int main(void)
{
// Configure the device for maximum performance but do not change the PBDIV
// Given the options, this function will change the flash wait states, RAM
// wait state and enable prefetch cache but will not change the PBDIV.
// The PBDIV value is already set via the pragma FPBDIV option above..
SYSTEMConfig(SYS_FREQ, SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
// Auto-configure the PIC32 for optimum performance at the specified operating frequency.
SYSTEMConfigPerformance(SYS_FREQ);
// osc source, PLL multipler value, PLL postscaler , RC divisor
OSCConfig(OSC_POSC_PLL, OSC_PLL_MULT_20, OSC_PLL_POST_1, OSC_FRC_POST_1);
// Configure the PB bus to run at 1/4 the CPU frequency
OSCSetPBDIV(OSC_PB_DIV_4);
// Enable multi-vector interrupts
INTEnableSystemMultiVectoredInt();
INTEnableInterrupts();
// Set up the UART peripheral so we can send serial data.
UARTConfigure(UART_USED, UART_ENABLE_PINS_TX_RX_ONLY);
UARTSetFifoMode(UART_USED, UART_INTERRUPT_ON_TX_NOT_FULL | UART_INTERRUPT_ON_RX_NOT_EMPTY);
UARTSetLineControl(UART_USED, UART_DATA_SIZE_8_BITS | UART_PARITY_NONE | UART_STOP_BITS_1);
UARTSetDataRate(UART_USED, F_PB, UART_BAUD_RATE);
UARTEnable(UART_USED, UART_ENABLE | UART_TX);
// And configure printf/scanf to use the correct UART.
if (UART_USED == UART1) {
__XC_UART = 1;
}
/***************************************************************************************************
* Your code goes in between this comment and the following one with asterisks.
**************************************************************************************************/
/***************************************************************************************************
* Your code goes in between this comment and the preceding one with asterisks.
**************************************************************************************************/
// Returning from main() is bad form in embedded environments. So we sit and spin.
while (1);
}
int main(void)
{
// Configure the device for maximum performance but do not change the PBDIV
// Given the options, this function will change the flash wait states, RAM
// wait state and enable prefetch cache but will not change the PBDIV.
// The PBDIV value is already set via the pragma FPBDIV option above..
SYSTEMConfig(SYS_FREQ, SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
// Auto-configure the PIC32 for optimum performance at the specified operating frequency.
SYSTEMConfigPerformance(SYS_FREQ);
// osc source, PLL multipler value, PLL postscaler , RC divisor
OSCConfig(OSC_POSC_PLL, OSC_PLL_MULT_20, OSC_PLL_POST_1, OSC_FRC_POST_1);
// Configure the PB bus to run at 1/4 the CPU frequency
OSCSetPBDIV(OSC_PB_DIV_4);
// Enable multi-vector interrupts
INTEnableSystemMultiVectoredInt();
// Set up the UART peripheral so we can send serial data.
UARTConfigure(UART_USED, UART_ENABLE_PINS_TX_RX_ONLY);
UARTSetFifoMode(UART_USED, UART_INTERRUPT_ON_TX_NOT_FULL | UART_INTERRUPT_ON_RX_NOT_EMPTY);
UARTSetLineControl(UART_USED, UART_DATA_SIZE_8_BITS | UART_PARITY_NONE | UART_STOP_BITS_1);
UARTSetDataRate(UART_USED, F_PB, UART_BAUD_RATE);
UARTEnable(UART_USED, UART_ENABLE | UART_TX);
// And configure printf/scanf to use the correct UART.
if (UART_USED == UART1) {
__XC_UART = 1;
}
extern void T1Setup();
extern void T1Stop();
extern void T1Start();
// Enable LED outputs 0-7 by setting TRISE register
TRISECLR = 0x00FF;
// Initialize the PORTE to 0
PORTECLR = 0x00FF;
// Set the lowest bit
PORTESET = 1;
OledInit();
OledDisplayOn();
printf("Starting Timer Set-up\n");
T1Setup();
int stopped = 0, reset = 0;
extern volatile int milliseconds;
int temp = 0;
int count = 0;
printTime(0, 0);
while(1) {
// Display the least significant part of the time for debugging
int x = PORTD & 0xfff;
if(x == 272) {
if(stopped) {
stopped = 0;
T1Start();
}
if(reset)
reset = 0;
if(milliseconds - temp >= 1000) {
count++;
int minutes = count/60;
int seconds = count % 60;
printTime(minutes,seconds);
temp = milliseconds;
}
}
else if(x == 784 || x == 528) {
if(reset != 1) {
printTime(0, 0);
T1Stop();
stopped = 1;
reset = 1;
count = 0;
}
}
else {
stopped = 1;
continue;
}
}
}
int main(void)
{
// Configure the device for maximum performance but do not change the PBDIV
// Given the options, this function will change the flash wait states, RAM
// wait state and enable prefetch cache but will not change the PBDIV.
// The PBDIV value is already set via the pragma FPBDIV option above..
SYSTEMConfig(SYS_FREQ, SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
// Auto-configure the PIC32 for optimum performance at the specified operating frequency.
SYSTEMConfigPerformance(SYS_FREQ);
// osc source, PLL multipler value, PLL postscaler , RC divisor
OSCConfig(OSC_POSC_PLL, OSC_PLL_MULT_20, OSC_PLL_POST_1, OSC_FRC_POST_1);
// Configure the PB bus to run at 1/4 the CPU frequency
OSCSetPBDIV(OSC_PB_DIV_4);
// Enable multi-vector interrupts
INTEnableSystemMultiVectoredInt();
INTEnableInterrupts();
// Set up the UART peripheral so we can send serial data.
UARTConfigure(UART_USED, UART_ENABLE_PINS_TX_RX_ONLY);
UARTSetFifoMode(UART_USED, UART_INTERRUPT_ON_TX_NOT_FULL | UART_INTERRUPT_ON_RX_NOT_EMPTY);
UARTSetLineControl(UART_USED, UART_DATA_SIZE_8_BITS | UART_PARITY_NONE | UART_STOP_BITS_1);
UARTSetDataRate(UART_USED, F_PB, UART_BAUD_RATE);
UARTEnable(UART_USED, UART_ENABLE | UART_TX);
// And configure printf/scanf to use the correct UART.
if (UART_USED == UART1) {
__XC_UART = 1;
}
// Enable LED outputs 0-7 by setting TRISE register
TRISECLR = 0x00FF;
// Initialize the PORTE to 0
PORTECLR = 0x00FF;
// Set the lowest bit
int mask = 1;
PORTESET = mask;
int delay = 0xA0000;
// Loop forever, it is bad to exit in an embedded processor.
int count=0; // move this into the delay function
while (1) {
// Move this printf into your getDelay function!
printf("Hello, world! %d\n",count++);
// Replace this with the getDelay function call!
//int delay = getDelay();
// do nothing for a lot of cycles
int i=0;
for(i=0;i<delay;i++)
;
// shift left by 1
mask = mask << 1;
// rotate around if more than 8 bits
if (mask & 0x0100)
mask = 1;
// Set the output to the new mask
PORTE=mask;
delay = 0xA0000 + 0x40000*sin((double)count/10) + 0x20000*cos((double)count/5);
if(delay < 0)
delay *= -1;
}
}
int main(void)
{
// Configure the device for maximum performance but do not change the PBDIV
// Given the options, this function will change the flash wait states, RAM
// wait state and enable prefetch cache but will not change the PBDIV.
// The PBDIV value is already set via the pragma FPBDIV option above..
SYSTEMConfig(SYS_FREQ, SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
// Auto-configure the PIC32 for optimum performance at the specified operating frequency.
SYSTEMConfigPerformance(SYS_FREQ);
// osc source, PLL multipler value, PLL postscaler , RC divisor
OSCConfig(OSC_POSC_PLL, OSC_PLL_MULT_20, OSC_PLL_POST_1, OSC_FRC_POST_1);
// Configure the PB bus to run at 1/4 the CPU frequency
OSCSetPBDIV(OSC_PB_DIV_4);
// Enable multi-vector interrupts
INTEnableSystemMultiVectoredInt();
INTEnableInterrupts();
// Set up the UART peripheral so we can send serial data.
UARTConfigure(UART_USED, UART_ENABLE_PINS_TX_RX_ONLY);
UARTSetFifoMode(UART_USED, UART_INTERRUPT_ON_TX_NOT_FULL | UART_INTERRUPT_ON_RX_NOT_EMPTY);
UARTSetLineControl(UART_USED, UART_DATA_SIZE_8_BITS | UART_PARITY_NONE | UART_STOP_BITS_1);
UARTSetDataRate(UART_USED, F_PB, UART_BAUD_RATE);
UARTEnable(UART_USED, UART_ENABLE | UART_TX);
// And configure printf/scanf to use the correct UART.
if (UART_USED == UART1) {
__XC_UART = 1;
}
// Initialize the array
char seed1[] = __TIME__;
unsigned int seed2 = (((unsigned int)(seed1[7] ^ seed1[2])) << 8) | ((unsigned int)(seed1[4] ^ seed1[6]));
srand(seed2);
unsigned char vals[] = { rand(), rand(), rand(), rand(), rand() };
int valsToBeSorted[] = {vals[0], vals[1], vals[2], vals[3], vals[4]};
// Sort the array in place.
int i, j;
for (i = 0; i < 5; ++i)
{
int aTemp = valsToBeSorted[i];
for (j = i - 1; j >= 0; j--) {
if (valsToBeSorted[j] <= aTemp)
break;
valsToBeSorted[j + 1] = valsToBeSorted[j];
}
valsToBeSorted [j+1] = aTemp;
}
// Print out the array
printf("[");
for (i=0;i<4;++i) {
printf("%d, ", valsToBeSorted[i]);
}
printf("%d]\n", valsToBeSorted[i]);
/*
* Returning from main() is bad form in embedded environments. So we
* sit and spin.
*/
while (1);
}
int main()
{
// Configure the device for maximum performance but do not change the PBDIV
// Given the options, this function will change the flash wait states, RAM
// wait state and enable prefetch cache but will not change the PBDIV.
// The PBDIV value is already set via the pragma FPBDIV option above..
SYSTEMConfig(F_SYS, SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
// Auto-configure the PIC32 for optimum performance at the specified operating frequency.
SYSTEMConfigPerformance(F_SYS);
// osc source, PLL multipler value, PLL postscaler , RC divisor
OSCConfig(OSC_POSC_PLL, OSC_PLL_MULT_20, OSC_PLL_POST_1, OSC_FRC_POST_1);
// Configure the PB bus to run at 1/4th the CPU frequency, so 20MHz.
OSCSetPBDIV(OSC_PB_DIV_4);
// Enable multi-vector interrupts
INTEnableSystemMultiVectoredInt();
INTEnableInterrupts();
// Configure Timer 2 using PBCLK as input. We configure it using a 1:16 prescalar, so each timer
// tick is actually at F_PB / 16 Hz, so setting PR2 to F_PB / 16 / 100 yields a .01s timer.
OpenTimer2(T2_ON | T2_SOURCE_INT | T2_PS_1_16, F_PB / 16 / 100);
// Set up the timer interrupt with a medium priority of 4.
INTClearFlag(INT_T2);
INTSetVectorPriority(INT_TIMER_2_VECTOR, INT_PRIORITY_LEVEL_4);
INTSetVectorSubPriority(INT_TIMER_2_VECTOR, INT_SUB_PRIORITY_LEVEL_0);
INTEnable(INT_T2, INT_ENABLED);
/******************************** Your custom code goes below here ********************************/
int check;
OledInit();
AdcInit();
LEDS_INIT();
check = GameInit();
if(check == STANDARD_ERROR) {
FATAL_ERROR();
}
float currPage;
float binSize;
float titleSize;
float descSize;
float numPages;
uint8_t roomExit;
uint16_t adcValue = 0;
while(1) {
roomExit = GameGetCurrentRoomExits();
LEDS_SET(roomExit);
while(buttonEvents == 0) {
descSize = GameGetCurrentRoomDescription(roomData.description);
titleSize = GameGetCurrentRoomTitle(roomData.title);
numPages = ((titleSize + descSize) / MAX_OLED_PIXELS);
binSize = (ADC_MAX_VALUE / numPages);
if(AdcChanged()) {
adcValue = AdcRead();
}
currPage = (adcValue / binSize);
if(currPage < 1) {
char titleArray[TITLE_OLED_SPACE] = {0};
char descriptionBuffer[FIRST_PG_DESCRIPTION_OLED_SPACE] = {0};
strncpy(descriptionBuffer, roomData.description, DESCRIPTION_COPY);
sprintf(titleArray, "%s\n%s", roomData.title, descriptionBuffer);
OledClear(OLED_COLOR_BLACK);
OledDrawString(titleArray);
} else {
char buffer[MAX_OLED_PIXELS] = {0};
int buffIndex;
buffIndex = (int)currPage * MAX_OLED_PIXELS;
strncpy(buffer, (roomData.description + buffIndex - OFFSET), MAX_OLED_PIXELS);
OledClear(OLED_COLOR_BLACK);
OledDrawString(buffer);
}
OledUpdate();
}
if((buttonEvents & BUTTON_EVENT_4UP) && (roomExit & GAME_ROOM_EXIT_NORTH_EXISTS)) {
GameGoNorth();
} else if((buttonEvents & BUTTON_EVENT_3UP) && (roomExit & GAME_ROOM_EXIT_EAST_EXISTS)) {
GameGoEast();
} else if((buttonEvents & BUTTON_EVENT_2UP) && (roomExit & GAME_ROOM_EXIT_SOUTH_EXISTS)) {
GameGoSouth();
} else if((buttonEvents & BUTTON_EVENT_1UP) && (roomExit & GAME_ROOM_EXIT_WEST_EXISTS)) {
GameGoWest();
}
buttonEvents = BUTTON_EVENT_NONE;
}
/**************************************************************************************************/
while (1);
}