/**
* @brief Low level HAL driver initialization.
*
* @notapi
*/
void hal_lld_init(void) {
/* Reset of all peripherals. AHB3 is not reseted because it could have
been initialized in the board initialization file (board.c).*/
rccResetAHB1(~0);
rccResetAHB2(~0);
rccResetAHB3(~0);
rccResetAPB1R1(~RCC_APB1RSTR1_PWRRST);
rccResetAPB1R2(~0);
rccResetAPB2(~0);
/* PWR clock enabled.*/
rccEnablePWRInterface(FALSE);
/* Initializes the backup domain.*/
hal_lld_backup_domain_init();
#if defined(STM32_DMA_REQUIRED)
dmaInit();
#endif
/* Programmable voltage detector enable.*/
#if STM32_PVD_ENABLE
PWR->CR1 |= PWR_CR1_PVDE | (STM32_PLS & STM32_PLS_MASK);
#endif /* STM32_PVD_ENABLE */
}
/**
* @brief Low level HAL driver initialization.
*
* @notapi
*/
void hal_lld_init(void) {
/* Reset of all peripherals. AHB3 is not reseted because it could have
been initialized in the board initialization file (board.c).
Note, GPIOs are not reset because initialized before this point in
board files.*/
rccResetAHB1(~STM32_GPIO_EN_MASK);
#if !defined(STM32F410xx)
rccResetAHB2(~0);
#endif
rccResetAPB1(~RCC_APB1RSTR_PWRRST);
rccResetAPB2(~0);
/* PWR clock enabled.*/
rccEnablePWRInterface(true);
/* Initializes the backup domain.*/
hal_lld_backup_domain_init();
/* DMA subsystems initialization.*/
#if defined(STM32_DMA_REQUIRED)
dmaInit();
#endif
/* IRQ subsystem initialization.*/
irqInit();
/* Programmable voltage detector enable.*/
#if STM32_PVD_ENABLE
PWR->CR |= PWR_CR_PVDE | (STM32_PLS & STM32_PLS_MASK);
#endif /* STM32_PVD_ENABLE */
}
/**
* @brief Low level HAL driver initialization.
*
* @notapi
*/
void hal_lld_init(void) {
/* Reset of all peripherals. AHB3 is not reseted because it could have
been initialized in the board initialization file (board.c).*/
rccResetAHB1(~0);
rccResetAHB2(~0);
rccResetAPB1(~RCC_APB1RSTR_PWRRST);
rccResetAPB2(~0);
/* SysTick initialization using the system clock.*/
SysTick->LOAD = STM32_HCLK / CH_FREQUENCY - 1;
SysTick->VAL = 0;
SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk |
SysTick_CTRL_ENABLE_Msk |
SysTick_CTRL_TICKINT_Msk;
/* DWT cycle counter enable.*/
SCS_DEMCR |= SCS_DEMCR_TRCENA;
DWT_CTRL |= DWT_CTRL_CYCCNTENA;
/* PWR clock enabled.*/
rccEnablePWRInterface(FALSE);
/* Initializes the backup domain.*/
hal_lld_backup_domain_init();
#if defined(STM32_DMA_REQUIRED)
dmaInit();
#endif
/* Programmable voltage detector enable.*/
#if STM32_PVD_ENABLE
PWR->CR |= PWR_CR_PVDE | (STM32_PLS & STM32_PLS_MASK);
#endif /* STM32_PVD_ENABLE */
}
