/**
* @brief Reads a block of data from the CC2500.
* @param pBuffer : pointer to the buffer that receives the data read from the CC2500.
* @param ReadAddr : CC2500's internal address to read from.
* @param NumByteToRead : number of bytes to read from the CC2500.
* @retval None
*/
void CC2500_Read(uint8_t* pBuffer, uint8_t ReadAddr, uint16_t NumByteToRead)
{
if(NumByteToRead > 0x01)
{
ReadAddr |= (uint8_t)(READWRITE_CMD | MULTIPLEBYTE_CMD);
}
else
{
ReadAddr |= (uint8_t)READWRITE_CMD;
}
/* Set chip select Low at the start of the transmission */
CC2500_CS_LOW();
/* Send the Address of the indexed register */
CC2500_SendByte(ReadAddr);
/* Receive the data that will be read from the device (MSB First) */
while(NumByteToRead > 0x00)
{
/* Send dummy byte (0x00) to generate the SPI clock to CC2500 (Slave device) */
*pBuffer = CC2500_SendByte(DUMMY_BYTE);
NumByteToRead--;
pBuffer++;
}
/* Set chip select High at the end of the transmission */
CC2500_CS_HIGH();
}
/**
* @brief Writes bytes to the CC2500.
* @param pBuffer : pointer to the buffer containing the data to be written to the CC2500.
* @param WriteAddr : CC2500's internal address to write to.
* @param NumByteToWrite: Number of bytes to write.
* @retval None
*/
void CC2500_Write(uint8_t* pBuffer, uint8_t WriteAddr, uint16_t NumByteToWrite) {//Configure the header byte: burst access bit (B) and a 6-bit address (page 21, CC2500)
//If more than one register needs to be written to, set B to 1 (page 23, CC2500)
if(NumByteToWrite > 0x01){
WriteAddr |= BURST_BIT;
}
//Set the Chip Select to low at the beginning of the transmission (page 21, CC2500)
CC2500_CS_LOW();
//Send the address of the register
CC2500_SendByte(WriteAddr);
//Then loop through all of the bytes that need ot be send (MSB first)
while(NumByteToWrite > 0x00){
//Send the current byte at the pBuffer address
CC2500_SendByte(*pBuffer);
//Decrement the number of bytes to write
NumByteToWrite--;
//Increment the pBuffer pointer position
pBuffer++;
}
//Set the Chip Select to high at the end of the transmission (page 23, CC2500)
CC2500_CS_HIGH();
}
/**
* @brief Writes one byte to the CC2500.
* @param pBuffer : pointer to the buffer containing the data to be written to the CC2500.
* @param WriteAddr : CC2500's internal address to write to.
* @param NumByteToWrite: Number of bytes to write.
* @retval None
*/
void CC2500_Write(uint8_t* pBuffer, uint8_t WriteAddr, uint16_t NumByteToWrite)
{
/* Configure the MS bit:
- When 0, the address will remain unchanged in multiple read/write commands.
- When 1, the address will be auto incremented in multiple read/write commands.
*/
if(NumByteToWrite > 0x01)
{
WriteAddr |= (uint8_t)MULTIPLEBYTE_CMD;
}
/* Set chip select Low at the start of the transmission */
CC2500_CS_LOW();
/* Send the Address of the indexed register */
CC2500_SendByte(WriteAddr);
/* Send the data that will be written into the device (MSB First) */
while(NumByteToWrite >= 0x01)
{
CC2500_SendByte(*pBuffer);
NumByteToWrite--;
pBuffer++;
}
/* Set chip select High at the end of the transmission */
CC2500_CS_HIGH();
}
/**
* @brief Writes several byte to the CC2500 registers.
* @param pBuffer : pointer to the buffer containing the data to be written to the CC2500 registers.
* @param WriteAddr : CC2500's internal address to write to.
* @param NumByteToWrite: Number of bytes to write.
* @retval None
*/
void CC2500_WriteRegister(uint8_t* pBuffer, uint8_t WriteAddr, uint16_t NumByteToWrite)
{
//set the first bit of header to 0 (write)
//if multiple bytes to read, set the secodn bit of header to 1 (burst)
if(NumByteToWrite > 0x01)
{
WriteAddr = (uint8_t) ((WriteAddr & CC2500_ADDRESS_MASK) | BURST_MODE);
}
else
{
WriteAddr = (uint8_t) (WriteAddr & CC2500_ADDRESS_MASK);
}
/* Set chip select Low at the start of the transmission */
if (CC2500_Chip_Select() == CC2500_TIMEOUT_ERROR)
{
//terminate the transaction and return
CC2500_CS_HIGH();
return;
}
/* Send the Address of the indexed register */
CC2500_SendByte(WriteAddr);
/* Send the data that will be written into the device (MSB First) */
while(NumByteToWrite >= 0x01)
{
CC2500_SendByte(*pBuffer);
NumByteToWrite--;
pBuffer++;
}
/* Set chip select High at the end of the transmission */
CC2500_CS_HIGH();
}
/**
* @brief Reads a block of data from the CC2500.
* @param pBuffer : pointer to the buffer that receives the data read from the CC2500.
* @param ReadAddr : CC2500's internal address to read from.
* @param NumByteToRead : number of bytes to read from the CC2500.
* @retval None
*/
void CC2500_Read(uint8_t* pBuffer, uint8_t ReadAddr, uint16_t NumByteToRead) {
//Configure the header byte: burst access bit (B) and a 6-bit address (page 21, CC2500)
//If more than one register needs to be written to, set B to 1 (page 23, CC2500)
//Regardless, set the read/write bit
if(NumByteToRead > 0x01){
ReadAddr |= BURST_BIT | READWRITE_BIT;
}
else{
ReadAddr |= READWRITE_BIT;
}
//Set the Chip Select to low at the beginning of the transmission (page 21, CC2500)
CC2500_CS_LOW();
//Send the address of the register
CC2500_SendByte(ReadAddr);
//Then loop through the number of bytes that need to be read (MSB first)
while(NumByteToRead > 0x00){
//Send a dummy byte, store the response in the buffer
*pBuffer = CC2500_SendByte(DUMMY_BYTE);
//Decrement the number of bytes to read
NumByteToRead--;
//Increment the pBuffer pointer position
pBuffer++;
}
//Set the Chip Select to high at the end of the transmission (page 23, CC2500)
CC2500_CS_HIGH();
}
/**
* @brief Writes one CC2500 Command.
* @param WriteCommand : CC2500 Command.
* @param ReadWriteFIFOFlag : 1: return RX FIFO available bytes; 0: return TX FIFO available bytes
* @retval uint8_t status
*/
uint8_t CC2500_WriteCommand(uint8_t WriteCommand, uint8_t ReadWriteFIFOFlag)
{
uint8_t status;
WriteCommand &= (uint8_t) CC2500_ADDRESS_MASK;
if ((WriteCommand < 0x30) || (WriteCommand > 0x3D))
{
return CC2500_STATUS_ERROR;
}
if (ReadWriteFIFOFlag)
{
WriteCommand |= (uint8_t) 0x80;
}
/* Set chip select Low at the start of the transmission */
if (CC2500_Chip_Select() == CC2500_TIMEOUT_ERROR)
{
//terminate the transaction and return
CC2500_CS_HIGH();
return CC2500_STATUS_ERROR;
}
/* Send the Address of the indexed register */
status = CC2500_SendByte(WriteCommand);
/* Set chip select High at the end of the transmission */
CC2500_CS_HIGH();
return status;
}
/**
* @brief Sends a single strobe command to CC2500
* @param Strobe command to send
* @param 1 for the FIFO_BYTES_AVAILABLE field in status byte should be for
the RX FIFO, 0 if it should be for the TX FIFO
* @retval Status update received from CC2500
*/
uint8_t CC2500_Strobe(StrobeCommand StrobeCmd, uint8_t RX_FIFO) {
//Set the Chip Select to low at the beginning of the transmission (page 21, CC2500)
CC2500_CS_LOW();
//The address we'll be writing to
uint8_t StrobeAddr;
//Check which FIFO status should be sent back with the status byte (page 24, CC2500)
if(RX_FIFO){
//Set the read/write bit if we want the RX FIFO
StrobeAddr = ((uint8_t)StrobeCmd) | READWRITE_BIT;
}
else{
//If not, just use the StrobeCmd address
StrobeAddr = (uint8_t)StrobeCmd;
}
//Send the address of the register, get the response
uint8_t statusByte = CC2500_SendByte(StrobeAddr);
//Set the Chip Select to high at the end of the transmission
//only for the SPWD and SXOFF strobes (page 24, CC2500)
if(StrobeCmd == (CC2500_STROBE_SPWD || CC2500_STROBE_SXOFF)){
CC2500_CS_HIGH();
}
//Return the response
return statusByte;
}
/**
* @brief Sends command strobe to the CC2500.
* @param cmd representing command strobe to be issued (see CC2500 UM page 60, table 37).
* @param Pointer to the current state of the CC2500(before strobe was issued).
* @param Pointer to number of free bytes in the CC2500 FIFO(before strobe was issued).
* @retval None
*/
void CC2500_StrobeSend(uint8_t cmd, uint8_t* state, uint8_t* buffer_space)
{
uint8_t chip_status =0;
/* Set chip select Low at the start of the transmission */
CC2500_CS_LOW();
/* Send the command and receive chip ststus byte, and extract the state (bytes 6:4) */
chip_status = CC2500_SendByte(cmd);
/* Set chip select High at the end of the transmission */
CC2500_CS_HIGH();
// osDelay(10);
// CC2500_CS_LOW();
//
// /* Send the command and receive chip ststus byte, and extract the state (bytes 6:4) */
// chip_status = CC2500_SendByte(DUMMY_BYTE);
//
// /* Set chip select High at the end of the transmission */
// CC2500_CS_HIGH();
*state = chip_status & 0x70;
*buffer_space = chip_status & 0x0F;
}
/**
* @brief Reads a block of data from the CC2500.
* @param pBuffer : pointer to the buffer that receives the data read from the CC2500.
* @param ReadAddr : CC2500's internal address to read from.
* @param NumByteToRead : number of bytes to read from the CC2500.
* @retval None
*/
void CC2500_Read(uint8_t* pBuffer, uint8_t ReadAddr, uint16_t NumByteToRead)
{
if(NumByteToRead > 0x01)
{
//differentiate command strobes from status registers using burst mode
//ie. must use burst mode to read status registers however chip will
//only return single register (single byte access for status registers)
//as a result, we check to see if the address is in the status register range,
//if so, keep the burst bit so the chip interprets the right instruction,
//but modify NumByteToRead to only expect single byte return
if((ReadAddr >= 0x30) && (ReadAddr <= 0x3D)){ //address limits for status registers
NumByteToRead = 0x01;
}
//0 is single op, 1 is burst
ReadAddr |= (uint8_t)(READWRITE_CMD | MULTIPLEBYTE_CMD);
}
else
{
ReadAddr |= (uint8_t)READWRITE_CMD;
}
/* Set chip select Low at the start of the transmission */
CC2500_CS_LOW();
/* Send the Address of the indexed register */
*pBuffer = CC2500_SendByte(ReadAddr);
/* Receive the data that will be read from the device (MSB First) */
while(NumByteToRead > 0x00)
{
/* Send dummy byte (0x00) to generate the SPI clock to LIS302DL (Slave device) */
*pBuffer = CC2500_SendByte(DUMMY_BYTE);
NumByteToRead--;
pBuffer++;
}
/* Set chip select High at the end of the transmission */
CC2500_CS_HIGH();
}
/**
* @brief Reads a block of data from the CC2500 registers.
* @param pBuffer : pointer to the buffer that receives the data read from the CC2500.
* @param ReadAddr : CC2500's internal address to read from.
* @param NumByteToRead : number of bytes to read from the CC2500 registers.
* @retval None
*/
void CC2500_ReadRegister(uint8_t* pBuffer, uint8_t ReadAddr, uint16_t NumByteToRead)
{
ReadAddr = (uint8_t) (ReadAddr & CC2500_ADDRESS_MASK);
//set the first bit of header to 1 (read)
//if multiple bytes to read or read status registers, set the second bit of header to 1 (burst)
if((NumByteToRead > 0x01) || ((ReadAddr >= 0x30) && (ReadAddr <=0x3D)))
{
ReadAddr |= (uint8_t) (READ_MODE | BURST_MODE);
}
else
{
ReadAddr |= (uint8_t) READ_MODE;
}
/* Set chip select Low at the start of the transmission */
if (CC2500_Chip_Select() == CC2500_TIMEOUT_ERROR)
{
//terminate the transaction and return
CC2500_CS_HIGH();
return;
}
/* Send the Address of the indexed register */
CC2500_SendByte(ReadAddr);
/* Receive the data that will be read from the device (MSB First) */
while(NumByteToRead > 0x00)
{
/* Send dummy byte (0x00) to generate the SPI clock to LIS302DL (Slave device) */
*pBuffer = CC2500_SendByte(DUMMY_BYTE);
NumByteToRead--;
pBuffer++;
}
/* Set chip select High at the end of the transmission */
CC2500_CS_HIGH();
}