/******************************************************************************* ** ** Function gatt_disconnect ** ** Description This function is called to disconnect to an ATT device. ** ** Parameter rem_bda: remote device address to disconnect from. ** ** Returns TRUE: if connection found and to be disconnected; otherwise ** return FALSE. ** *******************************************************************************/ BOOLEAN gatt_disconnect (BD_ADDR rem_bda) { tGATT_TCB *p_tcb = gatt_find_tcb_by_addr(rem_bda); BOOLEAN ret = FALSE; tGATT_CH_STATE ch_state; GATT_TRACE_DEBUG0 ("gatt_disconnect "); if (p_tcb != NULL) { ret = TRUE; if ( (ch_state = gatt_get_ch_state(p_tcb)) != GATT_CH_CLOSING ) { if (p_tcb->att_lcid == L2CAP_ATT_CID) { if (ch_state == GATT_CH_OPEN) { /* only LCB exist between remote device and local */ ret = L2CA_RemoveFixedChnl (L2CAP_ATT_CID, rem_bda); } else { gatt_set_ch_state(p_tcb, GATT_CH_CLOSING); ret = L2CA_CancelBleConnectReq (rem_bda); } } else { ret = L2CA_DisconnectReq(p_tcb->att_lcid); } } else { GATT_TRACE_DEBUG0 ("gatt_disconnect already in closing state"); } } return ret; }
/******************************************************************************* ** ** Function l2cble_advertiser_conn_comp ** ** Description This function is called when an HCI Connection Complete ** event is received while we are an advertiser (so we are slave). ** ** Returns void ** *******************************************************************************/ void l2cble_advertiser_conn_comp (UINT16 handle, BD_ADDR bda, tBLE_ADDR_TYPE type, UINT16 conn_interval, UINT16 conn_latency, UINT16 conn_timeout) { int i; tL2C_LCB *p_lcb; tBTM_SEC_DEV_REC *p_dev_rec; UNUSED(type); UNUSED(conn_interval); UNUSED(conn_latency); UNUSED(conn_timeout); /* See if we have a link control block for the remote device */ p_lcb = l2cu_find_lcb_by_bd_addr (bda, BT_TRANSPORT_LE); /* If we don't have one, create one and accept the connection. */ if (!p_lcb) { p_lcb = l2cu_allocate_lcb (bda, FALSE, BT_TRANSPORT_LE); if (!p_lcb) { btm_sec_disconnect (handle, HCI_ERR_NO_CONNECTION); L2CAP_TRACE_ERROR ("l2cble_advertiser_conn_comp - failed to allocate LCB"); return; } else { if (!l2cu_initialize_fixed_ccb (p_lcb, L2CAP_ATT_CID, &l2cb.fixed_reg[L2CAP_ATT_CID - L2CAP_FIRST_FIXED_CHNL].fixed_chnl_opts)) { btm_sec_disconnect (handle, HCI_ERR_NO_CONNECTION); L2CAP_TRACE_WARNING ("l2cble_scanner_conn_comp - LCB but no CCB"); return ; } } } /* Save the handle */ p_lcb->handle = handle; /* Connected OK. Change state to connected, we were advertising, so we are slave */ p_lcb->link_role = HCI_ROLE_SLAVE; p_lcb->transport = BT_TRANSPORT_LE; /* update link parameter, set slave link as non-spec default upon link up */ p_lcb->min_interval = p_lcb->max_interval = conn_interval; p_lcb->timeout = conn_timeout; p_lcb->latency = conn_latency; p_lcb->conn_update_mask = L2C_BLE_NOT_DEFAULT_PARAM; /* Tell BTM Acl management about the link */ p_dev_rec = btm_find_or_alloc_dev (bda); btm_acl_created (bda, NULL, p_dev_rec->sec_bd_name, handle, p_lcb->link_role, BT_TRANSPORT_LE); #if BLE_PRIVACY_SPT == TRUE btm_ble_disable_resolving_list(BTM_BLE_RL_ADV, TRUE); #endif p_lcb->peer_chnl_mask[0] = L2CAP_FIXED_CHNL_ATT_BIT | L2CAP_FIXED_CHNL_BLE_SIG_BIT | L2CAP_FIXED_CHNL_SMP_BIT; if (!HCI_LE_SLAVE_INIT_FEAT_EXC_SUPPORTED(controller_get_interface()->get_features_ble()->as_array)) { p_lcb->link_state = LST_CONNECTED; l2cu_process_fixed_chnl_resp (p_lcb); } /* when adv and initiating are both active, cancel the direct connection */ if (l2cb.is_ble_connecting && memcmp(bda, l2cb.ble_connecting_bda, BD_ADDR_LEN) == 0) { L2CA_CancelBleConnectReq(bda); } }