void usb_init_slave(void)
{
struct s3c24x0_gpio * const gpioregs = s3c24x0_get_base_gpio();
char *mode;
udelay(100000);
Isr_Init();
writel((readl(&gpioregs->MISCCR) & ~((1<<3) | (1<<13))), &gpioregs->MISCCR);
// USBD is selected instead of USBH1
// USB port 1 is enabled.
//
// USBD should be initialized first of all.
//
isUsbdSetConfiguration=0;
UsbdMain();
udelay(100000);
writel((readl(&gpioregs->GPCDAT) | (1<<5)), &gpioregs->GPCDAT);
/* enable USB Device, thisway.diy */
#if USBDMA
mode="DMA";
#else
mode="Int";
#endif
download_run=0; //The default menu is the Download & Run mode.
printf("USB slave is enable!\n");
}
void Main(void)
{
//硬件初始化
var_Init();//初始化定时器相关的参数
Port_Init();//IO端口初始化
Isr_Init();//中断初始化
Uart_Init(0,115200);//串口初始化
Uart_Select(0);
_init_alloc(0x32500000,0x333fffff);//初始化堆地址：15M，使能malloc等存储分配函数
setlocale(LC_ALL,"C");//使能本地函数，如sprintf等
Timer4_Init();
lcdTest();
}
void Main(void)
{
Port_Init(); //IO端口初始化
Isr_Init(); //中断初始化
Uart_Init(0,115200);//串口初始化
Uart_Select(0);
Uart_Printf("\n\nDM2410 Experiment System (ADS) Ver1.10\n") ;//打印系统信息
Test_SDI();
}
void usb_init_slave(void)
{
struct s3c24x0_gpio * const gpioregs = s3c24x0_get_base_gpio();
char *mode;
udelay(100000);
Isr_Init();
writel((readl(&gpioregs->misccr) & ~((1<<3) | (1<<13))), &gpioregs->misccr);
// USBD is selected instead of USBH1
// USB port 1 is enabled.
//
// USBD should be initialized first of all.
//
isUsbdSetConfiguration=0;
UsbdMain();
udelay(100000);
writel((readl(&gpioregs->gpcdat) | (1<<5)), &gpioregs->gpcdat);
/* enable USB Device, thisway.diy */
#if USBDMA
mode="DMA";
#else
mode="Int";
#endif
download_run=0; //The default menu is the Download & Run mode.
printf("\n");
printf("+------------------------------------------------------------+\n");
printf("| S3C2440A USB Downloader (Port from tekkamanninja 2012 Aug) |\n");
printf("+------------------------------------------------------------+\n");
printf("USB: IN_ENDPOINT:1 OUT_ENDPOINT:3\n");
printf("FORMAT: <ADDR(DATA):4>+<SIZE(n+10):4>+<DATA:n>+<CS:2>\n");
printf("NOTE: Power off/on or press the reset button for 1 sec\n");
printf(" in order to get a valid USB device address.\n");
printf("\n");
}
void usb_init_slave(void)
{
char *mode;
int i;
U8 key;
U32 mpll_val, upll_val, divn_upll=0;
extern int bBootFrmNORFlash(void);
/* start add by ll ,replace the Port_Init() */
gpioregs = S3C24X0_GetBase_GPIO();
gpioregs->GPGCON = 0xfd95ffba; /* thisway.diy, GPG12-->OUTPUT, GPG9-->OUTPUT for FS2410, as USB Device enable */
gpioregs->GPGUP = 0xffff; // The pull up function is disabled GPG[15:0]
gpioregs->GPGDAT &= ~(1<<12); /* disable USB Device, enable later, thisway.diy */
/* end ll */
clk_powerregs = S3C24X0_GetBase_CLOCK_POWER();
usbdevregs = S3C24X0_GetBase_USB_DEVICE();
dmaregs = S3C24X0_GetBase_DMAS();
udelay(100000);
#if 0
// USB device detection control
rGPGCON &= ~(3<<24);
rGPGCON |= (1<<24); // output
rGPGUP |= (1<<12); // pullup disable
rGPGDAT |= (1<<12); // output
#endif
//ChangeUPllValue(60,4,2); // 48MHz
//for(i=0; i<7; i++);
//ChangeClockDivider(13,12);
//ChangeMPllValue(97,1,2); //296Mhz
Isr_Init();
gpioregs->MISCCR=gpioregs->MISCCR&~(1<<3); // USBD is selected instead of USBH1
gpioregs->MISCCR=gpioregs->MISCCR&~(1<<13); // USB port 1 is enabled.
//
// USBD should be initialized first of all.
//
isUsbdSetConfiguration=0;
#if 0
UsbdMain();
MMU_Init(); //MMU should be reconfigured or turned off for the debugger,
//After downloading, MMU should be turned off for the MMU based program,such as WinCE.
#else
//thisway.diy MMU_EnableICache();
UsbdMain();
udelay(100000);
gpioregs->GPGDAT |= ((1<<9) | (1<<12)); /* enable USB Device, thisway.diy */
gpioregs->GPBDAT |= (1<<9); /* enable USB Device, thisway.diy */
gpioregs->GPCDAT |= (1<<5); /* enable USB Device, thisway.diy */
#endif
#if USBDMA
mode="DMA";
#else
mode="Int";
#endif
// CLKOUT0/1 select.
//printf("CLKOUT0:MPLL in, CLKOUT1:RTC clock.\n");
//Clk0_Enable(0); // 0:MPLLin, 1:UPLL, 2:FCLK, 3:HCLK, 4:PCLK, 5:DCLK0
//Clk1_Enable(2); // 0:MPLLout, 1:UPLL, 2:RTC, 3:HCLK, 4:PCLK, 5:DCLK1
// Clk0_Disable();
// Clk1_Disable();
mpll_val = clk_powerregs->MPLLCON;
upll_val = clk_powerregs->UPLLCON;
if (0) //(!bBootFrmNORFlash())
{
S3C24X0_INTERRUPT * intregs;
intregs = S3C24X0_GetBase_INTERRUPT();
printf("UPLLVal [M:%xh,P:%xh,S:%xh]\n", (upll_val&(0xff<<12))>>12,(upll_val&(0x3f<<4))>>4,(upll_val&0x3));
printf("MPLLVal [M:%xh,P:%xh,S:%xh]\n", (mpll_val&(0xff<<12))>>12,(mpll_val&(0x3f<<4))>>4,(mpll_val&0x3));
printf("CLKDIVN:%xh\n", clk_powerregs->CLKDIVN);
intregs->INTSUBMSK = 0x3ff;
gpioregs->GPBDAT = 0x740;
gpioregs->GPCDAT = 0x20;
gpioregs->GPGDAT = 0xba2c;
printf("\nINTMOD = %x\n", intregs->INTMOD);
printf("INTMSK = %x\n", intregs->INTMSK);
printf("INTSUBMSK = %x\n", intregs->INTSUBMSK);
printf("\nGPBCON = %x\n", gpioregs->GPBCON);
printf("GPBDAT = %x\n", gpioregs->GPBDAT);
printf("GPCCON = %x\n", gpioregs->GPCCON);
printf("GPCDAT = %x\n", gpioregs->GPCDAT);
printf("GPGCON = %x\n", gpioregs->GPGCON);
printf("GPGDAT = %x\n", gpioregs->GPGDAT);
/*
printf("\n\n");
printf("+---------------------------------------------+\n");
printf("| S3C2440A USB Downloader ver R0.03 2004 Jan |\n");
printf("+---------------------------------------------+\n");
// printf("FCLK=%4.1fMHz,%s mode\n",FCLK/1000000.,mode);
printf("USB: IN_ENDPOINT:1 OUT_ENDPOINT:3\n");
printf("FORMAT: <ADDR(DATA):4>+<SIZE(n+10):4>+<DATA:n>+<CS:2>\n");
printf("NOTE: Power off/on or press the reset button for 1 sec\n");
printf(" in order to get a valid USB device address.\n");
printf("\n");
*/
}
void usb_init(void)
{
char *mode;
int i;
U8 key;
U32 mpll_val, upll_val, divn_upll=0;
extern int bBootFrmNORFlash(void);
Port_Init();
clk_powerregs = S3C24X0_GetBase_CLOCK_POWER();
usbdevregs = S3C24X0_GetBase_USB_DEVICE();
dmaregs = S3C24X0_GetBase_DMAS();
udelay(100000);
#if 0
// USB device detection control
rGPGCON &= ~(3<<24);
rGPGCON |= (1<<24); // output
rGPGUP |= (1<<12); // pullup disable
rGPGDAT |= (1<<12); // output
#endif
//ChangeUPllValue(60,4,2); // 48MHz
//for(i=0; i<7; i++);
//ChangeClockDivider(13,12);
//ChangeMPllValue(97,1,2); //296Mhz
Isr_Init();
gpioregs->MISCCR=gpioregs->MISCCR&~(1<<3); // USBD is selected instead of USBH1
gpioregs->MISCCR=gpioregs->MISCCR&~(1<<13); // USB port 1 is enabled.
//
// USBD should be initialized first of all.
//
isUsbdSetConfiguration=0;
#if 0
UsbdMain();
MMU_Init(); //MMU should be reconfigured or turned off for the debugger,
//After downloading, MMU should be turned off for the MMU based program,such as WinCE.
#else
//mike.arm9 MMU_EnableICache();
UsbdMain();
udelay(100000);
gpioregs->GPGDAT |= (1<<12); /* enable USB Device, mike.arm9 */
gpioregs->GPBDAT |= (1<<9); /* enable USB Device, mike.arm9 */
gpioregs->GPCDAT |= (1<<5); /* enable USB Device, mike.arm9 */
#endif
#if USBDMA
mode="DMA";
#else
mode="Int";
#endif
// CLKOUT0/1 select.
//printf("CLKOUT0:MPLL in, CLKOUT1:RTC clock.\n");
//Clk0_Enable(0); // 0:MPLLin, 1:UPLL, 2:FCLK, 3:HCLK, 4:PCLK, 5:DCLK0
//Clk1_Enable(2); // 0:MPLLout, 1:UPLL, 2:RTC, 3:HCLK, 4:PCLK, 5:DCLK1
// Clk0_Disable();
// Clk1_Disable();
mpll_val = clk_powerregs->MPLLCON;
upll_val = clk_powerregs->UPLLCON;
if (1) //(!bBootFrmNORFlash())
{
printf("UPLLVal [M:%xh,P:%xh,S:%xh]\n", (upll_val&(0xff<<12))>>12,(upll_val&(0x3f<<4))>>4,(upll_val&0x3));
printf("MPLLVal [M:%xh,P:%xh,S:%xh]\n", (mpll_val&(0xff<<12))>>12,(mpll_val&(0x3f<<4))>>4,(mpll_val&0x3));
printf("CLKDIVN:%xh\n", clk_powerregs->CLKDIVN);
printf("\n\n");
printf("+---------------------------------------------+\n");
printf("| S3C2440A USB Downloader ver R0.03 2004 Jan |\n");
printf("+---------------------------------------------+\n");
// printf("FCLK=%4.1fMHz,%s mode\n",FCLK/1000000.,mode);
printf("USB: IN_ENDPOINT:1 OUT_ENDPOINT:3\n");
printf("FORMAT: <ADDR(DATA):4>+<SIZE(n+10):4>+<DATA:n>+<CS:2>\n");
printf("NOTE: Power off/on or press the reset button for 1 sec\n");
printf(" in order to get a valid USB device address.\n");
printf("\n");
}
int main( void)
{
int autoID,dispID,dispIndex;
int timerval;
U16 btnStat,oldStat;
rGPACDH = rdGPACDH & ~(1<<5) | (0<<5); // RDATA_OEN : enable
rGPHCON=rGPHCON&~(0xf<<26)|(0xa<<26);
rMISCCR=rMISCCR&~((0x7<<8)|(0x7<<4))|(0x3<<8)|(0x2<<4);
// test code start setting in option.h
SetCLKDIV( Startup_ARMCLKdiv, Startup_PREdiv, Startup_HCLKdiv, Startup_PCLKdiv);
SetMPLL( Startup_MDIV, Startup_PDIV, Startup_SDIV);
SystemCLK(0);
Isr_Init();
MMU_Init();
SPI_Init();
Console();
printf("\n\n***********TST-500_OTM1283+AUO5.7_720*1280 Test Program Ver 0.0***********\n");
//printf("MPLL=%.2fMHz, ARMCLK=%.2fMHz (%d:%d:%d), HCLK=%.2fMHz, PCLK=%.2fMHz\n\n",
// (float)MPLL/1000000,(float)ARMCLK/1000000,ARMCLKdiv+1,(ARMCLKdiv+1)*(HCLKdiv+1),(ARMCLKdiv+1)*(HCLKdiv+1)*(PCLKdiv+1),(float)HCLK/1000000,(float)PCLK/1000000);
Init_SSD2805_SPI(); //2805 spi初始化，位于/Peripheral/Video/LCD/Display.c文件
SetLcdPort(); //2443 RGB端口及相关寄存器配置，其中RGB参数位于Display.h文件
SPI_READ_ID(0xb0);
Key_Init(); //按键初始化
dispID = 0;
dispIndex = 1;
autoID = 0;
timerval = 0;
btnStat=0;
oldStat=0;
while(1) //
{
if(dispIndex)
{
dispIndex = 0;
switch(dispID)
{
case 0:
disp_color(0xF800,0,0,XSIZE,YSIZE);
break; //显示R颜色
case 1:
disp_color(0x07E0,0,0,XSIZE,YSIZE);
break; //显示G颜色
case 2:
disp_color(0x001F,0,0,XSIZE,YSIZE);
break; //显示B颜色
case 3:
disp_9WB();
break;
case 4:
disp_color_table();
break;
case 5:
disp_gray();
break;
case 6:
disp_color(0xffff,0,0,XSIZE,YSIZE);
break; //显示白色
case 7:
disp_color(0x0000,0,0,XSIZE,YSIZE);
K9S1208_RdBmp(TFT_RAM1,TFT_SMC_BLK1,TFT_BmpSize);
break;//把图片数据拷贝到内存，TFT_RAM1,TFT_SMC_BLK1定义在Display.h文件 break;//Delay(10); //显示黑色
case 8:
disp_bmp((U16 *)TFT_RAM1,0,0,XSIZE,YSIZE);
K9S1208_RdBmp(TFT_RAM2,TFT_SMC_BLK2,TFT_BmpSize);
break; //显示内存的图片的数据
case 9:
disp_bmp((U16 *)TFT_RAM2,0,0,XSIZE,YSIZE);
K9S1208_RdBmp(TFT_RAM3,TFT_SMC_BLK3,TFT_BmpSize);
break; //显示内存的图片的数据
case 10:
disp_bmp((U16 *)TFT_RAM3,0,0,XSIZE,YSIZE);
K9S1208_RdBmp(TFT_RAM4,TFT_SMC_BLK4,TFT_BmpSize);
break; //显示内存的图片的数据
case 11:
disp_bmp((U16 *)TFT_RAM4,0,0,XSIZE,YSIZE);
break;
}
// printf("\display id = %d\n",dispID);
Delay_MS(400);
}
if(autoID)
{
timerval++;
if(timerval>30)
{
timerval = 0;
dispID++;
if(dispID>BmpMAX) dispID=0;
dispIndex = 1;
//Init_SSD2805_SPI();
}
}
btnStat = rGPJDAT;
btnStat = (~btnStat)&0x0007;
//printf("\ndisplay btn = 0x%x\n",btnStat);
if(btnStat)
{
if(((btnStat&0x01)==0x01) && ((oldStat&0x01)==0x00)) //GPJ0自动手动切换
{
if(autoID) autoID = 0;
else autoID = 1;
}
if(((btnStat&0x02)==0x02) && ((oldStat&0x02)==0x00)) //GPJ1画面向前翻
{
dispID++;
if(dispID>BmpMAX) dispID=0;
dispIndex = 1;
//Init_SSD2828();
}
if(((btnStat&0x04)==0x04) && ((oldStat&0x04)==0x00)) //GPJ2画面向后翻
{
// dispID++;
if(dispID>0) dispID--;
else dispID = BmpMAX;
dispIndex = 1;
}
// Delay_MS(100);
}
Delay_MS(50); //延时，并且监视串口
oldStat = btnStat;
}
//--------------------------------------------------------------------------------------------
}
