int8_t uart_startTransceiverTx( uint8_t *msg, uint8_t msg_len, uint8_t flags) {
if (state[TX].state != UART_IDLE) {
//DEBUG("uart_startTransceiverTx Fail!!! ***\n");
return -EBUSY;
}
state[TX].flags = UART_SYS_SHARED_FLAGS_MSK & flags; // get shared flags
if (state[TX].flags & UART_SOS_MSG_FLAG) {
state[TX].msgHdr = (Message*)msg;
state[TX].msgLen = state[TX].msgHdr->len; // if msg->len != msg_len ???
state[TX].buff = state[TX].msgHdr->data;
} else {
state[TX].buff = msg;
state[TX].msgLen = msg_len;
}
state[TX].idx = 0;
state[TX].state = UART_HDLC_START;
state[TX].hdlc_state = HDLC_START;
if(state[TX].msgHdr->type == MSG_TIMESTAMP){
uint32_t timestp = ker_systime32();
memcpy(state[TX].msgHdr->data, (uint8_t*)(×tp),sizeof(uint32_t));
}
uart_enable_tx();
uart_setByte(HDLC_FLAG);
//DEBUG("uart_startTransceiverTx Start!!! ***\n");
return SOS_OK;
}
uint8_t USART_Init(struct USART_configuration config)
{
// Add your code here. Don't forget that this function is supposed
// to return an error code if something goes wrong!
/* Create Buffers */
rx_buf = rb_create(RX_BUFFLEN);
tx_buf = rb_create(TX_BUFFLEN);
/* Enable UART receiver and transmitter */
uart_enable_rx();
uart_enable_tx();
/* Enable UART RX Complete Interrupt */
uart_enable_rx_complete_interrupt();
/* set baudrate */
if (uart_set_baudrate(config.baudrate))
goto error;
/* Parity */
if (uart_set_parity(config.parity))
goto error;
/* Stop bit */
if (uart_set_stopbit(config.stopbits))
goto error;
/* Number of databits*/
if (uart_set_databits(config.databits))
goto error;
/* No errors in configuration */
return OK;
error:
/* Reset; configuration to 8N1, 9600b */
uart_default_conf();
return ERROR;
}
static void _uart_init (void)
{
tUartControl *pControl;
sam_uart_opt_t config;
int result;
pControl = uart_control[0];
//
pmc_enable_periph_clk (ID_UART);
//
pio_configure (PIOA, PIO_PERIPH_A | PIO_PULLUP, PIO_PA8A_URXD, PIO_DEFAULT);
pio_configure (PIOA, PIO_PERIPH_A, PIO_PA9A_UTXD, PIO_DEFAULT);
//
config.ul_mck = sysclk_get_cpu_hz();
//config.ul_baudrate = BAUD;
config.ul_baudrate = 115200;
config.ul_mode = UART_MR_PAR_NO;
config.ul_chmode = 0;
str_buf_init_std (&pControl->rx_buffer);
str_buf_init_std (&pControl->tx_buffer);
result = uart_init (UART, &config);
uart_reset_tx(UART);
uart_reset_rx(UART);
UART->UART_CR = UART_CR_RSTSTA;
uart_enable_rx(UART);
uart_enable_tx(UART);
uart_enable_interrupt (UART, US_IER_RXRDY);
NVIC_EnableIRQ(UART_IRQn);
}
/**
* \ingroup freertos_uart_peripheral_control_group
* \brief Initializes the FreeRTOS ASF UART driver for the specified UART
* port.
*
* freertos_uart_serial_init() is an ASF specific FreeRTOS driver function. It
* must be called before any other ASF specific FreeRTOS driver functions
* attempt to access the same UART port.
*
* If freertos_driver_parameters->operation_mode equals UART_RS232 then
* freertos_uart_serial_init() will configure the UART port for standard RS232
* operation. If freertos_driver_parameters->operation_mode equals any other
* value then freertos_uart_serial_init() will not take any action.
*
* Other ASF UART functions can be called after freertos_uart_serial_init()
* has completed successfully.
*
* The FreeRTOS ASF driver both installs and handles the UART PDC interrupts.
* Users do not need to concern themselves with interrupt handling, and must
* not install their own interrupt handler.
*
* This driver is provided with an application note, and an example project that
* demonstrates the use of this function.
*
* \param p_uart The UART peripheral being initialized.
* \param uart_parameters Structure that defines the UART bus and transfer
* parameters, such the baud rate and the number of data bits.
* sam_uart_opt_t is a standard ASF type (it is not FreeRTOS specific).
* \param freertos_driver_parameters Defines the driver behavior. See the
* freertos_peripheral_options_t documentation, and the application note that
* accompanies the ASF specific FreeRTOS functions.
*
* \return If the initialization completes successfully then a handle that can
* be used with FreeRTOS UART read and write functions is returned. If
* the initialisation fails then NULL is returned.
*/
freertos_uart_if freertos_uart_serial_init(Uart *p_uart,
const sam_uart_opt_t *const uart_parameters,
const freertos_peripheral_options_t *const freertos_driver_parameters)
{
portBASE_TYPE uart_index;
bool is_valid_operating_mode;
freertos_uart_if return_value;
const enum peripheral_operation_mode valid_operating_modes[] = {UART_RS232};
/* Find the index into the all_uart_definitions array that holds details of
the p_uart peripheral. */
uart_index = get_pdc_peripheral_details(all_uart_definitions,
MAX_UARTS,
(void *) p_uart);
/* Check the requested operating mode is valid for the peripheral. */
is_valid_operating_mode = check_requested_operating_mode(
freertos_driver_parameters->operation_mode,
valid_operating_modes,
sizeof(valid_operating_modes) /
sizeof(enum peripheral_operation_mode));
/* Don't do anything unless a valid p_uart pointer was used, and a valid
operating mode was requested. */
if ((uart_index < MAX_UARTS) && (is_valid_operating_mode == true)) {
/* This function must be called exactly once per supported UART. Check it
has not been called before. */
configASSERT(rx_buffer_definitions[uart_index].next_byte_to_read == NULL);
/* Disable everything before enabling the clock. */
uart_disable_tx(p_uart);
uart_disable_rx(p_uart);
pdc_disable_transfer(all_uart_definitions[uart_index].pdc_base_address,
(PERIPH_PTCR_RXTDIS | PERIPH_PTCR_TXTDIS));
/* Enable the peripheral clock in the PMC. */
pmc_enable_periph_clk(
all_uart_definitions[uart_index].peripheral_id);
switch (freertos_driver_parameters->operation_mode) {
case UART_RS232:
/* Call the standard ASF init function. */
uart_init(p_uart, uart_parameters);
break;
default:
/* Other modes are not currently supported. */
break;
}
/* Disable all the interrupts. */
uart_disable_interrupt(p_uart, MASK_ALL_INTERRUPTS);
/* Create any required peripheral access mutexes and transaction complete
semaphores. This peripheral is full duplex so only the Tx semaphores
are created in the following function. The the Rx semaphores are
created separately. */
create_peripheral_control_semaphores(
freertos_driver_parameters->options_flags,
&(tx_dma_control[uart_index]),
NULL /* The rx structures are not created in this function. */);
/* Is the driver also going to receive? */
if (freertos_driver_parameters->receive_buffer != NULL) {
/* rx_event_semaphore is used to signal the arival of new data. It
must be a counting semaphore for the following reason: If the Rx
DMA places data at the end of its circular buffer it will give the
semaphore to indicate the presence of unread data. If it then
receives more data, it will write this to the start of the circular
buffer, then give the semaphore again. Now, if a task reads data
out of the same circular buffer, and requests less data than is
available, but more than is available between the next read pointer
and the end of the buffer, the actual amount returned will be
capped to that available up to the end of the buffer only. If this
semaphore was a binary semaphore, it would then be 'taken' even
though, unknown to the reading task, unread and therefore available
data remained at the beginning of the buffer. */
rx_buffer_definitions[uart_index].rx_event_semaphore =
xSemaphoreCreateCounting(portMAX_DELAY, 0);
configASSERT(rx_buffer_definitions[uart_index].rx_event_semaphore);
/* The receive buffer is currently empty, so the DMA has control
over the entire buffer. */
rx_buffer_definitions[uart_index].rx_pdc_parameters.ul_addr =
(uint32_t)freertos_driver_parameters->receive_buffer;
rx_buffer_definitions[uart_index].rx_pdc_parameters.ul_size =
freertos_driver_parameters->receive_buffer_size;
pdc_rx_init(
all_uart_definitions[uart_index].pdc_base_address,
&(rx_buffer_definitions[uart_index].rx_pdc_parameters),
NULL);
/* Set the next byte to read to the start of the buffer as no data
has yet been read. */
rx_buffer_definitions[uart_index].next_byte_to_read =
freertos_driver_parameters->receive_buffer;
/* Remember the limits of entire buffer. */
rx_buffer_definitions[uart_index].rx_buffer_start_address =
rx_buffer_definitions[uart_index].rx_pdc_parameters.ul_addr;
rx_buffer_definitions[uart_index].past_rx_buffer_end_address =
rx_buffer_definitions[uart_index].rx_buffer_start_address +
freertos_driver_parameters->receive_buffer_size;
/* If the rx driver is to be thread aware, create an access control
mutex. */
if ((freertos_driver_parameters->options_flags &
USE_RX_ACCESS_MUTEX) != 0) {
rx_buffer_definitions[uart_index].rx_access_mutex =
xSemaphoreCreateMutex();
configASSERT(rx_buffer_definitions[uart_index].rx_access_mutex);
}
/* Catch the DMA running out of Rx space, and gaps in the
reception. These events are both used to signal that there is
data available in the Rx buffer. */
uart_enable_interrupt(p_uart, UART_IER_ENDRX | UART_IER_RXRDY);
/* The Rx DMA is running all the time, so enable it now. */
pdc_enable_transfer(
all_uart_definitions[uart_index].pdc_base_address,
PERIPH_PTCR_RXTEN);
} else {
/* next_byte_to_read is used to check to see if this function
has been called before, so it must be set to something, even if
it is not going to be used. The value it is set to is not
important, provided it is not zero (NULL). */
rx_buffer_definitions[uart_index].next_byte_to_read = RX_NOT_USED;
}
/* Configure and enable the UART interrupt in the interrupt controller. */
configure_interrupt_controller(all_uart_definitions[uart_index].peripheral_irq,
freertos_driver_parameters->interrupt_priority);
/* Error interrupts are always enabled. */
uart_enable_interrupt(
all_uart_definitions[uart_index].peripheral_base_address,
IER_ERROR_INTERRUPTS);
/* Finally, enable the receiver and transmitter. */
uart_enable_tx(p_uart);
uart_enable_rx(p_uart);
return_value = (freertos_uart_if) p_uart;
} else {
return_value = NULL;
}
return return_value;
}
/**
* \brief This function opens an UART
*
* \note Opening of the specified UART implies initializing local variables and
* opening required hardware with the following configuration:
* - bauds as specified
* - 8 bits, no parity, 1 stop bit
* - enable interrupts
*
* \param chn Communication channel [0, 1]
* \param bauds Communication speed in bauds
*
* \retval true on success.
* \retval false on failure.
*/
int8_t buart_if_open(uint8_t chn, uint32_t bauds)
{
#if defined(CONF_BOARD_UART0) || defined(CONF_BOARD_UART1)
sam_uart_opt_t uart_console_settings;
/* MCK for UART */
uart_console_settings.ul_mck = sysclk_get_cpu_hz();
/* Expected baud rate. */
uart_console_settings.ul_baudrate = bauds;
/* Initialize value for UART mode register */
uart_console_settings.ul_mode = UART_MR_PAR_NO;
#else
UNUSED(bauds);
#endif
/* check uart and it is close */
if (chn >= 2) {
return false;
}
if (buart_chn_open[chn]) {
return false;
}
switch (chn) {
#ifdef CONF_BOARD_UART0
case 0:
{
/* Configure PMC. */
pmc_enable_periph_clk(ID_UART0);
/* Configure UART. */
uart_init(UART0, &uart_console_settings);
/* Assign buffers to pointers */
buart_comm_data_0.puc_tq_buf = ptr_tx_uart_buf0;
buart_comm_data_0.puc_rq_buf = ptr_rx_uart_buf0;
buart_comm_data_0.us_rq_count = 0;
buart_comm_data_0.us_rq_idx = 0;
buart_comm_data_0.us_wq_idx = 0;
/* Get board UART0 PDC base address and enable receiver and
* transmitter. */
g_p_uart_pdc0 = uart_get_pdc_base(UART0);
pdc_enable_transfer(g_p_uart_pdc0,
PERIPH_PTCR_RXTEN | PERIPH_PTCR_TXTEN);
/* Start receiving data and start timer. */
g_st_uart_rx_packet0.ul_addr = (uint32_t)gs_puc_uart_buf0;
g_st_uart_rx_packet0.ul_size = UART_BUFFER_SIZE;
pdc_rx_init(g_p_uart_pdc0, &g_st_uart_rx_packet0, NULL);
/* Stop transmitting data */
g_st_uart_tx_packet0.ul_addr = (uint32_t)buart_comm_data_0.puc_tq_buf;
g_st_uart_tx_packet0.ul_size = 0;
pdc_tx_init(g_p_uart_pdc0, &g_st_uart_tx_packet0, NULL);
gs_ul_size_uart_buf0 = UART_BUFFER_SIZE;
/* Transfer to PDC communication mode, disable RXRDY interrupt
* and enable RXBUFF interrupt. */
uart_disable_interrupt(UART0, UART_IDR_RXRDY);
uart_enable_interrupt(UART0, UART_IER_RXBUFF);
/* Enable the receiver and transmitter. */
uart_enable_tx(UART0);
uart_enable_rx(UART0);
/* Configure and enable interrupt of USART. */
NVIC_SetPriority((IRQn_Type)UART0_IRQn, UART0_PRIO);
NVIC_EnableIRQ(UART0_IRQn);
buart_chn_open[chn] = true;
num_bytes_rx_uart0 = 0;
/* Configure TC uart */
_configure_TC_uart();
tc_start(TC_UART, TC_UART_CHN);
return true;
}
break;
#endif
#ifdef CONF_BOARD_UART1
case 1:
{
/* Configure PMC. */
pmc_enable_periph_clk(ID_UART1);
/* Configure UART. */
uart_init(UART1, &uart_console_settings);
/* Assign buffers to pointers */
buart_comm_data_1.puc_tq_buf = ptr_tx_uart_buf1;
buart_comm_data_1.puc_rq_buf = ptr_rx_uart_buf1;
buart_comm_data_1.us_rq_count = 0;
buart_comm_data_1.us_rq_idx = 0;
buart_comm_data_1.us_wq_idx = 0;
/* Get board UART1 PDC base address and enable receiver and
* transmitter. */
g_p_uart_pdc1 = uart_get_pdc_base(UART1);
pdc_enable_transfer(g_p_uart_pdc1,
PERIPH_PTCR_RXTEN | PERIPH_PTCR_TXTEN);
/* Start receiving data and start timer. */
g_st_uart_rx_packet1.ul_addr = (uint32_t)gs_puc_uart_buf1;
g_st_uart_rx_packet1.ul_size = UART_BUFFER_SIZE;
pdc_rx_init(g_p_uart_pdc1, &g_st_uart_rx_packet1, NULL);
/* Stop transmitting data */
g_st_uart_tx_packet1.ul_addr = (uint32_t)buart_comm_data_1.puc_tq_buf;
g_st_uart_tx_packet1.ul_size = 0;
pdc_tx_init(g_p_uart_pdc1, &g_st_uart_tx_packet1, NULL);
gs_ul_size_uart_buf1 = UART_BUFFER_SIZE;
/* Transfer to PDC communication mode, disable RXRDY interrupt
* and enable RXBUFF interrupt. */
uart_disable_interrupt(UART1, UART_IDR_RXRDY);
uart_enable_interrupt(UART1, UART_IER_RXBUFF);
/* Enable the receiver and transmitter. */
uart_enable_tx(UART1);
uart_enable_rx(UART1);
/* Configure and enable interrupt of USART. */
NVIC_SetPriority((IRQn_Type)UART1_IRQn, UART1_PRIO);
NVIC_EnableIRQ(UART1_IRQn);
buart_chn_open[chn] = true;
num_bytes_rx_uart1 = 0;
/* Configure TC uart */
_configure_TC_uart();
tc_start(TC_UART, TC_UART_CHN);
return true;
}
break;
#endif
default:
return false;
}
}
