static void smm_relocate(void)
{
u32 smi_en;
printk(BIOS_DEBUG, "Initializing SMM handler...");
pmbase = pci_read_config16(dev_find_slot(0, PCI_DEVFN(0x1f, 0)), 0x40) & 0xfffc;
printk(BIOS_SPEW, " ... pmbase = 0x%04x\n", pmbase);
smi_en = inl(pmbase + SMI_EN);
if (smi_en & APMC_EN) {
printk(BIOS_INFO, "SMI# handler already enabled?\n");
return;
}
/* copy the SMM relocation code */
memcpy((void *)0x38000, &smm_relocation_start,
&smm_relocation_end - &smm_relocation_start);
printk(BIOS_DEBUG, "\n");
dump_smi_status(reset_smi_status());
dump_pm1_status(reset_pm1_status());
dump_gpe0_status(reset_gpe0_status());
dump_tco_status(reset_tco_status());
/* Enable SMI generation:
* - on TCO events
* - on APMC writes (io 0xb2)
* - on writes to SLP_EN (sleep states)
* - on writes to GBL_RLS (bios commands)
* No SMIs:
* - on microcontroller writes (io 0x62/0x66)
*/
outl(smi_en | (TCO_EN | APMC_EN | SLP_SMI_EN | BIOS_EN |
EOS | GBL_SMI_EN), pmbase + SMI_EN);
/**
* There are several methods of raising a controlled SMI# via
* software, among them:
* - Writes to io 0xb2 (APMC)
* - Writes to the Local Apic ICR with Delivery mode SMI.
*
* Using the local apic is a bit more tricky. According to
* AMD Family 11 Processor BKDG no destination shorthand must be
* used.
* The whole SMM initialization is quite a bit hardware specific, so
* I'm not too worried about the better of the methods at the moment
*/
/* raise an SMI interrupt */
printk(BIOS_SPEW, " ... raise SMI#\n");
outb(0x00, 0xb2);
}
static void southbridge_smi_tco(unsigned int node, smm_state_save_area_t *state_save)
{
u32 tco_sts;
tco_sts = reset_tco_status();
/* Any TCO event? */
if (!tco_sts)
return;
if (tco_sts & (1 << 8)) { // BIOSWR
u8 bios_cntl;
bios_cntl = pci_read_config16(PCI_DEV(0, 0x1f, 0), 0xdc);
if (bios_cntl & 1) {
/* BWE is RW, so the SMI was caused by a
* write to BWE, not by a write to the BIOS
*/
/* This is the place where we notice someone
* is trying to tinker with the BIOS. We are
* trying to be nice and just ignore it. A more
* resolute answer would be to power down the
* box.
*/
printk(BIOS_DEBUG, "Switching back to RO\n");
pci_write_config32(PCI_DEV(0, 0x1f, 0), 0xdc, (bios_cntl & ~1));
} /* No else for now? */
} else if (tco_sts & (1 << 3)) { /* TIMEOUT */
/* Handle TCO timeout */
printk(BIOS_DEBUG, "TCO Timeout.\n");
} else {
dump_tco_status(tco_sts);
}
}
static void smm_relocate(void)
{
u32 smi_en;
u16 pm1_en;
printk(BIOS_DEBUG, "Initializing SMM handler...");
pmbase = pci_read_config16(dev_find_slot(0, PCI_DEVFN(0x1f, 0)), D31F0_PMBASE) & 0xfffc;
printk(BIOS_SPEW, " ... pmbase = 0x%04x\n", pmbase);
smi_en = inl(pmbase + SMI_EN);
if (smi_en & GBL_SMI_EN) {
printk(BIOS_INFO, "SMI# handler already enabled?\n");
return;
}
/* copy the SMM relocation code */
memcpy((void *)0x38000, &smm_relocation_start,
&smm_relocation_end - &smm_relocation_start);
wbinvd();
printk(BIOS_DEBUG, "\n");
dump_smi_status(reset_smi_status());
dump_pm1_status(reset_pm1_status());
dump_gpe0_status(reset_gpe0_status());
dump_alt_gp_smi_status(reset_alt_gp_smi_status());
dump_tco_status(reset_tco_status());
/* Enable SMI generation:
* - on TCO events
* - on APMC writes (io 0xb2)
* - on writes to GBL_RLS (bios commands)
* No SMIs:
* - on microcontroller writes (io 0x62/0x66)
*/
smi_en = 0; /* reset SMI enables */
smi_en |= TCO_EN;
smi_en |= APMC_EN;
#if DEBUG_PERIODIC_SMIS
/* Set DEBUG_PERIODIC_SMIS in i82801ix.h to debug using
* periodic SMIs.
*/
smi_en |= PERIODIC_EN;
#endif
smi_en |= BIOS_EN;
/* The following need to be on for SMIs to happen */
smi_en |= EOS | GBL_SMI_EN;
outl(smi_en, pmbase + SMI_EN);
pm1_en = 0;
pm1_en |= PWRBTN_EN;
pm1_en |= GBL_EN;
outw(pm1_en, pmbase + PM1_EN);
/**
* There are several methods of raising a controlled SMI# via
* software, among them:
* - Writes to io 0xb2 (APMC)
* - Writes to the Local Apic ICR with Delivery mode SMI.
*
* Using the local apic is a bit more tricky. According to
* AMD Family 11 Processor BKDG no destination shorthand must be
* used.
* The whole SMM initialization is quite a bit hardware specific, so
* I'm not too worried about the better of the methods at the moment
*/
/* raise an SMI interrupt */
printk(BIOS_SPEW, " ... raise SMI#\n");
outb(0x00, 0xb2);
}
uint32_t clear_tco_status(void)
{
return print_tco_status(reset_tco_status());
}
void southbridge_smm_init(void)
{
u32 smi_en;
u16 pm1_en;
u32 gpe0_en;
#if CONFIG_ELOG
/* Log events from chipset before clearing */
pch_log_state();
#endif
printk(BIOS_DEBUG, "Initializing southbridge SMI...");
pmbase = pci_read_config32(PCI_DEV(0, 0x1f, 0),
PMBASE) & 0xff80;
printk(BIOS_SPEW, " ... pmbase = 0x%04x\n", pmbase);
smi_en = inl(pmbase + SMI_EN);
if (smi_en & APMC_EN) {
printk(BIOS_INFO, "SMI# handler already enabled?\n");
return;
}
printk(BIOS_DEBUG, "\n");
dump_smi_status(reset_smi_status());
dump_pm1_status(reset_pm1_status());
dump_gpe0_status(reset_gpe0_status());
dump_alt_gp_smi_status(reset_alt_gp_smi_status());
dump_tco_status(reset_tco_status());
/* Disable GPE0 PME_B0 */
gpe0_en = inl(pmbase + GPE0_EN);
gpe0_en &= ~PME_B0_EN;
outl(gpe0_en, pmbase + GPE0_EN);
pm1_en = 0;
pm1_en |= PWRBTN_EN;
pm1_en |= GBL_EN;
outw(pm1_en, pmbase + PM1_EN);
/* Enable SMI generation:
* - on TCO events
* - on APMC writes (io 0xb2)
* - on writes to SLP_EN (sleep states)
* - on writes to GBL_RLS (bios commands)
* No SMIs:
* - on microcontroller writes (io 0x62/0x66)
*/
smi_en = 0; /* reset SMI enables */
#if 0
smi_en |= LEGACY_USB2_EN | LEGACY_USB_EN;
#endif
smi_en |= TCO_EN;
smi_en |= APMC_EN;
#if DEBUG_PERIODIC_SMIS
/* Set DEBUG_PERIODIC_SMIS in pch.h to debug using
* periodic SMIs.
*/
smi_en |= PERIODIC_EN;
#endif
smi_en |= SLP_SMI_EN;
#if 0
smi_en |= BIOS_EN;
#endif
/* The following need to be on for SMIs to happen */
smi_en |= EOS | GBL_SMI_EN;
outl(smi_en, pmbase + SMI_EN);
}
