/* disk_initialize
*
* Set up the disk.
*/
DSTATUS disk_initialize (BYTE drv) {
if (drv == 0 && sdcard_init() == 0) {
Stat &= ~STA_NOINIT;
}
return Stat;
}
void
board_init(void)
{
printf("\n\n");
printf("BWCT FSB-A920-1\n");
printf("http://www.bwct.de\n");
printf("\n");
#if defined(SDRAM_128M)
printf("AT92RM9200 180MHz 128MB\n");
#else
printf("AT92RM9200 180MHz 64MB\n");
#endif
printf("Initialising USART0\n");
USART0_Init();
printf("Initialising USART1\n");
USART1_Init();
printf("Initialising USART2\n");
USART2_Init();
printf("Initialising USART3\n");
USART3_Init();
printf("Initialising TWI\n");
EEInit();
printf("Initialising DS1672\n");
DS1672_Init();
printf("Initialising Ethernet\n");
printf("MAC %x:%x:%x:%x:%x:%x\n", mac[0],
mac[1], mac[2], mac[3], mac[4], mac[5]);
EMAC_Init();
EMAC_SetMACAddress(mac);
printf("Initialising SD-card\n");
sdcard_init();
}
void device_init(void) {
i2c_init(); // I2C bus
rtc_init(); // real time clock
sdcard_init(); // SD card
ieeehw_init(); // IEEE-488 hardware
ieee_init(8); // hardware-independent part; registers as bus
}
/*******************************************************************************
* Function Name : Read_Memory
* Description : Handle the Read operation from the microSD card.
* Input : None.
* Output : None.
* Return : None.
*******************************************************************************/
static int8_t STORAGE_Init (uint8_t lun)
{
UNUSED(lun);
LED0_OFF;
sdcard_init(sdcardConfig());
while (sdcard_poll() == 0);
LED0_ON;
return 0;
}
void
board_init(void)
{
InitEEPROM();
MacFromEE();
EMAC_Init();
EMAC_SetMACAddress(mac);
while (sdcard_init() == 0)
printf("Looking for SD card\n");
}
static esp_err_t _sdcard_init(esp_periph_handle_t self)
{
periph_sdcard_t *sdcard = esp_periph_get_data(self);
esp_err_t ret = sdcard_init(sdcard->card_detect_pin, sdcard_gpio_intr_handler, self);
if (sdcard_is_exist()) {
ret |= periph_sdcard_mount(self);
} else {
ESP_LOGE(TAG, "no sdcard detect");
}
esp_periph_start_timer(self, 1000/portTICK_RATE_MS, sdcard_timer_handler);
return ESP_OK;
}
void picture_transfer_send(unsigned char *filename) {
unsigned char *ready_msg = "S";
unsigned char length_of_send_msg_length[2];
memset(length_of_send_msg_length, '\0', sizeof(length_of_send_msg_length));
unsigned char send_msg_length[10];
memset(send_msg_length, '\0', sizeof(send_msg_length));
char * imagedata = NULL;
int imagelength;
int offset;
int result;
sdcard_init();
result = bitmap_import_image(filename, &imagedata, &imagelength, &offset);
if (result != 0) {
printf("Error with importing image\n");
return;
}
//convert imagelength to string
snprintf(send_msg_length, sizeof(send_msg_length), "%d", imagelength);
//get length of send_msg_length
snprintf(length_of_send_msg_length, sizeof(length_of_send_msg_length), "%d", strlen(send_msg_length));
//send ready message to start communication
bluetooth_send_command(ready_msg);
printf("Ready message sent!\n");
//send length of the string length of the final message
picture_transfer_send_communication(length_of_send_msg_length, sizeof(length_of_send_msg_length), STRING_LENGTH);
printf("Length of string length message sent!\n");
//send length of the final message
picture_transfer_send_communication(send_msg_length, sizeof(send_msg_length), MESSAGE_LENGTH);
printf("String length message sent!\n");
//send final message
picture_transfer_send_communication(imagedata, imagelength, FINAL);
printf("Final message sent!\n");
free(imagedata);
}
DSTATUS disk_initialize(BYTE pdrv) {
sink_sd_card_t* sink = sink_sd_card_from_pdrv(pdrv);
int ret_code = sdcard_init(sink->sd_card_regs);
int err_code = ret_code & ~SD_HCS_SET; //clear HCS flag in return value for error code
if (ret_code & SD_HCS_SET) {
sink->sdhc_card = 1;
}
if (err_code == SD_NO_ERROR) {
sink->status = 0;
} else {
sink->status = STA_NOINIT;
}
sink->sd_error_code |= err_code;
//sink->sdhc_card = 1; //TODO
return sink->status;
}
void init(void)
{
printfSupportInit();
initEEPROM();
ensureEEPROMContainsValidData();
readEEPROM();
systemState |= SYSTEM_STATE_CONFIG_LOADED;
systemInit();
//i2cSetOverclock(masterConfig.i2c_overclock);
// initialize IO (needed for all IO operations)
IOInitGlobal();
debugMode = masterConfig.debug_mode;
#ifdef USE_HARDWARE_REVISION_DETECTION
detectHardwareRevision();
#endif
// Latch active features to be used for feature() in the remainder of init().
latchActiveFeatures();
#ifdef ALIENFLIGHTF3
ledInit(hardwareRevision == AFF3_REV_1 ? false : true);
#else
ledInit(false);
#endif
LED2_ON;
#ifdef USE_EXTI
EXTIInit();
#endif
#if defined(BUTTONS)
gpio_config_t buttonAGpioConfig = {
BUTTON_A_PIN,
Mode_IPU,
Speed_2MHz
};
gpioInit(BUTTON_A_PORT, &buttonAGpioConfig);
gpio_config_t buttonBGpioConfig = {
BUTTON_B_PIN,
Mode_IPU,
Speed_2MHz
};
gpioInit(BUTTON_B_PORT, &buttonBGpioConfig);
// Check status of bind plug and exit if not active
delayMicroseconds(10); // allow GPIO configuration to settle
if (!isMPUSoftReset()) {
uint8_t secondsRemaining = 5;
bool bothButtonsHeld;
do {
bothButtonsHeld = !digitalIn(BUTTON_A_PORT, BUTTON_A_PIN) && !digitalIn(BUTTON_B_PORT, BUTTON_B_PIN);
if (bothButtonsHeld) {
if (--secondsRemaining == 0) {
resetEEPROM();
systemReset();
}
delay(1000);
LED0_TOGGLE;
}
} while (bothButtonsHeld);
}
#endif
#ifdef SPEKTRUM_BIND
if (feature(FEATURE_RX_SERIAL)) {
switch (masterConfig.rxConfig.serialrx_provider) {
case SERIALRX_SPEKTRUM1024:
case SERIALRX_SPEKTRUM2048:
// Spektrum satellite binding if enabled on startup.
// Must be called before that 100ms sleep so that we don't lose satellite's binding window after startup.
// The rest of Spektrum initialization will happen later - via spektrumInit()
spektrumBind(&masterConfig.rxConfig);
break;
}
}
#endif
delay(100);
timerInit(); // timer must be initialized before any channel is allocated
dmaInit();
#if defined(AVOID_UART1_FOR_PWM_PPM)
serialInit(&masterConfig.serialConfig, feature(FEATURE_SOFTSERIAL),
feature(FEATURE_RX_PPM) || feature(FEATURE_RX_PARALLEL_PWM) ? SERIAL_PORT_USART1 : SERIAL_PORT_NONE);
#elif defined(AVOID_UART2_FOR_PWM_PPM)
serialInit(&masterConfig.serialConfig, feature(FEATURE_SOFTSERIAL),
feature(FEATURE_RX_PPM) || feature(FEATURE_RX_PARALLEL_PWM) ? SERIAL_PORT_USART2 : SERIAL_PORT_NONE);
#elif defined(AVOID_UART3_FOR_PWM_PPM)
serialInit(&masterConfig.serialConfig, feature(FEATURE_SOFTSERIAL),
feature(FEATURE_RX_PPM) || feature(FEATURE_RX_PARALLEL_PWM) ? SERIAL_PORT_USART3 : SERIAL_PORT_NONE);
#else
serialInit(&masterConfig.serialConfig, feature(FEATURE_SOFTSERIAL), SERIAL_PORT_NONE);
#endif
#ifdef USE_SERVOS
mixerInit(masterConfig.mixerMode, masterConfig.customMotorMixer, masterConfig.customServoMixer);
#else
mixerInit(masterConfig.mixerMode, masterConfig.customMotorMixer);
#endif
drv_pwm_config_t pwm_params;
memset(&pwm_params, 0, sizeof(pwm_params));
#ifdef SONAR
if (feature(FEATURE_SONAR)) {
const sonarHardware_t *sonarHardware = sonarGetHardwareConfiguration(masterConfig.batteryConfig.currentMeterType);
if (sonarHardware) {
pwm_params.useSonar = true;
pwm_params.sonarIOConfig.triggerTag = sonarHardware->triggerTag;
pwm_params.sonarIOConfig.echoTag = sonarHardware->echoTag;
}
}
#endif
// when using airplane/wing mixer, servo/motor outputs are remapped
if (masterConfig.mixerMode == MIXER_AIRPLANE || masterConfig.mixerMode == MIXER_FLYING_WING || masterConfig.mixerMode == MIXER_CUSTOM_AIRPLANE)
pwm_params.airplane = true;
else
pwm_params.airplane = false;
#if defined(USE_UART2) && defined(STM32F10X)
pwm_params.useUART2 = doesConfigurationUsePort(SERIAL_PORT_USART2);
#endif
#ifdef STM32F303xC
pwm_params.useUART2 = doesConfigurationUsePort(SERIAL_PORT_USART2);
pwm_params.useUART3 = doesConfigurationUsePort(SERIAL_PORT_USART3);
#endif
#if defined(USE_UART2) && defined(STM32F40_41xxx)
pwm_params.useUART2 = doesConfigurationUsePort(SERIAL_PORT_USART2);
#endif
#if defined(USE_UART6) && defined(STM32F40_41xxx)
pwm_params.useUART6 = doesConfigurationUsePort(SERIAL_PORT_USART6);
#endif
pwm_params.useVbat = feature(FEATURE_VBAT);
pwm_params.useSoftSerial = feature(FEATURE_SOFTSERIAL);
pwm_params.useParallelPWM = feature(FEATURE_RX_PARALLEL_PWM);
pwm_params.useRSSIADC = feature(FEATURE_RSSI_ADC);
pwm_params.useCurrentMeterADC = feature(FEATURE_CURRENT_METER)
&& masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC;
pwm_params.useLEDStrip = feature(FEATURE_LED_STRIP);
pwm_params.usePPM = feature(FEATURE_RX_PPM);
pwm_params.useSerialRx = feature(FEATURE_RX_SERIAL);
#ifdef USE_SERVOS
pwm_params.useServos = isMixerUsingServos();
pwm_params.useChannelForwarding = feature(FEATURE_CHANNEL_FORWARDING);
pwm_params.servoCenterPulse = masterConfig.escAndServoConfig.servoCenterPulse;
pwm_params.servoPwmRate = masterConfig.servo_pwm_rate;
#endif
bool use_unsyncedPwm = masterConfig.use_unsyncedPwm || masterConfig.motor_pwm_protocol == PWM_TYPE_CONVENTIONAL || masterConfig.motor_pwm_protocol == PWM_TYPE_BRUSHED;
// Configurator feature abused for enabling Fast PWM
pwm_params.useFastPwm = (masterConfig.motor_pwm_protocol != PWM_TYPE_CONVENTIONAL && masterConfig.motor_pwm_protocol != PWM_TYPE_BRUSHED);
pwm_params.pwmProtocolType = masterConfig.motor_pwm_protocol;
pwm_params.motorPwmRate = use_unsyncedPwm ? masterConfig.motor_pwm_rate : 0;
pwm_params.idlePulse = masterConfig.escAndServoConfig.mincommand;
if (feature(FEATURE_3D))
pwm_params.idlePulse = masterConfig.flight3DConfig.neutral3d;
if (masterConfig.motor_pwm_protocol == PWM_TYPE_BRUSHED) {
featureClear(FEATURE_3D);
pwm_params.idlePulse = 0; // brushed motors
}
#ifdef CC3D
pwm_params.useBuzzerP6 = masterConfig.use_buzzer_p6 ? true : false;
#endif
#ifndef SKIP_RX_PWM_PPM
pwmRxInit(masterConfig.inputFilteringMode);
#endif
// pwmInit() needs to be called as soon as possible for ESC compatibility reasons
pwmOutputConfiguration_t *pwmOutputConfiguration = pwmInit(&pwm_params);
mixerUsePWMOutputConfiguration(pwmOutputConfiguration, use_unsyncedPwm);
systemState |= SYSTEM_STATE_MOTORS_READY;
#ifdef BEEPER
beeperConfig_t beeperConfig = {
.ioTag = IO_TAG(BEEPER),
#ifdef BEEPER_INVERTED
.isOD = false,
.isInverted = true
#else
.isOD = true,
.isInverted = false
#endif
};
#ifdef NAZE
if (hardwareRevision >= NAZE32_REV5) {
// naze rev4 and below used opendrain to PNP for buzzer. Rev5 and above use PP to NPN.
beeperConfig.isOD = false;
beeperConfig.isInverted = true;
}
#endif
/* temp until PGs are implemented. */
#ifdef BLUEJAYF4
if (hardwareRevision <= BJF4_REV2) {
beeperConfig.ioTag = IO_TAG(BEEPER_OPT);
}
#endif
#ifdef CC3D
if (masterConfig.use_buzzer_p6 == 1)
beeperConfig.ioTag = IO_TAG(BEEPER_OPT);
#endif
beeperInit(&beeperConfig);
#endif
#ifdef INVERTER
initInverter();
#endif
#ifdef USE_BST
bstInit(BST_DEVICE);
#endif
#ifdef USE_SPI
#ifdef USE_SPI_DEVICE_1
spiInit(SPIDEV_1);
#endif
#ifdef USE_SPI_DEVICE_2
spiInit(SPIDEV_2);
#endif
#ifdef USE_SPI_DEVICE_3
#ifdef ALIENFLIGHTF3
if (hardwareRevision == AFF3_REV_2) {
spiInit(SPIDEV_3);
}
#else
spiInit(SPIDEV_3);
#endif
#endif
#endif
#ifdef VTX
vtxInit();
#endif
#ifdef USE_HARDWARE_REVISION_DETECTION
updateHardwareRevision();
#endif
#if defined(NAZE)
if (hardwareRevision == NAZE32_SP) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
} else {
serialRemovePort(SERIAL_PORT_USART3);
}
#endif
#if defined(SPRACINGF3) && defined(SONAR) && defined(USE_SOFTSERIAL2)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
}
#endif
#if defined(SPRACINGF3MINI) || defined(OMNIBUS) || defined(X_RACERSPI)
#if defined(SONAR) && defined(USE_SOFTSERIAL1)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL1);
}
#endif
#endif
#ifdef USE_I2C
#if defined(NAZE)
if (hardwareRevision != NAZE32_SP) {
i2cInit(I2C_DEVICE);
} else {
if (!doesConfigurationUsePort(SERIAL_PORT_USART3)) {
i2cInit(I2C_DEVICE);
}
}
#elif defined(CC3D)
if (!doesConfigurationUsePort(SERIAL_PORT_USART3)) {
i2cInit(I2C_DEVICE);
}
#else
i2cInit(I2C_DEVICE);
#endif
#endif
#ifdef USE_ADC
drv_adc_config_t adc_params;
adc_params.enableVBat = feature(FEATURE_VBAT);
adc_params.enableRSSI = feature(FEATURE_RSSI_ADC);
adc_params.enableCurrentMeter = feature(FEATURE_CURRENT_METER);
adc_params.enableExternal1 = false;
#ifdef OLIMEXINO
adc_params.enableExternal1 = true;
#endif
#ifdef NAZE
// optional ADC5 input on rev.5 hardware
adc_params.enableExternal1 = (hardwareRevision >= NAZE32_REV5);
#endif
adcInit(&adc_params);
#endif
initBoardAlignment(&masterConfig.boardAlignment);
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
displayInit(&masterConfig.rxConfig);
}
#endif
#ifdef USE_RTC6705
if (feature(FEATURE_VTX)) {
rtc6705_soft_spi_init();
current_vtx_channel = masterConfig.vtx_channel;
rtc6705_soft_spi_set_channel(vtx_freq[current_vtx_channel]);
rtc6705_soft_spi_set_rf_power(masterConfig.vtx_power);
}
#endif
#ifdef OSD
if (feature(FEATURE_OSD)) {
osdInit();
}
#endif
if (!sensorsAutodetect(&masterConfig.sensorAlignmentConfig,
masterConfig.acc_hardware,
masterConfig.mag_hardware,
masterConfig.baro_hardware,
masterConfig.mag_declination,
masterConfig.gyro_lpf,
masterConfig.gyro_sync_denom)) {
// if gyro was not detected due to whatever reason, we give up now.
failureMode(FAILURE_MISSING_ACC);
}
systemState |= SYSTEM_STATE_SENSORS_READY;
LED1_ON;
LED0_OFF;
LED2_OFF;
for (int i = 0; i < 10; i++) {
LED1_TOGGLE;
LED0_TOGGLE;
delay(25);
if (!(getBeeperOffMask() & (1 << (BEEPER_SYSTEM_INIT - 1)))) BEEP_ON;
delay(25);
BEEP_OFF;
}
LED0_OFF;
LED1_OFF;
#ifdef MAG
if (sensors(SENSOR_MAG))
compassInit();
#endif
imuInit();
mspInit(&masterConfig.serialConfig);
#ifdef USE_CLI
cliInit(&masterConfig.serialConfig);
#endif
failsafeInit(&masterConfig.rxConfig, masterConfig.flight3DConfig.deadband3d_throttle);
rxInit(&masterConfig.rxConfig, masterConfig.modeActivationConditions);
#ifdef GPS
if (feature(FEATURE_GPS)) {
gpsInit(
&masterConfig.serialConfig,
&masterConfig.gpsConfig
);
navigationInit(
&masterConfig.gpsProfile,
¤tProfile->pidProfile
);
}
#endif
#ifdef SONAR
if (feature(FEATURE_SONAR)) {
sonarInit();
}
#endif
#ifdef LED_STRIP
ledStripInit(masterConfig.ledConfigs, masterConfig.colors, masterConfig.modeColors, &masterConfig.specialColors);
if (feature(FEATURE_LED_STRIP)) {
ledStripEnable();
}
#endif
#ifdef TELEMETRY
if (feature(FEATURE_TELEMETRY)) {
telemetryInit();
}
#endif
#ifdef USB_CABLE_DETECTION
usbCableDetectInit();
#endif
#ifdef TRANSPONDER
if (feature(FEATURE_TRANSPONDER)) {
transponderInit(masterConfig.transponderData);
transponderEnable();
transponderStartRepeating();
systemState |= SYSTEM_STATE_TRANSPONDER_ENABLED;
}
#endif
#ifdef USE_FLASHFS
#ifdef NAZE
if (hardwareRevision == NAZE32_REV5) {
m25p16_init(IOTAG_NONE);
}
#elif defined(USE_FLASH_M25P16)
m25p16_init(IOTAG_NONE);
#endif
flashfsInit();
#endif
#ifdef USE_SDCARD
bool sdcardUseDMA = false;
sdcardInsertionDetectInit();
#ifdef SDCARD_DMA_CHANNEL_TX
#if defined(LED_STRIP) && defined(WS2811_DMA_CHANNEL)
// Ensure the SPI Tx DMA doesn't overlap with the led strip
#ifdef STM32F4
sdcardUseDMA = !feature(FEATURE_LED_STRIP) || SDCARD_DMA_CHANNEL_TX != WS2811_DMA_STREAM;
#else
sdcardUseDMA = !feature(FEATURE_LED_STRIP) || SDCARD_DMA_CHANNEL_TX != WS2811_DMA_CHANNEL;
#endif
#else
sdcardUseDMA = true;
#endif
#endif
sdcard_init(sdcardUseDMA);
afatfs_init();
#endif
if (masterConfig.gyro_lpf > 0 && masterConfig.gyro_lpf < 7) {
masterConfig.pid_process_denom = 1; // When gyro set to 1khz always set pid speed 1:1 to sampling speed
masterConfig.gyro_sync_denom = 1;
}
setTargetPidLooptime(gyro.targetLooptime * masterConfig.pid_process_denom); // Initialize pid looptime
#ifdef BLACKBOX
initBlackbox();
#endif
if (masterConfig.mixerMode == MIXER_GIMBAL) {
accSetCalibrationCycles(CALIBRATING_ACC_CYCLES);
}
gyroSetCalibrationCycles();
#ifdef BARO
baroSetCalibrationCycles(CALIBRATING_BARO_CYCLES);
#endif
// start all timers
// TODO - not implemented yet
timerStart();
ENABLE_STATE(SMALL_ANGLE);
DISABLE_ARMING_FLAG(PREVENT_ARMING);
#ifdef SOFTSERIAL_LOOPBACK
// FIXME this is a hack, perhaps add a FUNCTION_LOOPBACK to support it properly
loopbackPort = (serialPort_t*)&(softSerialPorts[0]);
if (!loopbackPort->vTable) {
loopbackPort = openSoftSerial(0, NULL, 19200, SERIAL_NOT_INVERTED);
}
serialPrint(loopbackPort, "LOOPBACK\r\n");
#endif
// Now that everything has powered up the voltage and cell count be determined.
if (feature(FEATURE_VBAT | FEATURE_CURRENT_METER))
batteryInit(&masterConfig.batteryConfig);
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
#ifdef USE_OLED_GPS_DEBUG_PAGE_ONLY
displayShowFixedPage(PAGE_GPS);
#else
displayResetPageCycling();
displayEnablePageCycling();
#endif
}
#endif
#ifdef CJMCU
LED2_ON;
#endif
// Latch active features AGAIN since some may be modified by init().
latchActiveFeatures();
motorControlEnable = true;
systemState |= SYSTEM_STATE_READY;
}
#ifdef SOFTSERIAL_LOOPBACK
void processLoopback(void) {
if (loopbackPort) {
uint8_t bytesWaiting;
while ((bytesWaiting = serialRxBytesWaiting(loopbackPort))) {
uint8_t b = serialRead(loopbackPort);
serialWrite(loopbackPort, b);
};
}
}
#else
#define processLoopback()
#endif
void main_init(void)
{
init();
/* Setup scheduler */
schedulerInit();
rescheduleTask(TASK_GYROPID, gyro.targetLooptime);
setTaskEnabled(TASK_GYROPID, true);
if (sensors(SENSOR_ACC)) {
setTaskEnabled(TASK_ACCEL, true);
switch (gyro.targetLooptime) { // Switch statement kept in place to change acc rates in the future
case 500:
case 375:
case 250:
case 125:
accTargetLooptime = 1000;
break;
default:
case 1000:
#ifdef STM32F10X
accTargetLooptime = 1000;
#else
accTargetLooptime = 1000;
#endif
}
rescheduleTask(TASK_ACCEL, accTargetLooptime);
}
setTaskEnabled(TASK_ATTITUDE, sensors(SENSOR_ACC));
setTaskEnabled(TASK_SERIAL, true);
#ifdef BEEPER
setTaskEnabled(TASK_BEEPER, true);
#endif
setTaskEnabled(TASK_BATTERY, feature(FEATURE_VBAT) || feature(FEATURE_CURRENT_METER));
setTaskEnabled(TASK_RX, true);
#ifdef GPS
setTaskEnabled(TASK_GPS, feature(FEATURE_GPS));
#endif
#ifdef MAG
setTaskEnabled(TASK_COMPASS, sensors(SENSOR_MAG));
#if defined(USE_SPI) && defined(USE_MAG_AK8963)
// fixme temporary solution for AK6983 via slave I2C on MPU9250
rescheduleTask(TASK_COMPASS, 1000000 / 40);
#endif
#endif
#ifdef BARO
setTaskEnabled(TASK_BARO, sensors(SENSOR_BARO));
#endif
#ifdef SONAR
setTaskEnabled(TASK_SONAR, sensors(SENSOR_SONAR));
#endif
#if defined(BARO) || defined(SONAR)
setTaskEnabled(TASK_ALTITUDE, sensors(SENSOR_BARO) || sensors(SENSOR_SONAR));
#endif
#ifdef DISPLAY
setTaskEnabled(TASK_DISPLAY, feature(FEATURE_DISPLAY));
#endif
#ifdef TELEMETRY
setTaskEnabled(TASK_TELEMETRY, feature(FEATURE_TELEMETRY));
// Reschedule telemetry to 500hz for Jeti Exbus
if (feature(FEATURE_TELEMETRY) || masterConfig.rxConfig.serialrx_provider == SERIALRX_JETIEXBUS) rescheduleTask(TASK_TELEMETRY, 2000);
#endif
#ifdef LED_STRIP
setTaskEnabled(TASK_LEDSTRIP, feature(FEATURE_LED_STRIP));
#endif
#ifdef TRANSPONDER
setTaskEnabled(TASK_TRANSPONDER, feature(FEATURE_TRANSPONDER));
#endif
#ifdef OSD
setTaskEnabled(TASK_OSD, feature(FEATURE_OSD));
#endif
#ifdef USE_BST
setTaskEnabled(TASK_BST_MASTER_PROCESS, true);
#endif
}
void init(void)
{
drv_pwm_config_t pwm_params;
printfSupportInit();
initEEPROM();
ensureEEPROMContainsValidData();
readEEPROM();
systemState |= SYSTEM_STATE_CONFIG_LOADED;
#ifdef STM32F303
// start fpu
SCB->CPACR = (0x3 << (10*2)) | (0x3 << (11*2));
#endif
#ifdef STM32F303xC
SetSysClock();
#endif
#ifdef STM32F10X
// Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers
// Configure the Flash Latency cycles and enable prefetch buffer
SetSysClock(systemConfig()->emf_avoidance);
#endif
i2cSetOverclock(systemConfig()->i2c_highspeed);
systemInit();
#ifdef USE_HARDWARE_REVISION_DETECTION
detectHardwareRevision();
#endif
// Latch active features to be used for feature() in the remainder of init().
latchActiveFeatures();
// initialize IO (needed for all IO operations)
IOInitGlobal();
debugMode = debugConfig()->debug_mode;
#ifdef USE_EXTI
EXTIInit();
#endif
#ifdef ALIENFLIGHTF3
if (hardwareRevision == AFF3_REV_1) {
ledInit(false);
} else {
ledInit(true);
}
#else
ledInit(false);
#endif
#ifdef BEEPER
beeperConfig_t beeperConfig = {
.gpioPeripheral = BEEP_PERIPHERAL,
.gpioPin = BEEP_PIN,
.gpioPort = BEEP_GPIO,
#ifdef BEEPER_INVERTED
.gpioMode = Mode_Out_PP,
.isInverted = true
#else
.gpioMode = Mode_Out_OD,
.isInverted = false
#endif
};
#ifdef NAZE
if (hardwareRevision >= NAZE32_REV5) {
// naze rev4 and below used opendrain to PNP for buzzer. Rev5 and above use PP to NPN.
beeperConfig.gpioMode = Mode_Out_PP;
beeperConfig.isInverted = true;
}
#endif
beeperInit(&beeperConfig);
#endif
#ifdef BUTTONS
buttonsInit();
if (!isMPUSoftReset()) {
buttonsHandleColdBootButtonPresses();
}
#endif
#ifdef SPEKTRUM_BIND
if (feature(FEATURE_RX_SERIAL)) {
switch (rxConfig()->serialrx_provider) {
case SERIALRX_SPEKTRUM1024:
case SERIALRX_SPEKTRUM2048:
// Spektrum satellite binding if enabled on startup.
// Must be called before that 100ms sleep so that we don't lose satellite's binding window after startup.
// The rest of Spektrum initialization will happen later - via spektrumInit()
spektrumBind(rxConfig());
break;
}
}
#endif
delay(100);
timerInit(); // timer must be initialized before any channel is allocated
dmaInit();
serialInit(feature(FEATURE_SOFTSERIAL));
mixerInit(customMotorMixer(0));
#ifdef USE_SERVOS
mixerInitServos(customServoMixer(0));
#endif
memset(&pwm_params, 0, sizeof(pwm_params));
#ifdef SONAR
const sonarHardware_t *sonarHardware = NULL;
sonarGPIOConfig_t sonarGPIOConfig;
if (feature(FEATURE_SONAR)) {
bool usingCurrentMeterIOPins = (feature(FEATURE_AMPERAGE_METER) && batteryConfig()->amperageMeterSource == AMPERAGE_METER_ADC);
sonarHardware = sonarGetHardwareConfiguration(usingCurrentMeterIOPins);
sonarGPIOConfig.triggerGPIO = sonarHardware->trigger_gpio;
sonarGPIOConfig.triggerPin = sonarHardware->trigger_pin;
sonarGPIOConfig.echoGPIO = sonarHardware->echo_gpio;
sonarGPIOConfig.echoPin = sonarHardware->echo_pin;
pwm_params.sonarGPIOConfig = &sonarGPIOConfig;
}
#endif
// when using airplane/wing mixer, servo/motor outputs are remapped
if (mixerConfig()->mixerMode == MIXER_AIRPLANE || mixerConfig()->mixerMode == MIXER_FLYING_WING || mixerConfig()->mixerMode == MIXER_CUSTOM_AIRPLANE)
pwm_params.airplane = true;
else
pwm_params.airplane = false;
#if defined(USE_UART2) && defined(STM32F10X)
pwm_params.useUART2 = doesConfigurationUsePort(SERIAL_PORT_UART2);
#endif
#if defined(USE_UART3)
pwm_params.useUART3 = doesConfigurationUsePort(SERIAL_PORT_UART3);
#endif
#if defined(USE_UART4)
pwm_params.useUART4 = doesConfigurationUsePort(SERIAL_PORT_UART4);
#endif
#if defined(USE_UART5)
pwm_params.useUART5 = doesConfigurationUsePort(SERIAL_PORT_UART5);
#endif
pwm_params.useVbat = feature(FEATURE_VBAT);
pwm_params.useSoftSerial = feature(FEATURE_SOFTSERIAL);
pwm_params.useParallelPWM = feature(FEATURE_RX_PARALLEL_PWM);
pwm_params.useRSSIADC = feature(FEATURE_RSSI_ADC);
pwm_params.useCurrentMeterADC = (
feature(FEATURE_AMPERAGE_METER)
&& batteryConfig()->amperageMeterSource == AMPERAGE_METER_ADC
);
pwm_params.useLEDStrip = feature(FEATURE_LED_STRIP);
pwm_params.usePPM = feature(FEATURE_RX_PPM);
pwm_params.useSerialRx = feature(FEATURE_RX_SERIAL);
#ifdef SONAR
pwm_params.useSonar = feature(FEATURE_SONAR);
#endif
#ifdef USE_SERVOS
pwm_params.useServos = isMixerUsingServos();
pwm_params.useChannelForwarding = feature(FEATURE_CHANNEL_FORWARDING);
pwm_params.servoCenterPulse = servoConfig()->servoCenterPulse;
pwm_params.servoPwmRate = servoConfig()->servo_pwm_rate;
#endif
pwm_params.useOneshot = feature(FEATURE_ONESHOT125);
pwm_params.motorPwmRate = motorConfig()->motor_pwm_rate;
pwm_params.idlePulse = calculateMotorOff();
if (pwm_params.motorPwmRate > 500)
pwm_params.idlePulse = 0; // brushed motors
pwmRxInit();
// pwmInit() needs to be called as soon as possible for ESC compatibility reasons
pwmIOConfiguration_t *pwmIOConfiguration = pwmInit(&pwm_params);
mixerUsePWMIOConfiguration(pwmIOConfiguration);
#ifdef DEBUG_PWM_CONFIGURATION
debug[2] = pwmIOConfiguration->pwmInputCount;
debug[3] = pwmIOConfiguration->ppmInputCount;
#endif
if (!feature(FEATURE_ONESHOT125))
motorControlEnable = true;
systemState |= SYSTEM_STATE_MOTORS_READY;
#ifdef INVERTER
initInverter();
#endif
#ifdef USE_SPI
spiInit(SPI1);
spiInit(SPI2);
#ifdef STM32F303xC
#ifdef ALIENFLIGHTF3
if (hardwareRevision == AFF3_REV_2) {
spiInit(SPI3);
}
#else
spiInit(SPI3);
#endif
#endif
#endif
#ifdef USE_HARDWARE_REVISION_DETECTION
updateHardwareRevision();
#endif
#if defined(NAZE)
if (hardwareRevision == NAZE32_SP) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
} else {
serialRemovePort(SERIAL_PORT_UART3);
}
#endif
#if defined(SPRACINGF3) && defined(SONAR) && defined(USE_SOFTSERIAL2)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
}
#endif
#if defined(SPRACINGF3MINI) && defined(SONAR) && defined(USE_SOFTSERIAL1)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL1);
}
#endif
#ifdef USE_I2C
#if defined(NAZE)
if (hardwareRevision != NAZE32_SP) {
i2cInit(I2C_DEVICE);
} else {
if (!doesConfigurationUsePort(SERIAL_PORT_UART3)) {
i2cInit(I2C_DEVICE);
}
}
#elif defined(CC3D)
if (!doesConfigurationUsePort(SERIAL_PORT_UART3)) {
i2cInit(I2C_DEVICE);
}
#else
i2cInit(I2C_DEVICE);
#endif
#endif
#ifdef USE_ADC
drv_adc_config_t adc_params;
adc_params.channelMask = 0;
#ifdef ADC_BATTERY
adc_params.channelMask = (feature(FEATURE_VBAT) ? ADC_CHANNEL_MASK(ADC_BATTERY) : 0);
#endif
#ifdef ADC_RSSI
adc_params.channelMask |= (feature(FEATURE_RSSI_ADC) ? ADC_CHANNEL_MASK(ADC_RSSI) : 0);
#endif
#ifdef ADC_AMPERAGE
adc_params.channelMask |= (feature(FEATURE_AMPERAGE_METER) ? ADC_CHANNEL_MASK(ADC_AMPERAGE) : 0);
#endif
#ifdef ADC_POWER_12V
adc_params.channelMask |= ADC_CHANNEL_MASK(ADC_POWER_12V);
#endif
#ifdef ADC_POWER_5V
adc_params.channelMask |= ADC_CHANNEL_MASK(ADC_POWER_5V);
#endif
#ifdef ADC_POWER_3V
adc_params.channelMask |= ADC_CHANNEL_MASK(ADC_POWER_3V);
#endif
#ifdef NAZE
// optional ADC5 input on rev.5 hardware
adc_params.channelMask |= (hardwareRevision >= NAZE32_REV5) ? ADC_CHANNEL_MASK(ADC_EXTERNAL) : 0;
#endif
adcInit(&adc_params);
#endif
initBoardAlignment();
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
displayInit();
}
#endif
#ifdef NAZE
if (hardwareRevision < NAZE32_REV5) {
gyroConfig()->gyro_sync = 0;
}
#endif
if (!sensorsAutodetect()) {
// if gyro was not detected due to whatever reason, we give up now.
failureMode(FAILURE_MISSING_ACC);
}
systemState |= SYSTEM_STATE_SENSORS_READY;
flashLedsAndBeep();
mspInit();
mspSerialInit();
const uint16_t pidPeriodUs = US_FROM_HZ(gyro.sampleFrequencyHz);
pidSetTargetLooptime(pidPeriodUs * gyroConfig()->pid_process_denom);
pidInitFilters(pidProfile());
#ifdef USE_SERVOS
mixerInitialiseServoFiltering(targetPidLooptime);
#endif
imuInit();
#ifdef USE_CLI
cliInit();
#endif
failsafeInit();
rxInit(modeActivationProfile()->modeActivationConditions);
#ifdef GPS
if (feature(FEATURE_GPS)) {
gpsInit();
navigationInit(pidProfile());
}
#endif
#ifdef SONAR
if (feature(FEATURE_SONAR)) {
sonarInit(sonarHardware);
}
#endif
#ifdef LED_STRIP
ledStripInit();
if (feature(FEATURE_LED_STRIP)) {
ledStripEnable();
}
#endif
#ifdef TELEMETRY
if (feature(FEATURE_TELEMETRY)) {
telemetryInit();
}
#endif
#ifdef USB_CABLE_DETECTION
usbCableDetectInit();
#endif
#ifdef TRANSPONDER
if (feature(FEATURE_TRANSPONDER)) {
transponderInit(transponderConfig()->data);
transponderEnable();
transponderStartRepeating();
systemState |= SYSTEM_STATE_TRANSPONDER_ENABLED;
}
#endif
#ifdef USE_FLASHFS
#ifdef NAZE
if (hardwareRevision == NAZE32_REV5) {
m25p16_init();
}
#elif defined(USE_FLASH_M25P16)
m25p16_init();
#endif
flashfsInit();
#endif
#ifdef USE_SDCARD
bool sdcardUseDMA = false;
sdcardInsertionDetectInit();
#ifdef SDCARD_DMA_CHANNEL_TX
#if defined(LED_STRIP) && defined(WS2811_DMA_CHANNEL)
// Ensure the SPI Tx DMA doesn't overlap with the led strip
sdcardUseDMA = !feature(FEATURE_LED_STRIP) || SDCARD_DMA_CHANNEL_TX != WS2811_DMA_CHANNEL;
#else
sdcardUseDMA = true;
#endif
#endif
sdcard_init(sdcardUseDMA);
afatfs_init();
#endif
#ifdef BLACKBOX
initBlackbox();
#endif
if (mixerConfig()->mixerMode == MIXER_GIMBAL) {
accSetCalibrationCycles(CALIBRATING_ACC_CYCLES);
}
gyroSetCalibrationCycles(CALIBRATING_GYRO_CYCLES);
#ifdef BARO
baroSetCalibrationCycles(CALIBRATING_BARO_CYCLES);
#endif
// start all timers
// TODO - not implemented yet
timerStart();
ENABLE_STATE(SMALL_ANGLE);
DISABLE_ARMING_FLAG(PREVENT_ARMING);
#ifdef SOFTSERIAL_LOOPBACK
// FIXME this is a hack, perhaps add a FUNCTION_LOOPBACK to support it properly
loopbackPort = (serialPort_t*)&(softSerialPorts[0]);
if (!loopbackPort->vTable) {
loopbackPort = openSoftSerial(0, NULL, 19200, SERIAL_NOT_INVERTED);
}
serialPrint(loopbackPort, "LOOPBACK\r\n");
#endif
if (feature(FEATURE_VBAT)) {
// Now that everything has powered up the voltage and cell count be determined.
voltageMeterInit();
batteryInit();
}
if (feature(FEATURE_AMPERAGE_METER)) {
amperageMeterInit();
}
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
#ifdef USE_OLED_GPS_DEBUG_PAGE_ONLY
displayShowFixedPage(PAGE_GPS);
#else
displayResetPageCycling();
displayEnablePageCycling();
#endif
}
#endif
#ifdef CJMCU
LED2_ON;
#endif
// Latch active features AGAIN since some may be modified by init().
latchActiveFeatures();
motorControlEnable = true;
systemState |= SYSTEM_STATE_READY;
}
#ifdef SOFTSERIAL_LOOPBACK
void processLoopback(void) {
if (loopbackPort) {
uint8_t bytesWaiting;
while ((bytesWaiting = serialRxBytesWaiting(loopbackPort))) {
uint8_t b = serialRead(loopbackPort);
serialWrite(loopbackPort, b);
};
}
}
#else
#define processLoopback()
#endif
void configureScheduler(void)
{
schedulerInit();
setTaskEnabled(TASK_SYSTEM, true);
uint16_t gyroPeriodUs = US_FROM_HZ(gyro.sampleFrequencyHz);
rescheduleTask(TASK_GYRO, gyroPeriodUs);
setTaskEnabled(TASK_GYRO, true);
rescheduleTask(TASK_PID, gyroPeriodUs);
setTaskEnabled(TASK_PID, true);
if (sensors(SENSOR_ACC)) {
setTaskEnabled(TASK_ACCEL, true);
}
setTaskEnabled(TASK_ATTITUDE, sensors(SENSOR_ACC));
setTaskEnabled(TASK_SERIAL, true);
#ifdef BEEPER
setTaskEnabled(TASK_BEEPER, true);
#endif
setTaskEnabled(TASK_BATTERY, feature(FEATURE_VBAT) || feature(FEATURE_AMPERAGE_METER));
setTaskEnabled(TASK_RX, true);
#ifdef GPS
setTaskEnabled(TASK_GPS, feature(FEATURE_GPS));
#endif
#ifdef MAG
setTaskEnabled(TASK_COMPASS, sensors(SENSOR_MAG));
#if defined(MPU6500_SPI_INSTANCE) && defined(USE_MAG_AK8963)
// fixme temporary solution for AK6983 via slave I2C on MPU9250
rescheduleTask(TASK_COMPASS, 1000000 / 40);
#endif
#endif
#ifdef BARO
setTaskEnabled(TASK_BARO, sensors(SENSOR_BARO));
#endif
#ifdef SONAR
setTaskEnabled(TASK_SONAR, sensors(SENSOR_SONAR));
#endif
#if defined(BARO) || defined(SONAR)
setTaskEnabled(TASK_ALTITUDE, sensors(SENSOR_BARO) || sensors(SENSOR_SONAR));
#endif
#ifdef DISPLAY
setTaskEnabled(TASK_DISPLAY, feature(FEATURE_DISPLAY));
#endif
#ifdef TELEMETRY
setTaskEnabled(TASK_TELEMETRY, feature(FEATURE_TELEMETRY));
#endif
#ifdef LED_STRIP
setTaskEnabled(TASK_LEDSTRIP, feature(FEATURE_LED_STRIP));
#endif
#ifdef TRANSPONDER
setTaskEnabled(TASK_TRANSPONDER, feature(FEATURE_TRANSPONDER));
#endif
}
void init(void)
{
drv_pwm_config_t pwm_params;
printfSupportInit();
initEEPROM();
ensureEEPROMContainsValidData();
readEEPROM();
systemState |= SYSTEM_STATE_CONFIG_LOADED;
#ifdef STM32F303
// start fpu
SCB->CPACR = (0x3 << (10*2)) | (0x3 << (11*2));
#endif
#ifdef STM32F303xC
SetSysClock();
#endif
#ifdef STM32F10X
// Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers
// Configure the Flash Latency cycles and enable prefetch buffer
SetSysClock(masterConfig.emf_avoidance);
#endif
i2cSetOverclock(masterConfig.i2c_highspeed);
#ifdef USE_HARDWARE_REVISION_DETECTION
detectHardwareRevision();
#endif
systemInit();
// Latch active features to be used for feature() in the remainder of init().
latchActiveFeatures();
ledInit();
#ifdef BEEPER
beeperConfig_t beeperConfig = {
.gpioPeripheral = BEEP_PERIPHERAL,
.gpioPin = BEEP_PIN,
.gpioPort = BEEP_GPIO,
#ifdef BEEPER_INVERTED
.gpioMode = Mode_Out_PP,
.isInverted = true
#else
.gpioMode = Mode_Out_OD,
.isInverted = false
#endif
};
#ifdef NAZE
if (hardwareRevision >= NAZE32_REV5) {
// naze rev4 and below used opendrain to PNP for buzzer. Rev5 and above use PP to NPN.
beeperConfig.gpioMode = Mode_Out_PP;
beeperConfig.isInverted = true;
}
#endif
beeperInit(&beeperConfig);
#endif
#ifdef BUTTONS
buttonsInit();
if (!isMPUSoftReset()) {
buttonsHandleColdBootButtonPresses();
}
#endif
#ifdef SPEKTRUM_BIND
if (feature(FEATURE_RX_SERIAL)) {
switch (masterConfig.rxConfig.serialrx_provider) {
case SERIALRX_SPEKTRUM1024:
case SERIALRX_SPEKTRUM2048:
// Spektrum satellite binding if enabled on startup.
// Must be called before that 100ms sleep so that we don't lose satellite's binding window after startup.
// The rest of Spektrum initialization will happen later - via spektrumInit()
spektrumBind(&masterConfig.rxConfig);
break;
}
}
#endif
delay(100);
timerInit(); // timer must be initialized before any channel is allocated
dmaInit();
serialInit(&masterConfig.serialConfig, feature(FEATURE_SOFTSERIAL));
#ifdef USE_SERVOS
mixerInit(masterConfig.mixerMode, masterConfig.customMotorMixer, masterConfig.customServoMixer);
#else
mixerInit(masterConfig.mixerMode, masterConfig.customMotorMixer);
#endif
memset(&pwm_params, 0, sizeof(pwm_params));
#ifdef SONAR
const sonarHardware_t *sonarHardware = NULL;
if (feature(FEATURE_SONAR)) {
sonarHardware = sonarGetHardwareConfiguration(&masterConfig.batteryConfig);
sonarGPIOConfig_t sonarGPIOConfig = {
.gpio = SONAR_GPIO,
.triggerPin = sonarHardware->echo_pin,
.echoPin = sonarHardware->trigger_pin,
};
pwm_params.sonarGPIOConfig = &sonarGPIOConfig;
}
#endif
// when using airplane/wing mixer, servo/motor outputs are remapped
if (masterConfig.mixerMode == MIXER_AIRPLANE || masterConfig.mixerMode == MIXER_FLYING_WING || masterConfig.mixerMode == MIXER_CUSTOM_AIRPLANE)
pwm_params.airplane = true;
else
pwm_params.airplane = false;
#if defined(USE_UART2) && defined(STM32F10X)
pwm_params.useUART2 = doesConfigurationUsePort(SERIAL_PORT_UART2);
#endif
#if defined(USE_UART3)
pwm_params.useUART3 = doesConfigurationUsePort(SERIAL_PORT_UART3);
#endif
#if defined(USE_UART4)
pwm_params.useUART4 = doesConfigurationUsePort(SERIAL_PORT_UART4);
#endif
#if defined(USE_UART5)
pwm_params.useUART5 = doesConfigurationUsePort(SERIAL_PORT_UART5);
#endif
pwm_params.useVbat = feature(FEATURE_VBAT);
pwm_params.useSoftSerial = feature(FEATURE_SOFTSERIAL);
pwm_params.useParallelPWM = feature(FEATURE_RX_PARALLEL_PWM);
pwm_params.useRSSIADC = feature(FEATURE_RSSI_ADC);
pwm_params.useCurrentMeterADC = feature(FEATURE_CURRENT_METER)
&& masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC;
pwm_params.useLEDStrip = feature(FEATURE_LED_STRIP);
pwm_params.usePPM = feature(FEATURE_RX_PPM);
pwm_params.useSerialRx = feature(FEATURE_RX_SERIAL);
#ifdef SONAR
pwm_params.useSonar = feature(FEATURE_SONAR);
#endif
#ifdef USE_SERVOS
pwm_params.useServos = isMixerUsingServos();
pwm_params.useChannelForwarding = feature(FEATURE_CHANNEL_FORWARDING);
pwm_params.servoCenterPulse = masterConfig.escAndServoConfig.servoCenterPulse;
pwm_params.servoPwmRate = masterConfig.servo_pwm_rate;
#endif
pwm_params.useOneshot = feature(FEATURE_ONESHOT125);
pwm_params.motorPwmRate = masterConfig.motor_pwm_rate;
pwm_params.idlePulse = masterConfig.escAndServoConfig.mincommand;
if (feature(FEATURE_3D))
pwm_params.idlePulse = masterConfig.flight3DConfig.neutral3d;
if (pwm_params.motorPwmRate > 500)
pwm_params.idlePulse = 0; // brushed motors
pwmRxInit(masterConfig.inputFilteringMode);
// pwmInit() needs to be called as soon as possible for ESC compatibility reasons
pwmIOConfiguration_t *pwmIOConfiguration = pwmInit(&pwm_params);
mixerUsePWMIOConfiguration(pwmIOConfiguration);
debug[2] = pwmIOConfiguration->pwmInputCount;
debug[3] = pwmIOConfiguration->ppmInputCount;
if (!feature(FEATURE_ONESHOT125))
motorControlEnable = true;
systemState |= SYSTEM_STATE_MOTORS_READY;
#ifdef INVERTER
initInverter();
#endif
#ifdef USE_SPI
spiInit(SPI1);
spiInit(SPI2);
#endif
#ifdef USE_HARDWARE_REVISION_DETECTION
updateHardwareRevision();
#endif
#if defined(NAZE)
if (hardwareRevision == NAZE32_SP) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
} else {
serialRemovePort(SERIAL_PORT_UART3);
}
#endif
#if defined(SPRACINGF3) && defined(SONAR) && defined(USE_SOFTSERIAL2)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
}
#endif
#if defined(SPRACINGF3MINI) && defined(SONAR) && defined(USE_SOFTSERIAL1)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL1);
}
#endif
#ifdef USE_I2C
#if defined(NAZE)
if (hardwareRevision != NAZE32_SP) {
i2cInit(I2C_DEVICE);
} else {
if (!doesConfigurationUsePort(SERIAL_PORT_UART3)) {
i2cInit(I2C_DEVICE);
}
}
#elif defined(CC3D)
if (!doesConfigurationUsePort(SERIAL_PORT_UART3)) {
i2cInit(I2C_DEVICE);
}
#else
i2cInit(I2C_DEVICE);
#endif
#endif
#ifdef USE_ADC
drv_adc_config_t adc_params;
adc_params.enableVBat = feature(FEATURE_VBAT);
adc_params.enableRSSI = feature(FEATURE_RSSI_ADC);
adc_params.enableCurrentMeter = feature(FEATURE_CURRENT_METER);
adc_params.enableExternal1 = false;
#ifdef OLIMEXINO
adc_params.enableExternal1 = true;
#endif
#ifdef NAZE
// optional ADC5 input on rev.5 hardware
adc_params.enableExternal1 = (hardwareRevision >= NAZE32_REV5);
#endif
adcInit(&adc_params);
#endif
initBoardAlignment(&masterConfig.boardAlignment);
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
displayInit(&masterConfig.rxConfig);
}
#endif
if (!sensorsAutodetect(&masterConfig.sensorAlignmentConfig, masterConfig.gyro_lpf,
masterConfig.acc_hardware, masterConfig.mag_hardware, masterConfig.baro_hardware, currentProfile->mag_declination,
masterConfig.looptime, masterConfig.gyroSync, masterConfig.gyroSyncDenominator)) {
// if gyro was not detected due to whatever reason, we give up now.
failureMode(FAILURE_MISSING_ACC);
}
systemState |= SYSTEM_STATE_SENSORS_READY;
flashLedsAndBeep();
#ifdef USE_SERVOS
mixerInitialiseServoFiltering(targetLooptime);
#endif
#ifdef MAG
if (sensors(SENSOR_MAG))
compassInit();
#endif
imuInit();
mspInit(&masterConfig.serialConfig);
#ifdef USE_CLI
cliInit(&masterConfig.serialConfig);
#endif
failsafeInit(&masterConfig.rxConfig, masterConfig.flight3DConfig.deadband3d_throttle);
rxInit(&masterConfig.rxConfig, currentProfile->modeActivationConditions);
#ifdef GPS
if (feature(FEATURE_GPS)) {
gpsInit(
&masterConfig.serialConfig,
&masterConfig.gpsConfig
);
navigationInit(
¤tProfile->gpsProfile,
¤tProfile->pidProfile
);
}
#endif
#ifdef SONAR
if (feature(FEATURE_SONAR)) {
sonarInit(sonarHardware);
}
#endif
#ifdef LED_STRIP
ledStripInit(masterConfig.ledConfigs, masterConfig.colors);
if (feature(FEATURE_LED_STRIP)) {
ledStripEnable();
}
#endif
#ifdef TELEMETRY
if (feature(FEATURE_TELEMETRY)) {
telemetryInit();
}
#endif
#ifdef USB_CABLE_DETECTION
usbCableDetectInit();
#endif
#ifdef TRANSPONDER
if (feature(FEATURE_TRANSPONDER)) {
transponderInit(masterConfig.transponderData);
transponderEnable();
transponderStartRepeating();
systemState |= SYSTEM_STATE_TRANSPONDER_ENABLED;
}
#endif
#ifdef USE_FLASHFS
#ifdef NAZE
if (hardwareRevision == NAZE32_REV5) {
m25p16_init();
}
#elif defined(USE_FLASH_M25P16)
m25p16_init();
#endif
flashfsInit();
#endif
#ifdef USE_SDCARD
bool sdcardUseDMA = false;
sdcardInsertionDetectInit();
#ifdef SDCARD_DMA_CHANNEL_TX
#if defined(LED_STRIP) && defined(WS2811_DMA_CHANNEL)
// Ensure the SPI Tx DMA doesn't overlap with the led strip
sdcardUseDMA = !feature(FEATURE_LED_STRIP) || SDCARD_DMA_CHANNEL_TX != WS2811_DMA_CHANNEL;
#else
sdcardUseDMA = true;
#endif
#endif
sdcard_init(sdcardUseDMA);
afatfs_init();
#endif
#ifdef BLACKBOX
initBlackbox();
#endif
if (masterConfig.mixerMode == MIXER_GIMBAL) {
accSetCalibrationCycles(CALIBRATING_ACC_CYCLES);
}
gyroSetCalibrationCycles(CALIBRATING_GYRO_CYCLES);
#ifdef BARO
baroSetCalibrationCycles(CALIBRATING_BARO_CYCLES);
#endif
// start all timers
// TODO - not implemented yet
timerStart();
ENABLE_STATE(SMALL_ANGLE);
DISABLE_ARMING_FLAG(PREVENT_ARMING);
#ifdef SOFTSERIAL_LOOPBACK
// FIXME this is a hack, perhaps add a FUNCTION_LOOPBACK to support it properly
loopbackPort = (serialPort_t*)&(softSerialPorts[0]);
if (!loopbackPort->vTable) {
loopbackPort = openSoftSerial(0, NULL, 19200, SERIAL_NOT_INVERTED);
}
serialPrint(loopbackPort, "LOOPBACK\r\n");
#endif
// Now that everything has powered up the voltage and cell count be determined.
if (feature(FEATURE_VBAT | FEATURE_CURRENT_METER))
batteryInit(&masterConfig.batteryConfig);
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
#ifdef USE_OLED_GPS_DEBUG_PAGE_ONLY
displayShowFixedPage(PAGE_GPS);
#else
displayResetPageCycling();
displayEnablePageCycling();
#endif
}
#endif
#ifdef CJMCU
LED2_ON;
#endif
// Latch active features AGAIN since some may be modified by init().
latchActiveFeatures();
motorControlEnable = true;
systemState |= SYSTEM_STATE_READY;
}
#ifdef SOFTSERIAL_LOOPBACK
void processLoopback(void) {
if (loopbackPort) {
uint8_t bytesWaiting;
while ((bytesWaiting = serialRxBytesWaiting(loopbackPort))) {
uint8_t b = serialRead(loopbackPort);
serialWrite(loopbackPort, b);
};
}
}
#else
#define processLoopback()
#endif
int main(void) {
init();
/* Setup scheduler */
if (masterConfig.gyroSync) {
rescheduleTask(TASK_GYROPID, targetLooptime - INTERRUPT_WAIT_TIME);
}
else {
rescheduleTask(TASK_GYROPID, targetLooptime);
}
setTaskEnabled(TASK_GYROPID, true);
setTaskEnabled(TASK_ACCEL, sensors(SENSOR_ACC));
setTaskEnabled(TASK_SERIAL, true);
#ifdef BEEPER
setTaskEnabled(TASK_BEEPER, true);
#endif
setTaskEnabled(TASK_BATTERY, feature(FEATURE_VBAT) || feature(FEATURE_CURRENT_METER));
setTaskEnabled(TASK_RX, true);
#ifdef GPS
setTaskEnabled(TASK_GPS, feature(FEATURE_GPS));
#endif
#ifdef MAG
setTaskEnabled(TASK_COMPASS, sensors(SENSOR_MAG));
#endif
#ifdef BARO
setTaskEnabled(TASK_BARO, sensors(SENSOR_BARO));
#endif
#ifdef SONAR
setTaskEnabled(TASK_SONAR, sensors(SENSOR_SONAR));
#endif
#if defined(BARO) || defined(SONAR)
setTaskEnabled(TASK_ALTITUDE, sensors(SENSOR_BARO) || sensors(SENSOR_SONAR));
#endif
#ifdef DISPLAY
setTaskEnabled(TASK_DISPLAY, feature(FEATURE_DISPLAY));
#endif
#ifdef TELEMETRY
setTaskEnabled(TASK_TELEMETRY, feature(FEATURE_TELEMETRY));
#endif
#ifdef LED_STRIP
setTaskEnabled(TASK_LEDSTRIP, feature(FEATURE_LED_STRIP));
#endif
#ifdef TRANSPONDER
setTaskEnabled(TASK_TRANSPONDER, feature(FEATURE_TRANSPONDER));
#endif
while (1) {
scheduler();
processLoopback();
}
}
void HardFault_Handler(void)
{
// fall out of the sky
uint8_t requiredStateForMotors = SYSTEM_STATE_CONFIG_LOADED | SYSTEM_STATE_MOTORS_READY;
if ((systemState & requiredStateForMotors) == requiredStateForMotors) {
stopMotors();
}
#ifdef TRANSPONDER
// prevent IR LEDs from burning out.
uint8_t requiredStateForTransponder = SYSTEM_STATE_CONFIG_LOADED | SYSTEM_STATE_TRANSPONDER_ENABLED;
if ((systemState & requiredStateForTransponder) == requiredStateForTransponder) {
transponderIrDisable();
}
#endif
while (1);
}
int main(void) {
// TODO disable JTAG
// Stack limit should be less than real stack size, so we have a chance
// to recover from limit hit. (Limit is measured in bytes.)
mp_stack_set_limit((char*)&_ram_end - (char*)&_heap_end - 1024);
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Global MSP (MCU Support Package) initialization
*/
HAL_Init();
// set the system clock to be HSE
SystemClock_Config();
// enable GPIO clocks
__GPIOA_CLK_ENABLE();
__GPIOB_CLK_ENABLE();
__GPIOC_CLK_ENABLE();
__GPIOD_CLK_ENABLE();
// enable the CCM RAM
__CCMDATARAMEN_CLK_ENABLE();
#if 0
#if defined(NETDUINO_PLUS_2)
{
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_25MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
#if MICROPY_HW_HAS_SDCARD
// Turn on the power enable for the sdcard (PB1)
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_WriteBit(GPIOB, GPIO_Pin_1, Bit_SET);
#endif
// Turn on the power for the 5V on the expansion header (PB2)
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_WriteBit(GPIOB, GPIO_Pin_2, Bit_SET);
}
#endif
#endif
// basic sub-system init
pendsv_init();
timer_tim3_init();
led_init();
#if MICROPY_HW_HAS_SWITCH
switch_init0();
#endif
int first_soft_reset = true;
soft_reset:
// check if user switch held to select the reset mode
led_state(1, 0);
led_state(2, 1);
led_state(3, 0);
led_state(4, 0);
uint reset_mode = 1;
#if MICROPY_HW_HAS_SWITCH
if (switch_get()) {
for (uint i = 0; i < 3000; i++) {
if (!switch_get()) {
break;
}
HAL_Delay(20);
if (i % 30 == 29) {
if (++reset_mode > 3) {
reset_mode = 1;
}
led_state(2, reset_mode & 1);
led_state(3, reset_mode & 2);
led_state(4, reset_mode & 4);
}
}
// flash the selected reset mode
for (uint i = 0; i < 6; i++) {
led_state(2, 0);
led_state(3, 0);
led_state(4, 0);
HAL_Delay(50);
led_state(2, reset_mode & 1);
led_state(3, reset_mode & 2);
led_state(4, reset_mode & 4);
HAL_Delay(50);
}
HAL_Delay(400);
}
#endif
#if MICROPY_HW_ENABLE_RTC
if (first_soft_reset) {
rtc_init();
}
#endif
// more sub-system init
#if MICROPY_HW_HAS_SDCARD
if (first_soft_reset) {
sdcard_init();
}
#endif
if (first_soft_reset) {
storage_init();
}
// GC init
gc_init(&_heap_start, &_heap_end);
// Micro Python init
mp_init();
mp_obj_list_init(mp_sys_path, 0);
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR_)); // current dir (or base dir of the script)
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR__slash_flash));
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR__slash_flash_slash_lib));
mp_obj_list_init(mp_sys_argv, 0);
// Change #if 0 to #if 1 if you want REPL on UART_6 (or another uart)
// as well as on USB VCP
#if 0
{
mp_obj_t args[2] = {
MP_OBJ_NEW_SMALL_INT(PYB_UART_6),
MP_OBJ_NEW_SMALL_INT(115200),
};
pyb_stdio_uart = pyb_uart_type.make_new((mp_obj_t)&pyb_uart_type, MP_ARRAY_SIZE(args), 0, args);
}
#else
pyb_stdio_uart = NULL;
#endif
// Initialise low-level sub-systems. Here we need to very basic things like
// zeroing out memory and resetting any of the sub-systems. Following this
// we can run Python scripts (eg boot.py), but anything that is configurable
// by boot.py must be set after boot.py is run.
readline_init0();
pin_init0();
extint_init0();
timer_init0();
uart_init0();
#if MICROPY_HW_ENABLE_RNG
rng_init0();
#endif
i2c_init0();
spi_init0();
pyb_usb_init0();
// Initialise the local flash filesystem.
// Create it if needed, and mount in on /flash.
{
// try to mount the flash
FRESULT res = f_mount(&fatfs0, "/flash", 1);
if (reset_mode == 3 || res == FR_NO_FILESYSTEM) {
// no filesystem, or asked to reset it, so create a fresh one
// LED on to indicate creation of LFS
led_state(PYB_LED_R2, 1);
uint32_t start_tick = HAL_GetTick();
res = f_mkfs("/flash", 0, 0);
if (res == FR_OK) {
// success creating fresh LFS
} else {
__fatal_error("could not create LFS");
}
// set label
f_setlabel("/flash/pybflash");
// create empty main.py
FIL fp;
f_open(&fp, "/flash/main.py", FA_WRITE | FA_CREATE_ALWAYS);
UINT n;
f_write(&fp, fresh_main_py, sizeof(fresh_main_py) - 1 /* don't count null terminator */, &n);
// TODO check we could write n bytes
f_close(&fp);
// create .inf driver file
f_open(&fp, "/flash/pybcdc.inf", FA_WRITE | FA_CREATE_ALWAYS);
f_write(&fp, fresh_pybcdc_inf, sizeof(fresh_pybcdc_inf) - 1 /* don't count null terminator */, &n);
f_close(&fp);
// create readme file
f_open(&fp, "/flash/README.txt", FA_WRITE | FA_CREATE_ALWAYS);
f_write(&fp, fresh_readme_txt, sizeof(fresh_readme_txt) - 1 /* don't count null terminator */, &n);
f_close(&fp);
// keep LED on for at least 200ms
sys_tick_wait_at_least(start_tick, 200);
led_state(PYB_LED_R2, 0);
} else if (res == FR_OK) {
// mount sucessful
} else {
__fatal_error("could not access LFS");
}
}
// The current directory is used as the boot up directory.
// It is set to the internal flash filesystem by default.
f_chdrive("/flash");
// Make sure we have a /flash/boot.py. Create it if needed.
{
FILINFO fno;
#if _USE_LFN
fno.lfname = NULL;
fno.lfsize = 0;
#endif
FRESULT res = f_stat("/flash/boot.py", &fno);
if (res == FR_OK) {
if (fno.fattrib & AM_DIR) {
// exists as a directory
// TODO handle this case
// see http://elm-chan.org/fsw/ff/img/app2.c for a "rm -rf" implementation
} else {
// exists as a file, good!
}
} else {
// doesn't exist, create fresh file
// LED on to indicate creation of boot.py
led_state(PYB_LED_R2, 1);
uint32_t start_tick = HAL_GetTick();
FIL fp;
f_open(&fp, "/flash/boot.py", FA_WRITE | FA_CREATE_ALWAYS);
UINT n;
f_write(&fp, fresh_boot_py, sizeof(fresh_boot_py) - 1 /* don't count null terminator */, &n);
// TODO check we could write n bytes
f_close(&fp);
// keep LED on for at least 200ms
sys_tick_wait_at_least(start_tick, 200);
led_state(PYB_LED_R2, 0);
}
}
#if defined(USE_DEVICE_MODE)
usb_storage_medium_t usb_medium = USB_STORAGE_MEDIUM_FLASH;
#endif
#if MICROPY_HW_HAS_SDCARD
// if an SD card is present then mount it on /sd/
if (sdcard_is_present()) {
FRESULT res = f_mount(&fatfs1, "/sd", 1);
if (res != FR_OK) {
printf("[SD] could not mount SD card\n");
} else {
// use SD card as current directory
f_chdrive("/sd");
// TODO these should go before the /flash entries in the path
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR__slash_sd));
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR__slash_sd_slash_lib));
if (first_soft_reset) {
// use SD card as medium for the USB MSD
#if defined(USE_DEVICE_MODE)
usb_medium = USB_STORAGE_MEDIUM_SDCARD;
#endif
}
}
}
#endif
// reset config variables; they should be set by boot.py
pyb_config_main = MP_OBJ_NULL;
pyb_config_usb_mode = MP_OBJ_NULL;
// run boot.py, if it exists
// TODO perhaps have pyb.reboot([bootpy]) function to soft-reboot and execute custom boot.py
if (reset_mode == 1) {
const char *boot_py = "boot.py";
FRESULT res = f_stat(boot_py, NULL);
if (res == FR_OK) {
int ret = pyexec_file(boot_py);
if (ret & PYEXEC_FORCED_EXIT) {
goto soft_reset_exit;
}
if (!ret) {
flash_error(4);
}
}
}
// turn boot-up LEDs off
led_state(2, 0);
led_state(3, 0);
led_state(4, 0);
// Now we initialise sub-systems that need configuration from boot.py,
// or whose initialisation can be safely deferred until after running
// boot.py.
#if defined(USE_HOST_MODE)
// USB host
pyb_usb_host_init();
#elif defined(USE_DEVICE_MODE)
// USB device
usb_device_mode_t usb_mode = USB_DEVICE_MODE_CDC_MSC;
// if we are not in reset_mode==1, this config variable will always be NULL
if (pyb_config_usb_mode != MP_OBJ_NULL) {
if (strcmp(mp_obj_str_get_str(pyb_config_usb_mode), "CDC+HID") == 0) {
usb_mode = USB_DEVICE_MODE_CDC_HID;
}
}
pyb_usb_dev_init(usb_mode, usb_medium);
#endif
#if MICROPY_HW_HAS_MMA7660
// MMA accel: init and reset
accel_init();
#endif
#if MICROPY_HW_ENABLE_SERVO
// servo
servo_init();
#endif
#if MICROPY_HW_ENABLE_DAC
// DAC
dac_init();
#endif
mod_network_init();
// At this point everything is fully configured and initialised.
// Run the main script from the current directory.
if (reset_mode == 1 && pyexec_mode_kind == PYEXEC_MODE_FRIENDLY_REPL) {
const char *main_py;
if (pyb_config_main == MP_OBJ_NULL) {
main_py = "main.py";
} else {
main_py = mp_obj_str_get_str(pyb_config_main);
}
FRESULT res = f_stat(main_py, NULL);
if (res == FR_OK) {
int ret = pyexec_file(main_py);
if (ret & PYEXEC_FORCED_EXIT) {
goto soft_reset_exit;
}
if (!ret) {
flash_error(3);
}
}
}
// Main script is finished, so now go into REPL mode.
// The REPL mode can change, or it can request a soft reset.
for (;;) {
if (pyexec_mode_kind == PYEXEC_MODE_RAW_REPL) {
if (pyexec_raw_repl() != 0) {
break;
}
} else {
if (pyexec_friendly_repl() != 0) {
break;
}
}
}
soft_reset_exit:
// soft reset
printf("PYB: sync filesystems\n");
storage_flush();
printf("PYB: soft reboot\n");
timer_deinit();
uart_deinit();
first_soft_reset = false;
goto soft_reset;
}
int main(void) {
// TODO disable JTAG
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Global MSP (MCU Support Package) initialization
*/
HAL_Init();
// set the system clock to be HSE
SystemClock_Config();
// enable GPIO clocks
__GPIOA_CLK_ENABLE();
__GPIOB_CLK_ENABLE();
__GPIOC_CLK_ENABLE();
__GPIOD_CLK_ENABLE();
// enable the CCM RAM
__CCMDATARAMEN_CLK_ENABLE();
#if 0
#if defined(NETDUINO_PLUS_2)
{
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_25MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
#if MICROPY_HW_HAS_SDCARD
// Turn on the power enable for the sdcard (PB1)
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_WriteBit(GPIOB, GPIO_Pin_1, Bit_SET);
#endif
// Turn on the power for the 5V on the expansion header (PB2)
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_WriteBit(GPIOB, GPIO_Pin_2, Bit_SET);
}
#endif
#endif
// basic sub-system init
pendsv_init();
timer_tim3_init();
led_init();
switch_init0();
int first_soft_reset = true;
soft_reset:
// check if user switch held to select the reset mode
led_state(1, 0);
led_state(2, 1);
led_state(3, 0);
led_state(4, 0);
uint reset_mode = 1;
#if MICROPY_HW_HAS_SWITCH
if (switch_get()) {
for (uint i = 0; i < 3000; i++) {
if (!switch_get()) {
break;
}
HAL_Delay(20);
if (i % 30 == 29) {
if (++reset_mode > 3) {
reset_mode = 1;
}
led_state(2, reset_mode & 1);
led_state(3, reset_mode & 2);
led_state(4, reset_mode & 4);
}
}
// flash the selected reset mode
for (uint i = 0; i < 6; i++) {
led_state(2, 0);
led_state(3, 0);
led_state(4, 0);
HAL_Delay(50);
led_state(2, reset_mode & 1);
led_state(3, reset_mode & 2);
led_state(4, reset_mode & 4);
HAL_Delay(50);
}
HAL_Delay(400);
}
#endif
#if MICROPY_HW_ENABLE_RTC
if (first_soft_reset) {
rtc_init();
}
#endif
// more sub-system init
#if MICROPY_HW_HAS_SDCARD
if (first_soft_reset) {
sdcard_init();
}
#endif
if (first_soft_reset) {
storage_init();
}
// GC init
gc_init(&_heap_start, &_heap_end);
// Change #if 0 to #if 1 if you want REPL on USART_6 (or another usart)
// as well as on USB VCP
#if 0
pyb_usart_global_debug = pyb_Usart(MP_OBJ_NEW_SMALL_INT(PYB_USART_YA),
MP_OBJ_NEW_SMALL_INT(115200));
#else
pyb_usart_global_debug = NULL;
#endif
// Micro Python init
qstr_init();
mp_init();
mp_obj_list_init(mp_sys_path, 0);
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR_0_colon__slash_));
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR_0_colon__slash_lib));
mp_obj_list_init(mp_sys_argv, 0);
readline_init();
exti_init();
#if MICROPY_HW_HAS_SWITCH
// must come after exti_init
switch_init();
#endif
#if MICROPY_HW_HAS_LCD
// LCD init (just creates class, init hardware by calling LCD())
lcd_init();
#endif
pin_map_init();
// local filesystem init
{
// try to mount the flash
FRESULT res = f_mount(&fatfs0, "0:", 1);
if (reset_mode == 3 || res == FR_NO_FILESYSTEM) {
// no filesystem, or asked to reset it, so create a fresh one
// LED on to indicate creation of LFS
led_state(PYB_LED_R2, 1);
uint32_t start_tick = HAL_GetTick();
res = f_mkfs("0:", 0, 0);
if (res == FR_OK) {
// success creating fresh LFS
} else {
__fatal_error("could not create LFS");
}
// create empty main.py
FIL fp;
f_open(&fp, "0:/main.py", FA_WRITE | FA_CREATE_ALWAYS);
UINT n;
f_write(&fp, fresh_main_py, sizeof(fresh_main_py) - 1 /* don't count null terminator */, &n);
// TODO check we could write n bytes
f_close(&fp);
// create .inf driver file
f_open(&fp, "0:/pybcdc.inf", FA_WRITE | FA_CREATE_ALWAYS);
f_write(&fp, fresh_pybcdc_inf, sizeof(fresh_pybcdc_inf) - 1 /* don't count null terminator */, &n);
f_close(&fp);
// keep LED on for at least 200ms
sys_tick_wait_at_least(start_tick, 200);
led_state(PYB_LED_R2, 0);
} else if (res == FR_OK) {
// mount sucessful
} else {
__fatal_error("could not access LFS");
}
}
// make sure we have a 0:/boot.py
{
FILINFO fno;
#if _USE_LFN
fno.lfname = NULL;
fno.lfsize = 0;
#endif
FRESULT res = f_stat("0:/boot.py", &fno);
if (res == FR_OK) {
if (fno.fattrib & AM_DIR) {
// exists as a directory
// TODO handle this case
// see http://elm-chan.org/fsw/ff/img/app2.c for a "rm -rf" implementation
} else {
// exists as a file, good!
}
} else {
// doesn't exist, create fresh file
// LED on to indicate creation of boot.py
led_state(PYB_LED_R2, 1);
uint32_t start_tick = HAL_GetTick();
FIL fp;
f_open(&fp, "0:/boot.py", FA_WRITE | FA_CREATE_ALWAYS);
UINT n;
f_write(&fp, fresh_boot_py, sizeof(fresh_boot_py) - 1 /* don't count null terminator */, &n);
// TODO check we could write n bytes
f_close(&fp);
// keep LED on for at least 200ms
sys_tick_wait_at_least(start_tick, 200);
led_state(PYB_LED_R2, 0);
}
}
// root device defaults to internal flash filesystem
uint root_device = 0;
#if defined(USE_DEVICE_MODE)
usb_storage_medium_t usb_medium = USB_STORAGE_MEDIUM_FLASH;
#endif
#if MICROPY_HW_HAS_SDCARD
// if an SD card is present then mount it on 1:/
if (reset_mode == 1 && sdcard_is_present()) {
FRESULT res = f_mount(&fatfs1, "1:", 1);
if (res != FR_OK) {
printf("[SD] could not mount SD card\n");
} else {
// use SD card as root device
root_device = 1;
if (first_soft_reset) {
// use SD card as medium for the USB MSD
#if defined(USE_DEVICE_MODE)
usb_medium = USB_STORAGE_MEDIUM_SDCARD;
#endif
}
}
}
#else
// Get rid of compiler warning if no SDCARD is configured.
(void)first_soft_reset;
#endif
// run <root>:/boot.py, if it exists
if (reset_mode == 1) {
const char *boot_file;
if (root_device == 0) {
boot_file = "0:/boot.py";
} else {
boot_file = "1:/boot.py";
}
FRESULT res = f_stat(boot_file, NULL);
if (res == FR_OK) {
if (!pyexec_file(boot_file)) {
flash_error(4);
}
}
}
// turn boot-up LEDs off
led_state(2, 0);
led_state(3, 0);
led_state(4, 0);
#if defined(USE_HOST_MODE)
// USB host
pyb_usb_host_init();
#elif defined(USE_DEVICE_MODE)
// USB device
if (reset_mode == 1) {
usb_device_mode_t usb_mode = USB_DEVICE_MODE_CDC_MSC;
if (pyb_config_usb_mode != MP_OBJ_NULL) {
if (strcmp(mp_obj_str_get_str(pyb_config_usb_mode), "CDC+HID") == 0) {
usb_mode = USB_DEVICE_MODE_CDC_HID;
}
}
pyb_usb_dev_init(usb_mode, usb_medium);
} else {
pyb_usb_dev_init(USB_DEVICE_MODE_CDC_MSC, usb_medium);
}
#endif
#if MICROPY_HW_ENABLE_RNG
// RNG
rng_init();
#endif
#if MICROPY_HW_ENABLE_TIMER
// timer
//timer_init();
#endif
// I2C
i2c_init();
#if MICROPY_HW_HAS_MMA7660
// MMA accel: init and reset
accel_init();
#endif
#if MICROPY_HW_ENABLE_SERVO
// servo
servo_init();
#endif
#if MICROPY_HW_ENABLE_DAC
// DAC
dac_init();
#endif
// now that everything is initialised, run main script
if (reset_mode == 1 && pyexec_mode_kind == PYEXEC_MODE_FRIENDLY_REPL) {
vstr_t *vstr = vstr_new();
vstr_printf(vstr, "%d:/", root_device);
if (pyb_config_main == MP_OBJ_NULL) {
vstr_add_str(vstr, "main.py");
} else {
vstr_add_str(vstr, mp_obj_str_get_str(pyb_config_main));
}
FRESULT res = f_stat(vstr_str(vstr), NULL);
if (res == FR_OK) {
if (!pyexec_file(vstr_str(vstr))) {
flash_error(3);
}
}
vstr_free(vstr);
}
#if 0
#if MICROPY_HW_HAS_WLAN
// wifi
pyb_wlan_init();
pyb_wlan_start();
#endif
#endif
// enter REPL
// REPL mode can change, or it can request a soft reset
for (;;) {
if (pyexec_mode_kind == PYEXEC_MODE_RAW_REPL) {
if (pyexec_raw_repl() != 0) {
break;
}
} else {
if (pyexec_friendly_repl() != 0) {
break;
}
}
}
printf("PYB: sync filesystems\n");
storage_flush();
printf("PYB: soft reboot\n");
first_soft_reset = false;
goto soft_reset;
}
int main(void) {
cli();
/* We need to use a timer to control how long our main loop iterations are.
* Experiments showed that the main loop was executing approximately every
* 3.2 milliseconds, which is too quick for the sdcard to write a block
* of data. Here we are configuring Timer1 because it is a "16-bit" timer
* which would allow us to count to values greater than (2^8)-1. For a pre-
* scale value of 64, the timer will count up to 16,000,000/64 = 250,000.
* This gives us a timer period of 250,000 ticks/sec = 4 microseconds/tick.
* Suppose we want the main loop to run 40 times per second (40 Hz), we would
* need to restart the loop when Timer1 reaches the value: 250,000/40 = 6250
* See Atmel datasheet for Mega, Section 17.11
*/
TCCR1A = 0b00000000; // Normal operation; no waveform generation by default
TCCR1B = 0b00000011; // No input capture, waveform gen; prescaler = 64
TCCR1C = 0b00000000; // No output compare
TIMSK1 = 0b00000000;
// TIMING DEBUG - Digital Pin 4
DDRG |= (1 << 5);
char msg[64];
if (button_init() &&
uwrite_init() &&
cmps10_init() &&
sdcard_init()) {
uwrite_print_buff("All systems go!\r\n");
return 0;
} else {
uwrite_print_buff("There was an error during init\r\n");
return 1;
}
memset(msg, 0, sizeof(msg));
memset(&statevars, 0, sizeof(statevars));
statevars.prefix = 0xDADAFEED;
statevars.suffix = 0xCAFEBABE;
uint32_t iterations = 0;
sei();
TIMSK1 = 0b00000001;
while (1) {
// TIMING DEBUG FOR OSCILLOSCOPE
PORTG |= (1 << 5);
TCNT1 = 0;
button_update();
cmps10_update_all();
statevars.main_loop_counter = iterations;
mainloop_timer_overflow = 0;
// TIMING DEBUG FOR OSCILLOSCOPE
PORTG &= (0 << 5);
if (button_is_pressed()) {
uwrite_print_buff("The button is pressed! The LED should be on.\r\n");
led_turn_on();
statevars.mission_started = 1;
} else {
led_turn_off();
statevars.mission_started = 0;
}
snprintf(msg, sizeof(msg),
"Heading: %u Pitch: %d Roll: %hhd\r\n",
cmps10_heading, cmps10_pitch, cmps10_roll);
// Needed to cast these values to display negative pitch and roll values
//(int8_t) statevars.heading_raw, (int8_t) statevars.pitch_deg, (int8_t) statevars.roll_deg);
uwrite_print_buff(msg);
sdcard_write_data();
iterations++;
if (iterations > 256) {
uwrite_print_buff("Finished collecting data!\r\n");
break;
}
/* Ensure that the main loop period is as long as we want it to be.
* This means (1) triggering the main loop to restart we notice it is
* running too long, and (2) performing busy waiting if the instructions
* above finish before the desired loop duration.
*/
while (1) {
if (mainloop_timer_overflow) {
break;
}
if (TCNT1 >= MAINLOOP_PERIOD_TICKS) {
break;
}
}
}
return 0;
}
void init(void)
{
printfSupportInit();
initEEPROM();
ensureEEPROMContainsValidData();
readEEPROM();
systemState |= SYSTEM_STATE_CONFIG_LOADED;
// initialize IO (needed for all IO operations)
IOInitGlobal();
#ifdef STM32F303
// start fpu
SCB->CPACR = (0x3 << (10*2)) | (0x3 << (11*2));
#endif
#ifdef STM32F303xC
SetSysClock();
#endif
#ifdef STM32F10X
// Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers
// Configure the Flash Latency cycles and enable prefetch buffer
SetSysClock(masterConfig.emf_avoidance);
#endif
i2cSetOverclock(masterConfig.i2c_overclock);
#ifdef USE_HARDWARE_REVISION_DETECTION
detectHardwareRevision();
#endif
systemInit();
// Latch active features to be used for feature() in the remainder of init().
latchActiveFeatures();
#ifdef ALIENFLIGHTF3
ledInit(hardwareRevision == AFF3_REV_1 ? false : true);
#else
ledInit(false);
#endif
#ifdef SPEKTRUM_BIND
if (feature(FEATURE_RX_SERIAL)) {
switch (masterConfig.rxConfig.serialrx_provider) {
case SERIALRX_SPEKTRUM1024:
case SERIALRX_SPEKTRUM2048:
// Spektrum satellite binding if enabled on startup.
// Must be called before that 100ms sleep so that we don't lose satellite's binding window after startup.
// The rest of Spektrum initialization will happen later - via spektrumInit()
spektrumBind(&masterConfig.rxConfig);
break;
}
}
#endif
delay(500);
timerInit(); // timer must be initialized before any channel is allocated
serialInit(&masterConfig.serialConfig, feature(FEATURE_SOFTSERIAL));
#ifdef USE_SERVOS
mixerInit(masterConfig.mixerMode, masterConfig.customMotorMixer, masterConfig.customServoMixer);
#else
mixerInit(masterConfig.mixerMode, masterConfig.customMotorMixer);
#endif
drv_pwm_config_t pwm_params;
memset(&pwm_params, 0, sizeof(pwm_params));
#ifdef SONAR
if (feature(FEATURE_SONAR)) {
const sonarHcsr04Hardware_t *sonarHardware = sonarGetHardwareConfiguration(masterConfig.batteryConfig.currentMeterType);
if (sonarHardware) {
pwm_params.useSonar = true;
pwm_params.sonarIOConfig.triggerTag = sonarHardware->triggerTag;
pwm_params.sonarIOConfig.echoTag = sonarHardware->echoTag;
}
}
#endif
// when using airplane/wing mixer, servo/motor outputs are remapped
if (masterConfig.mixerMode == MIXER_AIRPLANE || masterConfig.mixerMode == MIXER_FLYING_WING || masterConfig.mixerMode == MIXER_CUSTOM_AIRPLANE)
pwm_params.airplane = true;
else
pwm_params.airplane = false;
#if defined(USE_USART2) && defined(STM32F10X)
pwm_params.useUART2 = doesConfigurationUsePort(SERIAL_PORT_USART2);
#endif
#ifdef STM32F303xC
pwm_params.useUART3 = doesConfigurationUsePort(SERIAL_PORT_USART3);
#endif
pwm_params.useVbat = feature(FEATURE_VBAT);
pwm_params.useSoftSerial = feature(FEATURE_SOFTSERIAL);
pwm_params.useParallelPWM = feature(FEATURE_RX_PARALLEL_PWM);
pwm_params.useRSSIADC = feature(FEATURE_RSSI_ADC);
pwm_params.useCurrentMeterADC = feature(FEATURE_CURRENT_METER)
&& masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC;
pwm_params.useLEDStrip = feature(FEATURE_LED_STRIP);
pwm_params.usePPM = feature(FEATURE_RX_PPM);
pwm_params.useSerialRx = feature(FEATURE_RX_SERIAL);
#ifdef USE_SERVOS
pwm_params.useServos = isServoOutputEnabled();
pwm_params.useChannelForwarding = feature(FEATURE_CHANNEL_FORWARDING);
pwm_params.servoCenterPulse = masterConfig.escAndServoConfig.servoCenterPulse;
pwm_params.servoPwmRate = masterConfig.servo_pwm_rate;
#endif
pwm_params.useOneshot = feature(FEATURE_ONESHOT125);
pwm_params.motorPwmRate = masterConfig.motor_pwm_rate;
pwm_params.idlePulse = masterConfig.escAndServoConfig.mincommand;
if (feature(FEATURE_3D))
pwm_params.idlePulse = masterConfig.flight3DConfig.neutral3d;
if (pwm_params.motorPwmRate > 500)
pwm_params.idlePulse = 0; // brushed motors
#ifndef SKIP_RX_PWM_PPM
pwmRxInit(masterConfig.inputFilteringMode);
#endif
// pwmInit() needs to be called as soon as possible for ESC compatibility reasons
pwmInit(&pwm_params);
mixerUsePWMIOConfiguration();
if (!feature(FEATURE_ONESHOT125))
motorControlEnable = true;
systemState |= SYSTEM_STATE_MOTORS_READY;
#ifdef BEEPER
beeperConfig_t beeperConfig = {
.ioTag = IO_TAG(BEEPER),
#ifdef BEEPER_INVERTED
.isOD = false,
.isInverted = true
#else
.isOD = true,
.isInverted = false
#endif
};
#ifdef NAZE
if (hardwareRevision >= NAZE32_REV5) {
// naze rev4 and below used opendrain to PNP for buzzer. Rev5 and above use PP to NPN.
beeperConfig.isOD = false;
beeperConfig.isInverted = true;
}
#endif
beeperInit(&beeperConfig);
#endif
#ifdef INVERTER
initInverter();
#endif
#ifdef USE_SPI
spiInit(SPI1);
spiInit(SPI2);
#endif
#ifdef USE_HARDWARE_REVISION_DETECTION
updateHardwareRevision();
#endif
#if defined(NAZE)
if (hardwareRevision == NAZE32_SP) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
} else {
serialRemovePort(SERIAL_PORT_USART3);
}
#endif
#if defined(SPRACINGF3) && defined(SONAR) && defined(USE_SOFTSERIAL2)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
}
#endif
#if defined(FURYF3) && defined(SONAR) && defined(USE_SOFTSERIAL1)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL1);
}
#endif
#ifdef USE_I2C
#if defined(NAZE)
if (hardwareRevision != NAZE32_SP) {
i2cInit(I2C_DEVICE);
} else {
if (!doesConfigurationUsePort(SERIAL_PORT_USART3)) {
i2cInit(I2C_DEVICE);
}
}
#elif defined(CC3D)
if (!doesConfigurationUsePort(SERIAL_PORT_USART3)) {
i2cInit(I2C_DEVICE);
}
#else
i2cInit(I2C_DEVICE);
#endif
#endif
#ifdef USE_ADC
drv_adc_config_t adc_params;
adc_params.enableVBat = feature(FEATURE_VBAT);
adc_params.enableRSSI = feature(FEATURE_RSSI_ADC);
adc_params.enableCurrentMeter = feature(FEATURE_CURRENT_METER);
adc_params.enableExternal1 = false;
#ifdef OLIMEXINO
adc_params.enableExternal1 = true;
#endif
#ifdef NAZE
// optional ADC5 input on rev.5 hardware
adc_params.enableExternal1 = (hardwareRevision >= NAZE32_REV5);
#endif
adcInit(&adc_params);
#endif
initBoardAlignment(&masterConfig.boardAlignment);
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
displayInit(&masterConfig.rxConfig);
}
#endif
#ifdef GPS
if (feature(FEATURE_GPS)) {
gpsPreInit(&masterConfig.gpsConfig);
}
#endif
// Set gyro sampling rate divider before initialization
gyroSetSampleRate(masterConfig.looptime, masterConfig.gyro_lpf, masterConfig.gyroSync, masterConfig.gyroSyncDenominator);
if (!sensorsAutodetect(&masterConfig.sensorAlignmentConfig,
masterConfig.gyro_lpf,
masterConfig.acc_hardware,
masterConfig.mag_hardware,
masterConfig.baro_hardware,
currentProfile->mag_declination)) {
// if gyro was not detected due to whatever reason, we give up now.
failureMode(FAILURE_MISSING_ACC);
}
systemState |= SYSTEM_STATE_SENSORS_READY;
LED1_ON;
LED0_OFF;
for (int i = 0; i < 10; i++) {
LED1_TOGGLE;
LED0_TOGGLE;
delay(25);
BEEP_ON;
delay(25);
BEEP_OFF;
}
LED0_OFF;
LED1_OFF;
#ifdef MAG
if (sensors(SENSOR_MAG))
compassInit();
#endif
imuInit();
mspInit(&masterConfig.serialConfig);
#ifdef USE_CLI
cliInit(&masterConfig.serialConfig);
#endif
failsafeInit(&masterConfig.rxConfig, masterConfig.flight3DConfig.deadband3d_throttle);
rxInit(&masterConfig.rxConfig, currentProfile->modeActivationConditions);
#ifdef GPS
if (feature(FEATURE_GPS)) {
gpsInit(
&masterConfig.serialConfig,
&masterConfig.gpsConfig
);
}
#endif
#ifdef NAV
navigationInit(
&masterConfig.navConfig,
¤tProfile->pidProfile,
¤tProfile->rcControlsConfig,
&masterConfig.rxConfig,
&masterConfig.flight3DConfig,
&masterConfig.escAndServoConfig
);
#endif
#ifdef LED_STRIP
ledStripInit(masterConfig.ledConfigs, masterConfig.colors, masterConfig.modeColors, &masterConfig.specialColors);
if (feature(FEATURE_LED_STRIP)) {
ledStripEnable();
}
#endif
#ifdef TELEMETRY
if (feature(FEATURE_TELEMETRY)) {
telemetryInit();
}
#endif
#ifdef USE_FLASHFS
#ifdef NAZE
if (hardwareRevision == NAZE32_REV5) {
m25p16_init();
}
#elif defined(USE_FLASH_M25P16)
m25p16_init();
#endif
flashfsInit();
#endif
#ifdef USE_SDCARD
bool sdcardUseDMA = false;
sdcardInsertionDetectInit();
#ifdef SDCARD_DMA_CHANNEL_TX
#if defined(LED_STRIP) && defined(WS2811_DMA_CHANNEL)
// Ensure the SPI Tx DMA doesn't overlap with the led strip
sdcardUseDMA = !feature(FEATURE_LED_STRIP) || SDCARD_DMA_CHANNEL_TX != WS2811_DMA_CHANNEL;
#else
sdcardUseDMA = true;
#endif
#endif
sdcard_init(sdcardUseDMA);
afatfs_init();
#endif
#ifdef BLACKBOX
initBlackbox();
#endif
gyroSetCalibrationCycles(CALIBRATING_GYRO_CYCLES);
#ifdef BARO
baroSetCalibrationCycles(CALIBRATING_BARO_CYCLES);
#endif
// start all timers
// TODO - not implemented yet
timerStart();
ENABLE_STATE(SMALL_ANGLE);
DISABLE_ARMING_FLAG(PREVENT_ARMING);
#ifdef SOFTSERIAL_LOOPBACK
// FIXME this is a hack, perhaps add a FUNCTION_LOOPBACK to support it properly
loopbackPort = (serialPort_t*)&(softSerialPorts[0]);
if (!loopbackPort->vTable) {
loopbackPort = openSoftSerial(0, NULL, 19200, SERIAL_NOT_INVERTED);
}
serialPrint(loopbackPort, "LOOPBACK\r\n");
#endif
// Now that everything has powered up the voltage and cell count be determined.
if (feature(FEATURE_VBAT | FEATURE_CURRENT_METER))
batteryInit(&masterConfig.batteryConfig);
#ifdef CJMCU
LED2_ON;
#endif
// Latch active features AGAIN since some may be modified by init().
latchActiveFeatures();
motorControlEnable = true;
systemState |= SYSTEM_STATE_READY;
}
#ifdef SOFTSERIAL_LOOPBACK
void processLoopback(void) {
if (loopbackPort) {
uint8_t bytesWaiting;
while ((bytesWaiting = serialRxBytesWaiting(loopbackPort))) {
uint8_t b = serialRead(loopbackPort);
serialWrite(loopbackPort, b);
};
}
}
#else
#define processLoopback()
#endif
int main(void)
{
init();
/* Setup scheduler */
schedulerInit();
rescheduleTask(TASK_GYROPID, targetLooptime);
setTaskEnabled(TASK_GYROPID, true);
setTaskEnabled(TASK_SERIAL, true);
#ifdef BEEPER
setTaskEnabled(TASK_BEEPER, true);
#endif
setTaskEnabled(TASK_BATTERY, feature(FEATURE_VBAT) || feature(FEATURE_CURRENT_METER));
setTaskEnabled(TASK_RX, true);
#ifdef GPS
setTaskEnabled(TASK_GPS, feature(FEATURE_GPS));
#endif
#ifdef MAG
setTaskEnabled(TASK_COMPASS, sensors(SENSOR_MAG));
#if defined(MPU6500_SPI_INSTANCE) && defined(USE_MAG_AK8963)
// fixme temporary solution for AK6983 via slave I2C on MPU9250
rescheduleTask(TASK_COMPASS, 1000000 / 40);
#endif
#endif
#ifdef BARO
setTaskEnabled(TASK_BARO, sensors(SENSOR_BARO));
#endif
#ifdef SONAR
setTaskEnabled(TASK_SONAR, sensors(SENSOR_SONAR));
#endif
#ifdef DISPLAY
setTaskEnabled(TASK_DISPLAY, feature(FEATURE_DISPLAY));
#endif
#ifdef TELEMETRY
setTaskEnabled(TASK_TELEMETRY, feature(FEATURE_TELEMETRY));
#endif
#ifdef LED_STRIP
setTaskEnabled(TASK_LEDSTRIP, feature(FEATURE_LED_STRIP));
#endif
while (true) {
scheduler();
processLoopback();
}
}
int main(void)
{
// Stack limit should be less than real stack size, so we
// had chance to recover from limit hit.
mp_stack_set_limit((char*)&_ram_end - (char*)&_heap_end - 1024);
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Global MSP (MCU Support Package) initialization
*/
HAL_Init();
// basic sub-system init
pendsv_init();
timer_tim3_init();
led_init();
soft_reset:
// check if user switch held to select the reset mode
led_state(LED_RED, 1);
led_state(LED_GREEN, 1);
led_state(LED_BLUE, 1);
#if MICROPY_HW_ENABLE_RTC
rtc_init();
#endif
// GC init
gc_init(&_heap_start, &_heap_end);
// Micro Python init
mp_init();
mp_obj_list_init(mp_sys_path, 0);
mp_obj_list_init(mp_sys_argv, 0);
readline_init0();
pin_init0();
extint_init0();
timer_init0();
rng_init0();
i2c_init0();
spi_init0();
uart_init0();
pyb_usb_init0();
usbdbg_init();
if (sensor_init() != 0) {
__fatal_error("Failed to init sensor");
}
/* Export functions to the global python namespace */
mp_store_global(qstr_from_str("randint"), (mp_obj_t)&py_randint_obj);
mp_store_global(qstr_from_str("cpu_freq"), (mp_obj_t)&py_cpu_freq_obj);
mp_store_global(qstr_from_str("Image"), (mp_obj_t)&py_image_load_image_obj);
mp_store_global(qstr_from_str("HaarCascade"), (mp_obj_t)&py_image_load_cascade_obj);
mp_store_global(qstr_from_str("FreakDesc"), (mp_obj_t)&py_image_load_descriptor_obj);
mp_store_global(qstr_from_str("FreakDescSave"), (mp_obj_t)&py_image_save_descriptor_obj);
mp_store_global(qstr_from_str("LBPDesc"), (mp_obj_t)&py_image_load_lbp_obj);
mp_store_global(qstr_from_str("vcp_is_connected"), (mp_obj_t)&py_vcp_is_connected_obj);
if (sdcard_is_present()) {
sdcard_init();
FRESULT res = f_mount(&fatfs, "1:", 1);
if (res != FR_OK) {
__fatal_error("could not mount SD\n");
}
// Set CWD and USB medium to SD
f_chdrive("1:");
pyb_usb_storage_medium = PYB_USB_STORAGE_MEDIUM_SDCARD;
} else {
storage_init();
// try to mount the flash
FRESULT res = f_mount(&fatfs, "0:", 1);
if (res == FR_NO_FILESYSTEM) {
// create a fresh fs
make_flash_fs();
} else if (res != FR_OK) {
__fatal_error("could not access LFS\n");
}
// Set CWD and USB medium to flash
f_chdrive("0:");
pyb_usb_storage_medium = PYB_USB_STORAGE_MEDIUM_FLASH;
}
// turn boot-up LEDs off
led_state(LED_RED, 0);
led_state(LED_GREEN, 0);
led_state(LED_BLUE, 0);
// init USB device to default setting if it was not already configured
if (!(pyb_usb_flags & PYB_USB_FLAG_USB_MODE_CALLED)) {
pyb_usb_dev_init(USBD_VID, USBD_PID_CDC_MSC, USBD_MODE_CDC_MSC, NULL);
}
// Run the main script from the current directory.
FRESULT res = f_stat("main.py", NULL);
if (res == FR_OK) {
if (!pyexec_file("main.py")) {
nlr_buf_t nlr;
if (nlr_push(&nlr) == 0) {
flash_error(3);
nlr_pop();
}
}
}
// Enter REPL
nlr_buf_t nlr;
for (;;) {
if (nlr_push(&nlr) == 0) {
while (usbdbg_script_ready()) {
nlr_buf_t nlr;
vstr_t *script_buf = usbdbg_get_script();
// clear script flag
usbdbg_clr_script();
// execute the script
if (nlr_push(&nlr) == 0) {
pyexec_push_scope();
// parse and compile script
mp_lexer_t *lex = mp_lexer_new_from_str_len(MP_QSTR__lt_stdin_gt_,
vstr_str(script_buf), vstr_len(script_buf), 0);
mp_parse_node_t pn = mp_parse(lex, MP_PARSE_FILE_INPUT);
mp_obj_t script = mp_compile(pn, lex->source_name, MP_EMIT_OPT_NONE, false);
// execute the script
mp_call_function_0(script);
nlr_pop();
} else {
mp_obj_print_exception(&mp_plat_print, (mp_obj_t)nlr.ret_val);
}
pyexec_pop_scope();
}
// clear script flag
usbdbg_clr_script();
// no script run REPL
pyexec_friendly_repl();
nlr_pop();
}
}
printf("PYB: sync filesystems\n");
storage_flush();
printf("PYB: soft reboot\n");
goto soft_reset;
}
int main(void)
{
FRESULT f_res;
int sensor_init_ret;
// Stack limit should be less than real stack size, so we
// had chance to recover from limit hit.
mp_stack_set_limit((char*)&_ram_end - (char*)&_heap_end - 1024);
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Global MSP (MCU Support Package) initialization
*/
HAL_Init();
// basic sub-system init
pendsv_init();
timer_tim3_init();
led_init();
soft_reset:
// check if user switch held to select the reset mode
led_state(LED_RED, 1);
led_state(LED_GREEN, 1);
led_state(LED_BLUE, 1);
#if MICROPY_HW_ENABLE_RTC
rtc_init();
#endif
// GC init
gc_init(&_heap_start, &_heap_end);
// Micro Python init
mp_init();
mp_obj_list_init(mp_sys_path, 0);
mp_obj_list_init(mp_sys_argv, 0);
readline_init0();
pin_init0();
extint_init0();
timer_init0();
rng_init0();
i2c_init0();
spi_init0();
uart_init0();
pyb_usb_init0();
usbdbg_init();
sensor_init_ret = sensor_init();
/* Export functions to the global python namespace */
mp_store_global(qstr_from_str("randint"), (mp_obj_t)&py_randint_obj);
mp_store_global(qstr_from_str("cpu_freq"), (mp_obj_t)&py_cpu_freq_obj);
mp_store_global(qstr_from_str("vcp_is_connected"), (mp_obj_t)&py_vcp_is_connected_obj);
if (sdcard_is_present()) {
sdcard_init();
FRESULT res = f_mount(&fatfs, "1:", 1);
if (res != FR_OK) {
__fatal_error("could not mount SD\n");
}
// Set CWD and USB medium to SD
f_chdrive("1:");
pyb_usb_storage_medium = PYB_USB_STORAGE_MEDIUM_SDCARD;
} else {
storage_init();
// try to mount the flash
FRESULT res = f_mount(&fatfs, "0:", 1);
if (res == FR_NO_FILESYSTEM) {
// create a fresh fs
make_flash_fs();
} else if (res != FR_OK) {
__fatal_error("could not access LFS\n");
}
// Set CWD and USB medium to flash
f_chdrive("0:");
pyb_usb_storage_medium = PYB_USB_STORAGE_MEDIUM_FLASH;
}
// turn boot-up LEDs off
led_state(LED_RED, 0);
led_state(LED_GREEN, 0);
led_state(LED_BLUE, 0);
// init USB device to default setting if it was not already configured
if (!(pyb_usb_flags & PYB_USB_FLAG_USB_MODE_CALLED)) {
pyb_usb_dev_init(USBD_VID, USBD_PID_CDC_MSC, USBD_MODE_CDC_MSC, NULL);
}
// check sensor init result
if (sensor_init_ret != 0) {
char buf[512];
snprintf(buf, sizeof(buf), "Failed to init sensor, error:%d", sensor_init_ret);
__fatal_error(buf);
}
// Run self tests the first time only
f_res = f_stat("selftest.py", NULL);
if (f_res == FR_OK) {
nlr_buf_t nlr;
if (nlr_push(&nlr) == 0) {
// Parse, compile and execute the self-tests script.
pyexec_file("selftest.py");
nlr_pop();
} else {
// Get the exception message. TODO: might be a hack.
mp_obj_str_t *str = mp_obj_exception_get_value((mp_obj_t)nlr.ret_val);
// If any of the self-tests fail log the exception message
// and loop forever. Note: IDE exceptions will not be caught.
__fatal_error((const char*) str->data);
}
// Success: remove self tests script and flush cache
f_unlink("selftest.py");
storage_flush();
}
// Run the main script from the current directory.
f_res = f_stat("main.py", NULL);
if (f_res == FR_OK) {
nlr_buf_t nlr;
if (nlr_push(&nlr) == 0) {
// Parse, compile and execute the main script.
pyexec_file("main.py");
nlr_pop();
} else {
mp_obj_print_exception(&mp_plat_print, (mp_obj_t)nlr.ret_val);
if (nlr_push(&nlr) == 0) {
flash_error(3);
nlr_pop();
}// if this gets interrupted again ignore it.
}
}
// Enter REPL
nlr_buf_t nlr;
for (;;) {
if (nlr_push(&nlr) == 0) {
while (usbdbg_script_ready()) {
nlr_buf_t nlr;
vstr_t *script_buf = usbdbg_get_script();
// clear debugging flags
usbdbg_clear_flags();
// re-init MP
mp_uint_t atomic_state = MICROPY_BEGIN_ATOMIC_SECTION();
mp_init();
MICROPY_END_ATOMIC_SECTION(atomic_state);
// execute the script
if (nlr_push(&nlr) == 0) {
// parse, compile and execute script
pyexec_str(script_buf);
nlr_pop();
} else {
mp_obj_print_exception(&mp_plat_print, (mp_obj_t)nlr.ret_val);
}
}
// clear debugging flags
usbdbg_clear_flags();
// re-init MP
mp_uint_t atomic_state = MICROPY_BEGIN_ATOMIC_SECTION();
mp_init();
MICROPY_END_ATOMIC_SECTION(atomic_state);
// no script run REPL
pyexec_friendly_repl();
nlr_pop();
}
}
printf("PYB: sync filesystems\n");
storage_flush();
printf("PYB: soft reboot\n");
goto soft_reset;
}
int main(void) {
// copy vector table to SRAM1!
#pragma GCC diagnostic push
#pragma GCC diagnostic ignored "-Wnonnull"
memcpy((char *)0x20000000, (const char)0x00000000, 0x200);
#pragma GCC diagnostic pop
// remap SRAM1 to 0x00000000
SYSCFG->MEMRMP |= 0x03;
halInit();
chSysInit();
sdcard_init();
sysmon_init();
#if ENABLE_SERIAL_DEBUG
// SD2 for serial debug output
palSetPadMode(GPIOA, 3, PAL_MODE_ALTERNATE(7) | PAL_MODE_INPUT); // RX
palSetPadMode(GPIOA, 2, PAL_MODE_OUTPUT_PUSHPULL); // TX
palSetPadMode(GPIOA, 2, PAL_MODE_ALTERNATE(7)); // TX
// 115200 baud
static const SerialConfig sd2Cfg = {115200,
0, 0, 0};
sdStart(&SD2, &sd2Cfg);
chprintf((BaseSequentialStream * )&SD2,"Hello world!\r\n");
#endif
exception_init();
InitPatch0();
InitPConnection();
InitPWM();
// display SPI CS?
palSetPadMode(GPIOC, 1, PAL_MODE_OUTPUT_PUSHPULL);
palSetPad(GPIOC, 1);
chThdSleepMilliseconds(10);
palSetPadMode(SW2_PORT, SW2_PIN, PAL_MODE_INPUT_PULLDOWN);
axoloti_board_init();
codec_init();
if (!palReadPad(SW2_PORT, SW2_PIN)) { // button S2 not pressed
// watchdog_init();
chThdSleepMilliseconds(1);
}
start_dsp_thread();
adc_init();
axoloti_math_init();
midi_init();
#if ((BOARD_AXOLOTI_V03)||(BOARD_AXOLOTI_V05))
axoloti_control_init();
#endif
ui_init();
StartLoadPatchTread();
#if (BOARD_AXOLOTI_V05)
configSDRAM();
//memTest();
#endif
#ifdef ENABLE_USB_HOST
MY_USBH_Init();
#endif
if (!exception_check()) {
// only try booting a patch when no exception is to be reported
#if ((BOARD_AXOLOTI_V03)||(BOARD_AXOLOTI_V05))
sdcard_attemptMountIfUnmounted();
if (fs_ready && !palReadPad(SW2_PORT, SW2_PIN)){
// button S2 not pressed
FRESULT res;
// res = f_stat("/start.bin", NULL);
// if (res == FR_OK) {
LoadPatch("/start.bin");
// }
}
#endif
// if no patch booting or running yet
// try loading from flash
if (patchStatus) {
// patch in flash sector 11
memcpy((uint8_t *)PATCHMAINLOC, (uint8_t *)PATCHFLASHLOC, PATCHFLASHSIZE);
if ((*(uint32_t *)PATCHMAINLOC != 0xFFFFFFFF)
&& (*(uint32_t *)PATCHMAINLOC != 0)) {
if (!palReadPad(SW2_PORT, SW2_PIN)) // button S2 not pressed
StartPatch();
}
}
}
while (1) {
chThdSleepMilliseconds(1000);
}
}
int main(void) {
// TODO disable JTAG
// update the SystemCoreClock variable
SystemCoreClockUpdate();
// set interrupt priority config to use all 4 bits for pre-empting
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_4);
// enable the CCM RAM and the GPIO's
RCC->AHB1ENR |= RCC_AHB1ENR_CCMDATARAMEN | RCC_AHB1ENR_GPIOAEN | RCC_AHB1ENR_GPIOBEN | RCC_AHB1ENR_GPIOCEN | RCC_AHB1ENR_GPIODEN;
#if MICROPY_HW_HAS_SDCARD
{
// configure SDIO pins to be high to start with (apparently makes it more robust)
// FIXME this is not making them high, it just makes them outputs...
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10 | GPIO_Pin_11 | GPIO_Pin_12;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_25MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(GPIOC, &GPIO_InitStructure);
// Configure PD.02 CMD line
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
GPIO_Init(GPIOD, &GPIO_InitStructure);
}
#endif
#if defined(NETDUINO_PLUS_2)
{
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_25MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
#if MICROPY_HW_HAS_SDCARD
// Turn on the power enable for the sdcard (PB1)
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_WriteBit(GPIOB, GPIO_Pin_1, Bit_SET);
#endif
// Turn on the power for the 5V on the expansion header (PB2)
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_WriteBit(GPIOB, GPIO_Pin_2, Bit_SET);
}
#endif
// basic sub-system init
sys_tick_init();
pendsv_init();
led_init();
#if MICROPY_HW_ENABLE_RTC
rtc_init();
#endif
// turn on LED to indicate bootup
led_state(PYB_LED_G1, 1);
// more sub-system init
#if MICROPY_HW_HAS_SDCARD
sdcard_init();
#endif
storage_init();
// uncomment these 2 lines if you want REPL on USART_6 (or another usart) as well as on USB VCP
//pyb_usart_global_debug = PYB_USART_YA;
//usart_init(pyb_usart_global_debug, 115200);
int first_soft_reset = true;
soft_reset:
// GC init
gc_init(&_heap_start, &_heap_end);
// Micro Python init
qstr_init();
mp_init();
mp_obj_list_init(mp_sys_path, 0);
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR_0_colon__slash_));
mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR_0_colon__slash_lib));
mp_obj_list_init(mp_sys_argv, 0);
exti_init();
#if MICROPY_HW_HAS_SWITCH
switch_init();
#endif
#if MICROPY_HW_HAS_LCD
// LCD init (just creates class, init hardware by calling LCD())
lcd_init();
#endif
#if MICROPY_HW_ENABLE_SERVO
// servo
servo_init();
#endif
#if MICROPY_HW_ENABLE_TIMER
// timer
timer_init();
#endif
#if MICROPY_HW_ENABLE_RNG
// RNG
RCC_AHB2PeriphClockCmd(RCC_AHB2Periph_RNG, ENABLE);
RNG_Cmd(ENABLE);
#endif
pin_map_init();
// add some functions to the builtin Python namespace
mp_store_name(MP_QSTR_help, mp_make_function_n(0, pyb_help));
mp_store_name(MP_QSTR_open, mp_make_function_n(2, pyb_io_open));
// load the pyb module
mp_module_register(MP_QSTR_pyb, (mp_obj_t)&pyb_module);
// check if user switch held (initiates reset of filesystem)
bool reset_filesystem = false;
#if MICROPY_HW_HAS_SWITCH
if (switch_get()) {
reset_filesystem = true;
for (int i = 0; i < 50; i++) {
if (!switch_get()) {
reset_filesystem = false;
break;
}
sys_tick_delay_ms(10);
}
}
#endif
// local filesystem init
{
// try to mount the flash
FRESULT res = f_mount(&fatfs0, "0:", 1);
if (!reset_filesystem && res == FR_OK) {
// mount sucessful
} else if (reset_filesystem || res == FR_NO_FILESYSTEM) {
// no filesystem, so create a fresh one
// TODO doesn't seem to work correctly when reset_filesystem is true...
// LED on to indicate creation of LFS
led_state(PYB_LED_R2, 1);
uint32_t stc = sys_tick_counter;
res = f_mkfs("0:", 0, 0);
if (res == FR_OK) {
// success creating fresh LFS
} else {
__fatal_error("could not create LFS");
}
// create src directory
res = f_mkdir("0:/src");
// ignore result from mkdir
// create empty main.py
FIL fp;
f_open(&fp, "0:/src/main.py", FA_WRITE | FA_CREATE_ALWAYS);
UINT n;
f_write(&fp, fresh_main_py, sizeof(fresh_main_py) - 1 /* don't count null terminator */, &n);
// TODO check we could write n bytes
f_close(&fp);
// keep LED on for at least 200ms
sys_tick_wait_at_least(stc, 200);
led_state(PYB_LED_R2, 0);
} else {
__fatal_error("could not access LFS");
}
}
// make sure we have a /boot.py
{
FILINFO fno;
FRESULT res = f_stat("0:/boot.py", &fno);
if (res == FR_OK) {
if (fno.fattrib & AM_DIR) {
// exists as a directory
// TODO handle this case
// see http://elm-chan.org/fsw/ff/img/app2.c for a "rm -rf" implementation
} else {
// exists as a file, good!
}
} else {
// doesn't exist, create fresh file
// LED on to indicate creation of boot.py
led_state(PYB_LED_R2, 1);
uint32_t stc = sys_tick_counter;
FIL fp;
f_open(&fp, "0:/boot.py", FA_WRITE | FA_CREATE_ALWAYS);
UINT n;
f_write(&fp, fresh_boot_py, sizeof(fresh_boot_py) - 1 /* don't count null terminator */, &n);
// TODO check we could write n bytes
f_close(&fp);
// keep LED on for at least 200ms
sys_tick_wait_at_least(stc, 200);
led_state(PYB_LED_R2, 0);
}
}
// run /boot.py
if (!pyexec_file("0:/boot.py")) {
flash_error(4);
}
if (first_soft_reset) {
#if MICROPY_HW_HAS_MMA7660
// MMA accel: init and reset address to zero
accel_init();
#endif
}
// turn boot-up LED off
led_state(PYB_LED_G1, 0);
#if MICROPY_HW_HAS_SDCARD
// if an SD card is present then mount it on 1:/
if (sdcard_is_present()) {
FRESULT res = f_mount(&fatfs1, "1:", 1);
if (res != FR_OK) {
printf("[SD] could not mount SD card\n");
} else {
if (first_soft_reset) {
// use SD card as medium for the USB MSD
usbd_storage_select_medium(USBD_STORAGE_MEDIUM_SDCARD);
}
}
}
#endif
#ifdef USE_HOST_MODE
// USB host
pyb_usb_host_init();
#elif defined(USE_DEVICE_MODE)
// USB device
pyb_usb_dev_init(PYB_USB_DEV_VCP_MSC);
#endif
// run main script
{
vstr_t *vstr = vstr_new();
vstr_add_str(vstr, "0:/");
if (pyb_config_source_dir == MP_OBJ_NULL) {
vstr_add_str(vstr, "src");
} else {
vstr_add_str(vstr, mp_obj_str_get_str(pyb_config_source_dir));
}
vstr_add_char(vstr, '/');
if (pyb_config_main == MP_OBJ_NULL) {
vstr_add_str(vstr, "main.py");
} else {
vstr_add_str(vstr, mp_obj_str_get_str(pyb_config_main));
}
if (!pyexec_file(vstr_str(vstr))) {
flash_error(3);
}
vstr_free(vstr);
}
#if MICROPY_HW_HAS_MMA7660
// HID example
if (0) {
uint8_t data[4];
data[0] = 0;
data[1] = 1;
data[2] = -2;
data[3] = 0;
for (;;) {
#if MICROPY_HW_HAS_SWITCH
if (switch_get()) {
data[0] = 0x01; // 0x04 is middle, 0x02 is right
} else {
data[0] = 0x00;
}
#else
data[0] = 0x00;
#endif
accel_start(0x4c /* ACCEL_ADDR */, 1);
accel_send_byte(0);
accel_restart(0x4c /* ACCEL_ADDR */, 0);
for (int i = 0; i <= 1; i++) {
int v = accel_read_ack() & 0x3f;
if (v & 0x20) {
v |= ~0x1f;
}
data[1 + i] = v;
}
accel_read_nack();
usb_hid_send_report(data);
sys_tick_delay_ms(15);
}
}
#endif
#if MICROPY_HW_HAS_WLAN
// wifi
pyb_wlan_init();
pyb_wlan_start();
#endif
pyexec_repl();
printf("PYB: sync filesystems\n");
storage_flush();
printf("PYB: soft reboot\n");
first_soft_reset = false;
goto soft_reset;
}
/* Main function
*
* - Initialise device and any global variables
* - Enable Interrupts
* - Start endless loop
*/
void main(void) {
unsigned long ulRetcode;
// Initialise the device clock to 80MHz
ROM_SysCtlClockSet(SYSCTL_SYSDIV_2_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ | SYSCTL_OSC_MAIN );
// Enable SysTick for FatFS at 10ms intervals
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / 100);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Configure and enable uDMA
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UDMA);
SysCtlDelay(10);
ROM_uDMAControlBaseSet(&sDMAControlTable[0]);
ROM_uDMAEnable();
//
// Enable the USB controller.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
//
// Set the USB pins to be controlled by the USB controller.
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_4 | GPIO_PIN_5);
// Initialize the idle timeout and reset all flags.
//
g_ulIdleTimeout = 0;
g_ulFlags = 0;
//
// Initialize the state to idle.
//
g_eMSCState = MSC_DEV_DISCONNECTED;
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, USB_MODE_DEVICE, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDMSCInit(0, (tUSBDMSCDevice *)&g_sMSCDevice);
//
// Determine whether or not an SDCard is installed. If not, print a
// warning and have the user install one and restart.
//
ulRetcode = disk_initialize(0);
// Enable Global interrupts
ROM_IntMasterEnable();
// Enable floating point arithmetic unit, but disable stacking
ROM_FPUEnable();
ROM_FPUStackingDisable();
// Initialise GPIO - All ports enabled
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
// Unlock NMI pins for GPIO usage (PD7 + PF0)
HWREG(GPIO_PORTD_BASE + 0x520) = 0x4C4F434B;
HWREG(GPIO_PORTF_BASE + 0x520) = 0x4C4F434B;
HWREG(GPIO_PORTD_BASE + 0x524) = 0x000000FF;
HWREG(GPIO_PORTF_BASE + 0x524) = 0x000000FF;
HWREG(GPIO_PORTD_BASE + 0x520) = 0x00000000;
HWREG(GPIO_PORTF_BASE + 0x520) = 0x00000000;
// Initialise GPIO Expander (probably not happening)
// Initialise Buttons
btn_init();
// Initialise FX
fx_init();
// Initialise ADC
adc_init();
// Initialise DAC
dac_init();
// Initialise SD Card and Mass storage
sdcard_init();
// Initialise UART for debugging
uart_init();
// Initialise Timers
timers_init();
for(;;) {
// Endless Loop
ADCProcessorTrigger(ADC0_BASE, 0);
SysCtlDelay(SysCtlClockGet() / 120); // 25ms
}
}
void init(void)
{
#ifdef USE_HAL_DRIVER
HAL_Init();
#endif
printfSupportInit();
initEEPROM();
ensureEEPROMContainsValidData();
readEEPROM();
systemState |= SYSTEM_STATE_CONFIG_LOADED;
systemInit();
//i2cSetOverclock(masterConfig.i2c_overclock);
// initialize IO (needed for all IO operations)
IOInitGlobal();
debugMode = masterConfig.debug_mode;
#ifdef USE_HARDWARE_REVISION_DETECTION
detectHardwareRevision();
#endif
// Latch active features to be used for feature() in the remainder of init().
latchActiveFeatures();
#ifdef ALIENFLIGHTF3
ledInit(hardwareRevision == AFF3_REV_1 ? false : true);
#else
ledInit(false);
#endif
LED2_ON;
#ifdef USE_EXTI
EXTIInit();
#endif
#if defined(BUTTONS)
gpio_config_t buttonAGpioConfig = {
BUTTON_A_PIN,
Mode_IPU,
Speed_2MHz
};
gpioInit(BUTTON_A_PORT, &buttonAGpioConfig);
gpio_config_t buttonBGpioConfig = {
BUTTON_B_PIN,
Mode_IPU,
Speed_2MHz
};
gpioInit(BUTTON_B_PORT, &buttonBGpioConfig);
// Check status of bind plug and exit if not active
delayMicroseconds(10); // allow GPIO configuration to settle
if (!isMPUSoftReset()) {
uint8_t secondsRemaining = 5;
bool bothButtonsHeld;
do {
bothButtonsHeld = !digitalIn(BUTTON_A_PORT, BUTTON_A_PIN) && !digitalIn(BUTTON_B_PORT, BUTTON_B_PIN);
if (bothButtonsHeld) {
if (--secondsRemaining == 0) {
resetEEPROM();
systemReset();
}
delay(1000);
LED0_TOGGLE;
}
} while (bothButtonsHeld);
}
#endif
#ifdef SPEKTRUM_BIND
if (feature(FEATURE_RX_SERIAL)) {
switch (masterConfig.rxConfig.serialrx_provider) {
case SERIALRX_SPEKTRUM1024:
case SERIALRX_SPEKTRUM2048:
// Spektrum satellite binding if enabled on startup.
// Must be called before that 100ms sleep so that we don't lose satellite's binding window after startup.
// The rest of Spektrum initialization will happen later - via spektrumInit()
spektrumBind(&masterConfig.rxConfig);
break;
}
}
#endif
delay(100);
timerInit(); // timer must be initialized before any channel is allocated
#if !defined(USE_HAL_DRIVER)
dmaInit();
#endif
#if defined(AVOID_UART1_FOR_PWM_PPM)
serialInit(&masterConfig.serialConfig, feature(FEATURE_SOFTSERIAL),
feature(FEATURE_RX_PPM) || feature(FEATURE_RX_PARALLEL_PWM) ? SERIAL_PORT_USART1 : SERIAL_PORT_NONE);
#elif defined(AVOID_UART2_FOR_PWM_PPM)
serialInit(&masterConfig.serialConfig, feature(FEATURE_SOFTSERIAL),
feature(FEATURE_RX_PPM) || feature(FEATURE_RX_PARALLEL_PWM) ? SERIAL_PORT_USART2 : SERIAL_PORT_NONE);
#elif defined(AVOID_UART3_FOR_PWM_PPM)
serialInit(&masterConfig.serialConfig, feature(FEATURE_SOFTSERIAL),
feature(FEATURE_RX_PPM) || feature(FEATURE_RX_PARALLEL_PWM) ? SERIAL_PORT_USART3 : SERIAL_PORT_NONE);
#else
serialInit(&masterConfig.serialConfig, feature(FEATURE_SOFTSERIAL), SERIAL_PORT_NONE);
#endif
mixerInit(masterConfig.mixerMode, masterConfig.customMotorMixer);
#ifdef USE_SERVOS
servoMixerInit(masterConfig.customServoMixer);
#endif
uint16_t idlePulse = masterConfig.motorConfig.mincommand;
if (feature(FEATURE_3D)) {
idlePulse = masterConfig.flight3DConfig.neutral3d;
}
if (masterConfig.motorConfig.motorPwmProtocol == PWM_TYPE_BRUSHED) {
featureClear(FEATURE_3D);
idlePulse = 0; // brushed motors
}
#ifdef USE_QUAD_MIXER_ONLY
motorInit(&masterConfig.motorConfig, idlePulse, QUAD_MOTOR_COUNT);
#else
motorInit(&masterConfig.motorConfig, idlePulse, mixers[masterConfig.mixerMode].motorCount);
#endif
#ifdef USE_SERVOS
if (isMixerUsingServos()) {
//pwm_params.useChannelForwarding = feature(FEATURE_CHANNEL_FORWARDING);
servoInit(&masterConfig.servoConfig);
}
#endif
#ifndef SKIP_RX_PWM_PPM
if (feature(FEATURE_RX_PPM)) {
ppmRxInit(&masterConfig.ppmConfig, masterConfig.motorConfig.motorPwmProtocol);
} else if (feature(FEATURE_RX_PARALLEL_PWM)) {
pwmRxInit(&masterConfig.pwmConfig);
}
pwmRxSetInputFilteringMode(masterConfig.inputFilteringMode);
#endif
mixerConfigureOutput();
#ifdef USE_SERVOS
servoConfigureOutput();
#endif
systemState |= SYSTEM_STATE_MOTORS_READY;
#ifdef BEEPER
beeperInit(&masterConfig.beeperConfig);
#endif
/* temp until PGs are implemented. */
#ifdef INVERTER
initInverter();
#endif
#ifdef USE_BST
bstInit(BST_DEVICE);
#endif
#ifdef USE_SPI
#ifdef USE_SPI_DEVICE_1
spiInit(SPIDEV_1);
#endif
#ifdef USE_SPI_DEVICE_2
spiInit(SPIDEV_2);
#endif
#ifdef USE_SPI_DEVICE_3
#ifdef ALIENFLIGHTF3
if (hardwareRevision == AFF3_REV_2) {
spiInit(SPIDEV_3);
}
#else
spiInit(SPIDEV_3);
#endif
#endif
#ifdef USE_SPI_DEVICE_4
spiInit(SPIDEV_4);
#endif
#endif
#ifdef VTX
vtxInit();
#endif
#ifdef USE_HARDWARE_REVISION_DETECTION
updateHardwareRevision();
#endif
#if defined(NAZE)
if (hardwareRevision == NAZE32_SP) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
} else {
serialRemovePort(SERIAL_PORT_USART3);
}
#endif
#if defined(SPRACINGF3) && defined(SONAR) && defined(USE_SOFTSERIAL2)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
}
#endif
#if defined(SPRACINGF3MINI) || defined(OMNIBUS) || defined(X_RACERSPI)
#if defined(SONAR) && defined(USE_SOFTSERIAL1)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL1);
}
#endif
#endif
#ifdef USE_I2C
#if defined(NAZE)
if (hardwareRevision != NAZE32_SP) {
i2cInit(I2C_DEVICE);
} else {
if (!doesConfigurationUsePort(SERIAL_PORT_USART3)) {
i2cInit(I2C_DEVICE);
}
}
#elif defined(CC3D)
if (!doesConfigurationUsePort(SERIAL_PORT_USART3)) {
i2cInit(I2C_DEVICE);
}
#else
i2cInit(I2C_DEVICE);
#endif
#endif
#ifdef USE_ADC
drv_adc_config_t adc_params;
adc_params.enableVBat = feature(FEATURE_VBAT);
adc_params.enableRSSI = feature(FEATURE_RSSI_ADC);
adc_params.enableCurrentMeter = feature(FEATURE_CURRENT_METER);
adc_params.enableExternal1 = false;
#ifdef OLIMEXINO
adc_params.enableExternal1 = true;
#endif
#ifdef NAZE
// optional ADC5 input on rev.5 hardware
adc_params.enableExternal1 = (hardwareRevision >= NAZE32_REV5);
#endif
adcInit(&adc_params);
#endif
initBoardAlignment(&masterConfig.boardAlignment);
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
displayInit(&masterConfig.rxConfig);
}
#endif
#ifdef USE_RTC6705
if (feature(FEATURE_VTX)) {
rtc6705_soft_spi_init();
current_vtx_channel = masterConfig.vtx_channel;
rtc6705_soft_spi_set_channel(vtx_freq[current_vtx_channel]);
rtc6705_soft_spi_set_rf_power(masterConfig.vtx_power);
}
#endif
#ifdef OSD
if (feature(FEATURE_OSD)) {
osdInit();
}
#endif
if (!sensorsAutodetect(&masterConfig.sensorAlignmentConfig,
masterConfig.acc_hardware,
masterConfig.mag_hardware,
masterConfig.baro_hardware,
masterConfig.mag_declination,
masterConfig.gyro_lpf,
masterConfig.gyro_sync_denom)) {
// if gyro was not detected due to whatever reason, we give up now.
failureMode(FAILURE_MISSING_ACC);
}
systemState |= SYSTEM_STATE_SENSORS_READY;
LED1_ON;
LED0_OFF;
LED2_OFF;
for (int i = 0; i < 10; i++) {
LED1_TOGGLE;
LED0_TOGGLE;
delay(25);
if (!(getBeeperOffMask() & (1 << (BEEPER_SYSTEM_INIT - 1)))) BEEP_ON;
delay(25);
BEEP_OFF;
}
LED0_OFF;
LED1_OFF;
#ifdef MAG
if (sensors(SENSOR_MAG))
compassInit();
#endif
imuInit();
mspFcInit();
mspSerialInit();
#ifdef USE_CLI
cliInit(&masterConfig.serialConfig);
#endif
failsafeInit(&masterConfig.rxConfig, masterConfig.flight3DConfig.deadband3d_throttle);
rxInit(&masterConfig.rxConfig, masterConfig.modeActivationConditions);
#ifdef GPS
if (feature(FEATURE_GPS)) {
gpsInit(
&masterConfig.serialConfig,
&masterConfig.gpsConfig
);
navigationInit(
&masterConfig.gpsProfile,
¤tProfile->pidProfile
);
}
#endif
#ifdef SONAR
if (feature(FEATURE_SONAR)) {
sonarInit(&masterConfig.sonarConfig);
}
#endif
#ifdef LED_STRIP
ledStripInit(masterConfig.ledConfigs, masterConfig.colors, masterConfig.modeColors, &masterConfig.specialColors);
if (feature(FEATURE_LED_STRIP)) {
ledStripEnable();
}
#endif
#ifdef TELEMETRY
if (feature(FEATURE_TELEMETRY)) {
telemetryInit();
}
#endif
#ifdef USB_CABLE_DETECTION
usbCableDetectInit();
#endif
#ifdef TRANSPONDER
if (feature(FEATURE_TRANSPONDER)) {
transponderInit(masterConfig.transponderData);
transponderEnable();
transponderStartRepeating();
systemState |= SYSTEM_STATE_TRANSPONDER_ENABLED;
}
#endif
#ifdef USE_FLASHFS
#ifdef NAZE
if (hardwareRevision == NAZE32_REV5) {
m25p16_init(IO_TAG_NONE);
}
#elif defined(USE_FLASH_M25P16)
m25p16_init(IO_TAG_NONE);
#endif
flashfsInit();
#endif
#ifdef USE_SDCARD
bool sdcardUseDMA = false;
sdcardInsertionDetectInit();
#ifdef SDCARD_DMA_CHANNEL_TX
#if defined(LED_STRIP) && defined(WS2811_DMA_CHANNEL)
// Ensure the SPI Tx DMA doesn't overlap with the led strip
#if defined(STM32F4) || defined(STM32F7)
sdcardUseDMA = !feature(FEATURE_LED_STRIP) || SDCARD_DMA_CHANNEL_TX != WS2811_DMA_STREAM;
#else
sdcardUseDMA = !feature(FEATURE_LED_STRIP) || SDCARD_DMA_CHANNEL_TX != WS2811_DMA_CHANNEL;
#endif
#else
sdcardUseDMA = true;
#endif
#endif
sdcard_init(sdcardUseDMA);
afatfs_init();
#endif
if (masterConfig.gyro_lpf > 0 && masterConfig.gyro_lpf < 7) {
masterConfig.pid_process_denom = 1; // When gyro set to 1khz always set pid speed 1:1 to sampling speed
masterConfig.gyro_sync_denom = 1;
}
setTargetPidLooptime((gyro.targetLooptime + LOOPTIME_SUSPEND_TIME) * masterConfig.pid_process_denom); // Initialize pid looptime
#ifdef BLACKBOX
initBlackbox();
#endif
if (masterConfig.mixerMode == MIXER_GIMBAL) {
accSetCalibrationCycles(CALIBRATING_ACC_CYCLES);
}
gyroSetCalibrationCycles();
#ifdef BARO
baroSetCalibrationCycles(CALIBRATING_BARO_CYCLES);
#endif
// start all timers
// TODO - not implemented yet
timerStart();
ENABLE_STATE(SMALL_ANGLE);
DISABLE_ARMING_FLAG(PREVENT_ARMING);
#ifdef SOFTSERIAL_LOOPBACK
// FIXME this is a hack, perhaps add a FUNCTION_LOOPBACK to support it properly
loopbackPort = (serialPort_t*)&(softSerialPorts[0]);
if (!loopbackPort->vTable) {
loopbackPort = openSoftSerial(0, NULL, 19200, SERIAL_NOT_INVERTED);
}
serialPrint(loopbackPort, "LOOPBACK\r\n");
#endif
// Now that everything has powered up the voltage and cell count be determined.
if (feature(FEATURE_VBAT | FEATURE_CURRENT_METER))
batteryInit(&masterConfig.batteryConfig);
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
#ifdef USE_OLED_GPS_DEBUG_PAGE_ONLY
displayShowFixedPage(PAGE_GPS);
#else
displayResetPageCycling();
displayEnablePageCycling();
#endif
}
#endif
#ifdef CJMCU
LED2_ON;
#endif
// Latch active features AGAIN since some may be modified by init().
latchActiveFeatures();
motorControlEnable = true;
fcTasksInit();
systemState |= SYSTEM_STATE_READY;
}
DSTATUS disk_initialize (
BYTE drv /* Physical drive nmuber (0) */
)
{
// BYTE n, cmd, ty, ocr[4];
UINT cmd, n;
DWORD resp[4];
BYTE ty;
SDC_PRMS_T params;
if (!sdcard_init(¶ms)) {
return STA_NOINIT;
}
if (drv) return STA_NOINIT; /* Supports only single drive */
if (Stat & STA_NODISK) return Stat; /* No card in the socket */
power_on(); /* Force socket power on */
for (Timer1 = 2; Timer1; );
send_cmd(CMD0, 0, 0, NULL); /* Enter idle state */
CardRCA = 0;
Timer1 = 10;
while(Timer1);
/*---- Card is 'idle' state ----*/
Timer1 = 100; /* Initialization timeout of 1000 msec */
if (send_cmd(CMD8, 0x1AA, 1, resp) /* SDC Ver2 */
&& (resp[0] & 0xFFF) == 0x1AA) { /* The card can work at vdd range of 2.7-3.6V */
do { /* Wait while card is busy state (use ACMD41 with HCS bit) */
/* This loop will take a time. Insert wai_tsk(1) here for multitask envilonment. */
if (!Timer1) goto di_fail;
} while (!send_cmd(ACMD41, 0x40FF8000, 1, resp) || !(resp[0] & 0x80000000));
ty = (resp[0] & 0x40000000) ? CT_SD2|CT_BLOCK : CT_SD2; /* Check CCS bit in the OCR */
}
else { /* SDC Ver1 or MMC */
if (send_cmd(ACMD41, /*0x00FF8000*/0, 1, resp)) {
ty = CT_SD1; cmd = ACMD41; /* ACMD41 is accepted -> SDC Ver1 */
} else {
ty = CT_MMC; cmd = CMD1; /* ACMD41 is rejected -> MMC */
}
do { /* Wait while card is busy state (use ACMD41 or CMD1) */
/* This loop will take a time. Insert wai_tsk(1) here for multitask envilonment. */
if (!Timer1) {
Timer1 = Timer1;
goto di_fail;
}
} while (!send_cmd(cmd, 0x00FF8000, 1, resp) || !(resp[0] & 0x80000000));
}
CardType = ty; /* Save card type */
bswap_cp(&CardInfo[32], resp); /* Save OCR */
/*---- Card is 'ready' state ----*/
if (!send_cmd(CMD2, 0, 2, resp)) goto di_fail; /* Enter ident state */
for (n = 0; n < 4; n++) bswap_cp(&CardInfo[n * 4 + 16], &resp[n]); /* Save CID */
/*---- Card is 'ident' state ----*/
if (ty & CT_SDC) { /* SDC: Get generated RCA and save it */
if (!send_cmd(CMD3, 0, 1, resp)) goto di_fail;
CardRCA = (WORD)(resp[0] >> 16);
} else { /* MMC: Assign RCA to the card */
if (!send_cmd(CMD3, 1 << 16, 1, resp)) goto di_fail;
