int __init db1300_board_setup(void)
{
unsigned short whoami;
bcsr_init(DB1300_BCSR_PHYS_ADDR,
DB1300_BCSR_PHYS_ADDR + DB1300_BCSR_HEXLED_OFS);
whoami = bcsr_read(BCSR_WHOAMI);
if (BCSR_WHOAMI_BOARD(whoami) != BCSR_WHOAMI_DB1300)
return -ENODEV;
db1300_gpio_config();
printk(KERN_INFO "NetLogic DBAu1300 Development Platform.\n\t"
"BoardID %d CPLD Rev %d DaughtercardID %d\n",
BCSR_WHOAMI_BOARD(whoami), BCSR_WHOAMI_CPLD(whoami),
BCSR_WHOAMI_DCID(whoami));
/* enable UARTs, YAMON only enables #2 */
alchemy_uart_enable(AU1300_UART0_PHYS_ADDR);
alchemy_uart_enable(AU1300_UART1_PHYS_ADDR);
alchemy_uart_enable(AU1300_UART3_PHYS_ADDR);
return 0;
}
static int __init pb1200_init_irq(void)
{
/* We have a problem with CPLD rev 3. */
if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
printk(KERN_ERR "updated to latest revision. This software will\n");
printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
panic("Game over. Your score is 0.");
}
set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
bcsr_init_irq(PB1200_INT_BEGIN, PB1200_INT_END, AU1200_GPIO7_INT);
return 0;
}
void __init board_setup(void)
{
unsigned short whoami;
db1300_gpio_config();
bcsr_init(DB1300_BCSR_PHYS_ADDR,
DB1300_BCSR_PHYS_ADDR + DB1300_BCSR_HEXLED_OFS);
whoami = bcsr_read(BCSR_WHOAMI);
printk(KERN_INFO "NetLogic DBAu1300 Development Platform.\n\t"
"BoardID %d CPLD Rev %d DaughtercardID %d\n",
BCSR_WHOAMI_BOARD(whoami), BCSR_WHOAMI_CPLD(whoami),
BCSR_WHOAMI_DCID(whoami));
alchemy_uart_enable(AU1300_UART0_PHYS_ADDR);
alchemy_uart_enable(AU1300_UART1_PHYS_ADDR);
alchemy_uart_enable(AU1300_UART3_PHYS_ADDR);
}
/* Some peripheral base addresses differ on the PB1200 */
static int __init pb1200_res_fixup(void)
{
/* CPLD Revs earlier than 4 cause problems */
if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "PB1200 must be at CPLD rev 4. Please have\n");
printk(KERN_ERR "the board updated to latest revisions.\n");
printk(KERN_ERR "This software will not work reliably\n");
printk(KERN_ERR "on anything older than CPLD rev 4.!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
return 1;
}
db1200_nand_res[0].start = PB1200_NAND_PHYS_ADDR;
db1200_nand_res[0].end = PB1200_NAND_PHYS_ADDR + 0xff;
db1200_ide_res[0].start = PB1200_IDE_PHYS_ADDR;
db1200_ide_res[0].end = PB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1;
db1200_eth_res[0].start = PB1200_ETH_PHYS_ADDR;
db1200_eth_res[0].end = PB1200_ETH_PHYS_ADDR + 0xff;
return 0;
}
static int __init pb1200_init_irq(void)
{
/* We have a problem with CPLD rev 3. */
if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
printk(KERN_ERR "updated to latest revision. This software will\n");
printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
panic("Game over. Your score is 0.");
}
<<<<<<< HEAD
