/**
* @brief Deinitializes all ADCs peripherals registers to their default reset values.
* @param None
* @retval None
*/
void ADC_DeInit(void)
{
/* Enable all ADCs reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC, ENABLE);
/* Release all ADCs from reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC, DISABLE);
}
void jump_to_app()
{
const struct pios_board_info *bdinfo = &pios_board_info_blob;
PIOS_LED_On(PIOS_LED_HEARTBEAT);
// Look at cm3_vectors struct in startup. In a fw image the first uint32_t contains the address of the top of irqstack
uint32_t fwIrqStackBase = (*(__IO uint32_t *)bdinfo->fw_base) & 0xFFFE0000;
// Check for the two possible irqstack locations (sram or core coupled sram)
if (fwIrqStackBase == 0x20000000 || fwIrqStackBase == 0x10000000) {
/* Jump to user application */
FLASH_Lock();
RCC_APB2PeriphResetCmd(0xffffffff, ENABLE);
RCC_APB1PeriphResetCmd(0xffffffff, ENABLE);
RCC_APB2PeriphResetCmd(0xffffffff, DISABLE);
RCC_APB1PeriphResetCmd(0xffffffff, DISABLE);
#ifdef PIOS_INCLUDE_USB
PIOS_USBHOOK_Deactivate();
#endif
JumpAddress = *(__IO uint32_t *)(bdinfo->fw_base + 4);
Jump_To_Application = (pFunction)JumpAddress;
/* Initialize user application's Stack Pointer */
__set_MSP(*(__IO uint32_t *)bdinfo->fw_base);
Jump_To_Application();
} else {
DeviceState = failed_jump;
return;
}
}
/*******************************************************************************
* 函数名称: SPI_I2S_DeInit
* 功能描述: 将SPIx外设寄存器重置为他们的缺省值(Affects also the I2Ss).
* 输入参数: SPIx x为1，2或3用于选定SPI外设。
* 输出参数: 无
* 返回参数: 无
*******************************************************************************/
void SPI_I2S_DeInit(SPI_TypeDef* SPIx)
{
/* Check the parameters [检查参数]*/
assert_param(IS_SPI_ALL_PERIPH(SPIx));
switch (*(u32*)&SPIx)
{
case SPI1_BASE:
/* Enable SPI1 reset state [使能SPI1复位状态]*/
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, ENABLE);
/* Release SPI1 from reset state [解除SPI1复位状态]*/
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, DISABLE);
break;
case SPI2_BASE:
/* Enable SPI2 reset state [使能SPI2复位状态]*/
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI2, ENABLE);
/* Release SPI2 from reset state [解除SPI2复位状态]*/
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI2, DISABLE);
break;
case SPI3_BASE:
/* Enable SPI3 reset state [使能SPI3复位状态]*/
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI3, ENABLE);
/* Release SPI3 from reset state [解除SPI3复位状态]*/
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI3, DISABLE);
break;
default:
break;
}
}
/**
* @brief Deinitializes the SPIx peripheral registers to their default
* reset values (Affects also the I2Ss).
* @param SPIx: where x can be 1, 2 or 3 to select the SPI peripheral.
* @retval None
*/
void SPI_I2S_DeInit(SPI_TypeDef* SPIx)
{
/* Check the parameters */
assert_param(IS_SPI_ALL_PERIPH(SPIx));
if (SPIx == STM32_SPI1)
{
/* Enable SPI1 reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, ENABLE);
/* Release SPI1 from reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, DISABLE);
}
else if (SPIx == SPI2)
{
/* Enable SPI2 reset state */
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI2, ENABLE);
/* Release SPI2 from reset state */
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI2, DISABLE);
}
else
{
if (SPIx == SPI3)
{
/* Enable SPI3 reset state */
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI3, ENABLE);
/* Release SPI3 from reset state */
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI3, DISABLE);
}
}
}
void spi_free(spi_t *obj) {
// Reset SPI and disable clock
if (obj->spi == SPI_1) {
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, DISABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1, DISABLE);
}
if (obj->spi == SPI_2) {
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI2, ENABLE);
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI2, DISABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI2, DISABLE);
}
if (obj->spi == SPI_3) {
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI3, ENABLE);
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI3, DISABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI3, DISABLE);
}
// Configure GPIOs
pin_function(obj->pin_miso, STM_PIN_DATA(GPIO_Mode_IN_FLOATING, 0));
pin_function(obj->pin_mosi, STM_PIN_DATA(GPIO_Mode_IN_FLOATING, 0));
pin_function(obj->pin_sclk, STM_PIN_DATA(GPIO_Mode_IN_FLOATING, 0));
pin_function(obj->pin_ssel, STM_PIN_DATA(GPIO_Mode_IN_FLOATING, 0));
}
/**
* @brief Deinitialize the SAIx peripheral registers to their default reset values.
* @param SAIx: To select the SAIx peripheral, where x can be the different instances
*
* @retval None
*/
void SAI_DeInit(SAI_TypeDef* SAIx)
{
/* Check the parameters */
assert_param(IS_SAI_PERIPH(SAIx));
if(SAIx == SAI1)
{
/* Enable SAI1 reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SAI1, ENABLE);
/* Release SAI1 from reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SAI1, DISABLE);
}
else
{
#if defined(STM32F446xx)
if(SAIx == SAI2)
{
/* Enable SAI2 reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SAI2, ENABLE);
/* Release SAI2 from reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SAI2, DISABLE);
}
#endif /* STM32F446xx */
}
}
/*
* 函数名：SPI_Config_Init()
* 输入：void
* 输出：void
* 功能：对SPI进行初始化设置
*/
void SPI1_Config_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
SPI_InitTypeDef SPI_InitStructure;
//开启外设时钟
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB,ENABLE); //PORTB时钟使能
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1,ENABLE);//SPI1时钟使能
//配置CLK端口的GPIO
GPIO_InitStructure.GPIO_Pin = SPI_CLK_GPIO_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF; //复用功能
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; //推挽输出
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_10MHz; //10MHz
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP; //上拉
GPIO_Init(SPI_CLK_GPIO_PORT,&GPIO_InitStructure);
//配置MISO端口的GPIO
GPIO_InitStructure.GPIO_Pin = SPI_MISO_GPIO_PIN ;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF; //复用功能
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; //推挽输出 因为复用的时候端口方向由内部控制，所以这里设置成输出相当于浮空输入
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_10MHz; //10MHz
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP; //上拉
GPIO_Init(SPI_MISO_GPIO_PORT,&GPIO_InitStructure);
//配置MOSI端口的GPIO
GPIO_InitStructure.GPIO_Pin = SPI_MOSI_GPIO_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF; //复用功能
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; //推挽输出
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_10MHz; //10MHz
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP; //上拉
GPIO_Init(SPI_MOSI_GPIO_PORT,&GPIO_InitStructure);
//设置端口复用
GPIO_PinAFConfig(SPI_CLK_GPIO_PORT ,SPI_CLK_AF_PINSOURCE ,GPIO_AF_SPI1); //PB3复用为SPI1
GPIO_PinAFConfig(SPI_MISO_GPIO_PORT,SPI_MISO_AF_PINSOURCE,GPIO_AF_SPI1); //PB4复用为SPI1
GPIO_PinAFConfig(SPI_MOSI_GPIO_PORT,SPI_MOSI_AF_PINSOURCE,GPIO_AF_SPI1); //PB5复用为SPI1
//这里只针对SPI口初始化
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1,ENABLE); //复位SPI1
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1,DISABLE);//停止复位SPI1
SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex; //SPI设置为双线双向全双工
SPI_InitStructure.SPI_Mode = SPI_Mode_Master; //设置SPI工作模式:设置为主SPI
SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b; //设置SPI的数据大小:SPI发送接收8位帧结构
SPI_InitStructure.SPI_CPOL = SPI_CPOL_High; //串行同步时钟的空闲状态为高电平
SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge; //串行同步时钟的第二个跳变沿（上升或下降）数据被采样
SPI_InitStructure.SPI_NSS = SPI_NSS_Soft; //NSS信号由软件（使用SSI位）管理
SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_256; ////定义波特率预分频的值:波特率预分频值为256 为主时钟分频
SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB; //指定数据传输从MSB位开始
SPI_InitStructure.SPI_CRCPolynomial = 7; //CRC值计算的多项式,含义是CRC的简记式，使用CRC-8
SPI_Init(SPIx_USE, &SPI_InitStructure); //根据SPI_InitStruct中指定的参数初始化外设SPIx寄存器
SPI_Cmd(SPIx_USE,ENABLE); //使能SPI外设
SPI1_ReadWriteByte(0xff); //启动传输
}
/**
* @brief Deinitialize the SAIx peripheral registers to their default reset values.
* @param SAIx: To select the SAIx peripheral, where x can be the different instances
*
* @retval None
*/
void SAI_DeInit(SAI_TypeDef* SAIx)
{
/* Check the parameters */
assert_param(IS_SAI_PERIPH(SAIx));
/* Enable SAI1 reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SAI1, ENABLE);
/* Release SAI1 from reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SAI1, DISABLE);
}
/**
* @brief Deinitializes ADC1 peripheral registers to their default reset values.
* @param ADCx: where x can be 1 to select the ADC peripheral.
* @retval None
*/
void ADC_DeInit(ADC_TypeDef* ADCx)
{
/* Check the parameters */
assert_param(IS_ADC_ALL_PERIPH(ADCx));
if (ADCx == ADC1) {
/* Enable ADC1 reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC1, ENABLE);
/* Release ADC1 from reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC1, DISABLE);
}
}
static void s_hal_spi_hw_init(hal_spi_t id)
{
#if defined(HAL_USE_CPU_FAM_STM32F1) || defined(HAL_USE_CPU_FAM_STM32F4)
//uint32_t RCC_APB1Periph_SPIx = (hal_spi1 == id) ? (RCC_APB1Periph_SPI1) : (RCC_APB1Periph_SPI2); RCC_APB1Periph_SPI3
if(hal_spi1 == id)
{
// spi periph clock enable
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1, ENABLE);
// the reset and exit from reset is also done by SPI_I2S_DeInit() ..... thus it can be removed from here
// reset spi periph
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, ENABLE);
// release reset
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, DISABLE);
}
else
{
uint32_t RCC_APB1Periph_SPIx = s_hal_spi_hw_rcc[HAL_spi_id2index(id)];
// spi periph clock enable
RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPIx, ENABLE);
// the reset and exit from reset is also done by SPI_I2S_DeInit() ..... thus it can be removed from here
// reset spi periph
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPIx, ENABLE);
// release reset
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPIx, DISABLE);
}
// // // system configuration controller clock
// #warning --> in stm32f4 removed "RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);" from spi_hw_init() and it still works....
// // RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
//
// // spi periph clock enable
// RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPIx, ENABLE);
//
// // reset spi periph
// RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPIx, ENABLE);
//
// // release reset
// RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPIx, DISABLE);
#else //defined(HAL_USE_CPU_FAM_*)
#error ERR --> choose a HAL_USE_CPU_FAM_*
#endif
}
/************************************************
* 函 数: Standby_SysEnter(void)
* 功 能: 系统进入待机模式
*
* 参 数: 无
*
* 返回值: 无
*************************************************/
void Standby_SysEnter(void)
{
RCC_APB2PeriphResetCmd(0x01FC, DISABLE); // 复位所有IO口
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE); // 使能PWR外设时钟
PWR_WakeUpPinCmd(ENABLE); // 使能唤醒引脚唤醒功能
PWR_EnterSTANDBYMode(); // 进入待机模式
} // Standby_SysEnter()
void SPI1_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
SPI_InitTypeDef SPI_InitStructure;
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);//使能GPIOA时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1, ENABLE);//使能SPI1时钟
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7;//PA5~7复用功能输出
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;//复用功能
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;//推挽输出
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;//100MHz
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;//上拉
GPIO_Init(GPIOA, &GPIO_InitStructure);//初始化
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8;//cs
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_PinAFConfig(GPIOA,GPIO_PinSource5,GPIO_AF_SPI1); //PA5复用为 SPI1
GPIO_PinAFConfig(GPIOA,GPIO_PinSource6,GPIO_AF_SPI1); //PA6复用为 SPI1
GPIO_PinAFConfig(GPIOA,GPIO_PinSource7,GPIO_AF_SPI1); //PA7复用为 SPI1
//这里只针对SPI口初始化
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1,ENABLE);//复位SPI1
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1,DISABLE);//停止复位SPI1
SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex; //设置SPI单向或者双向的数据模式:SPI设置为双线双向全双工
SPI_InitStructure.SPI_Mode = SPI_Mode_Master; //设置SPI工作模式:设置为主SPI
SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b; //设置SPI的数据大小:SPI发送接收8位帧结构
SPI_InitStructure.SPI_CPOL = SPI_CPOL_High; //串行同步时钟的空闲状态为高电平
SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge; //串行同步时钟的第二个跳变沿（上升或下降）数据被采样
SPI_InitStructure.SPI_NSS = SPI_NSS_Soft; //NSS信号由硬件（NSS管脚）还是软件（使用SSI位）管理:内部NSS信号有SSI位控制
SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_32; //定义波特率预分频的值:波特率预分频值为256
SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB; //指定数据传输从MSB位还是LSB位开始:数据传输从MSB位开始
SPI_InitStructure.SPI_CRCPolynomial = 7; //CRC值计算的多项式
SPI_Init(SPI1, &SPI_InitStructure); //根据SPI_InitStruct中指定的参数初始化外设SPIx寄存器
SPI_Cmd(SPI1, ENABLE); //使能SPI外设
}
void serial_free(serial_t *obj) {
// Reset UART and disable clock
if (obj->uart == UART_1) {
RCC_APB2PeriphResetCmd(RCC_APB2Periph_USART1, ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_USART1, DISABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, DISABLE);
}
if (obj->uart == UART_2) {
RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART2, ENABLE);
RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART2, DISABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, DISABLE);
}
// Configure GPIOs
pin_function(obj->pin_tx, STM_PIN_DATA(GPIO_Mode_IN, 0, GPIO_PuPd_NOPULL, 0xFF));
pin_function(obj->pin_rx, STM_PIN_DATA(GPIO_Mode_IN, 0, GPIO_PuPd_NOPULL, 0xFF));
serial_irq_ids[obj->index] = 0;
}
void jump_to_app() {
if (((*(__IO uint32_t*) START_OF_USER_CODE) & 0x2FFE0000) == 0x20000000) { /* Jump to user application */
FLASH_Lock();
RCC_APB2PeriphResetCmd(0xffffffff, ENABLE);
RCC_APB1PeriphResetCmd(0xffffffff, ENABLE);
RCC_APB2PeriphResetCmd(0xffffffff, DISABLE);
RCC_APB1PeriphResetCmd(0xffffffff, DISABLE);
_SetCNTR(0); // clear interrupt mask
_SetISTR(0); // clear all requests
JumpAddress = *(__IO uint32_t*) (START_OF_USER_CODE + 4);
Jump_To_Application = (pFunction) JumpAddress;
/* Initialize user application's Stack Pointer */
__set_MSP(*(__IO uint32_t*) START_OF_USER_CODE);
Jump_To_Application();
} else {
DeviceState = failed_jump;
return;
}
}
/*******************************************************************************
* Function Name : SPI_Config
* Description : Config the SPI1
* Pin Map : PB3-->SPI1_SCK;
* PB4-->SPI1_MISO;
* PB5-->SPI1_MOSI;
* Input : None
* Output : None
* Return : None
*******************************************************************************/
void SPI1_Config(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
SPI_InitTypeDef SPI_InitStructure;
SPI_I2S_DeInit(SPI1);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB,ENABLE); //使能GPIOB时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1,ENABLE); //使能SPI1时钟
//GPIOPB3,4,5初始化设置：复用功能输出
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF; //复用功能
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; //推挽输出
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz; //100MHz
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP; //上拉
GPIO_Init(GPIOB,&GPIO_InitStructure);
GPIO_PinAFConfig(GPIOB,GPIO_PinSource3,GPIO_AF_SPI1); //PB3复用为SPI1_SCK
GPIO_PinAFConfig(GPIOB,GPIO_PinSource4,GPIO_AF_SPI1); //PB4复用为SPI1_MISO
GPIO_PinAFConfig(GPIOB,GPIO_PinSource5,GPIO_AF_SPI1); //PB5复用为SPI1_MOSI
//Init SPI1 & Set Working Mode
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1,ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1,DISABLE);
SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex; //双线双向全双工
SPI_InitStructure.SPI_Mode = SPI_Mode_Master; //主SPI
SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b; //SPI发送接收8位帧结构
SPI_InitStructure.SPI_CPOL = SPI_CPOL_High; //串行同步时钟的空闲状态为低电平
SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge; //第二个跳变沿数据采样（下降沿）
SPI_InitStructure.SPI_NSS = SPI_NSS_Soft; //NSS信号由软件控制
SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_128;//预分频4，传输速度84M/32=2.625Mhz
SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB; //数据传输从MSB位开始
SPI_InitStructure.SPI_CRCPolynomial = 7; //CRC值计算的多项式
SPI_Init(SPI1,&SPI_InitStructure);
SPI_Cmd(SPI1,ENABLE);
SPI1_ReadWriteByte(0xFF);
}
void jump_to_app() {
const struct pios_board_info * bdinfo = &pios_board_info_blob;
if (((*(__IO uint32_t*) bdinfo->fw_base) & 0x2FFE0000) == 0x20000000) { /* Jump to user application */
FLASH_Lock();
RCC_APB2PeriphResetCmd(0xffffffff, ENABLE);
RCC_APB1PeriphResetCmd(0xffffffff, ENABLE);
RCC_APB2PeriphResetCmd(0xffffffff, DISABLE);
RCC_APB1PeriphResetCmd(0xffffffff, DISABLE);
_SetCNTR(0); // clear interrupt mask
_SetISTR(0); // clear all requests
JumpAddress = *(__IO uint32_t*) (bdinfo->fw_base + 4);
Jump_To_Application = (pFunction) JumpAddress;
/* Initialize user application's Stack Pointer */
__set_MSP(*(__IO uint32_t*) bdinfo->fw_base);
Jump_To_Application();
} else {
DeviceState = failed_jump;
return;
}
}
/**
* @brief Deinitializes the ADCx peripheral registers to their default
* reset values.
* @param ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
* @retval : None
*/
void ADC_DeInit(ADC_TypeDef* ADCx)
{
/* Check the parameters */
assert_param(IS_ADC_ALL_PERIPH(ADCx));
switch (*(uint32_t*)&ADCx)
{
case ADC1_BASE:
/* Enable ADC1 reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC1, ENABLE);
/* Release ADC1 from reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC1, DISABLE);
break;
case ADC2_BASE:
/* Enable ADC2 reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC2, ENABLE);
/* Release ADC2 from reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC2, DISABLE);
break;
case ADC3_BASE:
/* Enable ADC3 reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC3, ENABLE);
/* Release ADC3 from reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC3, DISABLE);
break;
default:
break;
}
}
/*******************************************************************************
* Function Name : SPI_DeInit
* Description : Deinitializes the SPIx peripheral registers to their default
* reset values.
* Input : - SPIx: where x can be 1 or 2 to select the SPI peripheral.
* Output : None
* Return : None
*******************************************************************************/
void SPI_DeInit(SPI_TypeDef* SPIx)
{
switch (*(u32*)&SPIx)
{
case SPI1_BASE:
/* Enable SPI1 reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, ENABLE);
/* Release SPI1 from reset state */
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SPI1, DISABLE);
break;
case SPI2_BASE:
/* Enable SPI2 reset state */
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI2, ENABLE);
/* Release SPI2 from reset state */
RCC_APB1PeriphResetCmd(RCC_APB1Periph_SPI2, DISABLE);
break;
default:
break;
}
}
/**-----------------------------------------------------------------------------
* @brief Desinitialisation de la carte.
*/
void BSP_DeInit() {
// Desactivation des interruptions
__disable_irq();
// Arret Systick
SysTick->CTRL = 0;
SysTick->LOAD = 0;
SysTick->VAL = 0;
// DeInitialisation des horloges
//RCC_AHB1PeriphClockCmd(0xFFFFFFFF, DISABLE);
RCC_AHB1PeriphResetCmd(0xFFFFFFFF, ENABLE);
RCC_AHB1PeriphResetCmd(0xFFFFFFFF, DISABLE);
//RCC_AHB2PeriphClockCmd(0xFFFFFFFF, DISABLE);
RCC_AHB2PeriphResetCmd(0xFFFFFFFF, ENABLE);
RCC_AHB2PeriphResetCmd(0xFFFFFFFF, DISABLE);
//RCC_AHB3PeriphClockCmd(0xFFFFFFFF, DISABLE);
RCC_AHB3PeriphResetCmd(0xFFFFFFFF, ENABLE);
RCC_AHB3PeriphResetCmd(0xFFFFFFFF, DISABLE);
//RCC_APB1PeriphClockCmd(0xFFFFFFFF, DISABLE);
RCC_APB1PeriphResetCmd(0xFFFFFFFF, ENABLE);
RCC_APB1PeriphResetCmd(0xFFFFFFFF, DISABLE);
//RCC_APB2PeriphClockCmd(0xFFFFFFFF, DISABLE);
RCC_APB2PeriphResetCmd(0xFFFFFFFF, ENABLE);
RCC_APB2PeriphResetCmd(0xFFFFFFFF, DISABLE);
RCC_DeInit();
// ReInit Flash
FLASH_PrefetchBufferCmd(DISABLE);
FLASH_InstructionCacheCmd(DISABLE);
FLASH_DataCacheCmd(DISABLE);
}
void jump_to_app() {
const struct pios_board_info * bdinfo = &pios_board_info_blob;
PIOS_LED_On(PIOS_LED_HEARTBEAT);
if (((*(__IO uint32_t*) bdinfo->fw_base) & 0x2FFE0000) == 0x20000000) { /* Jump to user application */
FLASH_Lock();
RCC_APB2PeriphResetCmd(0xffffffff, ENABLE);
RCC_APB1PeriphResetCmd(0xffffffff, ENABLE);
RCC_APB2PeriphResetCmd(0xffffffff, DISABLE);
RCC_APB1PeriphResetCmd(0xffffffff, DISABLE);
PIOS_USBHOOK_Deactivate();
JumpAddress = *(__IO uint32_t*) (bdinfo->fw_base + 4);
Jump_To_Application = (pFunction) JumpAddress;
/* Initialize user application's Stack Pointer */
__set_MSP(*(__IO uint32_t*) bdinfo->fw_base);
Jump_To_Application();
} else {
DeviceState = failed_jump;
return;
}
}
void configurePin(GPIO_TypeDef* port, uint16_t pinNum, GPIOMode_TypeDef mode)
{
/* Check the parameters */
assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
if (port == GPIOA)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE); //| RCC_APB2Periph_AFIO
RCC_APB2PeriphResetCmd(RCC_APB2Periph_GPIOA, DISABLE);
}
else if (port == GPIOB)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_GPIOB, DISABLE);
}
else if (port == GPIOC)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_GPIOC, DISABLE);
}
else if (port == GPIOD)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD, ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_GPIOD, DISABLE);
}
else if (port == GPIOE)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOE, ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_GPIOE, DISABLE);
}
else if (port == GPIOF)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOF, ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_GPIOF, DISABLE);
}
else
{
if (port == GPIOG)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOG, ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_GPIOG, DISABLE);
}
}
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = pinNum;
GPIO_InitStructure.GPIO_Mode = mode;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(port, &GPIO_InitStructure);
}
//------------------------------------------------------------------------------------------
void USART1_Config(void)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA,ENABLE);
GPIO_InitTypeDef initGPIO;
// Enable USART1 clock and release reset.
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1,ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_USART1,DISABLE);
/* Configure the GPIO ports( USART1 Transmit and Receive Lines) */
/* Configure the USART1_Tx as Alternate function Push-Pull */
GPIO_StructInit(&initGPIO);
initGPIO.GPIO_Mode = GPIO_Mode_AF_PP;
initGPIO.GPIO_Pin = GPIO_Pin_9;
initGPIO.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &initGPIO);
/* Configure the USART1_Rx as input floating */
initGPIO.GPIO_Mode = GPIO_Mode_IN_FLOATING;
initGPIO.GPIO_Pin = GPIO_Pin_10 ;
GPIO_Init(GPIOA, &initGPIO);
/* USART1 configuration ------------------------------------------------------*/
/* USART1 configured as follow:
- BaudRate = 115200 baud
- Word Length = 8 Bits
- One Stop Bit
- No parity
- Hardware flow control disabled (RTS and CTS signals)
- Receive and transmit enabled
*/
USART_InitTypeDef initUSART;
initUSART.USART_BaudRate = 115200;
initUSART.USART_WordLength = USART_WordLength_8b;
initUSART.USART_StopBits = USART_StopBits_1;
initUSART.USART_Parity = USART_Parity_No;
initUSART.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
initUSART.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
/* Configure the USART1 */
USART_Init(USART1, &initUSART);
/* Enable the USART1 */
USART_Cmd(USART1, ENABLE);
}
void encb_init( void )
{
TIM_ICInitTypeDef TIM_ICInitStructure;
//*********************************************************
//****** Main Encoder Setting
//*********************************************************
DBG( ENC, L, "Main encoder button init" );
RCC_APB2PeriphResetCmd( RCC_APB2Periph_TIM8, ENABLE );
TIM_ICInitStructure.TIM_Channel = TIM_Channel_1;
TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Falling;
TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI;
TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1;
TIM_ICInitStructure.TIM_ICFilter = ENCB_FILTER_CNT;
TIM_ICInit( TIM8, &TIM_ICInitStructure );
TIM_ICInitStructure.TIM_Channel = TIM_Channel_2;
TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Falling;
TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI;
TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1;
TIM_ICInitStructure.TIM_ICFilter = ENCB_FILTER_CNT;
TIM_ICInit( TIM8, &TIM_ICInitStructure );
TIM_EncoderInterfaceConfig( TIM8, TIM_EncoderMode_TI12,
TIM_ICPolarity_Falling, ENCB_MAIN_DIR_POL );
TIM_Cmd( TIM8, ENABLE );
bio_i_chk[ENCB_MAIN_A_PORT_IX].mask &= ~ENCB_MAIN_A_PIN;
bio_i_chk[ENCB_MAIN_B_PORT_IX].mask &= ~ENCB_MAIN_B_PIN;
//*********************************************************
//****** Initial Values Setting
//*********************************************************
encb_info[ENCB_IX_MAIN].pls_rev = 24;
encb_info[ENCB_IX_MAIN].val_min = 0;
encb_info[ENCB_IX_MAIN].val_max = 999 * 10;
encb_info[ENCB_IX_MAIN].val_cur = 123;
// encb_info[ENCB_IX_MAIN].val_cur = eep_data.c_ht_tgt;
encb_info[ENCB_IX_MAIN].sns_min = ENCB_BASE_SENS * 10;
encb_info[ENCB_IX_MAIN].sns_max = 25000;
} // end of encb_init()
int main(void)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC,ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_GPIOC,DISABLE);
GPIO_InitTypeDef gpio; //The GPIO_InitTypeDef structure can be referred by stm32f10x_gpio.h.
gpio.GPIO_Pin = GPIO_Pin_13;
gpio.GPIO_Speed = GPIO_Speed_50MHz;
gpio.GPIO_Mode = GPIO_Mode_Out_OD;
GPIO_Init(GPIOC,&gpio);
while (1)
{
GPIO_SetBits(GPIOC, GPIO_Pin_13); // LED ON
delay(10);
GPIO_ResetBits(GPIOC, GPIO_Pin_13); // LED OFF
delay(10);
}
}
/*************************************************************************
* Function Name: SPI1_Init
* Parameters: none
* Return: none
*
* Description: Init SPI1
*
*************************************************************************/
void SPI1_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
// Enable GPIO clock and release reset
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOC,
ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOC,
DISABLE);
// Configure LCD_CS GPIO Pin as push-pull output in high level
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Pin = LCD_CS_MASK;
GPIO_Init(LCD_CS_PORT, &GPIO_InitStructure);
GPIO_SetBits(LCD_CS_PORT,LCD_CS_MASK);
// Configure SPC1000_CS GPIO Pin as push-pull output in high level
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Pin = SCP1000_CS_MASK;
GPIO_Init(SCP1000_CS_PORT, &GPIO_InitStructure);
GPIO_SetBits(SCP1000_CS_PORT,SCP1000_CS_MASK);
// Configure SPI1_SCLK and SPI1_MOSI GPIOs Pins as push-pull outputs
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Pin = SPI1_SCLK_MASK | SPI1_MOSI_MASK;
GPIO_Init(SPI1_PORT, &GPIO_InitStructure);
// Configure SPI1_MISO GPIO Pin as input floating
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_InitStructure.GPIO_Pin = SPI1_MISO_MASK;
GPIO_Init(SPI1_PORT, &GPIO_InitStructure);
for(Int32U i = 0; i < SPI1_LAST_DEV; i++)
{
_SPI_Dev[i].DataWidth = 8;
_SPI_Dev[i].Delay = 0;
_SPI_Dev[i].CPOL = 0;
_SPI_Dev[i].CPHA = 0;
}
}
/*************************************************************************
* Function Name: Serial_Init
* Description: Init USARTs
*************************************************************************/
void Serial_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_USART1, ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_USART1, DISABLE);
/* Configure USART1 Tx (PA.09) as alternate function push-pull */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
/* Configure USART1 Rx (PA.10) as input floating */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
/* USART1 configuration ------------------------------------------------------*/
// USART1 configured as follow:
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
/* Configure the USART1 */
USART_Init(USART1, &USART_InitStructure);
/* Enable the USART Transmoit interrupt: this interrupt is generated when the
USART1 transmit data register is empty */
USART_ITConfig(USART1, USART_IT_TXE, ENABLE);
/* Enable the USART Receive interrupt: this interrupt is generated when the
USART1 receive data register is not empty */
USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);
/* Enable USART1 */
USART_Cmd(USART1, ENABLE);
}
/*************************************************************************
* Function Name: USB_HwInit
* Parameters: none
*
* Return: none
*
* Description: Init USB
*
*************************************************************************/
void USB_HwInit(void)
{
NVIC_InitTypeDef NVIC_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
// Reset USB Engine
RCC_APB1PeriphResetCmd(RCC_APB1Periph_USB,ENABLE);
// Init USB Clock
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USB,ENABLE);
// Release reset USB Engine
RCC_APB1PeriphResetCmd(RCC_APB1Periph_USB,DISABLE);
// Enable 48MHz clock
RCC_USBCLKConfig(USB_DIVIDER);
// Force USB Reset & Disable USB interrupts
USB_CNTR = 1;
// GPIO assign to the USB engine
RCC_APB2PeriphResetCmd( RCC_APB2Periph_GPIOA
| RCC_APB2Periph_GPIOC
| RCC_APB2Periph_AFIO, DISABLE);
RCC_APB2PeriphClockCmd( RCC_APB2Periph_GPIOA
| RCC_APB2Periph_GPIOC
| RCC_APB2Periph_AFIO, ENABLE);
GPIO_PinRemapConfig(GPIO_Remap1_CAN1,ENABLE); // xxx
// Configure PA11, PA12 as USB lines
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11 | GPIO_Pin_12;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// Configure PC11 USB connect.
GPIO_WriteBit(GPIOC,GPIO_Pin_11,Bit_SET);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOC, &GPIO_InitStructure);
// Disconnect device
USB_ConnectRes(FALSE);
// Init controls endpoints
USB_HwReset();
// Clear spurious pending interrupt
USB_ISTR = 0;
// USB interrupt connect to NVIC
#if USB_HIGH_PRIORITY_EVENT > 0
NVIC_InitStructure.NVIC_IRQChannel = USB_HP_CAN1_TX_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = USB_INTR_HIGH_PRIORITY;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
#endif // USB_HIGH_PRIORITY_EVENT > 0
NVIC_InitStructure.NVIC_IRQChannel = USB_LP_CAN1_RX0_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = USB_INTR_LOW_PRIORITY;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
}
/**
* @brief Deinitializes the SDIO peripheral registers to their default reset values.
* @param None
* @retval None
*/
void SDIO_DeInit(void)
{
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SDIO, ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SDIO, DISABLE);
}
/*************************************************************************
* Function Name: MmcInit
* Parameters: none
* Return: none
*
* Description: Init SPI, Cart Present, Write Protect and Chip select pins
*
*************************************************************************/
void MmcInit (void)
{
SPI_InitTypeDef SPI_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
// Enable GPIO clocks
RCC_APB2PeriphClockCmd( RCC_APB2Periph_GPIOB | RCC_APB2Periph_GPIOC, ENABLE);
// Enable SPI2 Periphery clock
RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI2, ENABLE);
// Deinitializes the SPI2
SPI_DeInit(SPI2);
// Release reset of GPIOB, GPIOC
RCC_APB2PeriphResetCmd( RCC_APB2Periph_GPIOB
| RCC_APB2Periph_GPIOC, DISABLE);
// Configure SPI2_CLK, SPI2_MOSI, SPI2_nCS1, Card Present and Write Protect pins
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Pin = SD_CS;
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Pin = SD_SCLK | SD_MOSI | SD_MISO;
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_InitStructure.GPIO_Pin = SD_CP | SD_WP;
GPIO_Init(GPIOC, &GPIO_InitStructure);
// Chip select
MmcChipSelect(0);
// Spi init
SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex;
SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b;
SPI_InitStructure.SPI_CPOL = SPI_CPOL_Low;
SPI_InitStructure.SPI_CPHA = SPI_CPHA_1Edge;
SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;
SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_256;
SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;
SPI_InitStructure.SPI_CRCPolynomial = 7;
SPI_Init(SPI2, &SPI_InitStructure);
// Enable SPI2 */
SPI_Cmd(SPI2, ENABLE);
// Clock Freq. Identification Mode < 400kHz
MmcSetClockFreq(IdentificationModeClock);
#if SPI_DMA_ENA > 0
// Enable DMA clock
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA, ENABLE);
// Clear pending interrupt
DMA_ClearITPendingBit( DMA_IT_GL4
| DMA_IT_GL5);
// Interrupts DMA enable
SPI_DMACmd(SPI2,SPI_DMAReq_Rx,DISABLE);
SPI_DMACmd(SPI2,SPI_DMAReq_Tx,DISABLE);
#ifndef DMA_ERRATA
NVIC_InitTypeDef NVIC_InitStructure;
// VIC configuration
NVIC_InitStructure.NVIC_IRQChannel = DMAChannel4_IRQChannel;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = SPI_DMA_INTR_PRIO;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
NVIC_InitStructure.NVIC_IRQChannel = DMAChannel5_IRQChannel;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = SPI_DMA_INTR_PRIO;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
#endif
#endif // SPI_DMA_ENA > 0
}
/*************************************************************************
* Function Name: UartInit
* Parameters: Int32U IrqSlot
*
* Return: Boolean
*
* Description: Init UART
*
*************************************************************************/
Boolean UartInit(UartNum_t Uart,Int32U IrqSlot)
{
volatile Int8U Tmp;
USART_InitTypeDef UART_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
USART_StructInit(&UART_InitStructure);
UART_InitStructure.USART_Parity = USART_Parity_No;
switch(Uart)
{
case UART_1:
pUart1RxFifo = (pUartFifo_t)malloc(sizeof(UartFifo_t));
if(pUart1RxFifo == NULL)
{
return(FALSE);
}
pUart1TxFifo = (pUartFifo_t)malloc(sizeof(UartFifo_t));
if(pUart1TxFifo == NULL)
{
free(pUart1RxFifo);
return(FALSE);
}
// Init receive and transmit FIFOs
pUart1RxFifo->PopIndx = pUart1RxFifo->PushIndx = \
pUart1TxFifo->PopIndx = pUart1TxFifo->PushIndx = 0;
// Release reset and enable clock
USART_DeInit(USART1);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
// GPIO Init
// Enable GPIO clock and release reset
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA,
ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_GPIOA,
DISABLE);
GPIO_PinRemapConfig(GPIO_Remap_USART1,DISABLE);
// Assign PA9 to UART1 (Tx)
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// Assign PA10 to UART1 (Rx)
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// Init UART1
USART_Init(USART1,&UART_InitStructure);
// Enable and configure the priority of the UART1 Update IRQ Channel
NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQChannel;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = UART1_INTR_PRI;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
USART_ClearFlag(USART1, USART_FLAG_CTS | USART_FLAG_LBD | USART_FLAG_TXE |
USART_FLAG_TC | USART_FLAG_RXNE | USART_FLAG_IDLE |
USART_FLAG_ORE | USART_FLAG_NE | USART_FLAG_FE |
USART_FLAG_PE);
// Enable UART1 interrupts
USART_ITConfig(USART1,USART_IT_PE ,ENABLE);
USART_ITConfig(USART1,USART_IT_TC ,DISABLE);
USART_ITConfig(USART1,USART_IT_RXNE,ENABLE);
USART_ITConfig(USART1,USART_IT_IDLE,DISABLE);
USART_ITConfig(USART1,USART_IT_LBD ,DISABLE);
USART_ITConfig(USART1,USART_IT_CTS ,DISABLE);
USART_ITConfig(USART1,USART_IT_ERR ,DISABLE);
// Enable the UART1
USART_Cmd(USART1, ENABLE);
break;
case UART_2:
pUart2RxFifo = (pUartFifo_t)malloc(sizeof(UartFifo_t));
if(pUart2RxFifo == NULL)
{
return(FALSE);
}
pUart2TxFifo = (pUartFifo_t)malloc(sizeof(UartFifo_t));
if(pUart2TxFifo == NULL)
{
free(pUart2RxFifo);
return(FALSE);
}
// Init receive and transmit FIFOs
pUart2RxFifo->PopIndx = pUart2RxFifo->PushIndx = \
pUart2TxFifo->PopIndx = pUart2TxFifo->PushIndx = 0;
// Release reset and enable clock
USART_DeInit(USART2);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE);
// GPIO Init
// Enable GPIO clock and release reset
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA,
ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_GPIOA,
DISABLE);
GPIO_PinRemapConfig(GPIO_Remap_USART2,DISABLE);
// Assign PA2 to UART2 (Tx)
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// Assign PA3 to UART2 (Rx)
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// Init UART2
USART_Init(USART2,&UART_InitStructure);
// Enable and configure the priority of the UART2 Update IRQ Channel
NVIC_InitStructure.NVIC_IRQChannel = USART2_IRQChannel;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = UART2_INTR_PRI;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
USART_ClearFlag(USART2, USART_FLAG_CTS | USART_FLAG_LBD | USART_FLAG_TXE |
USART_FLAG_TC | USART_FLAG_RXNE | USART_FLAG_IDLE |
USART_FLAG_ORE | USART_FLAG_NE | USART_FLAG_FE |
USART_FLAG_PE);
// Enable UART2 interrupts
USART_ITConfig(USART2,USART_IT_PE ,ENABLE);
USART_ITConfig(USART2,USART_IT_TXE ,ENABLE);
USART_ITConfig(USART2,USART_IT_TC ,DISABLE);
USART_ITConfig(USART2,USART_IT_RXNE,ENABLE);
USART_ITConfig(USART2,USART_IT_IDLE,DISABLE);
USART_ITConfig(USART2,USART_IT_LBD ,DISABLE);
USART_ITConfig(USART2,USART_IT_CTS ,DISABLE);
USART_ITConfig(USART2,USART_IT_ERR ,DISABLE);
// Enable the UART2
USART_Cmd(USART2, ENABLE);
break;
case UART_3:
pUart3RxFifo = (pUartFifo_t)malloc(sizeof(UartFifo_t));
if(pUart3RxFifo == NULL)
{
return(FALSE);
}
pUart3TxFifo = (pUartFifo_t)malloc(sizeof(UartFifo_t));
if(pUart3TxFifo == NULL)
{
free(pUart3RxFifo);
return(FALSE);
}
// Init receive and transmit FIFOs
pUart3RxFifo->PopIndx = pUart3RxFifo->PushIndx = \
pUart3TxFifo->PopIndx = pUart3TxFifo->PushIndx = 0;
// Release reset and enable clock
USART_DeInit(USART3);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE);
// GPIO Init
// Enable GPIO clock and release reset
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC | RCC_APB2Periph_AFIO,
ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_GPIOC | RCC_APB2Periph_AFIO,
DISABLE);
GPIO_PinRemapConfig(GPIO_PartialRemap_USART3,ENABLE);
// Assign PC10 to UART3 (Tx)
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_Init(GPIOC, &GPIO_InitStructure);
// Assign PC11 to UART3 (Rx)
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;
GPIO_Init(GPIOC, &GPIO_InitStructure);
// Init UART3
USART_Init(USART3,&UART_InitStructure);
// Enable and configure the priority of the UART3 Update IRQ Channel
NVIC_InitStructure.NVIC_IRQChannel = USART3_IRQChannel;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = UART3_INTR_PRI;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
USART_ClearFlag(USART3, USART_FLAG_CTS | USART_FLAG_LBD | USART_FLAG_TXE |
USART_FLAG_TC | USART_FLAG_RXNE | USART_FLAG_IDLE |
USART_FLAG_ORE | USART_FLAG_NE | USART_FLAG_FE |
USART_FLAG_PE);
// Enable UART3 interrupts
USART_ITConfig(USART3,USART_IT_PE ,ENABLE);
USART_ITConfig(USART3,USART_IT_TXE ,DISABLE);
USART_ITConfig(USART3,USART_IT_TC ,DISABLE);
USART_ITConfig(USART3,USART_IT_RXNE,ENABLE);
USART_ITConfig(USART3,USART_IT_IDLE,DISABLE);
USART_ITConfig(USART3,USART_IT_LBD ,DISABLE);
USART_ITConfig(USART3,USART_IT_CTS ,DISABLE);
USART_ITConfig(USART3,USART_IT_ERR ,DISABLE);
// Enable the UART3
USART_Cmd(USART3, ENABLE);
break;
default:
return(FALSE);
}
return(TRUE);
}
