/**
* @brief De-initialize USART registers (Registers restored to their default values).
* @param USARTx USART Instance
* @retval An ErrorStatus enumeration value:
* - SUCCESS: USART registers are de-initialized
* - ERROR: USART registers are not de-initialized
*/
ErrorStatus LL_USART_DeInit(USART_TypeDef *USARTx)
{
ErrorStatus status = SUCCESS;
/* Check the parameters */
assert_param(IS_UART_INSTANCE(USARTx));
if (USARTx == USART1)
{
/* Force reset of USART clock */
LL_APB2_GRP1_ForceReset(LL_APB2_GRP1_PERIPH_USART1);
/* Release reset of USART clock */
LL_APB2_GRP1_ReleaseReset(LL_APB2_GRP1_PERIPH_USART1);
}
else if (USARTx == USART2)
{
/* Force reset of USART clock */
LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_USART2);
/* Release reset of USART clock */
LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_USART2);
}
#if defined(USART3)
else if (USARTx == USART3)
{
/* Force reset of USART clock */
LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_USART3);
/* Release reset of USART clock */
LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_USART3);
}
#endif /* USART3 */
#if defined(UART4)
else if (USARTx == UART4)
{
/* Force reset of UART clock */
LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_UART4);
/* Release reset of UART clock */
LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_UART4);
}
#endif /* UART4 */
#if defined(UART5)
else if (USARTx == UART5)
{
/* Force reset of UART clock */
LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_UART5);
/* Release reset of UART clock */
LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_UART5);
}
#endif /* UART5 */
else
{
status = ERROR;
}
return (status);
}
/**
* @brief Initialize USART Clock related settings according to the
* specified parameters in the USART_ClockInitStruct.
* @note As some bits in USART configuration registers can only be written when the USART is disabled (USART_CR1_UE bit =0),
* USART IP should be in disabled state prior calling this function. Otherwise, ERROR result will be returned.
* @param USARTx USART Instance
* @param USART_ClockInitStruct: pointer to a @ref LL_USART_ClockInitTypeDef structure
* that contains the Clock configuration information for the specified USART peripheral.
* @retval An ErrorStatus enumeration value:
* - SUCCESS: USART registers related to Clock settings are initialized according to USART_ClockInitStruct content
* - ERROR: Problem occurred during USART Registers initialization
*/
ErrorStatus LL_USART_ClockInit(USART_TypeDef *USARTx, LL_USART_ClockInitTypeDef *USART_ClockInitStruct)
{
ErrorStatus status = SUCCESS;
/* Check USART Instance and Clock signal output parameters */
assert_param(IS_UART_INSTANCE(USARTx));
assert_param(IS_LL_USART_CLOCKOUTPUT(USART_ClockInitStruct->ClockOutput));
/* USART needs to be in disabled state, in order to be able to configure some bits in
CRx registers */
if (LL_USART_IsEnabled(USARTx) == 0U)
{
/*---------------------------- USART CR2 Configuration -----------------------*/
/* If Clock signal has to be output */
if (USART_ClockInitStruct->ClockOutput == LL_USART_CLOCK_DISABLE)
{
/* Deactivate Clock signal delivery :
* - Disable Clock Output: USART_CR2_CLKEN cleared
*/
LL_USART_DisableSCLKOutput(USARTx);
}
else
{
/* Ensure USART instance is USART capable */
assert_param(IS_USART_INSTANCE(USARTx));
/* Check clock related parameters */
assert_param(IS_LL_USART_CLOCKPOLARITY(USART_ClockInitStruct->ClockPolarity));
assert_param(IS_LL_USART_CLOCKPHASE(USART_ClockInitStruct->ClockPhase));
assert_param(IS_LL_USART_LASTBITCLKOUTPUT(USART_ClockInitStruct->LastBitClockPulse));
/*---------------------------- USART CR2 Configuration -----------------------
* Configure USARTx CR2 (Clock signal related bits) with parameters:
* - Enable Clock Output: USART_CR2_CLKEN set
* - Clock Polarity: USART_CR2_CPOL bit according to USART_ClockInitStruct->ClockPolarity value
* - Clock Phase: USART_CR2_CPHA bit according to USART_ClockInitStruct->ClockPhase value
* - Last Bit Clock Pulse Output: USART_CR2_LBCL bit according to USART_ClockInitStruct->LastBitClockPulse value.
*/
MODIFY_REG(USARTx->CR2,
USART_CR2_CLKEN | USART_CR2_CPHA | USART_CR2_CPOL | USART_CR2_LBCL,
USART_CR2_CLKEN | USART_ClockInitStruct->ClockPolarity |
USART_ClockInitStruct->ClockPhase | USART_ClockInitStruct->LastBitClockPulse);
}
}
/* Else (USART not in Disabled state => return ERROR */
else
{
status = ERROR;
}
return (status);
}
/** @brief: init state flag acc to info in huart
* @details: used in Uart3Debug_Init, private
****************************************************************/
static HAL_StatusTypeDef MyHAL_UARTInit(UART_HandleTypeDef * huart) {
/* Check the UART handle allocation */
if (huart == NULL) {
return HAL_ERROR;
}
/* Check the parameters */
if (huart->Init.HwFlowCtl != UART_HWCONTROL_NONE) {
/* The hardware flow control is available only for USART1, USART2, USART3 and USART6 */
assert_param(IS_UART_HWFLOW_INSTANCE(huart->Instance));
assert_param(IS_UART_HARDWARE_FLOW_CONTROL(huart->Init.HwFlowCtl));
} else {
assert_param(IS_UART_INSTANCE(huart->Instance));
}
assert_param(IS_UART_WORD_LENGTH(huart->Init.WordLength));
assert_param(IS_UART_OVERSAMPLING(huart->Init.OverSampling));
if (huart->State == HAL_UART_STATE_RESET) {
/* Allocate lock resource and initialize it */
huart->Lock = HAL_UNLOCKED;
/* Init the low level hardware */
// HAL_NVIC_SetPriority(USART3_IRQn, 0, 0);
// HAL_NVIC_EnableIRQ(USART3_IRQn);
}
huart->State = HAL_UART_STATE_BUSY;
/* Disable the peripheral */
__HAL_UART_DISABLE(huart);
/* Set the UART Communication parameters */
MyUARTSetConfig(huart);
/* In asynchronous mode, the following bits must be kept cleared:
* - LINEN and CLKEN bits in the USART_CR2 register,
* - SCEN, HDSEL and IREN bits in the USART_CR3 register.*/
huart->Instance->CR2 &= ~(USART_CR2_LINEN | USART_CR2_CLKEN);
huart->Instance->CR3 &=
~(USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN);
/* Enable the peripheral */
__HAL_UART_ENABLE(huart);
/* Initialize the UART state */
huart->ErrorCode = HAL_UART_ERROR_NONE;
huart->State = HAL_UART_STATE_READY;
return HAL_OK;
} /* MyHAL_UARTInit */
/**
* @brief Initialize USART registers according to the specified
* parameters in USART_InitStruct.
* @note As some bits in USART configuration registers can only be written when the USART is disabled (USART_CR1_UE bit =0),
* USART IP should be in disabled state prior calling this function. Otherwise, ERROR result will be returned.
* @note Baud rate value stored in USART_InitStruct BaudRate field, should be valid (different from 0).
* @param USARTx USART Instance
* @param USART_InitStruct: pointer to a LL_USART_InitTypeDef structure
* that contains the configuration information for the specified USART peripheral.
* @retval An ErrorStatus enumeration value:
* - SUCCESS: USART registers are initialized according to USART_InitStruct content
* - ERROR: Problem occurred during USART Registers initialization
*/
ErrorStatus LL_USART_Init(USART_TypeDef *USARTx, LL_USART_InitTypeDef *USART_InitStruct)
{
ErrorStatus status = ERROR;
uint32_t periphclk = LL_RCC_PERIPH_FREQUENCY_NO;
#if (defined(USART4) || defined(USART5))
LL_RCC_ClocksTypeDef RCC_Clocks;
#endif
/* Check the parameters */
assert_param(IS_UART_INSTANCE(USARTx));
assert_param(IS_LL_USART_BAUDRATE(USART_InitStruct->BaudRate));
assert_param(IS_LL_USART_DATAWIDTH(USART_InitStruct->DataWidth));
assert_param(IS_LL_USART_STOPBITS(USART_InitStruct->StopBits));
assert_param(IS_LL_USART_PARITY(USART_InitStruct->Parity));
assert_param(IS_LL_USART_DIRECTION(USART_InitStruct->TransferDirection));
assert_param(IS_LL_USART_HWCONTROL(USART_InitStruct->HardwareFlowControl));
assert_param(IS_LL_USART_OVERSAMPLING(USART_InitStruct->OverSampling));
/* USART needs to be in disabled state, in order to be able to configure some bits in
CRx registers */
if (LL_USART_IsEnabled(USARTx) == 0U)
{
/*---------------------------- USART CR1 Configuration -----------------------
* Configure USARTx CR1 (USART Word Length, Parity, Mode and Oversampling bits) with parameters:
* - DataWidth: USART_CR1_M bits according to USART_InitStruct->DataWidth value
* - Parity: USART_CR1_PCE, USART_CR1_PS bits according to USART_InitStruct->Parity value
* - TransferDirection: USART_CR1_TE, USART_CR1_RE bits according to USART_InitStruct->TransferDirection value
* - Oversampling: USART_CR1_OVER8 bit according to USART_InitStruct->OverSampling value.
*/
MODIFY_REG(USARTx->CR1,
(USART_CR1_M | USART_CR1_PCE | USART_CR1_PS |
USART_CR1_TE | USART_CR1_RE | USART_CR1_OVER8),
(USART_InitStruct->DataWidth | USART_InitStruct->Parity |
USART_InitStruct->TransferDirection | USART_InitStruct->OverSampling));
/*---------------------------- USART CR2 Configuration -----------------------
* Configure USARTx CR2 (Stop bits) with parameters:
* - Stop Bits: USART_CR2_STOP bits according to USART_InitStruct->StopBits value.
* - CLKEN, CPOL, CPHA and LBCL bits are to be configured using LL_USART_ClockInit().
*/
LL_USART_SetStopBitsLength(USARTx, USART_InitStruct->StopBits);
/*---------------------------- USART CR3 Configuration -----------------------
* Configure USARTx CR3 (Hardware Flow Control) with parameters:
* - HardwareFlowControl: USART_CR3_RTSE, USART_CR3_CTSE bits according to USART_InitStruct->HardwareFlowControl value.
*/
LL_USART_SetHWFlowCtrl(USARTx, USART_InitStruct->HardwareFlowControl);
/*---------------------------- USART BRR Configuration -----------------------
* Retrieve Clock frequency used for USART Peripheral
*/
#if defined(USART1)
if (USARTx == USART1)
{
periphclk = LL_RCC_GetUSARTClockFreq(LL_RCC_USART1_CLKSOURCE);
}
#endif /* USART1 */
#if defined(USART1)
else if (USARTx == USART2)
#else
if (USARTx == USART2)
#endif
{
periphclk = LL_RCC_GetUSARTClockFreq(LL_RCC_USART2_CLKSOURCE);
}
#if defined(USART4)
else if (USARTx == USART4)
{
/* USART4 clock is PCLK1 */
LL_RCC_GetSystemClocksFreq(&RCC_Clocks);
periphclk = RCC_Clocks.PCLK1_Frequency;
}
#endif /* USART4 */
#if defined(USART5)
else if (USARTx == USART5)
{
/* USART5 clock is PCLK1 */
LL_RCC_GetSystemClocksFreq(&RCC_Clocks);
periphclk = RCC_Clocks.PCLK1_Frequency;
}
#endif /* USART5 */
else
{
/* Nothing to do, as error code is already assigned to ERROR value */
}
/* Configure the USART Baud Rate :
- valid baud rate value (different from 0) is required
- Peripheral clock as returned by RCC service, should be valid (different from 0).
*/
if ((periphclk != LL_RCC_PERIPH_FREQUENCY_NO)
&& (USART_InitStruct->BaudRate != 0U))
{
status = SUCCESS;
LL_USART_SetBaudRate(USARTx,
periphclk,
USART_InitStruct->OverSampling,
USART_InitStruct->BaudRate);
}
}
/* Endif (=> USART not in Disabled state => return ERROR) */
return (status);
}