bool ath9k_hw_init_cal(struct ath_hal *ah,
struct ath9k_channel *chan)
{
struct ath_hal_5416 *ahp = AH5416(ah);
struct ath9k_channel *ichan = ath9k_regd_check_channel(ah, chan);
REG_WRITE(ah, AR_PHY_AGC_CONTROL,
REG_READ(ah, AR_PHY_AGC_CONTROL) |
AR_PHY_AGC_CONTROL_CAL);
if (!ath9k_hw_wait(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL, 0)) {
DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
"offset calibration failed to complete in 1ms; "
"noisy environment?\n");
return false;
}
if (AR_SREV_9285(ah) && AR_SREV_9285_11_OR_LATER(ah))
ath9k_hw_9285_pa_cal(ah);
REG_WRITE(ah, AR_PHY_AGC_CONTROL,
REG_READ(ah, AR_PHY_AGC_CONTROL) |
AR_PHY_AGC_CONTROL_NF);
ahp->ah_cal_list = ahp->ah_cal_list_last = ahp->ah_cal_list_curr = NULL;
if (AR_SREV_9100(ah) || AR_SREV_9160_10_OR_LATER(ah)) {
if (ath9k_hw_iscal_supported(ah, chan, ADC_GAIN_CAL)) {
INIT_CAL(&ahp->ah_adcGainCalData);
INSERT_CAL(ahp, &ahp->ah_adcGainCalData);
DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
"enabling ADC Gain Calibration.\n");
}
if (ath9k_hw_iscal_supported(ah, chan, ADC_DC_CAL)) {
INIT_CAL(&ahp->ah_adcDcCalData);
INSERT_CAL(ahp, &ahp->ah_adcDcCalData);
DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
"enabling ADC DC Calibration.\n");
}
if (ath9k_hw_iscal_supported(ah, chan, IQ_MISMATCH_CAL)) {
INIT_CAL(&ahp->ah_iqCalData);
INSERT_CAL(ahp, &ahp->ah_iqCalData);
DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
"enabling IQ Calibration.\n");
}
ahp->ah_cal_list_curr = ahp->ah_cal_list;
if (ahp->ah_cal_list_curr)
ath9k_hw_reset_calibration(ah, ahp->ah_cal_list_curr);
}
ichan->CalValid = 0;
return true;
}
HAL_BOOL
ar5416InitCal(struct ath_hal *ah, const struct ieee80211_channel *chan)
{
struct ar5416PerCal *cal = &AH5416(ah)->ah_cal;
HAL_CHANNEL_INTERNAL *ichan;
ichan = ath_hal_checkchannel(ah, chan);
HALASSERT(ichan != AH_NULL);
/* Do initial chipset-specific calibration */
if (! AH5416(ah)->ah_cal_initcal(ah, chan)) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: initial chipset calibration did "
"not complete in time; noisy environment?\n", __func__);
return AH_FALSE;
}
/* If there's PA Cal, do it */
if (AH5416(ah)->ah_cal_pacal)
AH5416(ah)->ah_cal_pacal(ah, AH_TRUE);
/*
* Do NF calibration after DC offset and other CALs.
* Per system engineers, noise floor value can sometimes be 20 dB
* higher than normal value if DC offset and noise floor cal are
* triggered at the same time.
*/
OS_REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);
/*
* This may take a while to run; make sure subsequent
* calibration routines check that this has completed
* before reading the value and triggering a subsequent
* calibration.
*/
/* Initialize list pointers */
cal->cal_list = cal->cal_last = cal->cal_curr = AH_NULL;
/*
* Enable IQ, ADC Gain, ADC DC Offset Cals
*/
if (AR_SREV_HOWL(ah) || AR_SREV_SOWL_10_OR_LATER(ah)) {
/* Setup all non-periodic, init time only calibrations */
/* XXX: Init DC Offset not working yet */
#if 0
if (ar5416IsCalSupp(ah, chan, ADC_DC_INIT_CAL)) {
INIT_CAL(&cal->adcDcCalInitData);
INSERT_CAL(cal, &cal->adcDcCalInitData);
}
/* Initialize current pointer to first element in list */
cal->cal_curr = cal->cal_list;
if (cal->ah_cal_curr != AH_NULL && !ar5416RunInitCals(ah, 0))
return AH_FALSE;
#endif
}
/* If Cals are supported, add them to list via INIT/INSERT_CAL */
if (ar5416IsCalSupp(ah, chan, ADC_GAIN_CAL)) {
INIT_CAL(&cal->adcGainCalData);
INSERT_CAL(cal, &cal->adcGainCalData);
HALDEBUG(ah, HAL_DEBUG_PERCAL,
"%s: enable ADC Gain Calibration.\n", __func__);
}
if (ar5416IsCalSupp(ah, chan, ADC_DC_CAL)) {
INIT_CAL(&cal->adcDcCalData);
INSERT_CAL(cal, &cal->adcDcCalData);
HALDEBUG(ah, HAL_DEBUG_PERCAL,
"%s: enable ADC DC Calibration.\n", __func__);
}
if (ar5416IsCalSupp(ah, chan, IQ_MISMATCH_CAL)) {
INIT_CAL(&cal->iqCalData);
INSERT_CAL(cal, &cal->iqCalData);
HALDEBUG(ah, HAL_DEBUG_PERCAL,
"%s: enable IQ Calibration.\n", __func__);
}
/* Initialize current pointer to first element in list */
cal->cal_curr = cal->cal_list;
/* Kick off measurements for the first cal */
if (cal->cal_curr != AH_NULL)
ar5416ResetMeasurement(ah, cal->cal_curr);
/* Mark all calibrations on this channel as being invalid */
ichan->calValid = 0;
return AH_TRUE;
#undef MAX_CAL_CHECK
}
/*
* Initialize Calibration infrastructure.
*/
HAL_BOOL
ar5416InitCal(struct ath_hal *ah, const struct ieee80211_channel *chan)
{
struct ar5416PerCal *cal = &AH5416(ah)->ah_cal;
HAL_CHANNEL_INTERNAL *ichan;
ichan = ath_hal_checkchannel(ah, chan);
HALASSERT(ichan != AH_NULL);
if (AR_SREV_MERLIN_10_OR_LATER(ah)) {
/* Enable Rx Filter Cal */
OS_REG_CLR_BIT(ah, AR_PHY_ADC_CTL, AR_PHY_ADC_CTL_OFF_PWDADC);
OS_REG_SET_BIT(ah, AR_PHY_AGC_CONTROL,
AR_PHY_AGC_CONTROL_FLTR_CAL);
/* Clear the carrier leak cal bit */
OS_REG_CLR_BIT(ah, AR_PHY_CL_CAL_CTL, AR_PHY_CL_CAL_ENABLE);
/* kick off the cal */
OS_REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL);
/* Poll for offset calibration complete */
if (!ath_hal_wait(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL, 0)) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: offset calibration failed to complete in 1ms; "
"noisy environment?\n", __func__);
return AH_FALSE;
}
/* Set the cl cal bit and rerun the cal a 2nd time */
/* Enable Rx Filter Cal */
OS_REG_CLR_BIT(ah, AR_PHY_ADC_CTL, AR_PHY_ADC_CTL_OFF_PWDADC);
OS_REG_SET_BIT(ah, AR_PHY_AGC_CONTROL,
AR_PHY_AGC_CONTROL_FLTR_CAL);
OS_REG_SET_BIT(ah, AR_PHY_CL_CAL_CTL, AR_PHY_CL_CAL_ENABLE);
}
/* Calibrate the AGC */
OS_REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL);
/* Poll for offset calibration complete */
if (!ath_hal_wait(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL, 0)) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: offset calibration did not complete in 1ms; "
"noisy environment?\n", __func__);
return AH_FALSE;
}
/*
* Do NF calibration after DC offset and other CALs.
* Per system engineers, noise floor value can sometimes be 20 dB
* higher than normal value if DC offset and noise floor cal are
* triggered at the same time.
*/
OS_REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);
/* Initialize list pointers */
cal->cal_list = cal->cal_last = cal->cal_curr = AH_NULL;
/*
* Enable IQ, ADC Gain, ADC DC Offset Cals
*/
if (AR_SREV_SOWL_10_OR_LATER(ah)) {
/* Setup all non-periodic, init time only calibrations */
/* XXX: Init DC Offset not working yet */
#if 0
if (ar5416IsCalSupp(ah, chan, ADC_DC_INIT_CAL)) {
INIT_CAL(&cal->adcDcCalInitData);
INSERT_CAL(cal, &cal->adcDcCalInitData);
}
/* Initialize current pointer to first element in list */
cal->cal_curr = cal->cal_list;
if (cal->ah_cal_curr != AH_NULL && !ar5416RunInitCals(ah, 0))
return AH_FALSE;
#endif
}
/* If Cals are supported, add them to list via INIT/INSERT_CAL */
if (ar5416IsCalSupp(ah, chan, ADC_GAIN_CAL)) {
INIT_CAL(&cal->adcGainCalData);
INSERT_CAL(cal, &cal->adcGainCalData);
HALDEBUG(ah, HAL_DEBUG_PERCAL,
"%s: enable ADC Gain Calibration.\n", __func__);
}
if (ar5416IsCalSupp(ah, chan, ADC_DC_CAL)) {
INIT_CAL(&cal->adcDcCalData);
INSERT_CAL(cal, &cal->adcDcCalData);
HALDEBUG(ah, HAL_DEBUG_PERCAL,
"%s: enable ADC DC Calibration.\n", __func__);
}
if (ar5416IsCalSupp(ah, chan, IQ_MISMATCH_CAL)) {
INIT_CAL(&cal->iqCalData);
INSERT_CAL(cal, &cal->iqCalData);
HALDEBUG(ah, HAL_DEBUG_PERCAL,
"%s: enable IQ Calibration.\n", __func__);
}
/* Initialize current pointer to first element in list */
cal->cal_curr = cal->cal_list;
/* Kick off measurements for the first cal */
if (cal->cal_curr != AH_NULL)
ar5416ResetMeasurement(ah, cal->cal_curr);
/* Mark all calibrations on this channel as being invalid */
ichan->calValid = 0;
return AH_TRUE;
}
bool ath9k_hw_init_cal(struct ath_hw *ah, struct ath9k_channel *chan)
{
if (AR_SREV_9285_12_OR_LATER(ah)) {
if (!ar9285_clc(ah, chan))
return false;
} else {
if (AR_SREV_9280_10_OR_LATER(ah)) {
if (!AR_SREV_9287_10_OR_LATER(ah))
REG_CLR_BIT(ah, AR_PHY_ADC_CTL,
AR_PHY_ADC_CTL_OFF_PWDADC);
REG_SET_BIT(ah, AR_PHY_AGC_CONTROL,
AR_PHY_AGC_CONTROL_FLTR_CAL);
}
/* Calibrate the AGC */
REG_WRITE(ah, AR_PHY_AGC_CONTROL,
REG_READ(ah, AR_PHY_AGC_CONTROL) |
AR_PHY_AGC_CONTROL_CAL);
/* Poll for offset calibration complete */
if (!ath9k_hw_wait(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL,
0, AH_WAIT_TIMEOUT)) {
DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
"offset calibration failed to complete in 1ms; "
"noisy environment?\n");
return false;
}
if (AR_SREV_9280_10_OR_LATER(ah)) {
if (!AR_SREV_9287_10_OR_LATER(ah))
REG_SET_BIT(ah, AR_PHY_ADC_CTL,
AR_PHY_ADC_CTL_OFF_PWDADC);
REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL,
AR_PHY_AGC_CONTROL_FLTR_CAL);
}
}
/* Do PA Calibration */
if (AR_SREV_9285_11_OR_LATER(ah))
ath9k_hw_9285_pa_cal(ah, true);
/* Do NF Calibration after DC offset and other calibrations */
REG_WRITE(ah, AR_PHY_AGC_CONTROL,
REG_READ(ah, AR_PHY_AGC_CONTROL) | AR_PHY_AGC_CONTROL_NF);
ah->cal_list = ah->cal_list_last = ah->cal_list_curr = NULL;
/* Enable IQ, ADC Gain and ADC DC offset CALs */
if (AR_SREV_9100(ah) || AR_SREV_9160_10_OR_LATER(ah)) {
if (ath9k_hw_iscal_supported(ah, ADC_GAIN_CAL)) {
INIT_CAL(&ah->adcgain_caldata);
INSERT_CAL(ah, &ah->adcgain_caldata);
DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
"enabling ADC Gain Calibration.\n");
}
if (ath9k_hw_iscal_supported(ah, ADC_DC_CAL)) {
INIT_CAL(&ah->adcdc_caldata);
INSERT_CAL(ah, &ah->adcdc_caldata);
DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
"enabling ADC DC Calibration.\n");
}
if (ath9k_hw_iscal_supported(ah, IQ_MISMATCH_CAL)) {
INIT_CAL(&ah->iq_caldata);
INSERT_CAL(ah, &ah->iq_caldata);
DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
"enabling IQ Calibration.\n");
}
ah->cal_list_curr = ah->cal_list;
if (ah->cal_list_curr)
ath9k_hw_reset_calibration(ah, ah->cal_list_curr);
}
chan->CalValid = 0;
return true;
}
