void initFlash(void) {
initLogging(&logger, "Flash memory");
print("initFlash()\r\n");
addConsoleAction("readconfig", readFromFlash);
addConsoleAction("writeconfig", writeToFlash);
addConsoleAction("resetconfig", doResetConfiguration);
readFromFlash();
}
/***********************************************************************
This is the main controller loop.
sequences of operations:
- reads from CAN bus or serial port 1.
- reads encoders (or ADC).
- computes the control value (a PID in this version).
- checks limits and other errors.
- sets PWM
- does extra functions (e.g. communicate with neighboring cards).
***********************************************************************/
void main(void)
{
Int32 PWMoutput [JN];
Int32 PWMoutput_old [JN];
byte i=0;
byte wi=0;
byte k=0;
UInt16 *value=0;
Int32 t1val=0;
Int32 PID_R= 2;
Int32 kpp=1;
Int16 current_turn=0;
Int16 print_number=0;
Int16 real_pos=0;
byte first_step=0;
#if (VERSION == 0x0351)
#define winSizeMax 32
#define initialWindowSize 4
#else
#define winSizeMax 32
#define initialWindowSize 30
#endif
byte divJntPos[JN]=INIT_ARRAY(initialWindowSize-1);
byte divJntVel[JN]=INIT_ARRAY(initialWindowSize-1);
byte divMotPos[JN]=INIT_ARRAY(initialWindowSize-1);
byte divMotVel[JN]=INIT_ARRAY(initialWindowSize-1);
byte headJntPos[JN]=INIT_ARRAY(0); //current joint pos
byte tailJntPos[JN]=INIT_ARRAY(0);
byte headJntVel[JN]=INIT_ARRAY(0); //current joint vel
byte tailJntVel[JN]=INIT_ARRAY(0);
byte headMotPos[JN]=INIT_ARRAY(0); //current motor pos
byte tailMotPos[JN]=INIT_ARRAY(0);
byte headMotVel[JN]=INIT_ARRAY(0); //current motor vel
byte tailMotVel[JN]=INIT_ARRAY(0);
Int32 jntPosWindow[winSizeMax][JN]; //max window size = winSizeMax
Int32 jntVelWindow[winSizeMax][JN]; //max window size = winSizeMax
Int32 motPosWindow[winSizeMax][JN]; //max window size = winSizeMax
Int32 motVelWindow[winSizeMax][JN]; //max window size = winSizeMax
Int16 _safeband[JN]; //it is a value for reducing the JOINT limit of 2*_safeband [tick encoder]
#ifdef TEMPERATURE_SENSOR
byte TempSensCount1 = 0;
UInt32 TempSensCount2 = 0;
byte temp_sens_status=0;
overtemp[0]=0;
overtemp[1]=0;
errortemp[0]=0;
errortemp[1]=0;
#endif
/* gets the address of flash memory from the linker */
_flash_addr = get_flash_addr();
/* enable interrupts */
setReg(SYS_CNTL, 0);
// IPL channels from 0 to 6 enabled
// external interrupts IRQA and IRQB disabled
setRegBits(IPR, 0xFE00);
// enable FAULT
__ENIGROUP (61, 3);
#if (VERSION == 0x0254)
#else
__ENIGROUP (60, 3);
#endif
// enable SCI
__ENIGROUP (52, 4);
__ENIGROUP (53, 4);
__ENIGROUP (50, 4);
__ENIGROUP (51, 4);
// enable data flash
__ENIGROUP (13, 4);
// enable CAN
__ENIGROUP (14, 6);
__ENIGROUP (15, 6);
__ENIGROUP (16, 6);
__ENIGROUP (17, 6);
// enable ADCA/ADCB
__ENIGROUP (55, 6);
__ENIGROUP (54, 6);
//enable PWM reload
__ENIGROUP (59, 7); // PMWA
#if (VERSION == 0x0254)
#else
__ENIGROUP (58, 7); // PWMB
#endif
// enable timers
// TIMER_A
__ENIGROUP (45, 7); //Timer for the encoder commutation if used
__ENIGROUP (44, 7); //
__ENIGROUP (43, 7); //
__ENIGROUP (42, 4); //TI1 1ms delay main loop
// TIMER_B
__ENIGROUP (41, 7); //
__ENIGROUP (40, 7); //
__ENIGROUP (39, 7); //
__ENIGROUP (38, 7);
// TIMER_C
__ENIGROUP (37, 1);
__ENIGROUP (36, 1);
__ENIGROUP (35, 1);
__ENIGROUP (34, 1);
// TIMER_D
__ENIGROUP (33, 7); //1ms delay duty cycle
__ENIGROUP (32, 1);
__ENIGROUP (31, 1);
__ENIGROUP (30, 1);
__EI();
flash_interface_init (JN);
readFromFlash (_flash_addr);
if (_version==_flash_version)
{
}
else
{
writeToFlash(_flash_addr);
}
__DI();
#warning "debug"// ;
__EI();
init_leds ();
#if (VERSION == 0x0254)
Init_Brushless_Comm (1,HALL);
#else
Init_Brushless_Comm (JN,HALL);
#endif
can_interface_init (JN);
init_strain ();
init_position_abs_ssi ();
#if VERSION ==0x0257
init_relative_position_abs_ssi();
#endif
init_faults (true,true,true);
init_position_encoder ();
TI1_init ();
//variable init
mainLoopOVF=0;
_count=0;
for(i=0;i<JN;i++)
{
_received_pid[i].rec_pid=0;
}
BUS_OFF=false;
#warning "debug"// ;
//__EI();
// print_version ();
/* initialization */
for (i=0; i<JN; i++) _calibrated[i] = false;
/* reset trajectory generation */
for (i=0; i<JN; i++) abort_trajectory (i, 0);
///////////////////////////////////////
// reset of the ABS_SSI
// this is needed because the AS5045 gives the first value wrong !!!
for (i=0; i<JN; i++) _position[i]=(Int32) Filter_Bit(get_position_abs_ssi(i));
for (i=0; i<JN; i++) _max_real_position[i]=Filter_Bit(4095);
//////////////////////////////////////
/* initialize speed and acceleration to zero (useful later on) */
for (i=0; i<JN; i++) _position_old[i] = 0;
for (i=0; i<JN; i++) _speed[i] = 0;
for (i=0; i<JN; i++) _accel[i] = 0;
for (i=0; i<JN; i++) _safeband[i] =5; //5 ticks => 1 grado di AEA.
for (i=0; i<JN; i++) PWMoutput [i] = PWMoutput_old[i] = 0;
/* reset the recursive windows for storage of position and velocity data */
/* (for velocity and position estimates) */
for(i=0;i<JN;i++)
{
for(wi=0;wi<winSizeMax;wi++)
{
jntPosWindow[wi][i]=_position[i];
jntVelWindow[wi][i]=0;
motPosWindow[wi][i]=0;
motVelWindow[wi][i]=0;
}
}
//set_relative_position_abs_ssi(1,get_absolute_real_position_abs_ssi(1));
/* main control loop */
for(_counter = 0;; _counter ++)
{
if (_counter >= CAN_SYNCHRO_STEPS) _counter = 0;
led3_on
while (_wait);
_count=0;
led3_off
// BUS_OFF check
if (getCanBusOffstatus() )
{
#ifdef DEBUG_CAN_MSG
can_printf("DISABLE BUS OFF");
#endif
for (i=0; i<JN; i++) put_motor_in_fault(i);
led1_off
}
else
led1_on
// READING CAN MESSAGES
can_interface();
for (i=0; i<JN; i++)
if (_pad_enabled[i]==false && _control_mode[i]!=MODE_HW_FAULT) _control_mode[i]=MODE_IDLE;
//Position calculation
// This is used to have a shift of the zero-cross out of the
// joint workspace
//
// max_real_position is the limit of the joint starting from
// 4095 and going to decrease this number without zero-cross
// untill the joint limit is reached
#if VERSION == 0x0257
_position_old[0]=_position[0];
if(get_error_abs_ssi(0)==ERR_OK)
_position[0]=Filter_Bit (get_position_abs_ssi(0));
_position_old[1]=_position[1];
if(get_error_abs_ssi(1)==ERR_OK)
_position[1]=Filter_Bit (get_position_abs_ssi(1));
#else
for (i=0; i<JN; i++)
{
_position_old[i]=_position[i];
if(get_error_abs_ssi(i)==ERR_OK)
_position[i]=Filter_Bit (get_position_abs_ssi(i));
}
#endif
// get_commutations() is used to read the incremental encoder of the motors.
// the variable _motor_position is then used to estimate the rotor speed and
// compensate the back-EMF of the motor.
for (i=0; i<JN; i++) _motor_position[i]=get_position_encoder(i);//get_commutations(i);
///////////////////////////////////////////DEBUG////////////
#if (VERSION !=0x0254)
for (i=0; i<JN; i++)
{
if (get_error_abs_ssi(i)==ERR_ABS_SSI)
{
put_motor_in_fault(i);
#ifdef DEBUG_CAN_MSG
can_printf("ABS error %d",i);
#endif
}
}
#endif
#if (VERSION ==0x0254)
if (get_error_abs_ssi(0)==ERR_ABS_SSI)
{
put_motor_in_fault(0);
#ifdef DEBUG_CAN_MSG
can_printf("ABS error %d",0);
#endif
}
#endif
//DO NOTHING
// decoupling the position
decouple_positions();
/* velocity and acceleration estimators */
{
for (i=0; i<JN; i++)
{
//joint velocity estimator
tailJntPos[i]=headJntPos[i]+(winSizeMax-divJntPos[i]); if(tailJntPos[i]>=winSizeMax) tailJntPos[i]=tailJntPos[i]%winSizeMax;
_speed_old[i] = _speed[i];
jntPosWindow[headJntPos[i]][i]=_position[i];
_speed[i] = (Int32) (((jntPosWindow[headJntPos[i]][i] - jntPosWindow[tailJntPos[i]][i] ))<<_jntVel_est_shift[i]);
// _speed[i] <<= _jntVel_est_shift[i];
_speed[i] = (Int32)(_speed[i]) / divJntPos[i];
headJntPos[i]=headJntPos[i]+1; if(headJntPos[i]>=winSizeMax) headJntPos[i]=0;
/*
//joint acceleration estimator
tailJntVel[i]=headJntVel[i]+(winSizeMax-divJntVel[i]); if(tailJntVel[i]>=winSizeMax) tailJntVel[i]=tailJntVel[i]%winSizeMax;
_accel_old[i] = _accel[i];
jntVelWindow[headJntVel[i]][i]=_speed[i];
_accel[i] = ((jntVelWindow[headJntVel[i]][i] - jntVelWindow[tailJntVel[i]][i] ));
_accel[i] << _jntAcc_est_shift[i];
_accel[i] = (Int32)(_accel[i]) / divJntVel[i];
headJntVel[i]=headJntVel[i]+1; if(headJntVel[i]>=winSizeMax) headJntVel[i]=0;
*/
//motor velocity estimator
tailMotPos[i]=headMotPos[i]+(winSizeMax-divMotPos[i]); if(tailMotPos[i]>=winSizeMax) tailMotPos[i]=tailMotPos[i]%winSizeMax;
_motor_speed_old[i] = _motor_speed[i];
motPosWindow[headMotPos[i]][i]=_motor_position[i];
_motor_speed[i] = ((motPosWindow[headMotPos[i]][i] - motPosWindow[tailMotPos[i]][i] ));
_motor_speed[i] <<= _motVel_est_shift[i];
_motor_speed[i] = (_motor_speed[i]) / divMotPos[i];
headMotPos[i]=headMotPos[i]+1; if(headMotPos[i]>=winSizeMax) headMotPos[i]=0;
}
}
/* in position? */
#if (VERSION != 0x0254)
for (i=0; i<JN; i++) _in_position[i] = check_in_position(i);
#else
_in_position[0] = check_in_position(0);
#endif
/* in reference configuration for calibration? */
//for (i=0; i<JN; i++) check_in_position_calib(i);
//******************************************* POSITION LIMIT CHECK ***************************/
for (i=0; i<JN; i++) check_range(i, _safeband[i], PWMoutput);
//******************************************* COMPUTES CONTROLS *****************************/
//FT sensor watchdog update
for (i=0; i<STRAIN_MAX; i++)
if (_strain_wtd[i]>0) _strain_wtd[i]--;
for (i=0; i<JN; i++)
{
//computing the PWM value (PID)
PWMoutput[i] = compute_pwm(i);
// PWM filtering in torque control if there is no bemf compensation
#if (VERSION != 0x0351)
if (_control_mode[i] == MODE_TORQUE ||
_control_mode[i] == MODE_IMPEDANCE_POS ||
_control_mode[i] == MODE_IMPEDANCE_VEL)
{
if (_useFilter[i] == 3) PWMoutput[i] = lpf_ord1_3hz (PWMoutput[i], i);
}
// saving the PWM value before the decoupling
_bfc_PWMoutput[i] = PWMoutput_old[i] = PWMoutput[i];
// applying the saturation to the PWM
if (_bfc_PWMoutput[i] < -MAX_DUTY) _bfc_PWMoutput[i]=-MAX_DUTY;
else if (_bfc_PWMoutput[i] > MAX_DUTY) _bfc_PWMoutput[i]= MAX_DUTY;
#endif //(VERSION != 0x0351)
}
//decouple PWM
decouple_dutycycle(PWMoutput);
//******************************************* SATURATES CONTROLS ***************************/
/* back emf compensation + controls saturation (if necessary) */
for (i=0; i<JN; i++)
{
if (_control_mode[i] == MODE_TORQUE ||
_control_mode[i] == MODE_IMPEDANCE_POS ||
_control_mode[i] == MODE_IMPEDANCE_VEL)
{
#if (VERSION != 0x0351)
// Back emf compensation
//PWMoutput[i]+=compensate_bemf(i, _comm_speed[i]); //use the motor speed
PWMoutput[i]+=compensate_bemf(i, _speed[i]); //use the joint speed
//add the coulomb friction compensation term
if (_kstp_torque[i] != 0 ||
_kstn_torque[i] != 0)
//PWMoutput[i]+=compensate_friction(i, _comm_speed[i]); //use the motor speed
PWMoutput[i]+=compensate_friction(i, _speed[i]); //use the joint speed
// Protection for joints out of the admissible range during force control
check_range_torque(i, _safeband[i], PWMoutput);
// PWM saturation
ENFORCE_LIMITS (i,PWMoutput[i], _pid_limit_torque[i] );
#else //(VERSION != 0x0351)
ENFORCE_LIMITS (i,PWMoutput[i], _pid_limit[i] );
#endif //(VERSION != 0x0351)
}
else
{
ENFORCE_LIMITS (i,PWMoutput[i], _pid_limit[i] );
}
if (_pid[i] < -MAX_DUTY) _pid[i]=-MAX_DUTY;
else if (_pid[i] > MAX_DUTY) _pid[i]= MAX_DUTY;
}
/* generate PWM */
for (i=0; i<JN; i++)
{
if (!mode_is_idle(i)) {PWM_generate(i,_pid[i]);}
}
/* Check Current done in T1 */
/* do extra functions, communicate, etc. */
//send broadcast data
can_send_broadcast();
//send additional debug information
//can_send_broadcast_debug(1,1);
/***********************************************************************
// Check Current is made here
/***********************************************************************/
#if (VERSION != 0x0254)
for (i=0; i<JN; i++)
#else
for (i=0; i<1; i++)
#endif
{
if ((get_current(i)>=25000) || (get_current(i)<=-25000))
{
put_motor_in_fault(i);
highcurrent[i]=true;
#ifdef DEBUG_CAN_MSG
can_printf("j%d curr %f",i,get_current(i));
#endif
}
check_current(i, (_pid[i] > 0));
compute_i2t(i);
if (_filt_current[i] > MAX_I2T_CURRENT)
{
put_motor_in_fault(i);
highcurrent[i]=true;
#ifdef DEBUG_CAN_MSG
can_printf("j%d filtcurr %f",i,_filt_current[i]);
#endif
}
}
// Check for the MAIN LOOP duration
// t1val= (UInt16) TI1_getCounter();
if ( _count>0)
{
mainLoopOVF=1;
_count=0;
}
/* tells that the control cycle is completed */
_wait = true;
} /* end for(;;) */
void initHardware(Logging *logger, Engine *engine) {
engine_configuration_s *engineConfiguration = engine->engineConfiguration;
efiAssertVoid(engineConfiguration!=NULL, "engineConfiguration");
board_configuration_s *boardConfiguration = &engineConfiguration->bc;
printMsg(logger, "initHardware()");
// todo: enable protection. it's disabled because it takes
// 10 extra seconds to re-flash the chip
//flashProtect();
chMtxInit(&spiMtx);
#if EFI_HISTOGRAMS
/**
* histograms is a data structure for CPU monitor, it does not depend on configuration
*/
initHistogramsModule();
#endif /* EFI_HISTOGRAMS */
/**
* This is so early because we want to init logger
* which would be used while finding trigger synch index
* while config read
*/
initTriggerDecoder();
/**
* We need the LED_ERROR pin even before we read configuration
*/
initPrimaryPins();
if (hasFirmwareError()) {
return;
}
initDataStructures(PASS_ENGINE_PARAMETER_F);
#if EFI_INTERNAL_FLASH
palSetPadMode(CONFIG_RESET_SWITCH_PORT, CONFIG_RESET_SWITCH_PIN, PAL_MODE_INPUT_PULLUP);
initFlash(engine);
/**
* this call reads configuration from flash memory or sets default configuration
* if flash state does not look right.
*/
if (SHOULD_INGORE_FLASH()) {
engineConfiguration->engineType = FORD_ASPIRE_1996;
resetConfigurationExt(logger, engineConfiguration->engineType, engine);
writeToFlash();
} else {
readFromFlash();
}
#else
engineConfiguration->engineType = FORD_ASPIRE_1996;
resetConfigurationExt(logger, engineConfiguration->engineType, engineConfiguration, engineConfiguration2, boardConfiguration);
#endif /* EFI_INTERNAL_FLASH */
if (hasFirmwareError()) {
return;
}
mySetPadMode2("board test", boardConfiguration->boardTestModeJumperPin, PAL_MODE_INPUT_PULLUP);
bool isBoardTestMode_b = GET_BOARD_TEST_MODE_VALUE();
initAdcInputs(isBoardTestMode_b);
if (isBoardTestMode_b) {
// this method never returns
initBoardTest();
}
initRtc();
initOutputPins();
#if EFI_HIP_9011
initHip9011();
#endif /* EFI_HIP_9011 */
#if EFI_MAX_31855
initMax31855(boardConfiguration);
#endif /* EFI_MAX_31855 */
#if EFI_CAN_SUPPORT
initCan();
#endif /* EFI_CAN_SUPPORT */
// init_adc_mcp3208(&adcState, &SPID2);
// requestAdcValue(&adcState, 0);
// todo: figure out better startup logic
initTriggerCentral(engine);
#if EFI_SHAFT_POSITION_INPUT
initShaftPositionInputCapture();
#endif /* EFI_SHAFT_POSITION_INPUT */
initSpiModules(boardConfiguration);
#if EFI_FILE_LOGGING
initMmcCard();
#endif /* EFI_FILE_LOGGING */
// initFixedLeds();
// initBooleanInputs();
#if EFI_UART_GPS
initGps();
#endif
#if ADC_SNIFFER
initAdcDriver();
#endif
#if EFI_HD44780_LCD
// initI2Cmodule();
lcd_HD44780_init();
if (hasFirmwareError())
return;
lcd_HD44780_print_string(VCS_VERSION);
#endif /* EFI_HD44780_LCD */
addConsoleActionII("i2c", sendI2Cbyte);
// while (true) {
// for (int addr = 0x20; addr < 0x28; addr++) {
// sendI2Cbyte(addr, 0);
// int err = i2cGetErrors(&I2CD1);
// print("I2C: err=%x from %d\r\n", err, addr);
// chThdSleepMilliseconds(5);
// sendI2Cbyte(addr, 255);
// chThdSleepMilliseconds(5);
// }
// }
printMsg(logger, "initHardware() OK!");
}
void initHardware(Logging *l) {
efiAssertVoid(CUSTOM_IH_STACK, getRemainingStack(chThdGetSelfX()) > 256, "init h");
sharedLogger = l;
engine_configuration_s *engineConfiguration = engine->engineConfigurationPtr;
efiAssertVoid(CUSTOM_EC_NULL, engineConfiguration!=NULL, "engineConfiguration");
board_configuration_s *boardConfiguration = &engineConfiguration->bc;
printMsg(sharedLogger, "initHardware()");
// todo: enable protection. it's disabled because it takes
// 10 extra seconds to re-flash the chip
//flashProtect();
chMtxObjectInit(&spiMtx);
#if EFI_HISTOGRAMS
/**
* histograms is a data structure for CPU monitor, it does not depend on configuration
*/
initHistogramsModule();
#endif /* EFI_HISTOGRAMS */
/**
* We need the LED_ERROR pin even before we read configuration
*/
initPrimaryPins();
if (hasFirmwareError()) {
return;
}
#if EFI_INTERNAL_FLASH
palSetPadMode(CONFIG_RESET_SWITCH_PORT, CONFIG_RESET_SWITCH_PIN, PAL_MODE_INPUT_PULLUP);
initFlash(sharedLogger);
/**
* this call reads configuration from flash memory or sets default configuration
* if flash state does not look right.
*/
if (SHOULD_INGORE_FLASH()) {
engineConfiguration->engineType = DEFAULT_ENGINE_TYPE;
resetConfigurationExt(sharedLogger, engineConfiguration->engineType PASS_ENGINE_PARAMETER_SUFFIX);
writeToFlashNow();
} else {
readFromFlash();
}
#else
engineConfiguration->engineType = DEFAULT_ENGINE_TYPE;
resetConfigurationExt(sharedLogger, engineConfiguration->engineType PASS_ENGINE_PARAMETER_SUFFIX);
#endif /* EFI_INTERNAL_FLASH */
#if EFI_HD44780_LCD
// initI2Cmodule();
lcd_HD44780_init(sharedLogger);
if (hasFirmwareError())
return;
lcd_HD44780_print_string(VCS_VERSION);
#endif /* EFI_HD44780_LCD */
if (hasFirmwareError()) {
return;
}
#if EFI_SHAFT_POSITION_INPUT || defined(__DOXYGEN__)
initTriggerDecoder();
#endif
bool isBoardTestMode_b;
if (CONFIGB(boardTestModeJumperPin) != GPIO_UNASSIGNED) {
efiSetPadMode("board test", CONFIGB(boardTestModeJumperPin),
PAL_MODE_INPUT_PULLUP);
isBoardTestMode_b = (!efiReadPin(CONFIGB(boardTestModeJumperPin)));
// we can now relese this pin, it is actually used as output sometimes
unmarkPin(CONFIGB(boardTestModeJumperPin));
} else {
isBoardTestMode_b = false;
}
#if HAL_USE_ADC || defined(__DOXYGEN__)
initAdcInputs(isBoardTestMode_b);
#endif
if (isBoardTestMode_b) {
// this method never returns
initBoardTest();
}
initRtc();
initOutputPins();
#if EFI_MAX_31855
initMax31855(sharedLogger, getSpiDevice(CONFIGB(max31855spiDevice)), CONFIGB(max31855_cs));
#endif /* EFI_MAX_31855 */
#if EFI_CAN_SUPPORT
initCan();
#endif /* EFI_CAN_SUPPORT */
// init_adc_mcp3208(&adcState, &SPID2);
// requestAdcValue(&adcState, 0);
#if EFI_SHAFT_POSITION_INPUT || defined(__DOXYGEN__)
// todo: figure out better startup logic
initTriggerCentral(sharedLogger);
#endif /* EFI_SHAFT_POSITION_INPUT */
turnOnHardware(sharedLogger);
#if HAL_USE_SPI || defined(__DOXYGEN__)
initSpiModules(boardConfiguration);
#endif
#if EFI_HIP_9011 || defined(__DOXYGEN__)
initHip9011(sharedLogger);
#endif /* EFI_HIP_9011 */
#if EFI_FILE_LOGGING || defined(__DOXYGEN__)
initMmcCard();
#endif /* EFI_FILE_LOGGING */
#if EFI_MEMS || defined(__DOXYGEN__)
initAccelerometer(PASS_ENGINE_PARAMETER_SIGNATURE);
#endif
// initFixedLeds();
#if EFI_BOSCH_YAW || defined(__DOXYGEN__)
initBoschYawRateSensor();
#endif /* EFI_BOSCH_YAW */
// initBooleanInputs();
#if EFI_UART_GPS || defined(__DOXYGEN__)
initGps();
#endif
#if EFI_SERVO
initServo();
#endif
#if ADC_SNIFFER || defined(__DOXYGEN__)
initAdcDriver();
#endif
#if HAL_USE_I2C || defined(__DOXYGEN__)
addConsoleActionII("i2c", sendI2Cbyte);
#endif
// USBMassStorageDriver UMSD1;
// while (true) {
// for (int addr = 0x20; addr < 0x28; addr++) {
// sendI2Cbyte(addr, 0);
// int err = i2cGetErrors(&I2CD1);
// print("I2C: err=%x from %d\r\n", err, addr);
// chThdSleepMilliseconds(5);
// sendI2Cbyte(addr, 255);
// chThdSleepMilliseconds(5);
// }
// }
#if EFI_VEHICLE_SPEED || defined(__DOXYGEN__)
initVehicleSpeed(sharedLogger);
#endif
#if EFI_CDM_INTEGRATION
cdmIonInit();
#endif
#if HAL_USE_EXT || defined(__DOXYGEN__)
initJoystick(sharedLogger);
#endif
calcFastAdcIndexes();
printMsg(sharedLogger, "initHardware() OK!");
}
