static int wm831x_buckv_set_voltage(struct regulator_dev *rdev,
int min_uV, int max_uV, unsigned *selector)
{
struct wm831x_dcdc *dcdc = rdev_get_drvdata(rdev);
struct wm831x *wm831x = dcdc->wm831x;
int on_reg = dcdc->base + WM831X_DCDC_ON_CONFIG;
int dvs_reg = dcdc->base + WM831X_DCDC_DVS_CONTROL;
int vsel, ret;
vsel = wm831x_buckv_select_min_voltage(rdev, min_uV, max_uV);
if (vsel < 0)
return vsel;
*selector = vsel;
/* If this value is already set then do a GPIO update if we can */
if (dcdc->dvs_gpio && dcdc->on_vsel == vsel)
return wm831x_buckv_set_dvs(rdev, 0);
if (dcdc->dvs_gpio && dcdc->dvs_vsel == vsel)
return wm831x_buckv_set_dvs(rdev, 1);
/* Always set the ON status to the minimum voltage */
ret = wm831x_set_bits(wm831x, on_reg, WM831X_DC1_ON_VSEL_MASK, vsel);
if (ret < 0)
return ret;
dcdc->on_vsel = vsel;
if (!dcdc->dvs_gpio)
return ret;
/* Kick the voltage transition now */
ret = wm831x_buckv_set_dvs(rdev, 0);
if (ret < 0)
return ret;
/* Set the high voltage as the DVS voltage. This is optimised
* for CPUfreq usage, most processors will keep the maximum
* voltage constant and lower the minimum with the frequency. */
vsel = wm831x_buckv_select_max_voltage(rdev, min_uV, max_uV);
if (vsel < 0) {
/* This should never happen - at worst the same vsel
* should be chosen */
WARN_ON(vsel < 0);
return 0;
}
/* Don't bother if it's the same VSEL we're already using */
if (vsel == dcdc->on_vsel)
return 0;
ret = wm831x_set_bits(wm831x, dvs_reg, WM831X_DC1_DVS_VSEL_MASK, vsel);
if (ret == 0)
dcdc->dvs_vsel = vsel;
else
dev_warn(wm831x->dev, "Failed to set DCDC DVS VSEL: %d\n",
ret);
return 0;
}
static int wm831x_buckv_set_voltage(struct regulator_dev *rdev,
int min_uV, int max_uV, unsigned *selector)
{
struct wm831x_dcdc *dcdc = rdev_get_drvdata(rdev);
struct wm831x *wm831x = dcdc->wm831x;
int on_reg = dcdc->base + WM831X_DCDC_ON_CONFIG;
int dvs_reg = dcdc->base + WM831X_DCDC_DVS_CONTROL;
int vsel, ret;
vsel = wm831x_buckv_select_min_voltage(rdev, min_uV, max_uV);
if (vsel < 0)
return vsel;
*selector = vsel;
/* If this value is already set then do a GPIO update if we can */
if (dcdc->dvs_gpio && dcdc->on_vsel == vsel)
return wm831x_buckv_set_dvs(rdev, 0);
if (dcdc->dvs_gpio && dcdc->dvs_vsel == vsel)
return wm831x_buckv_set_dvs(rdev, 1);
/* Always set the ON status to the minimum voltage */
ret = wm831x_set_bits(wm831x, on_reg, WM831X_DC1_ON_VSEL_MASK, vsel);
if (ret < 0)
return ret;
dcdc->on_vsel = vsel;
if (!dcdc->dvs_gpio)
return ret;
/* Kick the voltage transition now */
ret = wm831x_buckv_set_dvs(rdev, 0);
if (ret < 0)
return ret;
/*
* If this VSEL is higher than the last one we've seen then
* remember it as the DVS VSEL. This is optimised for CPUfreq
* usage where we want to get to the highest voltage very
* quickly.
*/
if (vsel > dcdc->dvs_vsel) {
ret = wm831x_set_bits(wm831x, dvs_reg,
WM831X_DC1_DVS_VSEL_MASK,
dcdc->dvs_vsel);
if (ret == 0)
dcdc->dvs_vsel = vsel;
else
dev_warn(wm831x->dev,
"Failed to set DCDC DVS VSEL: %d\n", ret);
}
return 0;
}
static int wm831x_buckv_set_suspend_voltage(struct regulator_dev *rdev,
int uV)
{
struct wm831x_dcdc *dcdc = rdev_get_drvdata(rdev);
struct wm831x *wm831x = dcdc->wm831x;
u16 reg = dcdc->base + WM831X_DCDC_SLEEP_CONTROL;
int vsel;
vsel = wm831x_buckv_select_min_voltage(rdev, uV, uV);
if (vsel < 0)
return vsel;
return wm831x_set_bits(wm831x, reg, WM831X_DC1_SLP_VSEL_MASK, vsel);
}
