/**********************************************************************//** * @brief Initializes the System * * @param none * * @return none *************************************************************************/ void SystemInit(void) { // Set the DCO to 8MHz (it's also the device's power-on setting). Do not change this frequency! // It impacts the cap touch scan window. CS_setDCOFreq(__MSP430_BASEADDRESS_CS__, CS_DCORSEL_0, CS_DCOFSEL_6); // Configure clock source and clock dividers. After this the clock configuration will be as follows: // ACLK=LFXT1/1=32,768Hz; SMCLK=DCOCLK/1=8MHz; and MCLK=DCOCLK/1=8MHz. CS_clockSignalInit(__MSP430_BASEADDRESS_CS__, CS_ACLK, CS_LFXTCLK_SELECT, CS_CLOCK_DIVIDER_1); CS_clockSignalInit(__MSP430_BASEADDRESS_CS__, CS_SMCLK, CS_DCOCLK_SELECT, CS_CLOCK_DIVIDER_1); CS_clockSignalInit(__MSP430_BASEADDRESS_CS__, CS_MCLK, CS_DCOCLK_SELECT, CS_CLOCK_DIVIDER_1); // Set all GPIO to output low to minimize current draw by eliminating floating pins. GPIO_setOutputLowOnPin(GPIO_PORT_PA, GPIO_PIN0 | GPIO_PIN1 | GPIO_PIN2 | GPIO_PIN3 | GPIO_PIN4 | GPIO_PIN5 | GPIO_PIN6 | GPIO_PIN7 | GPIO_PIN8 | GPIO_PIN9 | GPIO_PIN10 | GPIO_PIN11 | GPIO_PIN12 | GPIO_PIN13 | GPIO_PIN14 | GPIO_PIN15); GPIO_setOutputLowOnPin(GPIO_PORT_PB, GPIO_PIN0 | GPIO_PIN1 | GPIO_PIN2 | GPIO_PIN3 | GPIO_PIN4 | GPIO_PIN5 | GPIO_PIN6 | GPIO_PIN7 | GPIO_PIN8 | GPIO_PIN9 | GPIO_PIN10 | GPIO_PIN11 | GPIO_PIN12 | GPIO_PIN13 | GPIO_PIN14 | GPIO_PIN15); GPIO_setOutputLowOnPin(GPIO_PORT_PJ, GPIO_PIN0 | GPIO_PIN1 | GPIO_PIN2 | GPIO_PIN3 | GPIO_PIN6 | GPIO_PIN7 | GPIO_PIN8 | GPIO_PIN9 | GPIO_PIN10 | GPIO_PIN11 | GPIO_PIN12 | GPIO_PIN13 | GPIO_PIN14 | GPIO_PIN15); GPIO_setAsOutputPin(GPIO_PORT_PA, GPIO_PIN0 | GPIO_PIN1 | GPIO_PIN2 | GPIO_PIN3 | GPIO_PIN4 | GPIO_PIN5 | GPIO_PIN6 | GPIO_PIN7 | GPIO_PIN8 | GPIO_PIN9 | GPIO_PIN10 | GPIO_PIN11 | GPIO_PIN12 | GPIO_PIN13 | GPIO_PIN14 | GPIO_PIN15); GPIO_setAsOutputPin(GPIO_PORT_PB, GPIO_PIN0 | GPIO_PIN1 | GPIO_PIN2 | GPIO_PIN3 | GPIO_PIN4 | GPIO_PIN5 | GPIO_PIN6 | GPIO_PIN7 | GPIO_PIN8 | GPIO_PIN9 | GPIO_PIN10 | GPIO_PIN11 | GPIO_PIN12 | GPIO_PIN13 | GPIO_PIN14 | GPIO_PIN15); GPIO_setAsOutputPin(GPIO_PORT_PJ, GPIO_PIN0 | GPIO_PIN1 | GPIO_PIN2 | GPIO_PIN3 | GPIO_PIN6 | GPIO_PIN7 | GPIO_PIN8 | GPIO_PIN9 | GPIO_PIN10 | GPIO_PIN11 | GPIO_PIN12 | GPIO_PIN13 | GPIO_PIN14 | GPIO_PIN15); // Configure the left button (S2) connected to P4.6. For this enable the internal pull-up resistor and // setup the pin interrupt to trigger on rising edges. GPIO_setAsInputPinWithPullUpresistor(GPIO_PORT_P4, GPIO_PIN5); GPIO_interruptEdgeSelect(GPIO_PORT_P4, GPIO_PIN5, GPIO_LOW_TO_HIGH_TRANSITION); GPIO_clearInterruptFlag(GPIO_PORT_P4, GPIO_PIN5); GPIO_enableInterrupt(GPIO_PORT_P4, GPIO_PIN5); // Configure the right button (S3) connected to P1.1. For this enable the internal pull-up resistor and // setup the pin interrupt to trigger on rising edges. GPIO_setAsInputPinWithPullUpresistor(GPIO_PORT_P1, GPIO_PIN1); GPIO_interruptEdgeSelect(GPIO_PORT_P1, GPIO_PIN1, GPIO_LOW_TO_HIGH_TRANSITION); GPIO_clearInterruptFlag(GPIO_PORT_P1, GPIO_PIN1); GPIO_enableInterrupt(GPIO_PORT_P1, GPIO_PIN1); // CapSense Setup. GPIO pins P1.3-1.5 and P3.4-3.6 are used for capacitive touch so let's // switch them to inputs. // GPIO_setAsInputPin(GPIO_PORT_P1, GPIO_PIN3 | GPIO_PIN4 | GPIO_PIN5); GPIO_setAsInputPin(GPIO_PORT_P3, GPIO_PIN4 | GPIO_PIN5 | GPIO_PIN6); // Enable LFXT functionality on PJ.4 and PJ.5. For this we only need to configure PJ.4 to // LFXIN and the port module logic takes care of the rest. GPIO_setAsPeripheralModuleFunctionInputPin(GPIO_PORT_PJ, GPIO_PIN4, GPIO_PRIMARY_MODULE_FUNCTION); // Disable the GPIO power-on default high-impedance mode to activate previously configured port settings PMM_unlockLPM5(__MSP430_BASEADDRESS_PMM_FRAM__); // Perform the required LFXT startup procedure now that all of the port pins are configured. CS_setExternalClockSource(__MSP430_BASEADDRESS_CS__, 32768, 0); CS_LFXTStart(__MSP430_BASEADDRESS_CS__, CS_LFXT_DRIVE0); // Initialize LCD driver and the context for the LCD Sharp96x96_LCDInit(); TA0_enableVCOMToggle(); GrContextInit(&sContext, &g_sharp96x96LCD); GrContextForegroundSet(&sContext, ClrBlack); GrContextBackgroundSet(&sContext, ClrWhite); onLED(); //blink LED1 }
void button_clear_interrupt_flag() { GPIO_clearInterruptFlag(INPUT1_BASEADDRESS, INPUT1_PORT, INPUT1_PIN); GPIO_clearInterruptFlag(INPUT2_BASEADDRESS, INPUT2_PORT, INPUT2_PIN); GPIO_clearInterruptFlag(INPUT3_BASEADDRESS, INPUT3_PORT, INPUT3_PIN); }
void Port2_Pin5_6_Init(){ //Enable Pin internal resistance as pull-Up resistance GPIO_setAsInputPinWithPullUpresistor( GPIO_PORT_P2, GPIO_PIN4 ); //Pin IFG cleared GPIO_clearInterruptFlag( GPIO_PORT_P2, GPIO_PIN4 ); //Pin interrupt enabled GPIO_enableInterrupt( GPIO_PORT_P2, GPIO_PIN4 ); //Pin Hi/Lo edge GPIO_interruptEdgeSelect( GPIO_PORT_P2, GPIO_PIN4, GPIO_HIGH_TO_LOW_TRANSITION ); }
__interrupt void Port_2 (void) { __delay_cycles(10000); //1234us at 8MHz if (GPIO_INPUT_PIN_LOW == GPIO_getInputPinValue(GPIO_PORT_P2,GPIO_PIN4)){ __delay_cycles(10); }else{ __delay_cycles(10); } //Pin IFG cleared GPIO_clearInterruptFlag( GPIO_PORT_P2, GPIO_PIN4 ); }
void buttonInit(void){ GPIO_setCallback(Board_BUTTON0, gpioButton0); GPIO_enableInt(Board_BUTTON0); /* Configure RGB LED pins */ GPIO_setAsOutputPin(GPIO_PORT_P2, GPIO_PIN4 | GPIO_PIN6); GPIO_setAsOutputPin(GPIO_PORT_P5, GPIO_PIN6); /* Set RGB LED to red */ P2OUT |= BIT6; P2OUT &= ~BIT4; P5OUT &= ~BIT6; /* Setup Button */ GPIO_setAsInputPinWithPullUpResistor(GPIO_PORT_P5,GPIO_PIN1); GPIO_clearInterruptFlag(GPIO_PORT_P5, GPIO_PIN1); GPIO_enableInterrupt(GPIO_PORT_P5, GPIO_PIN1); GPIO_interruptEdgeSelect(GPIO_PORT_P5, GPIO_PIN1, GPIO_HIGH_TO_LOW_TRANSITION); Interrupt_enableInterrupt(INT_PORT5); }
/**********************************************************************//** * @brief Enables Right Switch * * @param none * * @return none *************************************************************************/ void EnableRightSwitch(void) { GPIO_clearInterruptFlag(GPIO_PORT_P1, GPIO_PIN1); GPIO_enableInterrupt(GPIO_PORT_P1, GPIO_PIN1); }
/**********************************************************************//** * @brief Enables Left Switch * * @param none * * @return none *************************************************************************/ void EnableLeftSwitch(void) { GPIO_clearInterruptFlag(GPIO_PORT_P4, GPIO_PIN5); GPIO_enableInterrupt(GPIO_PORT_P4, GPIO_PIN5); }
void PORT1_IRQHandler(void) { uint32_t status = GPIO_getEnabledInterruptStatus(GPIO_PORT_P1); GPIO_clearInterruptFlag(GPIO_PORT_P1, status); }