/*
LCD module initialization according to LCDConfig.h
it is used as default configuration of the LCD
*/
void vfnLCD_Init(void) {
// enable IRCLK
/*Enable IRCLK LCD source and disconnect from FLL by clearing IREFS */
MCG_C1= 0x02;
SIM_SCGC5 |= SIM_SCGC5_SLCD_MASK | SIM_SCGC5_PORTB_MASK | SIM_SCGC5_PORTC_MASK | SIM_SCGC5_PORTD_MASK | SIM_SCGC5_PORTE_MASK;
// Enable IRCLK
MCG_C1 |= MCG_C1_IRCLKEN_MASK | MCG_C1_IREFSTEN_MASK;
MCG_C2 |= !MCG_C2_IRCS_MASK ; //0 32KHZ internal reference clock; 1= 4MHz irc
//vfnLCD_interrupt_init();
LCD_GCR = 0x0;
LCD_AR = 0x0;
// lcd_pinmux(0);
/* LCD configurartion according to */
LCD_GCR = ( LCD_GCR_RVEN_MASK*_LCDRVEN
| LCD_GCR_RVTRIM(_LCDRVTRIM) //0-15
| LCD_GCR_CPSEL_MASK*_LCDCPSEL
/* | LCD_GCR_HREFSEL_MASK*_LCDHREF */
|LCD_GCR_LADJ(_LCDLOADADJUST) //0-3*/
/* | LCD_GCR_VSUPPLY(_LCDSUPPLY) //0-3*/
/* |!LCD_GCR_LCDIEN_MASK */
|!LCD_GCR_FDCIEN_MASK
| LCD_GCR_ALTDIV(_LCDALTDIV) //0-3
/* |!LCD_GCR_LCDWAIT_MASK */
|!LCD_GCR_LCDSTP_MASK
|!LCD_GCR_LCDEN_MASK
| LCD_GCR_SOURCE_MASK*_LCDCLKSOURCE
| LCD_GCR_ALTSOURCE_MASK*_LCDALRCLKSOURCE
| LCD_GCR_LCLK(_LCDLCK) //0-7
| LCD_GCR_DUTY(_LCDDUTY) //0-7
);
lcd_alternate_mode = LCD_NORMAL_MODE; //Message will be written to default backplanes if = 4
vfnLCD_EnablePins(); // Enable LCD pins and **Configure BackPlanes**
LCD_GCR |= LCD_GCR_LCDEN_MASK;
/* LCD_GCR |= LCD_GCR_LCDIEN_MASK; // Enable interrupts */
/* Configure LCD Auxiliar Register*/
LCD_AR = LCD_AR_BRATE(_LCDBLINKRATE); // all other flags set as zero
vfnLCD_Write_Msg("1235");
}
void vfnLCD_Init(void)
{
SIM_SCGC5 |= SIM_SCGC5_SLCD_MASK | SIM_SCGC5_PORTB_MASK | SIM_SCGC5_PORTC_MASK | SIM_SCGC5_PORTD_MASK | SIM_SCGC5_PORTE_MASK;
//* configure pins for LCD operation
PORTC_PCR20 = 0x00000000; //VLL2
PORTC_PCR21 = 0x00000000; //VLL1
PORTC_PCR22 = 0x00000000; //VCAP2
PORTC_PCR23 = 0x00000000; //VCAP1
// Enable IRCLK
MCG_C1 = MCG_C1_IRCLKEN_MASK | MCG_C1_IREFSTEN_MASK;
MCG_C2 &= ~MCG_C2_IRCS_MASK ; //0 32KHZ internal reference clock; 1= 4MHz irc
vfnLCD_interrupt_init();
LCD_GCR = 0x0;
LCD_AR = 0x0;
// lcd_pinmux(0);
/* LCD configurartion according to */
LCD_GCR = ( LCD_GCR_RVEN_MASK*_LCDRVEN
| LCD_GCR_RVTRIM(_LCDRVTRIM) //0-15
| LCD_GCR_CPSEL_MASK*_LCDCPSEL
| LCD_GCR_LADJ(_LCDLOADADJUST) //0-3*/
| LCD_GCR_VSUPPLY_MASK*_LCDSUPPLY //0-1*/
|!LCD_GCR_FDCIEN_MASK
| LCD_GCR_ALTDIV(_LCDALTDIV) //0-3
|!LCD_GCR_LCDDOZE_MASK
|!LCD_GCR_LCDSTP_MASK
|!LCD_GCR_LCDEN_MASK //WILL BE ENABLE ON SUBSEQUENT STEP
| LCD_GCR_SOURCE_MASK*_LCDCLKSOURCE
| LCD_GCR_ALTSOURCE_MASK*_LCDALRCLKSOURCE
| LCD_GCR_LCLK(_LCDLCK) //0-7
| LCD_GCR_DUTY(_LCDDUTY) //0-7
);
lcd_alternate_mode = LCD_NORMAL_MODE; //Message will be written to default backplanes if = 4
vfnEnablePins(); // Enable LCD pins and Configure BackPlanes
LCD_GCR |= LCD_GCR_LCDEN_MASK;
/* LCD_GCR |= LCD_GCR_LCDIEN_MASK; // Enable interrupts */
/* Configure LCD Auxiliar Register*/
LCD_AR = LCD_AR_BRATE(_LCDBLINKRATE); // all other flags set as zero
// print_slcd_registers();
}
/**
void _LCDModule_Init(void)
Parameters: None
Description: This functions configures the registers of the SLCD Module
*/
void _SLCDModule_Init(void)
{
MCG_C1 |= MCG_C1_IRCLKEN_MASK;
//enable clock gate for Ports
SIM_SCGC5 |= ( !SIM_SCGC5_LPTIMER_MASK
| !SIM_SCGC5_REGFILE_MASK
| !SIM_SCGC5_TSI_MASK
| SIM_SCGC5_PORTB_MASK
| SIM_SCGC5_PORTC_MASK
| SIM_SCGC5_PORTD_MASK
);
// Master General Purpose Control Register - Set mux to LCD analog operation.
// After RESET these register are configured as 0 but indicated here for reference
PORTB_PCR1 = PORT_PCR_MUX(0); //LCD_P1
PORTB_PCR2 = PORT_PCR_MUX(0); //LCD_P2
PORTB_PCR3 = PORT_PCR_MUX(0); //LCD_P3
PORTB_PCR4 = PORT_PCR_MUX(0); //LCD_P4
PORTB_PCR5 = PORT_PCR_MUX(0); //LCD_P5
PORTB_PCR6 = PORT_PCR_MUX(0); //LCD_P6
PORTB_PCR7 = PORT_PCR_MUX(0); //LCD_P7
PORTB_PCR8 = PORT_PCR_MUX(0); //LCD_P8
PORTB_PCR9 = PORT_PCR_MUX(0); //LCD_P9
PORTB_PCR10 = PORT_PCR_MUX(0); //LCD_P10
PORTB_PCR11 = PORT_PCR_MUX(0); //LCD_P11
PORTB_PCR16 = PORT_PCR_MUX(0); //LCD_P12
PORTB_PCR17 = PORT_PCR_MUX(0); //LCD_P13
PORTB_PCR18 = PORT_PCR_MUX(0); //LCD_P14
PORTB_PCR19 = PORT_PCR_MUX(0); //LCD_P15
PORTB_PCR20 = PORT_PCR_MUX(0); //LCD_P16
PORTB_PCR21 = PORT_PCR_MUX(0); //LCD_P17
PORTB_PCR22 = PORT_PCR_MUX(0); //LCD_P18
PORTB_PCR23 = PORT_PCR_MUX(0); //LCD_P19
PORTC_PCR0 = PORT_PCR_MUX(0); //LCD_P20
PORTC_PCR1 = PORT_PCR_MUX(0); //LCD_P21
PORTC_PCR2 = PORT_PCR_MUX(0); //LCD_P22
PORTC_PCR3 = PORT_PCR_MUX(0); //LCD_P23
PORTC_PCR4 = PORT_PCR_MUX(0); //LCD_P24
PORTC_PCR5 = PORT_PCR_MUX(0); //LCD_P25
PORTC_PCR6 = PORT_PCR_MUX(0); //LCD_P26
PORTC_PCR7 = PORT_PCR_MUX(0); //LCD_P27
PORTC_PCR8 = PORT_PCR_MUX(0); //LCD_P28
PORTC_PCR9 = PORT_PCR_MUX(0); //LCD_P29
PORTC_PCR10 = PORT_PCR_MUX(0); //LCD_P30
PORTC_PCR11 = PORT_PCR_MUX(0); //LCD_P31
PORTC_PCR12 = PORT_PCR_MUX(0); //LCD_P32
PORTC_PCR13 = PORT_PCR_MUX(0); //LCD_P33
PORTC_PCR14 = PORT_PCR_MUX(0); //LCD_P34
PORTC_PCR15 = PORT_PCR_MUX(0); //LCD_P35
PORTC_PCR16 = PORT_PCR_MUX(0); //LCD_P36
PORTC_PCR17 = PORT_PCR_MUX(0); //LCD_P37
PORTC_PCR18 = PORT_PCR_MUX(0); //LCD_P38
PORTC_PCR19 = PORT_PCR_MUX(0); //LCD_P39
PORTD_PCR0 = PORT_PCR_MUX(0); //LCD_P40
PORTD_PCR1 = PORT_PCR_MUX(0); //LCD_P41
PORTD_PCR2 = PORT_PCR_MUX(0); //LCD_P42
PORTD_PCR3 = PORT_PCR_MUX(0); //LCD_P43
PORTD_PCR4 = PORT_PCR_MUX(0); //LCD_P44
PORTD_PCR5 = PORT_PCR_MUX(0); //LCD_P45
PORTD_PCR6 = PORT_PCR_MUX(0); //LCD_P46
PORTD_PCR7 = PORT_PCR_MUX(0); //LCD_P47
// Configure NVIC for SLCD interrupt SLCD interrupt vector = 102
// NVICICPR2 |= (1<<22); //Clear any pending interrupts on LCD
// NVICISER2 |= (1<<22); //Enable interrupts from LCD interrupt*/
// SLCD clock gate on
SIM_SCGC3 |= SIM_SCGC3_SLCD_MASK;
// Disable LCD
LCD_GCR = 0;
// Enable LCD pins 1-47
LCD_PENH = 0;
LCD_PENH = 0x0000FFFF;
LCD_PENL = 0;
LCD_PENL = 0xFFFFFFFE;
// Enable LCD pins used as Backplanes 0-7
LCD_BPENH = 0;
LCD_BPENH = 0x0000FF00;
LCD_BPENL = 0;
// Configure backplane phase
LCD_WF43TO40 = 0x08040201;
LCD_WF47TO44 = 0x80402010;
// Fill information on what segments are going to be turned on. Front Plane information
LCD_WF3TO0 = 0;
LCD_WF7TO4 = 0;
LCD_WF11TO8 = 0;
LCD_WF15TO12 = 0;
LCD_WF19TO16 = 0;
LCD_WF23TO20 = 0;
LCD_WF27TO24 = 0;
LCD_WF31TO28 = 0;
LCD_WF35TO32 = 0;
LCD_WF39TO36 = 0;
// Configure LCD Control Register
LCD_GCR |= ( LCD_GCR_CPSEL_MASK
| LCD_GCR_RVEN_MASK
| LCD_GCR_RVTRIM(15)
| !LCD_GCR_HREFSEL_MASK // ( 0 - 3 Volts LCDs / 1 - 5 Volts LCDs)
| LCD_GCR_LADJ(3) //0-3
| LCD_GCR_VSUPPLY(3) //0-3
| !LCD_GCR_LCDIEN_MASK
| !LCD_GCR_FDCIEN_MASK
| LCD_GCR_ALTDIV(1) //0-3
| !LCD_GCR_LCDWAIT_MASK
| !LCD_GCR_LCDSTP_MASK
| !LCD_GCR_LCDEN_MASK
| LCD_GCR_SOURCE_MASK
| LCD_GCR_LCLK(0) //0-3
| LCD_GCR_DUTY(7) //0-7
);
// Enable LCD module
LCD_GCR |= LCD_GCR_LCDEN_MASK;
}