needed, must be already enabled in start.S
*/
dcache_enable();
debug("monitor flash len: %08lX\n", monitor_flash_len);
board_init(); /* Setup chipselects */
#ifdef CONFIG_SERIAL_MULTI
serial_initialize();
#endif
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is immediately below the monitor copy in DRAM */
malloc_start = dest_addr - TOTAL_MALLOC_LEN;
mem_malloc_init (malloc_start, TOTAL_MALLOC_LEN);
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
flash_size = flash_init();
if (flash_size > 0) {
# ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
s = getenv("flashchecksum");
if (s && (*s == 'y')) {
printf(" CRC: %08X", crc32(0,
(const unsigned char *) CONFIG_SYS_FLASH_BASE,
flash_size));
}
putc('\n');
# else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
# endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
#endif
#if defined(CONFIG_CMD_NAND)
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#if defined(CONFIG_CMD_ONENAND)
onenand_init();
#endif
#ifdef CONFIG_GENERIC_MMC
puts("MMC: ");
mmc_initialize(bd);
#endif
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
/* initialize environment */
env_relocate();
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
#endif
/* IP Address */
gd->bd->bi_ip_addr = getenv_IPaddr("ipaddr");
stdio_init(); /* get the devices list going. */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
console_init_r(); /* fully init console as a device */
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
/* Perform network card initialisation if necessary */
#if defined(CONFIG_DRIVER_SMC91111) || defined (CONFIG_DRIVER_LAN91C96)
/* XXX: this needs to be moved to board init */
if (getenv("ethaddr")) {
uchar enetaddr[6];
eth_getenv_enetaddr("ethaddr", enetaddr);
smc_set_mac_addr(enetaddr);
}
#endif /* CONFIG_DRIVER_SMC91111 || CONFIG_DRIVER_LAN91C96 */
/* Initialize from environment */
s = getenv("loadaddr");
if (s != NULL)
load_addr = simple_strtoul(s, NULL, 16);
#if defined(CONFIG_CMD_NET)
s = getenv("bootfile");
if (s != NULL)
copy_filename(BootFile, s, sizeof(BootFile));
#endif
#ifdef BOARD_LATE_INIT
board_late_init();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
#if defined(CONFIG_NET_MULTI)
puts("Net: ");
#endif
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram;
uchar memsz[32];
#ifdef CONFIG_PRAM
char *s;
s = getenv("pram");
if (s != NULL)
pram = simple_strtoul(s, NULL, 10);
else
pram = CONFIG_PRAM;
#else
pram = 0;
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf((char *)memsz, "%ldk", (bd->bi_memsize / 1024) - pram);
setenv("mem", (char *)memsz);
}
#endif
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
main_loop();
}
/* NOTREACHED - no way out of command loop except booting */
}
void board_init_f(ulong bootflag)
{
bd_t *bd;
init_fnc_t **init_fnc_ptr;
gd_t *id;
ulong addr, addr_sp;
/* Pointer is writable since we allocated a register for it */
gd = (gd_t *) ((CONFIG_SYS_INIT_SP_ADDR) & ~0x07);
/* compiler optimization barrier needed for GCC >= 3.4 */
__asm__ __volatile__("": : :"memory");
memset((void *)gd, 0, sizeof(gd_t));
gd->mon_len = _bss_end_ofs;
#ifdef CONFIG_MACH_TYPE
gd->bd->bi_arch_number = CONFIG_MACH_TYPE; /* board id for Linux */
#endif
for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) {
if ((*init_fnc_ptr)() != 0) {
hang ();
}
}
debug("monitor len: %08lX\n", gd->mon_len);
/*
* Ram is setup, size stored in gd !!
*/
debug("ramsize: %08lX\n", gd->ram_size);
#if defined(CONFIG_SYS_MEM_TOP_HIDE)
/*
* Subtract specified amount of memory to hide so that it won't
* get "touched" at all by U-Boot. By fixing up gd->ram_size
* the Linux kernel should now get passed the now "corrected"
* memory size and won't touch it either. This should work
* for arch/ppc and arch/powerpc. Only Linux board ports in
* arch/powerpc with bootwrapper support, that recalculate the
* memory size from the SDRAM controller setup will have to
* get fixed.
*/
gd->ram_size -= CONFIG_SYS_MEM_TOP_HIDE;
#endif
addr = CONFIG_SYS_SDRAM_BASE + gd->ram_size;
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* reserve kernel log buffer */
addr -= (LOGBUFF_RESERVE);
debug("Reserving %dk for kernel logbuffer at %08lx\n", LOGBUFF_LEN,
addr);
#endif
#endif
#ifdef CONFIG_PRAM
/*
* reserve protected RAM
*/
i = getenv_r("pram", (char *)tmp, sizeof(tmp));
reg = (i > 0) ? simple_strtoul((const char *)tmp, NULL, 10) :
CONFIG_PRAM;
addr -= (reg << 10); /* size is in kB */
debug("Reserving %ldk for protected RAM at %08lx\n", reg, addr);
#endif /* CONFIG_PRAM */
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
/* reserve TLB table */
addr -= (4096 * 4);
/* round down to next 64 kB limit */
addr &= ~(0x10000 - 1);
gd->tlb_addr = addr;
debug("TLB table at: %08lx\n", addr);
#endif
/* round down to next 4 kB limit */
addr &= ~(4096 - 1);
debug("Top of RAM usable for U-Boot at: %08lx\n", addr);
#ifdef CONFIG_LCD
#ifdef CONFIG_FB_ADDR
gd->fb_base = CONFIG_FB_ADDR;
#else
/* reserve memory for LCD display (always full pages) */
addr = lcd_setmem(addr);
gd->fb_base = addr;
#endif /* CONFIG_FB_ADDR */
#endif /* CONFIG_LCD */
/*
* reserve memory for U-Boot code, data & bss
* round down to next 4 kB limit
*/
addr -= gd->mon_len;
addr &= ~(4096 - 1);
debug("Reserving %ldk for U-Boot at: %08lx\n", gd->mon_len >> 10, addr);
#ifndef CONFIG_SPL_BUILD
/*
* reserve memory for malloc() arena
*/
addr_sp = addr - TOTAL_MALLOC_LEN;
debug("Reserving %dk for malloc() at: %08lx\n",
TOTAL_MALLOC_LEN >> 10, addr_sp);
/*
* (permanently) allocate a Board Info struct
* and a permanent copy of the "global" data
*/
addr_sp -= sizeof (bd_t);
bd = (bd_t *) addr_sp;
gd->bd = bd;
debug("Reserving %zu Bytes for Board Info at: %08lx\n",
sizeof (bd_t), addr_sp);
addr_sp -= sizeof (gd_t);
id = (gd_t *) addr_sp;
debug("Reserving %zu Bytes for Global Data at: %08lx\n",
sizeof (gd_t), addr_sp);
/* setup stackpointer for exeptions */
gd->irq_sp = addr_sp;
#ifdef CONFIG_USE_IRQ
addr_sp -= (CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ);
debug("Reserving %zu Bytes for IRQ stack at: %08lx\n",
CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ, addr_sp);
#endif
/* leave 3 words for abort-stack */
addr_sp -= 12;
/* 8-byte alignment for ABI compliance */
addr_sp &= ~0x07;
#else
addr_sp += 128; /* leave 32 words for abort-stack */
gd->irq_sp = addr_sp;
#endif
debug("New Stack Pointer is: %08lx\n", addr_sp);
#ifdef CONFIG_POST
post_bootmode_init();
post_run(NULL, POST_ROM | post_bootmode_get(0));
#endif
gd->bd->bi_baudrate = gd->baudrate;
/* Ram ist board specific, so move it to board code ... */
dram_init_banksize();
display_dram_config(); /* and display it */
gd->relocaddr = addr;
gd->start_addr_sp = addr_sp;
gd->reloc_off = addr - _TEXT_BASE;
debug("relocation Offset is: %08lx\n", gd->reloc_off);
memcpy(id, (void *)gd, sizeof(gd_t));
relocate_code(addr_sp, id, addr);
/* NOTREACHED - relocate_code() does not return */
}
/*
* This is the next part if the initialization sequence: we are now
* running from RAM and have a "normal" C environment, i. e. global
* data can be written, BSS has been cleared, the stack size in not
* that critical any more, etc.
*/
void board_init_r(gd_t *id, ulong dest_addr)
{
bd_t *bd;
ulong malloc_start;
#ifndef CONFIG_SYS_NO_FLASH
ulong flash_size;
#endif
gd = id; /* initialize RAM version of global data */
bd = gd->bd;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
/* The Malloc area is immediately below the monitor copy in DRAM */
malloc_start = dest_addr - TOTAL_MALLOC_LEN;
#if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx)
/*
* The gd->arch.cpu pointer is set to an address in flash before
* relocation. We need to update it to point to the same CPU entry
* in RAM.
*/
gd->arch.cpu += dest_addr - CONFIG_SYS_MONITOR_BASE;
/*
* If we didn't know the cpu mask & # cores, we can save them of
* now rather than 'computing' them constantly
*/
fixup_cpu();
#endif
#ifdef CONFIG_SYS_EXTRA_ENV_RELOC
/*
* Some systems need to relocate the env_addr pointer early because the
* location it points to will get invalidated before env_relocate is
* called. One example is on systems that might use a L2 or L3 cache
* in SRAM mode and initialize that cache from SRAM mode back to being
* a cache in cpu_init_r.
*/
gd->env_addr += dest_addr - CONFIG_SYS_MONITOR_BASE;
#endif
serial_initialize();
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
WATCHDOG_RESET();
/*
* Setup trap handlers
*/
trap_init(dest_addr);
#ifdef CONFIG_ADDR_MAP
init_addr_map();
#endif
#if defined(CONFIG_BOARD_EARLY_INIT_R)
board_early_init_r();
#endif
monitor_flash_len = (ulong)&__init_end - dest_addr;
WATCHDOG_RESET();
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
WATCHDOG_RESET();
#if defined(CONFIG_SYS_DELAYED_ICACHE)
icache_enable(); /* it's time to enable the instruction cache */
#endif
#if defined(CONFIG_SYS_INIT_RAM_LOCK) && defined(CONFIG_E500)
unlock_ram_in_cache(); /* it's time to unlock D-cache in e500 */
#endif
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_EARLY_PCI_INIT)
/*
* Do early PCI configuration _before_ the flash gets initialised,
* because PCU ressources are crucial for flash access on some boards.
*/
pci_init();
#endif
#if defined(CONFIG_WINBOND_83C553)
/*
* Initialise the ISA bridge
*/
initialise_w83c553f();
#endif
asm("sync ; isync");
mem_malloc_init(malloc_start, TOTAL_MALLOC_LEN);
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
if (board_flash_wp_on()) {
printf("Uninitialized - Write Protect On\n");
/* Since WP is on, we can't find real size. Set to 0 */
flash_size = 0;
} else if ((flash_size = flash_init()) > 0) {
#ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
if (getenv_yesno("flashchecksum") == 1) {
printf(" CRC: %08X",
crc32(0,
(const unsigned char *)
CONFIG_SYS_FLASH_BASE, flash_size)
);
}
putc('\n');
#else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
#endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
/* update start of FLASH memory */
bd->bi_flashstart = CONFIG_SYS_FLASH_BASE;
/* size of FLASH memory (final value) */
bd->bi_flashsize = flash_size;
#if defined(CONFIG_SYS_UPDATE_FLASH_SIZE)
/* Make a update of the Memctrl. */
update_flash_size(flash_size);
#endif
#if defined(CONFIG_OXC) || defined(CONFIG_RMU)
/* flash mapped at end of memory map */
bd->bi_flashoffset = CONFIG_SYS_TEXT_BASE + flash_size;
#elif CONFIG_SYS_MONITOR_BASE == CONFIG_SYS_FLASH_BASE
bd->bi_flashoffset = monitor_flash_len; /* reserved area for monitor */
#endif
#endif /* !CONFIG_SYS_NO_FLASH */
WATCHDOG_RESET();
/* initialize higher level parts of CPU like time base and timers */
cpu_init_r();
WATCHDOG_RESET();
#ifdef CONFIG_SPI
#if !defined(CONFIG_ENV_IS_IN_EEPROM)
spi_init_f();
#endif
spi_init_r();
#endif
#if defined(CONFIG_CMD_NAND)
WATCHDOG_RESET();
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#ifdef CONFIG_GENERIC_MMC
/*
* MMC initialization is called before relocating env.
* Thus It is required that operations like pin multiplexer
* be put in board_init.
*/
WATCHDOG_RESET();
puts("MMC: ");
mmc_initialize(bd);
#endif
/* relocate environment function pointers etc. */
env_relocate();
/*
* after non-volatile devices & environment is setup and cpu code have
* another round to deal with any initialization that might require
* full access to the environment or loading of some image (firmware)
* from a non-volatile device
*/
cpu_secondary_init_r();
/*
* Fill in missing fields of bd_info.
* We do this here, where we have "normal" access to the
* environment; we used to do this still running from ROM,
* where had to use getenv_f(), which can be pretty slow when
* the environment is in EEPROM.
*/
#if defined(CONFIG_SYS_EXTBDINFO)
#if defined(CONFIG_405GP) || defined(CONFIG_405EP)
#if defined(CONFIG_I2CFAST)
/*
* set bi_iic_fast for linux taking environment variable
* "i2cfast" into account
*/
{
if (getenv_yesno("i2cfast") == 1) {
bd->bi_iic_fast[0] = 1;
bd->bi_iic_fast[1] = 1;
}
}
#endif /* CONFIG_I2CFAST */
#endif /* CONFIG_405GP, CONFIG_405EP */
#endif /* CONFIG_SYS_EXTBDINFO */
#if defined(CONFIG_SC3)
sc3_read_eeprom();
#endif
#if defined(CONFIG_ID_EEPROM) || defined(CONFIG_SYS_I2C_MAC_OFFSET)
mac_read_from_eeprom();
#endif
#ifdef CONFIG_CMD_NET
/* kept around for legacy kernels only ... ignore the next section */
eth_getenv_enetaddr("ethaddr", bd->bi_enetaddr);
#ifdef CONFIG_HAS_ETH1
eth_getenv_enetaddr("eth1addr", bd->bi_enet1addr);
#endif
#ifdef CONFIG_HAS_ETH2
eth_getenv_enetaddr("eth2addr", bd->bi_enet2addr);
#endif
#ifdef CONFIG_HAS_ETH3
eth_getenv_enetaddr("eth3addr", bd->bi_enet3addr);
#endif
#ifdef CONFIG_HAS_ETH4
eth_getenv_enetaddr("eth4addr", bd->bi_enet4addr);
#endif
#ifdef CONFIG_HAS_ETH5
eth_getenv_enetaddr("eth5addr", bd->bi_enet5addr);
#endif
#endif /* CONFIG_CMD_NET */
WATCHDOG_RESET();
#if defined(CONFIG_PCI) && !defined(CONFIG_SYS_EARLY_PCI_INIT)
/*
* Do pci configuration
*/
pci_init();
#endif
/** leave this here (after malloc(), environment and PCI are working) **/
/* Initialize stdio devices */
stdio_init();
/* Initialize the jump table for applications */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
/* Initialize the console (after the relocation and devices init) */
console_init_r();
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
#if defined(CONFIG_CMD_KGDB)
WATCHDOG_RESET();
puts("KGDB: ");
kgdb_init();
#endif
debug("U-Boot relocated to %08lx\n", dest_addr);
/*
* Enable Interrupts
*/
interrupt_init();
#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
status_led_set(STATUS_LED_BOOT, STATUS_LED_BLINKING);
#endif
udelay(20);
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
WATCHDOG_RESET();
#if defined(CONFIG_CMD_SCSI)
WATCHDOG_RESET();
puts("SCSI: ");
scsi_init();
#endif
#if defined(CONFIG_CMD_DOC)
WATCHDOG_RESET();
puts("DOC: ");
doc_init();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
WATCHDOG_RESET();
puts("Net: ");
eth_initialize(bd);
#endif
#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
WATCHDOG_RESET();
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_CMD_PCMCIA) \
&& !defined(CONFIG_CMD_IDE)
WATCHDOG_RESET();
puts("PCMCIA:");
pcmcia_init();
#endif
#if defined(CONFIG_CMD_IDE)
WATCHDOG_RESET();
#ifdef CONFIG_IDE_8xx_PCCARD
puts("PCMCIA:");
#else
puts("IDE: ");
#endif
#if defined(CONFIG_START_IDE)
if (board_start_ide())
ide_init();
#else
ide_init();
#endif
#endif
#ifdef CONFIG_LAST_STAGE_INIT
WATCHDOG_RESET();
/*
* Some parts can be only initialized if all others (like
* Interrupts) are up and running (i.e. the PC-style ISA
* keyboard).
*/
last_stage_init();
#endif
#if defined(CONFIG_CMD_BEDBUG)
WATCHDOG_RESET();
bedbug_init();
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram = 0;
char memsz[32];
#ifdef CONFIG_PRAM
pram = getenv_ulong("pram", 10, CONFIG_PRAM);
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf(memsz, "%ldk", (ulong) (bd->bi_memsize / 1024) - pram);
setenv("mem", memsz);
}
#endif
#ifdef CONFIG_PS2KBD
puts("PS/2: ");
kbd_init();
#endif
/* Initialization complete - start the monitor */
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
WATCHDOG_RESET();
main_loop();
}
/* NOTREACHED - no way out of command loop except booting */
}
/*
************************************************************************
*
* This is the next part if the initialization sequence: we are now
* running from RAM and have a "normal" C environment, i. e. global
* data can be written, BSS has been cleared, the stack size in not
* that critical any more, etc.
*
************************************************************************
*/
void board_init_r(gd_t *id, ulong dest_addr)
{
char *s;
//bd_t *bd;
ulong malloc_start;
#ifdef CONFIG_NONCACHE_MEMORY
uint malloc_noncache_start;
#endif
#if !defined(CONFIG_SYS_NO_FLASH)
ulong flash_size;
#endif
int workmode;
int ret;
#ifdef CONFIG_SUNXI_HDCP_IN_SECURESTORAGE
int hdcpkey_enable=0;
#endif
char storage_type_buf[24] = {0};
char boot_mmc_buf[24] = {0};
gd = id;
//bd = gd->bd;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
monitor_flash_len = _end_ofs;
malloc_start = dest_addr - TOTAL_MALLOC_LEN - sizeof(struct spare_boot_head_t);
#ifdef CONFIG_NONCACHE_MEMORY_SIZE
malloc_start &= (~(0x00100000 -1));
malloc_noncache_start = malloc_start - CONFIG_NONCACHE_MEMORY_SIZE;
gd->malloc_noncache_start = malloc_noncache_start;
#endif
/* Enable caches */
enable_caches();
debug("monitor flash len: %08lX\n", monitor_flash_len);
board_init(); /* Setup chipselects */
#ifdef CONFIG_SERIAL_MULTI
serial_initialize();
#endif
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is immediately below the monitor copy in DRAM */
mem_malloc_init (malloc_start, TOTAL_MALLOC_LEN);
#ifdef CONFIG_SMALL_MEMSIZE
save_config();
#endif
#ifdef CONFIG_NONCACHE_MEMORY
mem_noncache_malloc_init(malloc_noncache_start, CONFIG_NONCACHE_MEMORY_SIZE);
#endif
#if defined(CONFIG_ARCH_HOMELET)
check_physical_key_early();
#endif
workmode = uboot_spare_head.boot_data.work_mode;
debug("work mode %d\n", workmode);
axp_reinit();
//uboot_spare_head.boot_data.work_mode = WORK_MODE_CARD_PRODUCT;
#if defined(CONFIG_CPUS_STANDBY) //Ŀǰֻ��homelet��ʹ��
do_box_standby();
#endif
#ifdef CONFIG_ARCH_HOMELET
gpio_control();
#endif
#if 0
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
flash_size = flash_init();
if (flash_size > 0) {
# ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
s = getenv("flashchecksum");
if (s && (*s == 'y')) {
printf(" CRC: %08X", crc32(0,
(const unsigned char *) CONFIG_SYS_FLASH_BASE,
flash_size));
}
putc('\n');
# else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
# endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
#endif
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
sunxi_dma_init();
#ifdef CONFIG_USE_CIR //����ӿڣ�Ŀǰֻ���ں��� A20
if (uboot_spare_head.boot_data.work_mode == WORK_MODE_BOOT)
{
ir_setup();
}
#endif
#ifdef DEBUG
puts("ready to config storage\n");
#endif
#ifdef CONFIG_ARCH_HOMELET //for homlet to use one-key-recovery
ret = sunxi_flash_handle_init();
if(!ret)
{
sunxi_partition_init();
}
#endif
#ifndef CONFIG_ARCH_SUN8IW8P1
if((workmode == WORK_MODE_BOOT) || (workmode == WORK_MODE_CARD_PRODUCT) || (workmode == WORK_MODE_SPRITE_RECOVERY))
{
#else
if((workmode == WORK_MODE_CARD_PRODUCT) || (workmode == WORK_MODE_SPRITE_RECOVERY))
{
#endif
#if (defined(CONFIG_SUNXI_DISPLAY) || defined(CONFIG_SUN7I_DISPLAY))
drv_disp_init();
#endif
#ifdef CONFIG_SUNXI_HDCP_IN_SECURESTORAGE
int tmp = 0;
tmp = script_parser_fetch("hdmi_para", "hdmi_hdcp_enable", &hdcpkey_enable, 1);
if((tmp) || (hdcpkey_enable != 1))
{
board_display_device_open();
board_display_layer_request();
}
#else
board_display_device_open();
board_display_layer_request();
#endif
}
#ifndef CONFIG_ARCH_HOMELET //for pad used
ret = sunxi_flash_handle_init();
if(!ret)
{
sunxi_partition_init();
}
#endif
#ifdef CONFIG_SUNXI_HDCP_IN_SECURESTORAGE
//here: write key to hardware
if(hdcpkey_enable==1)
{
char buffer[4096];
int data_len;
int ret0;
memset(buffer, 0, 4096);
ret0 = sunxi_secure_storage_init();
if(ret0)
{
printf("sunxi init secure storage failed\n");
}
else
{
ret0 = sunxi_secure_object_read("hdcpkey", buffer, 4096, &data_len);
if(ret0)
{
printf("probe hdcp key failed\n");
}
else
{
ret0 = smc_aes_bssk_decrypt_to_keysram(buffer, data_len);
if(ret0)
{
printf("push hdcp key failed\n");
}
else
{
board_display_device_open();
board_display_layer_request();
}
}
}
}
#endif
#ifdef CONFIG_BOOT_A15
if(sunxi_sprite_download_boot0_simple())
{
printf("rewrite boot0 to save boot cpu failed\n");
}
#endif
#ifndef CONFIG_SUNXI_SPINOR_PLATFORM
sunxi_keydata_burn_by_usb();
#endif
//#else
//#if defined(CONFIG_CMD_NAND)
// if(!storage_type){
// puts("NAND: ");
// nand_init(); /* go init the NAND */
// }
//#endif/*CONFIG_CMD_NAND*/
//
//#if defined(CONFIG_GENERIC_MMC)
// if(storage_type){
// puts("MMC: ");
// mmc_initialize(bd);
// }
//#endif/*CONFIG_GENERIC_MMC*/
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
/* initialize environment */
env_relocate();
/* setenv storage_type */
sprintf(storage_type_buf, "%d", uboot_spare_head.boot_data.storage_type);
if (setenv("storage_type", storage_type_buf))
printf("set storage_type=%s fail\n", storage_type_buf);
if (uboot_spare_head.boot_data.storage_type == 1)
sprintf(boot_mmc_buf, "%s", "0");
else
sprintf(boot_mmc_buf, "%s", "2");
setenv("boot_mmc", boot_mmc_buf);
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
#endif
/* IP Address */
gd->bd->bi_ip_addr = getenv_IPaddr("ipaddr");
stdio_init(); /* get the devices list going. */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
console_init_r(); /* fully init console as a device */
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* Perform network card initialisation if necessary */
#if defined(CONFIG_DRIVER_SMC91111) || defined (CONFIG_DRIVER_LAN91C96)
/* XXX: this needs to be moved to board init */
if (getenv("ethaddr")) {
uchar enetaddr[6];
eth_getenv_enetaddr("ethaddr", enetaddr);
smc_set_mac_addr(enetaddr);
}
#endif /* CONFIG_DRIVER_SMC91111 || CONFIG_DRIVER_LAN91C96 */
/* Initialize from environment */
s = getenv("loadaddr");
if (s != NULL)
load_addr = simple_strtoul(s, NULL, 16);
#if defined(CONFIG_CMD_NET)
s = getenv("bootfile");
if (s != NULL)
copy_filename(BootFile, s, sizeof(BootFile));
#endif
#ifdef BOARD_LATE_INIT
board_late_init();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
#if defined(CONFIG_NET_MULTI)
puts("Net: ");
#endif
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram;
uchar memsz[32];
#ifdef CONFIG_PRAM
char *s;
s = getenv("pram");
if (s != NULL)
pram = simple_strtoul(s, NULL, 10);
else
pram = CONFIG_PRAM;
#else
pram = 0;
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf((char *)memsz, "%ldk", (gd->ram_size / 1024) - pram);
setenv("mem", (char *)memsz);
}
#endif
//sprite_cartoon_test();
if(workmode == WORK_MODE_BOOT)
{
#if defined(CONFIG_SUNXI_SCRIPT_REINIT)
{
FATFS script_mount;
int ret;
uint read_bytes = 0;
FILE script_fs;
uchar *buf = NULL;
f_mount_ex(0, &script_mount, 0);
ret = f_open (&script_fs, "0:script.bin", FA_OPEN_EXISTING | FA_READ | FA_WRITE );
if(ret)
{
printf("cant open script.bin, maybe it is not exist\n");
}
else
{
buf = (uchar *)malloc(100 * 1024);
memset(buf, 0, 100 * 1024);
if(!f_read(&script_fs, buf, 100 * 1024, &read_bytes))
{
printf("f_read read bytes = %d\n", read_bytes);
}
f_close(&script_fs);
puts("try to unlink file ");
printf("%d\n", f_unlink("0:script.bin"));
}
f_mount(0, NULL, NULL);
if(read_bytes > 0)
{
char *tmp_target_buffer = (char *)(CONFIG_SYS_TEXT_BASE - 0x01000000);
sunxi_flash_exit(1);
memcpy(tmp_target_buffer + uboot_spare_head.boot_head.uboot_length, buf, read_bytes);
sunxi_sprite_download_uboot(tmp_target_buffer, uboot_spare_head.boot_data.storage_type, 1);
reset_cpu(0);
}
if(buf)
{
free(buf);
}
}
#endif
printf("WORK_MODE_BOOT\n");
#if (defined(CONFIG_SUNXI_DISPLAY) || defined(CONFIG_SUN7I_DISPLAY))
if(!ret)
{
#ifndef CONFIG_ARCH_HOMELET
printf("board_status_probe\n");
board_status_probe(0);
#endif
if(!gd->chargemode)
{
if(sunxi_advert_disp_probe())
{
printf("sunxi_bmp_logo_display\n");
sunxi_bmp_display("bootlogo.bmp");
}
else
{
if(sunxi_advert_display("Reserve0", "advert.bmp"))
{
printf("sunxi_bmp_logo_display\n");
sunxi_bmp_display("bootlogo.bmp");
}
}
}
else
{
printf("sunxi_bmp_charger_display\n");
sunxi_bmp_display("bat\\battery_charge.bmp");
}
}
#endif
#ifdef CONFIG_READ_LOGO_FOR_KERNEL
sunxi_read_bootlogo("boot_logo");
#endif
}
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;)
{
main_loop();
}
hang();
/* NOTREACHED - no way out of command loop except booting */
}
void hang(void)
{
puts("### ERROR ### Please RESET the board ###\n");
for (;;);
}
void board_init_r(gd_t *id, ulong dest_addr)
{
if (id)
gd = id;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
#ifdef CONFIG_SERIAL_MULTI
serial_initialize();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is at the top of simulated DRAM */
mem_malloc_init((ulong)gd->ram_buf + gd->ram_size - TOTAL_MALLOC_LEN,
TOTAL_MALLOC_LEN);
/* initialize environment */
env_relocate();
/* IP Address */
gd->bd->bi_ip_addr = getenv_IPaddr("ipaddr");
stdio_init(); /* get the devices list going. */
jumptable_init();
console_init_r(); /* fully init console as a device */
#if defined(CONFIG_DISPLAY_BOARDINFO_LATE)
checkboard();
#endif
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
#ifdef CONFIG_BOARD_LATE_INIT
board_late_init();
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
sandbox_main_loop_init();
/*
* For now, run the main loop. Later we might let this be done
* in the main program.
*/
while (1)
main_loop();
/* NOTREACHED - no way out of command loop except booting */
}
int post_run_r(void)
{
post_run(NULL, POST_RAM | post_bootmode_get(0));
return 0;
}
void board_init_r(gd_t *id, ulong dest_addr)
{
ulong malloc_start;
#if !defined(CONFIG_SYS_NO_FLASH)
ulong flash_size;
#endif
gd = id;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_R, "board_init_r");
monitor_flash_len = _end_ofs;/*u-boot.lds中定义*/
/* Enable caches */
enable_caches();
debug("monitor flash len: %08lX\n", monitor_flash_len);
board_init(); /* Setup chipselects//打印一些版本信息，电源管理信息 */
/*
* TODO: printing of the clock inforamtion of the board is now
* implemented as part of bdinfo command. Currently only support for
* davinci SOC's is added. Remove this check once all the board
* implement this.
*/
#ifdef CONFIG_CLOCKS
set_cpu_clk_info(); /* Setup clock information */
#endif
#ifdef CONFIG_SERIAL_MULTI
#ifndef CONFIG_CPU_EXYNOS5410
serial_initialize();
#endif
#endif
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is immediately below the monitor copy in DRAM */
malloc_start = dest_addr - TOTAL_MALLOC_LEN;
mem_malloc_init (malloc_start, TOTAL_MALLOC_LEN);
#ifdef CONFIG_ARCH_EARLY_INIT_R
arch_early_init_r();
#endif
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
flash_size = flash_init();
if (flash_size > 0) {
# ifdef CONFIG_SYS_FLASH_CHECKSUM
char *s = getenv("flashchecksum");
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
if (s && (*s == 'y')) {
printf(" CRC: %08X", crc32(0,
(const unsigned char *) CONFIG_SYS_FLASH_BASE,
flash_size));
}
putc('\n');
# else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
# endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
#endif
#if defined(CONFIG_CMD_NAND)
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#if defined(CONFIG_CMD_ONENAND)
onenand_init();
#endif
#ifdef CONFIG_GENERIC_MMC
puts("MMC: ");
mmc_initialize(gd->bd);
#endif
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
/* initialize environment */
env_relocate();
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
#endif
stdio_init(); /* get the devices list going. */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
console_init_r(); /* fully init console as a device */
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
/* Perform network card initialisation if necessary */
#if defined(CONFIG_DRIVER_SMC91111) || defined (CONFIG_DRIVER_LAN91C96)
/* XXX: this needs to be moved to board init */
if (getenv("ethaddr")) {
uchar enetaddr[6];
eth_getenv_enetaddr("ethaddr", enetaddr);
smc_set_mac_addr(enetaddr);
}
#endif /* CONFIG_DRIVER_SMC91111 || CONFIG_DRIVER_LAN91C96 */
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
#ifdef CONFIG_BOARD_LATE_INIT
board_late_init();//晚点执行的初始化在smdk5420.c
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
puts("Net: ");
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram = 0;
uchar memsz[32];
#ifdef CONFIG_PRAM
pram = getenv_ulong("pram", 10, CONFIG_PRAM);
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf((char *)memsz, "%ldk", (gd->ram_size / 1024) - pram);
setenv("mem", (char *)memsz);
}
#endif
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
main_loop();//进入命令行模式
}
/* NOTREACHED - no way out of command loop except booting */
}
/*
划分系统内存使用
初始化设备,开发板,打印提示信息
*/
void board_init_f(ulong bootflag)
{
bd_t *bd;
init_fnc_t **init_fnc_ptr;
gd_t *id;
ulong addr, addr_sp;/*addr将指向用户正常访问的最高地址+1的位置；addr_sp指向堆起始位置 */
#ifdef CONFIG_PRAM
ulong reg;
#endif
bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_F, "board_init_f");
/* Pointer is writable since we allocated a register for it */
gd = (gd_t *) ((CONFIG_SYS_INIT_SP_ADDR) & ~0x07);
/* compiler optimization barrier needed for GCC >= 3.4 */
__asm__ __volatile__("": : :"memory");//告诉编译器内存已被修改
memset((void *)gd, 0, sizeof(gd_t));
gd->mon_len = _bss_end_ofs;// data & bss段大小总和
#ifdef CONFIG_OF_EMBED
/* Get a pointer to the FDT */
gd->fdt_blob = _binary_dt_dtb_start;
#elif defined CONFIG_OF_SEPARATE
/* FDT is at end of image */
gd->fdt_blob = (void *)(_end_ofs + _TEXT_BASE);
#endif
/* Allow the early environment to override the fdt address */
gd->fdt_blob = (void *)getenv_ulong("fdtcontroladdr", 16,
(uintptr_t)gd->fdt_blob);
//执行init_fnc_ptr函数指针数组中的各个初始化函数
for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) {
if ((*init_fnc_ptr)() != 0) { //如果板的初始化函数序列出错，死循环
hang ();
}
}
#ifdef CONFIG_OF_CONTROL
/* For now, put this check after the console is ready */
if (fdtdec_prepare_fdt()) {
panic("** CONFIG_OF_CONTROL defined but no FDT - please see "
"doc/README.fdt-control");
}
#endif
debug("monitor len: %08lX\n", gd->mon_len);
/*
* Ram is setup, size stored in gd !!
*/
debug("ramsize: %08lX\n", gd->ram_size);
#if defined(CONFIG_SYS_MEM_TOP_HIDE)
/*
* Subtract specified amount of memory to hide so that it won't
* get "touched" at all by U-Boot. By fixing up gd->ram_size
* the Linux kernel should now get passed the now "corrected"
* memory size and won't touch it either. This should work
* for arch/ppc and arch/powerpc. Only Linux board ports in
* arch/powerpc with bootwrapper support, that recalculate the
* memory size from the SDRAM controller setup will have to
* get fixed.
*/
gd->ram_size -= CONFIG_SYS_MEM_TOP_HIDE;
#endif
/*设置addr = SDRAM起始地址+SDRAM_SIZE*/
addr = CONFIG_SYS_SDRAM_BASE + gd->ram_size;
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* reserve kernel log buffer */
addr -= (LOGBUFF_RESERVE);
debug("Reserving %dk for kernel logbuffer at %08lx\n", LOGBUFF_LEN,
addr);
#endif
#endif
#ifdef CONFIG_PRAM
/*
* reserve protected RAM
*/
reg = getenv_ulong("pram", 10, CONFIG_PRAM);
addr -= (reg << 10); /* size is in kB */
debug("Reserving %ldk for protected RAM at %08lx\n", reg, addr);
#endif /* CONFIG_PRAM */
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
/* reserve TLB table */
addr -= (4096 * 4);
/* round down to next 64 kB limit */
addr &= ~(0x10000 - 1);
gd->tlb_addr = addr;
debug("TLB table at: %08lx\n", addr);
#endif
/* round down to next 4 kB limit */
addr &= ~(4096 - 1);
debug("Top of RAM usable for U-Boot at: %08lx\n", addr);
#ifdef CONFIG_LCD
#ifdef CONFIG_FB_ADDR
gd->fb_base = CONFIG_FB_ADDR;
#else
/* reserve memory for LCD display (always full pages) */
addr = lcd_setmem(addr);
gd->fb_base = addr;
#endif /* CONFIG_FB_ADDR */
#endif /* CONFIG_LCD */
/*
* reserve memory for U-Boot code, data & bss
* round down to next 4 kB limit
*/
addr -= gd->mon_len;
addr &= ~(4096 - 1);
debug("Reserving %ldk for U-Boot at: %08lx\n", gd->mon_len >> 10, addr);
#ifndef CONFIG_SPL_BUILD
/*
* reserve memory for malloc() arena
*/
addr_sp = addr - TOTAL_MALLOC_LEN;
debug("Reserving %dk for malloc() at: %08lx\n",
TOTAL_MALLOC_LEN >> 10, addr_sp);
/*
* (permanently) allocate a Board Info struct
* and a permanent copy of the "global" data
*/
addr_sp -= sizeof (bd_t);
bd = (bd_t *) addr_sp;
gd->bd = bd;
debug("Reserving %zu Bytes for Board Info at: %08lx\n",
sizeof (bd_t), addr_sp);
#ifdef CONFIG_MACH_TYPE
gd->bd->bi_arch_number = CONFIG_MACH_TYPE; /* board id for Linux */
#endif
addr_sp -= sizeof (gd_t);/*为gd在DRAM中保留存储空间*/
id = (gd_t *) addr_sp;
debug("Reserving %zu Bytes for Global Data at: %08lx\n",
sizeof (gd_t), addr_sp);
/* setup stackpointer for exeptions */
gd->irq_sp = addr_sp;
#ifdef CONFIG_USE_IRQ
addr_sp -= (CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ);
debug("Reserving %zu Bytes for IRQ stack at: %08lx\n",
CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ, addr_sp);
#endif
/* leave 3 words for abort-stack */
addr_sp -= 12;
/* 8-byte alignment for ABI compliance */
addr_sp &= ~0x07;
#else
addr_sp += 128; /* leave 32 words for abort-stack */
gd->irq_sp = addr_sp;
#endif
debug("New Stack Pointer is: %08lx\n", addr_sp);
#ifdef CONFIG_POST
post_bootmode_init();
post_run(NULL, POST_ROM | post_bootmode_get(0));
#endif
gd->bd->bi_baudrate = gd->baudrate;
/* Ram ist board specific, so move it to board code ... */
dram_init_banksize();
display_dram_config(); /* and display it */
gd->relocaddr = addr;
gd->start_addr_sp = addr_sp;
gd->reloc_off = addr - _TEXT_BASE;
debug("relocation Offset is: %08lx\n", gd->reloc_off);
memcpy(id, (void *)gd, sizeof(gd_t));
relocate_code(addr_sp, id, addr);
/* NOTREACHED - relocate_code() does not return */
}
void board_init_r(gd_t *id, ulong dest_addr)
{
char *s;
//bd_t *bd;
ulong malloc_start;
#ifdef CONFIG_NONCACHE_MEMORY
uint malloc_noncache_start;
#endif
#if !defined(CONFIG_SYS_NO_FLASH)
ulong flash_size;
#endif
int workmode;
int ret;
gd = id;
//bd = gd->bd;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
monitor_flash_len = _end_ofs;
malloc_start = dest_addr - TOTAL_MALLOC_LEN - sizeof(struct spare_boot_head_t);
#ifdef CONFIG_NONCACHE_MEMORY_SIZE
malloc_start &= (~(0x00100000 -1));
malloc_noncache_start = malloc_start - CONFIG_NONCACHE_MEMORY_SIZE;
gd->malloc_noncache_start = malloc_noncache_start;
#endif
/* Enable caches */
enable_caches();
debug("monitor flash len: %08lX\n", monitor_flash_len);
board_init(); /* Setup chipselects */
#ifdef CONFIG_SERIAL_MULTI
serial_initialize();
#endif
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is immediately below the monitor copy in DRAM */
mem_malloc_init (malloc_start, TOTAL_MALLOC_LEN);
#ifdef CONFIG_NONCACHE_MEMORY
mem_noncache_malloc_init(malloc_noncache_start, CONFIG_NONCACHE_MEMORY_SIZE);
#endif
workmode = uboot_spare_head.boot_data.work_mode;
debug("work mode %d\n", workmode);
axp_reinit();
//uboot_spare_head.boot_data.work_mode = WORK_MODE_CARD_PRODUCT;
#ifdef CONFIG_ARCH_HOMELET
gpio_control();
#endif
#if 0
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
flash_size = flash_init();
if (flash_size > 0) {
# ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
s = getenv("flashchecksum");
if (s && (*s == 'y')) {
printf(" CRC: %08X", crc32(0,
(const unsigned char *) CONFIG_SYS_FLASH_BASE,
flash_size));
}
putc('\n');
# else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
# endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
#endif
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
sunxi_dma_init();
#ifdef CONFIG_ALLWINNER
#ifdef DEBUG
puts("ready to config storage\n");
#endif
if((workmode == WORK_MODE_BOOT) || (workmode == WORK_MODE_CARD_PRODUCT))
{
#if defined(CONFIG_SUNXI_DISPLAY)
drv_disp_init();
#endif
board_display_device_open();
board_display_layer_request();
}
ret = sunxi_flash_handle_init();
if(!ret)
{
sunxi_partition_init();
}
#else
#if defined(CONFIG_CMD_NAND)
if(!storage_type){
puts("NAND: ");
nand_init(); /* go init the NAND */
}
#endif/*CONFIG_CMD_NAND*/
#if defined(CONFIG_GENERIC_MMC)
if(storage_type){
puts("MMC: ");
mmc_initialize(bd);
}
#endif/*CONFIG_GENERIC_MMC*/
#endif/*CONFIG_ALLWINNER*/
#ifdef CONFIG_ARCH_HOMELET
extern int check_boot_recovery_key();
extern int sprite_form_sysrecovery();
extern int sprite_led_init(void);
extern int sprite_led_exit(int status);
if (!check_boot_recovery_key())
{
sprite_led_init();
ret = sprite_form_sysrecovery();
sprite_led_exit(ret);
}
#endif
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
/* initialize environment */
env_relocate();
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
#endif
/* IP Address */
gd->bd->bi_ip_addr = getenv_IPaddr("ipaddr");
stdio_init(); /* get the devices list going. */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
console_init_r(); /* fully init console as a device */
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* Perform network card initialisation if necessary */
#if defined(CONFIG_DRIVER_SMC91111) || defined (CONFIG_DRIVER_LAN91C96)
/* XXX: this needs to be moved to board init */
if (getenv("ethaddr")) {
uchar enetaddr[6];
eth_getenv_enetaddr("ethaddr", enetaddr);
smc_set_mac_addr(enetaddr);
}
#endif /* CONFIG_DRIVER_SMC91111 || CONFIG_DRIVER_LAN91C96 */
/* Initialize from environment */
s = getenv("loadaddr");
if (s != NULL)
load_addr = simple_strtoul(s, NULL, 16);
#if defined(CONFIG_CMD_NET)
s = getenv("bootfile");
if (s != NULL)
copy_filename(BootFile, s, sizeof(BootFile));
#endif
#ifdef BOARD_LATE_INIT
board_late_init();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
#if defined(CONFIG_NET_MULTI)
puts("Net: ");
#endif
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram;
uchar memsz[32];
#ifdef CONFIG_PRAM
char *s;
s = getenv("pram");
if (s != NULL)
pram = simple_strtoul(s, NULL, 10);
else
pram = CONFIG_PRAM;
#else
pram = 0;
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf((char *)memsz, "%ldk", (gd->ram_size / 1024) - pram);
setenv("mem", (char *)memsz);
}
#endif
//sprite_cartoon_test();
if(workmode == WORK_MODE_BOOT)
{
#if defined(CONFIG_SUNXI_SCRIPT_REINIT)
{
FATFS script_mount;
int ret;
uint read_bytes = 0;
FIL script_fs;
uchar *buf = NULL;
f_mount(0, &script_mount);
ret = f_open (&script_fs, "0:script.bin", FA_OPEN_EXISTING | FA_READ | FA_WRITE );
if(ret)
{
printf("cant open script.bin, maybe it is not exist\n");
}
else
{
buf = (uchar *)malloc(100 * 1024);
memset(buf, 0, 100 * 1024);
if(!f_read(&script_fs, buf, 100 * 1024, &read_bytes))
{
printf("f_read read bytes = %d\n", read_bytes);
}
f_close(&script_fs);
puts("try to unlink file ");
printf("%d\n", f_unlink("0:script.bin"));
}
f_mount(0, NULL);
if(read_bytes > 0)
{
char *tmp_target_buffer = (char *)(CONFIG_SYS_TEXT_BASE - 0x01000000);
sunxi_flash_exit(1);
memcpy(tmp_target_buffer + uboot_spare_head.boot_head.uboot_length, buf, read_bytes);
sunxi_sprite_download_uboot(tmp_target_buffer, uboot_spare_head.boot_data.storage_type, 1);
reset_cpu(0);
}
if(buf)
{
free(buf);
}
}
#endif
printf("WORK_MODE_BOOT\n");
#ifdef CONFIG_ALLWINNER
#if (defined(CONFIG_SUN6I) || defined(CONFIG_A50) || defined(CONFIG_SUN7I))
if(!ret)
{
#ifndef CONFIG_ARCH_HOMELET
printf("board_status_probe\n");
board_status_probe(0);
#endif
printf("sunxi_bmp_display\n");
sunxi_bmp_display("bootlogo.bmp");
}
#endif
printf("WORK_MODE_BOOT\n");
#endif
}
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;)
{
main_loop();
}
hang();
/* NOTREACHED - no way out of command loop except booting */
}
void board_init_r(gd_t *id, ulong dest_addr)
{
char *s;
ulong size;
static bd_t bd_data;
static gd_t gd_data;
init_fnc_t **init_fnc_ptr;
show_boot_progress(0x21);
/* Global data pointer is now writable */
gd = &gd_data;
memcpy(gd, id, sizeof(gd_t));
/* compiler optimization barrier needed for GCC >= 3.4 */
__asm__ __volatile__("": : :"memory");
gd->bd = &bd_data;
memset (gd->bd, 0, sizeof (bd_t));
show_boot_progress(0x22);
gd->baudrate = CONFIG_BAUDRATE;
mem_malloc_init((((ulong)dest_addr - CONFIG_SYS_MALLOC_LEN)+3)&~3,
CONFIG_SYS_MALLOC_LEN);
for (init_fnc_ptr = init_sequence_r; *init_fnc_ptr; ++init_fnc_ptr) {
if ((*init_fnc_ptr)() != 0)
hang ();
}
show_boot_progress(0x23);
#ifdef CONFIG_SERIAL_MULTI
serial_initialize();
#endif
/* configure available FLASH banks */
size = flash_init();
display_flash_config(size);
show_boot_progress(0x24);
show_boot_progress(0x25);
/* initialize environment */
env_relocate ();
show_boot_progress(0x26);
#ifdef CONFIG_CMD_NET
/* IP Address */
bd_data.bi_ip_addr = getenv_IPaddr ("ipaddr");
#endif
#if defined(CONFIG_PCI)
/*
* Do pci configuration
*/
pci_init();
#endif
show_boot_progress(0x27);
stdio_init ();
jumptable_init ();
/* Initialize the console (after the relocation and devices init) */
console_init_r();
#ifdef CONFIG_MISC_INIT_R
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
#if defined(CONFIG_CMD_PCMCIA) && !defined(CONFIG_CMD_IDE)
WATCHDOG_RESET();
puts ("PCMCIA:");
pcmcia_init();
#endif
#if defined(CONFIG_CMD_KGDB)
WATCHDOG_RESET();
puts("KGDB: ");
kgdb_init();
#endif
/* enable exceptions */
enable_interrupts();
show_boot_progress(0x28);
#ifdef CONFIG_STATUS_LED
status_led_set (STATUS_LED_BOOT, STATUS_LED_BLINKING);
#endif
udelay(20);
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
#if defined(CONFIG_CMD_NET)
if ((s = getenv ("bootfile")) != NULL) {
copy_filename (BootFile, s, sizeof (BootFile));
}
#endif
WATCHDOG_RESET();
#if defined(CONFIG_CMD_IDE)
WATCHDOG_RESET();
puts("IDE: ");
ide_init();
#endif
#if defined(CONFIG_CMD_SCSI)
WATCHDOG_RESET();
puts("SCSI: ");
scsi_init();
#endif
#if defined(CONFIG_CMD_DOC)
WATCHDOG_RESET();
puts("DOC: ");
doc_init();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
WATCHDOG_RESET();
puts("Net: ");
eth_initialize(gd->bd);
#endif
#if ( defined(CONFIG_CMD_NET)) && (0)
WATCHDOG_RESET();
# ifdef DEBUG
puts ("Reset Ethernet PHY\n");
# endif
reset_phy();
#endif
#ifdef CONFIG_LAST_STAGE_INIT
WATCHDOG_RESET();
/*
* Some parts can be only initialized if all others (like
* Interrupts) are up and running (i.e. the PC-style ISA
* keyboard).
*/
last_stage_init();
#endif
#ifdef CONFIG_POST
post_run (NULL, POST_RAM | post_bootmode_get(0));
#endif
show_boot_progress(0x29);
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
main_loop();
}
/* NOTREACHED - no way out of command loop except booting */
}
void board_init_r(gd_t *id, ulong dest_addr)
{
ulong malloc_start;
#if !defined(CONFIG_SYS_NO_FLASH)
ulong flash_size;
#endif
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_R, "board_init_r");
monitor_flash_len = (ulong)&__rel_dyn_end - (ulong)_start;
/* Enable caches */
enable_caches();
debug("monitor flash len: %08lX\n", monitor_flash_len);
board_init(); /* Setup chipselects */
/*
* TODO: printing of the clock inforamtion of the board is now
* implemented as part of bdinfo command. Currently only support for
* davinci SOC's is added. Remove this check once all the board
* implement this.
*/
#ifdef CONFIG_CLOCKS
set_cpu_clk_info(); /* Setup clock information */
#endif
serial_initialize();
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is immediately below the monitor copy in DRAM */
malloc_start = dest_addr - TOTAL_MALLOC_LEN;
mem_malloc_init (malloc_start, TOTAL_MALLOC_LEN);
#ifdef CONFIG_ARCH_EARLY_INIT_R
arch_early_init_r();
#endif
power_init_board();
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
flash_size = flash_init();
if (flash_size > 0) {
# ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
if (getenv_yesno("flashchecksum") == 1) {
printf(" CRC: %08X", crc32(0,
(const unsigned char *) CONFIG_SYS_FLASH_BASE,
flash_size));
}
putc('\n');
# else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
# endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
#endif
#if defined(CONFIG_CMD_NAND)
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#if defined(CONFIG_CMD_ONENAND)
onenand_init();
#endif
#ifdef CONFIG_GENERIC_MMC
puts("MMC: ");
mmc_initialize(gd->bd);
#endif
#ifdef CONFIG_CMD_SCSI
puts("SCSI: ");
scsi_init();
#endif
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
/* initialize environment */
if (should_load_env())
env_relocate();
else
set_default_env(NULL);
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
#endif
stdio_init(); /* get the devices list going. */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
console_init_r(); /* fully init console as a device */
#ifdef CONFIG_DISPLAY_BOARDINFO_LATE
# ifdef CONFIG_OF_CONTROL
/* Put this here so it appears on the LCD, now it is ready */
display_fdt_model(gd->fdt_blob);
# else
checkboard();
# endif
#endif
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
#ifdef CONFIG_BOARD_LATE_INIT
board_late_init();
#endif
#ifdef CONFIG_FASTBOOT
fastboot_setup();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
puts("Net: ");
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram = 0;
uchar memsz[32];
#ifdef CONFIG_PRAM
pram = getenv_ulong("pram", 10, CONFIG_PRAM);
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf((char *)memsz, "%ldk", (gd->ram_size / 1024) - pram);
setenv("mem", (char *)memsz);
}
#endif
#ifdef CONFIG_FASTBOOT
check_fastboot();
#endif
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
main_loop();
}
/* NOTREACHED - no way out of command loop except booting */
}
void board_init_f(ulong bootflag)
{
cmd_tbl_t *cmdtp;
bd_t *bd;
unsigned char *s;
init_fnc_t **init_fnc_ptr;
int j;
int i;
char *e;
#ifndef CONFIG_SYS_NO_FLASH
ulong flash_size;
#endif
gd = (gd_t *) (CONFIG_SYS_GBL_DATA_OFFSET);
/* Clear initial global data */
memset((void *)gd, 0, sizeof(gd_t));
gd->bd = (bd_t *) (gd + 1); /* At end of global data */
gd->baudrate = CONFIG_BAUDRATE;
gd->cpu_clk = CONFIG_SYS_CLK_FREQ;
bd = gd->bd;
bd->bi_memstart = CONFIG_SYS_RAM_BASE;
bd->bi_memsize = CONFIG_SYS_RAM_SIZE;
bd->bi_flashstart = CONFIG_SYS_FLASH_BASE;
#if defined(CONFIG_SYS_SRAM_BASE) && defined(CONFIG_SYS_SRAM_SIZE)
bd->bi_sramstart = CONFIG_SYS_SRAM_BASE;
bd->bi_sramsize = CONFIG_SYS_SRAM_SIZE;
#endif
bd->bi_baudrate = CONFIG_BAUDRATE;
bd->bi_bootflags = bootflag; /* boot / reboot flag (for LynxOS) */
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
gd->reloc_off = CONFIG_SYS_RELOC_MONITOR_BASE - CONFIG_SYS_MONITOR_BASE;
for (init_fnc_ptr = init_sequence, j = 0; *init_fnc_ptr;
++init_fnc_ptr, j++) {
#ifdef DEBUG_INIT_SEQUENCE
if (j > 9)
str_init_seq[9] = '0' + (j / 10);
str_init_seq[10] = '0' + (j - (j / 10) * 10);
serial_puts(str_init_seq);
#endif
if ((*init_fnc_ptr + gd->reloc_off) () != 0) {
hang();
}
}
#ifdef DEBUG_INIT_SEQUENCE
serial_puts(str_init_seq_done);
#endif
/*
* Now that we have DRAM mapped and working, we can
* relocate the code and continue running from DRAM.
*
* Reserve memory at end of RAM for (top down in that order):
* - kernel log buffer
* - protected RAM
* - LCD framebuffer
* - monitor code
* - board info struct
*/
#ifdef DEBUG_MEM_LAYOUT
printf("CONFIG_SYS_MONITOR_BASE: 0x%lx\n", CONFIG_SYS_MONITOR_BASE);
printf("CONFIG_ENV_ADDR: 0x%lx\n", CONFIG_ENV_ADDR);
printf("CONFIG_SYS_RELOC_MONITOR_BASE: 0x%lx (%d)\n", CONFIG_SYS_RELOC_MONITOR_BASE,
CONFIG_SYS_MONITOR_LEN);
printf("CONFIG_SYS_MALLOC_BASE: 0x%lx (%d)\n", CONFIG_SYS_MALLOC_BASE,
CONFIG_SYS_MALLOC_LEN);
printf("CONFIG_SYS_INIT_SP_OFFSET: 0x%lx (%d)\n", CONFIG_SYS_INIT_SP_OFFSET,
CONFIG_SYS_STACK_SIZE);
printf("CONFIG_SYS_PROM_OFFSET: 0x%lx (%d)\n", CONFIG_SYS_PROM_OFFSET,
CONFIG_SYS_PROM_SIZE);
printf("CONFIG_SYS_GBL_DATA_OFFSET: 0x%lx (%d)\n", CONFIG_SYS_GBL_DATA_OFFSET,
CONFIG_SYS_GBL_DATA_SIZE);
#endif
#ifdef CONFIG_POST
post_bootmode_init();
post_run(NULL, POST_ROM | post_bootmode_get(0));
#endif
/*
* We have to relocate the command table manually
*/
for (cmdtp = &__u_boot_cmd_start; cmdtp != &__u_boot_cmd_end; cmdtp++) {
ulong addr;
addr = (ulong) (cmdtp->cmd) + gd->reloc_off;
#if DEBUG_COMMANDS
printf("Command \"%s\": 0x%08lx => 0x%08lx\n",
cmdtp->name, (ulong) (cmdtp->cmd), addr);
#endif
cmdtp->cmd =
(int (*)(struct cmd_tbl_s *, int, int, char *[]))addr;
addr = (ulong) (cmdtp->name) + gd->reloc_off;
cmdtp->name = (char *)addr;
if (cmdtp->usage) {
addr = (ulong) (cmdtp->usage) + gd->reloc_off;
cmdtp->usage = (char *)addr;
}
#ifdef CONFIG_SYS_LONGHELP
if (cmdtp->help) {
addr = (ulong) (cmdtp->help) + gd->reloc_off;
cmdtp->help = (char *)addr;
}
#endif
}
#if defined(CONFIG_CMD_AMBAPP) && defined(CONFIG_SYS_AMBAPP_PRINT_ON_STARTUP)
puts("AMBA:\n");
do_ambapp_print(NULL, 0, 0, NULL);
#endif
/* initialize higher level parts of CPU like time base and timers */
cpu_init_r();
/* start timer */
timer_interrupt_init();
/*
* Enable Interrupts before any calls to udelay,
* the flash driver may use udelay resulting in
* a hang if not timer0 IRQ is enabled.
*/
interrupt_init();
/* The Malloc area is immediately below the monitor copy in RAM */
mem_malloc_init(CONFIG_SYS_MALLOC_BASE,
CONFIG_SYS_MALLOC_END - CONFIG_SYS_MALLOC_BASE);
malloc_bin_reloc();
#if !defined(CONFIG_SYS_NO_FLASH)
puts("FLASH: ");
if ((flash_size = flash_init()) > 0) {
# ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
s = getenv("flashchecksum");
if (s && (*s == 'y')) {
printf(" CRC: %08lX",
crc32(0, (const unsigned char *)CONFIG_SYS_FLASH_BASE,
flash_size)
);
}
putc('\n');
# else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
# endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
bd->bi_flashstart = CONFIG_SYS_FLASH_BASE; /* update start of FLASH memory */
bd->bi_flashsize = flash_size; /* size of FLASH memory (final value) */
#if CONFIG_SYS_MONITOR_BASE == CONFIG_SYS_FLASH_BASE
bd->bi_flashoffset = monitor_flash_len; /* reserved area for startup monitor */
#else
bd->bi_flashoffset = 0;
#endif
#else /* CONFIG_SYS_NO_FLASH */
bd->bi_flashsize = 0;
bd->bi_flashstart = 0;
bd->bi_flashoffset = 0;
#endif /* !CONFIG_SYS_NO_FLASH */
#ifdef CONFIG_SPI
# if !defined(CONFIG_ENV_IS_IN_EEPROM)
spi_init_f();
# endif
spi_init_r();
#endif
/* relocate environment function pointers etc. */
env_relocate();
#if defined(CONFIG_BOARD_LATE_INIT)
board_late_init();
#endif
#ifdef CONFIG_ID_EEPROM
mac_read_from_eeprom();
#endif
/* IP Address */
bd->bi_ip_addr = getenv_IPaddr("ipaddr");
#if defined(CONFIG_PCI)
/*
* Do pci configuration
*/
pci_init();
#endif
/* Initialize stdio devices */
stdio_init();
/* Initialize the jump table for applications */
jumptable_init();
/* Initialize the console (after the relocation and devices init) */
console_init_r();
#ifdef CONFIG_SERIAL_SOFTWARE_FIFO
serial_buffered_init();
#endif
#ifdef CONFIG_STATUS_LED
status_led_set(STATUS_LED_BOOT, STATUS_LED_BLINKING);
#endif
udelay(20);
set_timer(0);
/* Initialize from environment */
if ((s = getenv("loadaddr")) != NULL) {
load_addr = simple_strtoul(s, NULL, 16);
}
#if defined(CONFIG_CMD_NET)
if ((s = getenv("bootfile")) != NULL) {
copy_filename(BootFile, s, sizeof(BootFile));
}
#endif /* CONFIG_CMD_NET */
WATCHDOG_RESET();
#if defined(CONFIG_CMD_DOC)
WATCHDOG_RESET();
puts("DOC: ");
doc_init();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
#if defined(CONFIG_NET_MULTI)
WATCHDOG_RESET();
puts("Net: ");
#endif
eth_initialize(bd);
#endif
#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
WATCHDOG_RESET();
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_CMD_IDE)
WATCHDOG_RESET();
puts("IDE: ");
ide_init();
#endif /* CONFIG_CMD_IDE */
#ifdef CONFIG_LAST_STAGE_INIT
WATCHDOG_RESET();
/*
* Some parts can be only initialized if all others (like
* Interrupts) are up and running (i.e. the PC-style ISA
* keyboard).
*/
last_stage_init();
#endif
#ifdef CONFIG_PS2KBD
puts("PS/2: ");
kbd_init();
#endif
prom_init();
/* main_loop */
for (;;) {
WATCHDOG_RESET();
main_loop();
}
}
void board_init_f(ulong bootflag)
{
bd_t *bd;
ulong len, addr, addr_sp;
ulong *s;
gd_t *id;
init_fnc_t **init_fnc_ptr;
#ifdef CONFIG_PRAM
ulong reg;
#endif
/* Pointer is writable since we allocated a register for it */
gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET);
/* compiler optimization barrier needed for GCC >= 3.4 */
__asm__ __volatile__("":::"memory");
#if !defined(CONFIG_CPM2) && !defined(CONFIG_MPC512X) && \
!defined(CONFIG_MPC83xx) && !defined(CONFIG_MPC85xx) && \
!defined(CONFIG_MPC86xx)
/* Clear initial global data */
memset((void *) gd, 0, sizeof(gd_t));
#endif
gd->flags = bootflag;
for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr)
if ((*init_fnc_ptr) () != 0)
hang();
#ifdef CONFIG_POST
post_bootmode_init();
post_run(NULL, POST_ROM | post_bootmode_get(NULL));
#endif
WATCHDOG_RESET();
/*
* Now that we have DRAM mapped and working, we can
* relocate the code and continue running from DRAM.
*
* Reserve memory at end of RAM for (top down in that order):
* - area that won't get touched by U-Boot and Linux (optional)
* - kernel log buffer
* - protected RAM
* - LCD framebuffer
* - monitor code
* - board info struct
*/
len = (ulong)&__bss_end - CONFIG_SYS_MONITOR_BASE;
/*
* Subtract specified amount of memory to hide so that it won't
* get "touched" at all by U-Boot. By fixing up gd->ram_size
* the Linux kernel should now get passed the now "corrected"
* memory size and won't touch it either. This should work
* for arch/ppc and arch/powerpc. Only Linux board ports in
* arch/powerpc with bootwrapper support, that recalculate the
* memory size from the SDRAM controller setup will have to
* get fixed.
*/
gd->ram_size -= CONFIG_SYS_MEM_TOP_HIDE;
addr = CONFIG_SYS_SDRAM_BASE + get_effective_memsize();
#if defined(CONFIG_MP) && (defined(CONFIG_MPC86xx) || defined(CONFIG_E500))
/*
* We need to make sure the location we intend to put secondary core
* boot code is reserved and not used by any part of u-boot
*/
if (addr > determine_mp_bootpg(NULL)) {
addr = determine_mp_bootpg(NULL);
debug("Reserving MP boot page to %08lx\n", addr);
}
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* reserve kernel log buffer */
addr -= (LOGBUFF_RESERVE);
debug("Reserving %dk for kernel logbuffer at %08lx\n", LOGBUFF_LEN,
addr);
#endif
#endif
#ifdef CONFIG_PRAM
/*
* reserve protected RAM
*/
reg = getenv_ulong("pram", 10, CONFIG_PRAM);
addr -= (reg << 10); /* size is in kB */
debug("Reserving %ldk for protected RAM at %08lx\n", reg, addr);
#endif /* CONFIG_PRAM */
/* round down to next 4 kB limit */
addr &= ~(4096 - 1);
debug("Top of RAM usable for U-Boot at: %08lx\n", addr);
#ifdef CONFIG_LCD
#ifdef CONFIG_FB_ADDR
gd->fb_base = CONFIG_FB_ADDR;
#else
/* reserve memory for LCD display (always full pages) */
addr = lcd_setmem(addr);
gd->fb_base = addr;
#endif /* CONFIG_FB_ADDR */
#endif /* CONFIG_LCD */
#if defined(CONFIG_VIDEO) && defined(CONFIG_8xx)
/* reserve memory for video display (always full pages) */
addr = video_setmem(addr);
gd->fb_base = addr;
#endif /* CONFIG_VIDEO */
/*
* reserve memory for U-Boot code, data & bss
* round down to next 4 kB limit
*/
addr -= len;
addr &= ~(4096 - 1);
#ifdef CONFIG_E500
/* round down to next 64 kB limit so that IVPR stays aligned */
addr &= ~(65536 - 1);
#endif
debug("Reserving %ldk for U-Boot at: %08lx\n", len >> 10, addr);
/*
* reserve memory for malloc() arena
*/
addr_sp = addr - TOTAL_MALLOC_LEN;
debug("Reserving %dk for malloc() at: %08lx\n",
TOTAL_MALLOC_LEN >> 10, addr_sp);
/*
* (permanently) allocate a Board Info struct
* and a permanent copy of the "global" data
*/
addr_sp -= sizeof(bd_t);
bd = (bd_t *) addr_sp;
memset(bd, 0, sizeof(bd_t));
gd->bd = bd;
debug("Reserving %zu Bytes for Board Info at: %08lx\n",
sizeof(bd_t), addr_sp);
addr_sp -= sizeof(gd_t);
id = (gd_t *) addr_sp;
debug("Reserving %zu Bytes for Global Data at: %08lx\n",
sizeof(gd_t), addr_sp);
/*
* Finally, we set up a new (bigger) stack.
*
* Leave some safety gap for SP, force alignment on 16 byte boundary
* Clear initial stack frame
*/
addr_sp -= 16;
addr_sp &= ~0xF;
s = (ulong *) addr_sp;
*s = 0; /* Terminate back chain */
*++s = 0; /* NULL return address */
debug("Stack Pointer at: %08lx\n", addr_sp);
/*
* Save local variables to board info struct
*/
bd->bi_memstart = CONFIG_SYS_SDRAM_BASE; /* start of memory */
bd->bi_memsize = gd->ram_size; /* size in bytes */
#ifdef CONFIG_SYS_SRAM_BASE
bd->bi_sramstart = CONFIG_SYS_SRAM_BASE; /* start of SRAM */
bd->bi_sramsize = CONFIG_SYS_SRAM_SIZE; /* size of SRAM */
#endif
#if defined(CONFIG_8xx) || defined(CONFIG_MPC8260) || defined(CONFIG_5xx) || \
defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
bd->bi_immr_base = CONFIG_SYS_IMMR; /* base of IMMR register */
#endif
#if defined(CONFIG_MPC5xxx)
bd->bi_mbar_base = CONFIG_SYS_MBAR; /* base of internal registers */
#endif
#if defined(CONFIG_MPC83xx)
bd->bi_immrbar = CONFIG_SYS_IMMR;
#endif
WATCHDOG_RESET();
bd->bi_intfreq = gd->cpu_clk; /* Internal Freq, in Hz */
bd->bi_busfreq = gd->bus_clk; /* Bus Freq, in Hz */
#if defined(CONFIG_CPM2)
bd->bi_cpmfreq = gd->arch.cpm_clk;
bd->bi_brgfreq = gd->arch.brg_clk;
bd->bi_sccfreq = gd->arch.scc_clk;
bd->bi_vco = gd->arch.vco_out;
#endif /* CONFIG_CPM2 */
#if defined(CONFIG_MPC512X)
bd->bi_ipsfreq = gd->arch.ips_clk;
#endif /* CONFIG_MPC512X */
#if defined(CONFIG_MPC5xxx)
bd->bi_ipbfreq = gd->arch.ipb_clk;
bd->bi_pcifreq = gd->pci_clk;
#endif /* CONFIG_MPC5xxx */
#ifdef CONFIG_SYS_EXTBDINFO
strncpy((char *) bd->bi_s_version, "1.2", sizeof(bd->bi_s_version));
strncpy((char *) bd->bi_r_version, U_BOOT_VERSION,
sizeof(bd->bi_r_version));
bd->bi_procfreq = gd->cpu_clk; /* Processor Speed, In Hz */
bd->bi_plb_busfreq = gd->bus_clk;
#if defined(CONFIG_405GP) || defined(CONFIG_405EP) || \
defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
bd->bi_pci_busfreq = get_PCI_freq();
bd->bi_opbfreq = get_OPB_freq();
#elif defined(CONFIG_XILINX_405)
bd->bi_pci_busfreq = get_PCI_freq();
#endif
#endif
debug("New Stack Pointer is: %08lx\n", addr_sp);
WATCHDOG_RESET();
gd->relocaddr = addr; /* Store relocation addr, useful for debug */
memcpy(id, (void *) gd, sizeof(gd_t));
relocate_code(addr_sp, id, addr);
/* NOTREACHED - relocate_code() does not return */
}
