void DRV_SPI1_Deinitialize ( void )
{
/* Disable the interrupts */
SYS_INT_SourceDisable(INT_SOURCE_SPI_2_TRANSMIT);
SYS_INT_SourceDisable(INT_SOURCE_SPI_2_RECEIVE);
SYS_INT_SourceDisable(INT_SOURCE_SPI_2_ERROR);
/* Disable the SPI Module */
PLIB_SPI_Disable(SPI_ID_2);
return;
}
void DRV_SPI0_Initialize(void)
{
PLIB_SPI_Disable(SPI_ID_1);
PLIB_SPI_MasterEnable(SPI_ID_1);
PLIB_SPI_SlaveSelectEnable(SPI_ID_1);
PLIB_SPI_StopInIdleDisable(SPI_ID_1);
PLIB_SPI_ClockPolaritySelect(SPI_ID_1, SPI_CLOCK_POLARITY_IDLE_LOW);
PLIB_SPI_OutputDataPhaseSelect(SPI_ID_1, SPI_OUTPUT_DATA_PHASE_ON_IDLE_TO_ACTIVE_CLOCK);
PLIB_SPI_InputSamplePhaseSelect(SPI_ID_1, SPI_INPUT_SAMPLING_PHASE_IN_MIDDLE);
PLIB_SPI_CommunicationWidthSelect(SPI_ID_1, SPI_COMMUNICATION_WIDTH_8BITS);
PLIB_SPI_FramedCommunicationDisable( SPI_ID_1 );
PLIB_SPI_AudioProtocolDisable(SPI_ID_1);
PLIB_SPI_FIFOEnable( SPI_ID_1 );
PLIB_SPI_BaudRateSet(SPI_ID_1, SYS_CLK_PeripheralFrequencyGet(CLK_BUS_PERIPHERAL_2), 1000000);
PLIB_SPI_Enable(SPI_ID_1);
}
int32_t DRV_SPI_SetupHardware(struct DRV_SPI_DRIVER_OBJECT * driverObject, const DRV_SPI_INIT * const init)
{
const register SPI_MODULE_ID spiId = init->spiId;
/* disable the SPI*/
PLIB_SPI_Disable(spiId);
/* Set up Master or Slave Mode*/
if (init->spiMode == DRV_SPI_MODE_MASTER)
{
PLIB_SPI_MasterEnable ( spiId );
}
else
if (init->spiMode == DRV_SPI_MODE_SLAVE)
{
PLIB_SPI_SlaveEnable ( spiId );
}
else
{
SYS_ASSERT(false, "\r\nInvalid SPI Configuration.");
return -1;
}
/* Set up if the SPI is allowed to run while the rest of the CPU is in idle mode*/
if (init->allowIdleRun)
{
PLIB_SPI_StopInIdleDisable( spiId );
}
else
{
PLIB_SPI_StopInIdleEnable( spiId );
}
/* Set up close Polarity and output data phase*/
switch(init->clockMode)
{
case DRV_SPI_CLOCK_MODE_IDLE_LOW_EDGE_RISE:
PLIB_SPI_ClockPolaritySelect( spiId, SPI_CLOCK_POLARITY_IDLE_LOW );
PLIB_SPI_OutputDataPhaseSelect( spiId, SPI_OUTPUT_DATA_PHASE_ON_IDLE_TO_ACTIVE_CLOCK );
break;
case DRV_SPI_CLOCK_MODE_IDLE_LOW_EDGE_FALL:
PLIB_SPI_ClockPolaritySelect( spiId, SPI_CLOCK_POLARITY_IDLE_LOW );
PLIB_SPI_OutputDataPhaseSelect( spiId, SPI_OUTPUT_DATA_PHASE_ON_ACTIVE_TO_IDLE_CLOCK );
break;
case DRV_SPI_CLOCK_MODE_IDLE_HIGH_EDGE_FALL: //TODO: Make sure these are right
PLIB_SPI_ClockPolaritySelect( spiId, SPI_CLOCK_POLARITY_IDLE_HIGH );
PLIB_SPI_OutputDataPhaseSelect( spiId, SPI_OUTPUT_DATA_PHASE_ON_IDLE_TO_ACTIVE_CLOCK );
break;
case DRV_SPI_CLOCK_MODE_IDLE_HIGH_EDGE_RISE:
PLIB_SPI_ClockPolaritySelect( spiId, SPI_CLOCK_POLARITY_IDLE_HIGH );
PLIB_SPI_OutputDataPhaseSelect( spiId, SPI_OUTPUT_DATA_PHASE_ON_ACTIVE_TO_IDLE_CLOCK );
break;
default:
SYS_ASSERT(false, "\r\nInvalid SPI Configuration.");
return -1;
}
// Set up the Input Sample Phase
PLIB_SPI_InputSamplePhaseSelect ( spiId, init->inputSamplePhase);
//Enable the SSx Pin on slave side if needed
if(init->spiMode == DRV_SPI_MODE_SLAVE && (init->spiProtocolType == DRV_SPI_PROTOCOL_TYPE_FRAMED || init->spiSlaveSSPin))
{
PLIB_SPI_PinEnable(spiId, SPI_PIN_SLAVE_SELECT);
}
else
{
PLIB_SPI_PinDisable(spiId, SPI_PIN_SLAVE_SELECT);
}
/* Communication Width Selection */
PLIB_SPI_CommunicationWidthSelect ( spiId, init->commWidth );
/* Baudrate selection */
PLIB_SPI_BaudRateSet( spiId , SYS_CLK_PeripheralFrequencyGet(init->spiClk), init->baudRate );
driverObject->currentBaudRate = init->baudRate;
driverObject->baudRate = init->baudRate;
switch (init->spiProtocolType)
{
case DRV_SPI_PROTOCOL_TYPE_STANDARD:
PLIB_SPI_FramedCommunicationDisable( spiId );
break;
case DRV_SPI_PROTOCOL_TYPE_FRAMED:
#if defined (PLIB_SPI_ExistsFrameSyncPulseDirection)
if (PLIB_SPI_ExistsFrameSyncPulseDirection(spiId))
{
PLIB_SPI_FrameSyncPulseDirectionSelect(spiId, init->framePulseDirection);
}
#endif
#if defined (PLIB_SPI_ExistsFrameSyncPulsePolarity)
if (PLIB_SPI_ExistsFrameSyncPulsePolarity(spiId))
{
PLIB_SPI_FrameSyncPulsePolaritySelect(spiId, init->framePulsePolarity);
}
#endif
#if defined (PLIB_SPI_ExistsFrameSyncPulseEdge)
if (PLIB_SPI_ExistsFrameSyncPulseEdge(spiId))
{
PLIB_SPI_FrameSyncPulseEdgeSelect(spiId, init->framePulseEdge);
}
#endif
#if defined (PLIB_SPI_ExistsFrameSyncPulseWidth)
if (PLIB_SPI_ExistsFrameSyncPulseWidth(spiId))
{
PLIB_SPI_FrameSyncPulseWidthSelect(spiId, init->framePulseWidth);
}
#endif
#if defined (PLIB_SPI_ExistsFrameSyncPulseCounter)
if (PLIB_SPI_ExistsFrameSyncPulseCounter(spiId))
{
PLIB_SPI_FrameSyncPulseCounterSelect(spiId, init->frameSyncPulse);
}
#endif
PLIB_SPI_FramedCommunicationEnable( spiId );
break;
case DRV_SPI_PROTOCOL_TYPE_AUDIO:
PLIB_SPI_FramedCommunicationDisable( spiId );
{
SYS_ASSERT(false, "\r\nInvalid SPI Configuration.");
return -1;
}
break;
default:
SYS_ASSERT(false, "\r\nInvalid SPI Configuration.");
return -1;
}
if (PLIB_SPI_ExistsFIFOControl( spiId ))
{
PLIB_SPI_FIFODisable( spiId );
}
PLIB_SPI_BufferClear( spiId );
PLIB_SPI_ReceiverOverflowClear ( spiId );
// Note: We do not enable the SPI here, that will be done by the first client.
return 0;
}
void DRV_SPI0_DeInitialize(void)
{
/* Disable SPI */
PLIB_SPI_Disable(SPI_ID_4);
}
SYS_MODULE_OBJ DRV_SPI0_Initialize(void)
{
DRV_SPI_OBJ *dObj = (DRV_SPI_OBJ*)NULL;
dObj = &gDrvSPI0Obj;
/* Disable the SPI module to configure it*/
PLIB_SPI_Disable ( SPI_ID_1 );
/* Set up Master or Slave Mode*/
PLIB_SPI_MasterEnable ( SPI_ID_1 );
PLIB_SPI_PinDisable(SPI_ID_1, SPI_PIN_SLAVE_SELECT);
/* Set up if the SPI is allowed to run while the rest of the CPU is in idle mode*/
PLIB_SPI_StopInIdleDisable( SPI_ID_1 );
/* Set up clock Polarity and output data phase*/
PLIB_SPI_ClockPolaritySelect( SPI_ID_1, SPI_CLOCK_POLARITY_IDLE_LOW );
PLIB_SPI_OutputDataPhaseSelect( SPI_ID_1, SPI_OUTPUT_DATA_PHASE_ON_IDLE_TO_ACTIVE_CLOCK );
/* Set up the Input Sample Phase*/
PLIB_SPI_InputSamplePhaseSelect ( SPI_ID_1, SPI_INPUT_SAMPLING_PHASE_IN_MIDDLE);
/* Communication Width Selection */
PLIB_SPI_CommunicationWidthSelect ( SPI_ID_1, SPI_COMMUNICATION_WIDTH_8BITS );
/* Baud rate selection */
PLIB_SPI_BaudRateSet( SPI_ID_1 , SYS_CLK_PeripheralFrequencyGet(CLK_BUS_PERIPHERAL_2), 1000000 );
/* Protocol selection */
PLIB_SPI_FramedCommunicationDisable( SPI_ID_1 );
#if defined (PLIB_SPI_ExistsAudioProtocolControl)
if (PLIB_SPI_ExistsAudioProtocolControl(SPI_ID_1))
{
PLIB_SPI_AudioProtocolDisable(SPI_ID_1);
}
#endif
/* Buffer type selection */
#if defined (PLIB_SPI_ExistsFIFOControl)
if (PLIB_SPI_ExistsFIFOControl( SPI_ID_1 ))
{
PLIB_SPI_FIFODisable( SPI_ID_1 );
}
#endif
PLIB_SPI_BufferClear( SPI_ID_1 );
PLIB_SPI_ReceiverOverflowClear ( SPI_ID_1 );
/* Initialize Queue only once for all instances of SPI driver*/
if (DRV_SPI_SYS_QUEUE_Initialize(&qmInitData, &hQueueManager) != DRV_SPI_SYS_QUEUE_SUCCESS)
{
SYS_ASSERT(false, "\r\nSPI Driver: Could not create queuing system.");
return SYS_MODULE_OBJ_INVALID;
}
/* Update the Queue parameters. */
qInitData.maxElements = 10; //Queue size
qInitData.reserveElements = 1; //Mininmum number of job queues reserved
/* Create Queue for this instance of SPI */
if (DRV_SPI_SYS_QUEUE_CreateQueue(hQueueManager, &qInitData, &dObj->queue) != DRV_SPI_SYS_QUEUE_SUCCESS)
{
SYS_ASSERT(false, "\r\nSPI Driver: Could not set up driver instance queue.");
return SYS_MODULE_OBJ_INVALID;
}
/* Update the SPI OBJECT parameters. */
dObj->operationStarting = NULL;
dObj->operationEnded = NULL;
SYS_INT_SourceDisable(INT_SOURCE_SPI_1_TRANSMIT);
SYS_INT_SourceDisable(INT_SOURCE_SPI_1_RECEIVE);
SYS_INT_SourceEnable(INT_SOURCE_SPI_1_ERROR);
/* Clear all interrupt sources */
SYS_INT_SourceStatusClear(INT_SOURCE_SPI_1_TRANSMIT);
SYS_INT_SourceStatusClear(INT_SOURCE_SPI_1_RECEIVE);
SYS_INT_SourceStatusClear(INT_SOURCE_SPI_1_ERROR);
/* Enable the Module */
PLIB_SPI_Enable(SPI_ID_1);
return (SYS_MODULE_OBJ)DRV_SPI_INDEX_0 ;
}