mp_uint_t sdcard_read_blocks(uint8_t *buff, uint32_t sector, uint32_t count)
{
HAL_SD_ErrorTypedef err;
// If buffer is unaligned or located in CCM don't use DMA.
if (CCM_BUFFER(buff) || UNALIGNED_BUFFER(buff)) {
if (UNALIGNED_BUFFER(buff)) {
printf("unaligned read buf:%p count%lu \n", buff, count);
}
// This transfer has to be done in an atomic section.
mp_uint_t atomic_state = MICROPY_BEGIN_ATOMIC_SECTION();
err = HAL_SD_ReadBlocks(&SDHandle, (uint32_t*)buff,
sector * SDCARD_BLOCK_SIZE, SDCARD_BLOCK_SIZE, count);
MICROPY_END_ATOMIC_SECTION(atomic_state);
} else {
// Disable USB IRQ to prevent FatFS/MSC contention
HAL_NVIC_DisableIRQ(OTG_FS_IRQn); __DSB(); __ISB();
dma_init(SDIO_TXRX_STREAM, SDIO_TXRX_CHANNEL, DMA_PERIPH_TO_MEMORY);
err = HAL_SD_ReadBlocks_DMA(&SDHandle, (uint32_t*)buff,
sector * SDCARD_BLOCK_SIZE, SDCARD_BLOCK_SIZE, count);
if (err == SD_OK) {
err = HAL_SD_CheckReadOperation(&SDHandle, SDIO_TIMEOUT);
}
if (err != SD_OK) {
printf("read buf:%p addr:%lu count%lu error:%d\n", buff, sector, count, err);
}
dma_deinit();
HAL_NVIC_EnableIRQ(OTG_FS_IRQn);
}
return (err != SD_OK);
}
mp_uint_t sdcard_write_blocks(const uint8_t *buff, uint32_t sector, uint32_t count)
{
HAL_SD_ErrorTypedef err;
mp_uint_t atomic_state = MICROPY_BEGIN_ATOMIC_SECTION();
err = HAL_SD_WriteBlocks(&SDHandle, (uint32_t*)buff,
sector * SDCARD_BLOCK_SIZE, SDCARD_BLOCK_SIZE, count);
MICROPY_END_ATOMIC_SECTION(atomic_state);
return (err != SD_OK);
}
mp_uint_t sdcard_write_blocks(const uint8_t *src, uint32_t block_num, uint32_t num_blocks) {
// check that src pointer is aligned on a 4-byte boundary
if (((uint32_t)src & 3) != 0) {
return SD_ERROR;
}
// check that SD card is initialised
if (sd_handle.Instance == NULL) {
return SD_ERROR;
}
// We must disable IRQs because the SDIO peripheral has a small FIFO
// buffer and we can't let it drain to empty in the middle of a write.
// This will not be needed when SD uses DMA for transfer.
mp_uint_t atomic_state = MICROPY_BEGIN_ATOMIC_SECTION();
HAL_SD_ErrorTypedef err = HAL_SD_WriteBlocks_BlockNumber(&sd_handle, (uint32_t*)src, block_num, SDCARD_BLOCK_SIZE, num_blocks);
MICROPY_END_ATOMIC_SECTION(atomic_state);
return err;
}
mp_obj_t mp_alloc_emergency_exception_buf(mp_obj_t size_in) {
mp_int_t size = mp_obj_get_int(size_in);
void *buf = NULL;
if (size > 0) {
buf = m_malloc(size);
}
int old_size = mp_emergency_exception_buf_size;
void *old_buf = mp_emergency_exception_buf;
// Update the 2 variables atomically so that an interrupt can't occur
// between the assignments.
mp_uint_t irq_state = MICROPY_BEGIN_ATOMIC_SECTION();
mp_emergency_exception_buf_size = size;
mp_emergency_exception_buf = buf;
MICROPY_END_ATOMIC_SECTION(irq_state);
if (old_buf != NULL) {
m_free(old_buf, old_size);
}
return mp_const_none;
}
STATIC void wiz_cris_enter(void) {
wiznet5k_obj.cris_state = MICROPY_BEGIN_ATOMIC_SECTION();
}
// Support functions for memory protection. lwIP has its own memory management
// routines for its internal structures, and since they might be called in
// interrupt handlers, they need some protection.
sys_prot_t sys_arch_protect() {
return (sys_prot_t)MICROPY_BEGIN_ATOMIC_SECTION();
}
int main(void)
{
FRESULT f_res;
int sensor_init_ret;
// Stack limit should be less than real stack size, so we
// had chance to recover from limit hit.
mp_stack_set_limit((char*)&_ram_end - (char*)&_heap_end - 1024);
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Global MSP (MCU Support Package) initialization
*/
HAL_Init();
// basic sub-system init
pendsv_init();
timer_tim3_init();
led_init();
soft_reset:
// check if user switch held to select the reset mode
led_state(LED_RED, 1);
led_state(LED_GREEN, 1);
led_state(LED_BLUE, 1);
#if MICROPY_HW_ENABLE_RTC
rtc_init();
#endif
// GC init
gc_init(&_heap_start, &_heap_end);
// Micro Python init
mp_init();
mp_obj_list_init(mp_sys_path, 0);
mp_obj_list_init(mp_sys_argv, 0);
readline_init0();
pin_init0();
extint_init0();
timer_init0();
rng_init0();
i2c_init0();
spi_init0();
uart_init0();
pyb_usb_init0();
usbdbg_init();
sensor_init_ret = sensor_init();
/* Export functions to the global python namespace */
mp_store_global(qstr_from_str("randint"), (mp_obj_t)&py_randint_obj);
mp_store_global(qstr_from_str("cpu_freq"), (mp_obj_t)&py_cpu_freq_obj);
mp_store_global(qstr_from_str("vcp_is_connected"), (mp_obj_t)&py_vcp_is_connected_obj);
if (sdcard_is_present()) {
sdcard_init();
FRESULT res = f_mount(&fatfs, "1:", 1);
if (res != FR_OK) {
__fatal_error("could not mount SD\n");
}
// Set CWD and USB medium to SD
f_chdrive("1:");
pyb_usb_storage_medium = PYB_USB_STORAGE_MEDIUM_SDCARD;
} else {
storage_init();
// try to mount the flash
FRESULT res = f_mount(&fatfs, "0:", 1);
if (res == FR_NO_FILESYSTEM) {
// create a fresh fs
make_flash_fs();
} else if (res != FR_OK) {
__fatal_error("could not access LFS\n");
}
// Set CWD and USB medium to flash
f_chdrive("0:");
pyb_usb_storage_medium = PYB_USB_STORAGE_MEDIUM_FLASH;
}
// turn boot-up LEDs off
led_state(LED_RED, 0);
led_state(LED_GREEN, 0);
led_state(LED_BLUE, 0);
// init USB device to default setting if it was not already configured
if (!(pyb_usb_flags & PYB_USB_FLAG_USB_MODE_CALLED)) {
pyb_usb_dev_init(USBD_VID, USBD_PID_CDC_MSC, USBD_MODE_CDC_MSC, NULL);
}
// check sensor init result
if (sensor_init_ret != 0) {
char buf[512];
snprintf(buf, sizeof(buf), "Failed to init sensor, error:%d", sensor_init_ret);
__fatal_error(buf);
}
// Run self tests the first time only
f_res = f_stat("selftest.py", NULL);
if (f_res == FR_OK) {
nlr_buf_t nlr;
if (nlr_push(&nlr) == 0) {
// Parse, compile and execute the self-tests script.
pyexec_file("selftest.py");
nlr_pop();
} else {
// Get the exception message. TODO: might be a hack.
mp_obj_str_t *str = mp_obj_exception_get_value((mp_obj_t)nlr.ret_val);
// If any of the self-tests fail log the exception message
// and loop forever. Note: IDE exceptions will not be caught.
__fatal_error((const char*) str->data);
}
// Success: remove self tests script and flush cache
f_unlink("selftest.py");
storage_flush();
}
// Run the main script from the current directory.
f_res = f_stat("main.py", NULL);
if (f_res == FR_OK) {
nlr_buf_t nlr;
if (nlr_push(&nlr) == 0) {
// Parse, compile and execute the main script.
pyexec_file("main.py");
nlr_pop();
} else {
mp_obj_print_exception(&mp_plat_print, (mp_obj_t)nlr.ret_val);
if (nlr_push(&nlr) == 0) {
flash_error(3);
nlr_pop();
}// if this gets interrupted again ignore it.
}
}
// Enter REPL
nlr_buf_t nlr;
for (;;) {
if (nlr_push(&nlr) == 0) {
while (usbdbg_script_ready()) {
nlr_buf_t nlr;
vstr_t *script_buf = usbdbg_get_script();
// clear debugging flags
usbdbg_clear_flags();
// re-init MP
mp_uint_t atomic_state = MICROPY_BEGIN_ATOMIC_SECTION();
mp_init();
MICROPY_END_ATOMIC_SECTION(atomic_state);
// execute the script
if (nlr_push(&nlr) == 0) {
// parse, compile and execute script
pyexec_str(script_buf);
nlr_pop();
} else {
mp_obj_print_exception(&mp_plat_print, (mp_obj_t)nlr.ret_val);
}
}
// clear debugging flags
usbdbg_clear_flags();
// re-init MP
mp_uint_t atomic_state = MICROPY_BEGIN_ATOMIC_SECTION();
mp_init();
MICROPY_END_ATOMIC_SECTION(atomic_state);
// no script run REPL
pyexec_friendly_repl();
nlr_pop();
}
}
printf("PYB: sync filesystems\n");
storage_flush();
printf("PYB: soft reboot\n");
goto soft_reset;
}