void stop_edma_loop_putsem(void *parameter, edma_chn_status_t status)
{
/* Stop eDMA channel transfers. */
EDMA_DRV_StopChannel((edma_chn_state_t *)parameter);
/* Increase semaphore to indicate an eDMA channel has completed transfer. */
mico_rtos_set_semaphore( &spi_transfer_finished_semaphore );
}
void stop_rx_edma(void *parameter, edma_chn_status_t status)
{
spi_dma_sem = 1;
/* Stop eDMA channel transfers. */
EDMA_DRV_StopChannel((edma_chn_state_t *)parameter);
}
void stop_edma_loop(void *parameter, edma_chn_status_t status)
{
/* Increase semaphore to indicate an eDMA channel has completed transfer. */
OSA_SemaPost(&g_statusSem);
/* Stop eDMA channel transfers. */
EDMA_DRV_StopChannel((edma_chn_state_t *)parameter);
}
void disable_edma_loop(edma_loop_setup_t *loopSetup)
{
EDMA_DRV_StopChannel(loopSetup->dmaCh);
#if (defined(__ICCARM__) || defined(__CC_ARM))
free_align(loopSetup->dmaChStcd);
#elif defined(__GNUC__)
//OSA_MemFree(loopSetup->dmaChStcd);
#endif
print_edma_ch_erq(DMA0, loopSetup->dmaChanNum);
//OSA_MemFree(loopSetup);
}
/*FUNCTION*********************************************************************
*
* Function Name : FLEXIO_Camera_DRV_ResetEdmaRx
* Description : Reset the EDMA transfer loop's destination address and loop
* counter, which means the EDMA transfer would be reset to the initialized state.
* This API would be called when VSYNC event happenned to make sure the data
* from camera would not be misplaced. However, if there is other application
* configuration can do the same thing, this API would not be necessary.
*
*END*************************************************************************/
flexio_camera_status_t FLEXIO_Camera_DRV_ResetEdmaRx(
flexio_camera_edma_handler_t *handler)
{
uint32_t ret;
edma_transfer_config_t rxEdmeConfigStruct;
edma_software_tcd_t rxEdmaChnStcd[2];
flexio_camera_dev_t *flexioCameraHwConfigPtr = &(handler->flexioCameraHwConfig);
EDMA_DRV_StopChannel(&handler->rxEdmaChnState);
/* 3. Configure the channel. */
rxEdmeConfigStruct.srcAddr = FLEXIO_Camera_HAL_GetRxBufferAddr(flexioCameraHwConfigPtr);
rxEdmeConfigStruct.destAddr = handler->userBufAddr;
rxEdmeConfigStruct.srcTransferSize = kEDMATransferSize_32Bytes;
rxEdmeConfigStruct.destTransferSize = kEDMATransferSize_32Bytes;
rxEdmeConfigStruct.srcOffset = 0;
rxEdmeConfigStruct.destOffset = 4U * (flexioCameraHwConfigPtr->shifterCount); /* 4 byte per shifter, typically 32 byte for 8 shifters. */
rxEdmeConfigStruct.srcLastAddrAdjust = 0;
rxEdmeConfigStruct.destLastAddrAdjust = -(int32_t)(handler->userBufLenByte);
rxEdmeConfigStruct.srcModulo = kEDMAModuloDisable;
rxEdmeConfigStruct.destModulo = kEDMAModuloDisable;
rxEdmeConfigStruct.minorLoopCount = rxEdmeConfigStruct.destOffset; /* the minor loop would read all the data in shifters one time per trigger. */
rxEdmeConfigStruct.majorLoopCount = (handler->userBufLenByte)/(rxEdmeConfigStruct.minorLoopCount);
ret = EDMA_DRV_PrepareDescriptorTransfer(
&handler->rxEdmaChnState,
rxEdmaChnStcd,
&rxEdmeConfigStruct,
false, /* Always disable transfer done interrupt. */
false /* Always disable auto shutdown req. */
);
if (ret == kEDMAInvalidChannel)
{
return kStatus_FlexIO_Camera_Failed;
}
ret = EDMA_DRV_PushDescriptorToReg( &handler->rxEdmaChnState, rxEdmaChnStcd);
if (ret == kEDMAInvalidChannel)
{
return kStatus_FlexIO_Camera_Failed;
}
EDMA_DRV_StartChannel(&handler->rxEdmaChnState);
return kStatus_FlexIO_Camera_Success;
}
/*FUNCTION**********************************************************************
*
* Function Name : UART_DRV_EdmaCompleteReceiveData
* Description : Finish up a receive by completing the process of receiving data
* and disabling the interrupt.
* This is not a public API as it is called from other driver functions.
*
*END**************************************************************************/
static void UART_DRV_EdmaCompleteReceiveData(uint32_t instance)
{
assert(instance < UART_INSTANCE_COUNT);
uart_edma_state_t * uartEdmaState = (uart_edma_state_t *)g_uartStatePtr[instance];
/* Stop DMA channel. */
EDMA_DRV_StopChannel(&uartEdmaState->edmaUartRx);
/* Signal the synchronous completion object. */
if (uartEdmaState->isRxBlocking)
{
OSA_SemaPost(&uartEdmaState->rxIrqSync);
}
/* Update the information of the module driver state */
uartEdmaState->isRxBusy = false;
}
/*FUNCTION**********************************************************************
*
* Function Name : LPUART_DRV_EdmaCompleteSendData
* Description : Finish up a transmit by completing the process of sending
* data and disabling the interrupt.
* This is not a public API as it is called from other driver functions.
*
*END**************************************************************************/
static void LPUART_DRV_EdmaCompleteSendData(uint32_t instance)
{
assert(instance < LPUART_INSTANCE_COUNT);
lpuart_edma_state_t * lpuartEdmaState = (lpuart_edma_state_t *)g_lpuartStatePtr[instance];
/* Stop DMA channel. */
EDMA_DRV_StopChannel(&lpuartEdmaState->edmaLpuartTx);
/* Signal the synchronous completion object. */
if (lpuartEdmaState->isTxBlocking)
{
OSA_SemaPost(&lpuartEdmaState->txIrqSync);
}
/* Update the information of the module driver state */
lpuartEdmaState->isTxBusy = false;
}
/*FUNCTION*********************************************************************
*
* Function Name : SND_RxDeinit
* Description : Deinit the rx soundcard.
* The soundcard includes a controller and a codec.
*END**************************************************************************/
snd_status_t SND_RxDeinit(sound_card_t *card)
{
audio_controller_t *ctrl = &card->controller;
audio_codec_t *codec = &card->codec;
audio_buffer_t *buffer = &card->buffer;
/* Call the deinit function of the ctrl and codec. */
ctrl->ops->Ctrl_RxDeinit(ctrl->instance);
codec->ops->Codec_Deinit((void *)codec->handler);
#if USEDMA
/* Deinit the dma resource */
EDMA_DRV_StopChannel(&ctrl->dma_channel);
EDMA_DRV_ReleaseChannel(&ctrl->dma_channel);
#endif
OSA_SemaDestroy(&buffer->sem);
#if !SOUNDCARD_USE_STATIC_MEM
/* Free the tx and rx buffer. */
OSA_MemFree(buffer->buff);
#endif
return kStatus_SND_Success;
}
/*FUNCTION**********************************************************************
*
* Function Name : UART_DRV_EdmaSendDataBlocking
* Description : Sends (transmits) data out through the UART-DMA module
* using a blocking method.
*
*END**************************************************************************/
uart_status_t UART_DRV_EdmaSendDataBlocking(uint32_t instance,
const uint8_t * txBuff,
uint32_t txSize,
uint32_t timeout)
{
assert(txBuff);
assert(instance < UART_INSTANCE_COUNT);
uart_edma_state_t * uartEdmaState = (uart_edma_state_t *)g_uartStatePtr[instance];
uart_status_t retVal = kStatus_UART_Success;
osa_status_t syncStatus;
/* Indicates current transaction is blocking. */
uartEdmaState->isTxBlocking = true;
/* Start the transmission process */
retVal = UART_DRV_EdmaStartSendData(instance, txBuff, txSize);
if (retVal == kStatus_UART_Success)
{
/* Wait until the transmit is complete. */
do
{
syncStatus = OSA_SemaWait(&uartEdmaState->txIrqSync, timeout);
}while(syncStatus == kStatus_OSA_Idle);
if (syncStatus != kStatus_OSA_Success)
{
/* Stop DMA channel. */
EDMA_DRV_StopChannel(&uartEdmaState->edmaUartTx);
/* Update the information of the module driver state */
uartEdmaState->isTxBusy = false;
retVal = kStatus_UART_Timeout;
}
}
return retVal;
}
/*FUNCTION**********************************************************************
*
* Function Name : UART_DRV_EdmaReceiveDataBlocking
* Description : This function gets (receives) data from the UART module using
* a blocking method. A blocking (also known as synchronous) function means that
* the function does not return until the receive is complete. This blocking
* function is used to send data through the UART port.
*
*END**************************************************************************/
uart_status_t UART_DRV_EdmaReceiveDataBlocking(uint32_t instance,
uint8_t * rxBuff,
uint32_t rxSize,
uint32_t timeout)
{
assert(rxBuff);
assert(instance < UART_INSTANCE_COUNT);
uart_edma_state_t * uartEdmaState = (uart_edma_state_t *)g_uartStatePtr[instance];
uart_status_t retVal = kStatus_UART_Success;
osa_status_t syncStatus;
/* Indicates current transaction is blocking. */
uartEdmaState->isRxBlocking = true;
retVal = UART_DRV_EdmaStartReceiveData(instance, rxBuff, rxSize);
if (retVal == kStatus_UART_Success)
{
/* Wait until all the data is received or for timeout.*/
do
{
syncStatus = OSA_SemaWait(&uartEdmaState->rxIrqSync, timeout);
}while(syncStatus == kStatus_OSA_Idle);
if (syncStatus != kStatus_OSA_Success)
{
/* Stop DMA channel. */
EDMA_DRV_StopChannel(&uartEdmaState->edmaUartRx);
/* Update the information of the module driver state */
uartEdmaState->isRxBusy = false;
retVal = kStatus_UART_Timeout;
}
}
return retVal;
}
/*FUNCTION**********************************************************************
*
* Function Name : QSPI_DRV_RxEdmaCallback
* Description : EDMA callback function for QSPI rx, this will be called while
* QSPI finished the reading.
*
*END**************************************************************************/
void QSPI_DRV_RxEdmaCallback(void *param, edma_chn_status_t status)
{
qspi_state_t *state = (qspi_state_t *)param;
EDMA_DRV_StopChannel(&state->rxEdmaChn);
state->isRxBusy = false;
}
void stop_edma_loop(void *parameter, edma_chn_status_t status)
{
/* Stop eDMA channel transfers. */
EDMA_DRV_StopChannel((edma_chn_state_t *)parameter);
}
void disable_edma_loop(edma_loop_setup_t *loopSetup)
{
EDMA_DRV_StopChannel(loopSetup->dmaCh);
}
