void DBG_Init(void)
{
newlines = 0;
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
ROM_UARTConfigSetExpClk(UART0_BASE, ROM_SysCtlClockGet(), DBG_BAUD, UART_CFG_8N1);
ROM_UARTFIFOLevelSet(UART0_BASE, UART_FIFO_TX1_8, UART_FIFO_RX7_8);
ROM_IntEnable(INT_UART0);
ROM_UARTIntEnable(UART0_BASE, UART_INT_TX | UART_INT_RX | UART_INT_RT);
} // DBG_Init()
/**
* Configuring the UART console
*/
int uart_init(uart_t uart, uint32_t baudrate, uart_rx_cb_t rx_cb, uart_tx_cb_t tx_cb, void *arg)
{
/* Check the arguments */
assert(uart == 0);
/* Check to make sure the UART peripheral is present */
if(!ROM_SysCtlPeripheralPresent(SYSCTL_PERIPH_UART0)){
return -1;
}
int res = uart_init_blocking(uart, baudrate);
if(res < 0){
return res;
}
/* save callbacks */
config[uart].rx_cb = rx_cb;
config[uart].tx_cb = tx_cb;
config[uart].arg = arg;
/* ulBase = g_ulUARTBase[uart]; */
switch (uart){
#if UART_0_EN
case UART_0:
NVIC_SetPriority(UART_0_IRQ_CHAN, UART_IRQ_PRIO);
ROM_UARTTxIntModeSet(UART0_BASE, UART_TXINT_MODE_EOT);
ROM_UARTFIFOLevelSet(UART0_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
ROM_UARTFIFOEnable(UART0_BASE);
/* Enable the UART interrupt */
NVIC_EnableIRQ(UART_0_IRQ_CHAN);
/* Enable RX interrupt */
UART0_IM_R = UART_IM_RXIM | UART_IM_RTIM;
break;
#endif
#if UART_1_EN
case UART_1:
NVIC_SetPriority(UART_1_IRQ_CHAN, UART_IRQ_PRIO);
/* Enable the UART interrupt */
NVIC_EnableIRQ(UART_1_IRQ_CHAN);
break;
#endif
}
return 0;
}
void
HardwareSerial::begin(unsigned long baud)
{
baudRate = baud;
//
// Initialize the UART.
//
ROM_SysCtlPeripheralEnable(g_ulUARTPeriph[uartModule]);
//TODO:Add functionality for PinConfigure with variable uartModule
ROM_GPIOPinConfigure(g_ulUARTConfig[uartModule][0]);
ROM_GPIOPinConfigure(g_ulUARTConfig[uartModule][1]);
ROM_GPIOPinTypeUART(g_ulUARTPort[uartModule], g_ulUARTPins[uartModule]);
ROM_UARTConfigSetExpClk(UART_BASE, F_CPU, baudRate,
(UART_CONFIG_PAR_NONE | UART_CONFIG_STOP_ONE |
UART_CONFIG_WLEN_8));
//
// Set the UART to interrupt whenever the TX FIFO is almost empty or
// when any character is received.
//
ROM_UARTFIFOLevelSet(UART_BASE, UART_FIFO_TX1_8, UART_FIFO_RX1_8);
flushAll();
ROM_UARTIntDisable(UART_BASE, 0xFFFFFFFF);
ROM_UARTIntEnable(UART_BASE, UART_INT_RX | UART_INT_RT);
ROM_IntEnable(g_ulUARTInt[uartModule]);
//
// Enable the UART operation.
//
ROM_UARTEnable(UART_BASE);
// Allocate TX & RX buffers
if (txBuffer != (unsigned char *)0xFFFFFFFF) // Catch attempts to re-init this Serial instance by freeing old buffer first
free(txBuffer);
if (rxBuffer != (unsigned char *)0xFFFFFFFF) // Catch attempts to re-init this Serial instance by freeing old buffer first
free(rxBuffer);
txBuffer = (unsigned char *) malloc(txBufferSize);
rxBuffer = (unsigned char *) malloc(rxBufferSize);
SysCtlDelay(100);
}
void wiz610_init(void)
{
ROM_SysCtlPeripheralEnable(WIZ610_GPIO_PERIPH);
ROM_GPIODirModeSet(WIZ610_GPIO_BASE,WIZ610_GPIO_PIN_CMD_ENABLE ,GPIO_DIR_MODE_OUT);
ROM_GPIOPadConfigSet(WIZ610_GPIO_BASE,WIZ610_GPIO_PIN_CMD_ENABLE,GPIO_STRENGTH_8MA,GPIO_PIN_TYPE_STD_WPU);
ROM_GPIOPinWrite(WIZ610_GPIO_BASE,WIZ610_GPIO_PIN_CMD_ENABLE,WIZ610_GPIO_PIN_CMD_ENABLE);
// uart setup
ROM_SysCtlPeripheralEnable(WIZ610_UART_PERIPH);
ROM_GPIOPinConfigure(GPIO_PB0_U1RX);
ROM_GPIOPinConfigure(GPIO_PB1_U1TX);
ROM_GPIOPinTypeUART(WIZ610_GPIO_BASE, WIZ610_GPIO_PIN_RX | WIZ610_GPIO_PIN_TX);
ROM_UARTConfigSetExpClk(WIZ610_UART_BASE, ROM_SysCtlClockGet(), 38400,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |
UART_CONFIG_PAR_NONE));
ROM_GPIOPinWrite(WIZ610_GPIO_BASE,WIZ610_GPIO_PIN_CMD_ENABLE,0);
ROM_UARTFIFOLevelSet(WIZ610_UART_BASE, UART_FIFO_TX4_8, UART_FIFO_RX1_8);
ROM_IntEnable(INT_UART1);
ROM_UARTEnable(WIZ610_UART_BASE);
ROM_UARTDMAEnable(WIZ610_UART_BASE, UART_DMA_TX);
ROM_UARTIntEnable(WIZ610_UART_BASE, UART_INT_RX);
ROM_IntEnable(INT_UDMA);
cmd_modbus_switch=1;
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
uint32_t ui32TxCount;
uint32_t ui32RxCount;
tRectangle sRect;
char pcBuffer[16];
uint32_t ui32Fullness;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Configure the required pins for USB operation.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
ROM_GPIOPinConfigure(GPIO_PG4_USB0EPEN);
ROM_GPIOPinTypeUSBDigital(GPIO_PORTG_BASE, GPIO_PIN_4);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Erratum workaround for silicon revision A1. VBUS must have pull-down.
//
if(CLASS_IS_BLIZZARD && REVISION_IS_A1)
{
HWREG(GPIO_PORTB_BASE + GPIO_O_PDR) |= GPIO_PIN_1;
}
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sCFAL96x64x16);
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.i16YMax = 9;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_psFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb-dev-serial", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 4, 0);
//
// Show the various static text elements on the color STN display.
//
GrStringDraw(&g_sContext, "Tx #",-1, 0, 12, false);
GrStringDraw(&g_sContext, "Tx buf", -1, 0, 22, false);
GrStringDraw(&g_sContext, "Rx #", -1, 0, 32, false);
GrStringDraw(&g_sContext, "Rx buf", -1, 0, 42, false);
DrawBufferMeter(&g_sContext, 40, 22);
DrawBufferMeter(&g_sContext, 40, 42);
//
// Enable the UART that we will be redirecting.
//
ROM_SysCtlPeripheralEnable(USB_UART_PERIPH);
//
// Enable and configure the UART RX and TX pins
//
ROM_SysCtlPeripheralEnable(TX_GPIO_PERIPH);
ROM_SysCtlPeripheralEnable(RX_GPIO_PERIPH);
ROM_GPIOPinTypeUART(TX_GPIO_BASE, TX_GPIO_PIN);
ROM_GPIOPinTypeUART(RX_GPIO_BASE, RX_GPIO_PIN);
//
// TODO: Add code to configure handshake GPIOs if required.
//
//
// Set the default UART configuration.
//
ROM_UARTConfigSetExpClk(USB_UART_BASE, ROM_SysCtlClockGet(),
DEFAULT_BIT_RATE, DEFAULT_UART_CONFIG);
ROM_UARTFIFOLevelSet(USB_UART_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
//
// Configure and enable UART interrupts.
//
ROM_UARTIntClear(USB_UART_BASE, ROM_UARTIntStatus(USB_UART_BASE, false));
ROM_UARTIntEnable(USB_UART_BASE, (UART_INT_OE | UART_INT_BE | UART_INT_PE |
UART_INT_FE | UART_INT_RT | UART_INT_TX | UART_INT_RX));
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, " Configuring... ");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDCDCInit(0, &g_sCDCDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, "Waiting for host");
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Enable interrupts now that the application is ready to start.
//
ROM_IntEnable(USB_UART_INT);
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ui32Flags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
ROM_IntMasterDisable();
g_ui32Flags &= ~COMMAND_STATUS_UPDATE;
ROM_IntMasterEnable();
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32UARTTxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32UARTTxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, "%d ", ui32TxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 40, 12, true);
//
// Update the RX buffer fullness. Remember that the buffers are
// named relative to the USB whereas the status display is from
// the UART's perspective. The USB's receive buffer is the UART's
// transmit buffer.
//
ui32Fullness = ((USBBufferDataAvailable(&g_sRxBuffer) * 100) /
UART_BUFFER_SIZE);
UpdateBufferMeter(&g_sContext, ui32Fullness, 40, 22);
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32UARTRxCount)
{
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32UARTRxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, "%d ", ui32RxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 40, 32, true);
//
// Update the TX buffer fullness. Remember that the buffers are
// named relative to the USB whereas the status display is from
// the UART's perspective. The USB's transmit buffer is the UART's
// receive buffer.
//
ui32Fullness = ((USBBufferDataAvailable(&g_sTxBuffer) * 100) /
UART_BUFFER_SIZE);
UpdateBufferMeter(&g_sContext, ui32Fullness, 40, 42);
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
uint32_t ui32TxCount, ui32RxCount, ui32Fullness, ui32SysClock, ui32PLLRate;
tRectangle sRect;
char pcBuffer[16];
#ifdef USE_ULPI
uint32_t ui32Setting;
#endif
//
// Set the system clock to run at 120MHz from the PLL.
//
ui32SysClock = MAP_SysCtlClockFreqSet((SYSCTL_XTAL_25MHZ |
SYSCTL_OSC_MAIN | SYSCTL_USE_PLL |
SYSCTL_CFG_VCO_480), 120000000);
//
// Configure the device pins.
//
PinoutSet();
#ifdef USE_ULPI
//
// Switch the USB ULPI Pins over.
//
USBULPIPinoutSet();
//
// Enable USB ULPI with high speed support.
//
ui32Setting = USBLIB_FEATURE_ULPI_HS;
USBOTGFeatureSet(0, USBLIB_FEATURE_USBULPI, &ui32Setting);
//
// Setting the PLL frequency to zero tells the USB library to use the
// external USB clock.
//
ui32PLLRate = 0;
#else
//
// Save the PLL rate used by this application.
//
ui32PLLRate = 480000000;
#endif
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ui32SysClock / TICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Not configured initially.
//
g_ui32Flags = 0;
//
// Initialize the display driver.
//
Kentec320x240x16_SSD2119Init(ui32SysClock);
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sKentec320x240x16_SSD2119);
//
// Draw the application frame.
//
FrameDraw(&g_sContext, "usb-dev-serial");
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.i16YMax = 23;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Show the various static text elements on the color STN display.
//
GrContextFontSet(&g_sContext, TEXT_FONT);
GrStringDraw(&g_sContext, "Tx bytes:", -1, 8, 80, false);
GrStringDraw(&g_sContext, "Tx buffer:", -1, 8, 105, false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, 8, 160, false);
GrStringDraw(&g_sContext, "Rx buffer:", -1, 8, 185, false);
DrawBufferMeter(&g_sContext, 150, 105);
DrawBufferMeter(&g_sContext, 150, 185);
//
// Enable the UART that we will be redirecting.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
//
// Change the UART clock to the 16 MHz PIOSC.
//
UARTClockSourceSet(UART0_BASE, UART_CLOCK_PIOSC);
//
// Set the default UART configuration.
//
ROM_UARTConfigSetExpClk(UART0_BASE, UART_CLOCK,
DEFAULT_BIT_RATE, DEFAULT_UART_CONFIG);
ROM_UARTFIFOLevelSet(UART0_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
//
// Configure and enable UART interrupts.
//
ROM_UARTIntClear(UART0_BASE, ROM_UARTIntStatus(UART0_BASE, false));
ROM_UARTIntEnable(UART0_BASE, (UART_INT_OE | UART_INT_BE | UART_INT_PE |
UART_INT_FE | UART_INT_RT | UART_INT_TX | UART_INT_RX));
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, " Configuring USB... ");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeDevice, 0);
//
// Tell the USB library the CPU clock and the PLL frequency. This is a
// new requirement for TM4C129 devices.
//
USBDCDFeatureSet(0, USBLIB_FEATURE_CPUCLK, &ui32SysClock);
USBDCDFeatureSet(0, USBLIB_FEATURE_USBPLL, &ui32PLLRate);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDCDCInit(0, (tUSBDCDCDevice *)&g_sCDCDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, " Waiting for host... ");
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
g_ui32UARTTxCount = 0;
g_ui32UARTRxCount = 0;
#ifdef DEBUG
g_ui32UARTRxErrors = 0;
#endif
//
// Enable interrupts now that the application is ready to start.
//
ROM_IntEnable(INT_UART0);
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(HWREGBITW(&g_ui32Flags, FLAG_STATUS_UPDATE))
{
//
// Clear the command flag
//
HWREGBITW(&g_ui32Flags, FLAG_STATUS_UPDATE) = 0;
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32UARTTxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32UARTTxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, "%d ", ui32TxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 150, 80, true);
//
// Update the RX buffer fullness. Remember that the buffers are
// named relative to the USB whereas the status display is from
// the UART's perspective. The USB's receive buffer is the UART's
// transmit buffer.
//
ui32Fullness = ((USBBufferDataAvailable(&g_sRxBuffer) * 100) /
UART_BUFFER_SIZE);
UpdateBufferMeter(&g_sContext, ui32Fullness, 150, 105);
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32UARTRxCount)
{
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32UARTRxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, "%d ", ui32RxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 150, 160, true);
//
// Update the TX buffer fullness. Remember that the buffers are
// named relative to the USB whereas the status display is from
// the UART's perspective. The USB's transmit buffer is the UART's
// receive buffer.
//
ui32Fullness = ((USBBufferDataAvailable(&g_sTxBuffer) * 100) /
UART_BUFFER_SIZE);
UpdateBufferMeter(&g_sContext, ui32Fullness, 150, 185);
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
uint32_t ui32TxCount;
uint32_t ui32RxCount;
//uint32_t ui32Loop;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
#if 1
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Configure the required pins for USB operation.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_5 | GPIO_PIN_4);
//ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / 100);
/* This code taken from: http://e2e.ti.com/support/microcontrollers/tiva_arm/f/908/t/311237.aspx
*/
#else
#include "hw_nvic.h"
FlashErase(0x00000000);
ROM_IntMasterDisable();
ROM_SysTickIntDisable();
ROM_SysTickDisable();
uint32_t ui32SysClock;
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ);
ui32SysClock = ROM_SysCtlClockGet();
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_4 | GPIO_PIN_5);
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / 100);
HWREG(NVIC_DIS0) = 0xffffffff;
HWREG(NVIC_DIS1) = 0xffffffff;
HWREG(NVIC_DIS2) = 0xffffffff;
HWREG(NVIC_DIS3) = 0xffffffff;
HWREG(NVIC_DIS4) = 0xffffffff;
int ui32Addr;
for(ui32Addr = NVIC_PRI0; ui32Addr <= NVIC_PRI34; ui32Addr+=4)
{
HWREG(ui32Addr) = 0;
}
HWREG(NVIC_SYS_PRI1) = 0;
HWREG(NVIC_SYS_PRI2) = 0;
HWREG(NVIC_SYS_PRI3) = 0;
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
ROM_SysCtlPeripheralReset(SYSCTL_PERIPH_USB0);
ROM_SysCtlUSBPLLEnable();
ROM_SysCtlDelay(ui32SysClock*2 / 3);
ROM_IntMasterEnable();
ROM_UpdateUSB(0);
while(1)
{
}
#endif
#define BOOTLOADER_TEST 0
#if BOOTLOADER_TEST
#include "hw_nvic.h"
//ROM_UpdateUART();
// May need to do the following here:
// 0. See if this will cause bootloader to start
//ROM_FlashErase(0);
//ROM_UpdateUSB(0);
#define SYSTICKS_PER_SECOND 100
uint32_t ui32SysClock = ROM_SysCtlClockGet();
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//USBDCDTerm(0);
// Disable all interrupts
ROM_IntMasterDisable();
ROM_SysTickIntDisable();
ROM_SysTickDisable();
HWREG(NVIC_DIS0) = 0xffffffff;
HWREG(NVIC_DIS1) = 0xffffffff;
HWREG(NVIC_DIS2) = 0xffffffff;
HWREG(NVIC_DIS3) = 0xffffffff;
HWREG(NVIC_DIS4) = 0xffffffff;
int ui32Addr;
for(ui32Addr = NVIC_PRI0; ui32Addr <= NVIC_PRI34; ui32Addr+=4)
{
HWREG(ui32Addr) = 0;
}
HWREG(NVIC_SYS_PRI1) = 0;
HWREG(NVIC_SYS_PRI2) = 0;
HWREG(NVIC_SYS_PRI3) = 0;
// 1. Enable USB PLL
//ROM_SysCtlUSBPLLEnable();
// 2. Enable USB controller
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
ROM_SysCtlPeripheralReset(SYSCTL_PERIPH_USB0);
//USBClockEnable(USB0_BASE, 8, USB_CLOCK_INTERNAL);
//HWREG(USB0_BASE + USB_O_CC) = (8 - 1) | USB_CLOCK_INTERNAL;
ROM_SysCtlUSBPLLEnable();
// 3. Enable USB D+ D- pins
// 4. Activate USB DFU
ROM_SysCtlDelay(ui32SysClock * 2 / 3);
ROM_IntMasterEnable(); // Re-enable interrupts at NVIC level
ROM_UpdateUSB(0);
// 5. Should never get here since update is in progress
#endif // BOOTLOADER_TEST
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB); // gjs Our board uses GPIOB for LEDs
// gjs original ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2 & PF3).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE, GPIO_PIN_0|GPIO_PIN_1);
// gjs original ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3|GPIO_PIN_2);
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Enable the UART that we will be redirecting.
//
ROM_SysCtlPeripheralEnable(USB_UART_PERIPH);
//
// Enable and configure the UART RX and TX pins
//
ROM_SysCtlPeripheralEnable(TX_GPIO_PERIPH);
ROM_SysCtlPeripheralEnable(RX_GPIO_PERIPH);
ROM_GPIOPinTypeUART(TX_GPIO_BASE, TX_GPIO_PIN);
ROM_GPIOPinTypeUART(RX_GPIO_BASE, RX_GPIO_PIN);
//
// TODO: Add code to configure handshake GPIOs if required.
//
//
// Set the default UART configuration.
//
ROM_UARTConfigSetExpClk(USB_UART_BASE, ROM_SysCtlClockGet(),
DEFAULT_BIT_RATE, DEFAULT_UART_CONFIG);
ROM_UARTFIFOLevelSet(USB_UART_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
//
// Configure and enable UART interrupts.
//
ROM_UARTIntClear(USB_UART_BASE, ROM_UARTIntStatus(USB_UART_BASE, false));
ROM_UARTIntEnable(USB_UART_BASE, (UART_INT_OE | UART_INT_BE | UART_INT_PE |
UART_INT_FE | UART_INT_RT | UART_INT_TX | UART_INT_RX));
//
// Enable the system tick.
//
#if 0
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
#endif
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDCDCInit(0, &g_sCDCDevice);
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Enable interrupts now that the application is ready to start.
//
ROM_IntEnable(USB_UART_INT);
// Enable FreeRTOS
mainA(); // FreeRTOS. Will not return
#if 0
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ui32Flags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
ROM_IntMasterDisable();
g_ui32Flags &= ~COMMAND_STATUS_UPDATE;
ROM_IntMasterEnable();
}
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32UARTTxCount)
{
//
// Turn on the Green LED.
//
// gjs ROM_UARTCharPutNonBlocking(USB_UART_BASE, 'b');
#if 1
if (ui32TxCount & 1) {
GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_0, GPIO_PIN_0);
} else {
GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_0, 0);
}
#else
if (1 || g_ui32UARTTxCount & 0x01) {
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, GPIO_PIN_3);
} else {
//GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, 0);
}
//
// Delay for a bit.
//
for(uint32_t ui32Loop = 0; ui32Loop < 150000; ui32Loop++)
{
}
//
// Turn off the Green LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, 0);
#endif
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32UARTTxCount;
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32UARTRxCount)
{
//
// Turn on the Blue LED.
//
#if 1
if (ui32RxCount & 1) {
GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_1, GPIO_PIN_1);
} else {
GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_1, 0);
}
#else
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, GPIO_PIN_2);
//
// Delay for a bit.
//
for(uint32_t ui32Loop = 0; ui32Loop < 150000; ui32Loop++)
{
}
//
// Turn off the Blue LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, 0);
#endif
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32UARTRxCount;
}
}
#endif
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the UART.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
//
// Enable and configure the UART RX and TX pins
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Set the default UART configuration.
//
ROM_UARTConfigSetExpClk(UART0_BASE, ROM_SysCtlClockGet(), 115200,
UART_CONFIG_WLEN_8 | UART_CONFIG_PAR_NONE |
UART_CONFIG_STOP_ONE);
ROM_UARTFIFOLevelSet(UART0_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
//
// Configure and enable UART interrupts.
//
ROM_UARTIntClear(UART0_BASE, ROM_UARTIntStatus(UART0_BASE, false));
ROM_UARTIntEnable(UART0_BASE, (UART_INT_OE | UART_INT_BE | UART_INT_PE |
UART_INT_FE | UART_INT_RT | UART_INT_RX));
//
// Enable and configure the user LED pin.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTD_BASE, GPIO_PIN_0);
//
// Turn off the user LED.
//
GPIOPinWrite(GPIO_PORTD_BASE, GPIO_PIN_0, 0);
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, USB_MODE_DEVICE, 0);
//
// Pass the device information to the USB library and place the device
// on the bus.
//
USBDCDCInit(0, &g_sCDCDevice);
//
// Enable interrupts now that the application is ready to start.
//
ROM_IntEnable(INT_UART0);
//
// Main application loop.
//
while(1)
{
}
}
//*****************************************************************************
//
// Initializes the UART0 peripheral and sets up the TX and RX uDMA channels.
// The UART is configured for loopback mode so that any data sent on TX will be
// received on RX. The uDMA channels are configured so that the TX channel
// will copy data from a buffer to the UART TX output. And the uDMA RX channel
// will receive any incoming data into a pair of buffers in ping-pong mode.
//
//*****************************************************************************
void
InitUART0Transfer(void)
{
unsigned int uIdx;
//
// Fill the TX buffer with a simple data pattern.
//
for(uIdx = 0; uIdx < UART_TXBUF_SIZE; uIdx++)
{
g_ucTxBuf[uIdx] = uIdx;
}
//
// Enable the UART peripheral, and configure it to operate even if the CPU
// is in sleep.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
//
// Configure the UART communication parameters.
//
ROM_UARTConfigSetExpClk(UART0_BASE, ROM_SysCtlClockGet(), 115200,
UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |
UART_CONFIG_PAR_NONE);
//
// Set both the TX and RX trigger thresholds to 4. This will be used by
// the uDMA controller to signal when more data should be transferred. The
// uDMA TX and RX channels will be configured so that it can transfer 4
// bytes in a burst when the UART is ready to transfer more data.
//
ROM_UARTFIFOLevelSet(UART0_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
//
// Enable the UART for operation, and enable the uDMA interface for both TX
// and RX channels.
//
ROM_UARTEnable(UART0_BASE);
ROM_UARTDMAEnable(UART0_BASE, UART_DMA_RX | UART_DMA_TX);
//
// This register write will set the UART to operate in loopback mode. Any
// data sent on the TX output will be received on the RX input.
//
HWREG(UART0_BASE + UART_O_CTL) |= UART_CTL_LBE;
//
// Enable the UART peripheral interrupts. Note that no UART interrupts
// were enabled, but the uDMA controller will cause an interrupt on the
// UART interrupt signal when a uDMA transfer is complete.
//
ROM_IntEnable(INT_UART0);
//
// Put the attributes in a known state for the uDMA UART0RX channel. These
// should already be disabled by default.
//
ROM_uDMAChannelAttributeDisable(UDMA_CHANNEL_UART0RX,
UDMA_ATTR_ALTSELECT | UDMA_ATTR_USEBURST |
UDMA_ATTR_HIGH_PRIORITY |
UDMA_ATTR_REQMASK);
//
// Configure the control parameters for the primary control structure for
// the UART RX channel. The primary contol structure is used for the "A"
// part of the ping-pong receive. The transfer data size is 8 bits, the
// source address does not increment since it will be reading from a
// register. The destination address increment is byte 8-bit bytes. The
// arbitration size is set to 4 to match the RX FIFO trigger threshold.
// The uDMA controller will use a 4 byte burst transfer if possible. This
// will be somewhat more effecient that single byte transfers.
//
ROM_uDMAChannelControlSet(UDMA_CHANNEL_UART0RX | UDMA_PRI_SELECT,
UDMA_SIZE_8 | UDMA_SRC_INC_NONE | UDMA_DST_INC_8 |
UDMA_ARB_4);
//
// Configure the control parameters for the alternate control structure for
// the UART RX channel. The alternate contol structure is used for the "B"
// part of the ping-pong receive. The configuration is identical to the
// primary/A control structure.
//
ROM_uDMAChannelControlSet(UDMA_CHANNEL_UART0RX | UDMA_ALT_SELECT,
UDMA_SIZE_8 | UDMA_SRC_INC_NONE | UDMA_DST_INC_8 |
UDMA_ARB_4);
//
// Set up the transfer parameters for the UART RX primary control
// structure. The mode is set to ping-pong, the transfer source is the
// UART data register, and the destination is the receive "A" buffer. The
// transfer size is set to match the size of the buffer.
//
ROM_uDMAChannelTransferSet(UDMA_CHANNEL_UART0RX | UDMA_PRI_SELECT,
UDMA_MODE_PINGPONG,
(void *)(UART0_BASE + UART_O_DR),
g_ucRxBufA, sizeof(g_ucRxBufA));
//
// Set up the transfer parameters for the UART RX alternate control
// structure. The mode is set to ping-pong, the transfer source is the
// UART data register, and the destination is the receive "B" buffer. The
// transfer size is set to match the size of the buffer.
//
ROM_uDMAChannelTransferSet(UDMA_CHANNEL_UART0RX | UDMA_ALT_SELECT,
UDMA_MODE_PINGPONG,
(void *)(UART0_BASE + UART_O_DR),
g_ucRxBufB, sizeof(g_ucRxBufB));
//
// Put the attributes in a known state for the uDMA UART0TX channel. These
// should already be disabled by default.
//
ROM_uDMAChannelAttributeDisable(UDMA_CHANNEL_UART0TX,
UDMA_ATTR_ALTSELECT |
UDMA_ATTR_HIGH_PRIORITY |
UDMA_ATTR_REQMASK);
//
// Set the USEBURST attribute for the uDMA UART TX channel. This will
// force the controller to always use a burst when transferring data from
// the TX buffer to the UART. This is somewhat more effecient bus usage
// than the default which allows single or burst transfers.
//
ROM_uDMAChannelAttributeEnable(UDMA_CHANNEL_UART0TX, UDMA_ATTR_USEBURST);
//
// Configure the control parameters for the UART TX. The uDMA UART TX
// channel is used to transfer a block of data from a buffer to the UART.
// The data size is 8 bits. The source address increment is 8-bit bytes
// since the data is coming from a buffer. The destination increment is
// none since the data is to be written to the UART data register. The
// arbitration size is set to 4, which matches the UART TX FIFO trigger
// threshold.
//
ROM_uDMAChannelControlSet(UDMA_CHANNEL_UART0TX | UDMA_PRI_SELECT,
UDMA_SIZE_8 | UDMA_SRC_INC_8 | UDMA_DST_INC_NONE |
UDMA_ARB_4);
//
// Set up the transfer parameters for the uDMA UART TX channel. This will
// configure the transfer source and destination and the transfer size.
// Basic mode is used because the peripheral is making the uDMA transfer
// request. The source is the TX buffer and the destination is the UART
// data register.
//
ROM_uDMAChannelTransferSet(UDMA_CHANNEL_UART0TX | UDMA_PRI_SELECT,
UDMA_MODE_BASIC, g_ucTxBuf,
(void *)(UART0_BASE + UART_O_DR),
sizeof(g_ucTxBuf));
//
// Now both the uDMA UART TX and RX channels are primed to start a
// transfer. As soon as the channels are enabled, the peripheral will
// issue a transfer request and the data transfers will begin.
//
ROM_uDMAChannelEnable(UDMA_CHANNEL_UART0RX);
ROM_uDMAChannelEnable(UDMA_CHANNEL_UART0TX);
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
unsigned long ulTxCount;
unsigned long ulRxCount;
unsigned long ulLoop;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Configure the required pins for USB operation.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_5 | GPIO_PIN_4);
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2 & PF3).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3|GPIO_PIN_2);
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Enable the UART that we will be redirecting.
//
ROM_SysCtlPeripheralEnable(USB_UART_PERIPH);
//
// Enable and configure the UART RX and TX pins
//
ROM_SysCtlPeripheralEnable(TX_GPIO_PERIPH);
ROM_SysCtlPeripheralEnable(RX_GPIO_PERIPH);
ROM_GPIOPinTypeUART(TX_GPIO_BASE, TX_GPIO_PIN);
ROM_GPIOPinTypeUART(RX_GPIO_BASE, RX_GPIO_PIN);
//
// TODO: Add code to configure handshake GPIOs if required.
//
//
// Set the default UART configuration.
//
ROM_UARTConfigSetExpClk(USB_UART_BASE, ROM_SysCtlClockGet(),
DEFAULT_BIT_RATE, DEFAULT_UART_CONFIG);
ROM_UARTFIFOLevelSet(USB_UART_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
//
// Configure and enable UART interrupts.
//
ROM_UARTIntClear(USB_UART_BASE, ROM_UARTIntStatus(USB_UART_BASE, false));
ROM_UARTIntEnable(USB_UART_BASE, (UART_INT_OE | UART_INT_BE | UART_INT_PE |
UART_INT_FE | UART_INT_RT | UART_INT_TX | UART_INT_RX));
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Initialize the transmit and receive buffers.
//
USBBufferInit((tUSBBuffer *)&g_sTxBuffer);
USBBufferInit((tUSBBuffer *)&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, USB_MODE_DEVICE, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDCDCInit(0, (tUSBDCDCDevice *)&g_sCDCDevice);
//
// Clear our local byte counters.
//
ulRxCount = 0;
ulTxCount = 0;
//
// Enable interrupts now that the application is ready to start.
//
ROM_IntEnable(USB_UART_INT);
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ulFlags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
ROM_IntMasterDisable();
g_ulFlags &= ~COMMAND_STATUS_UPDATE;
ROM_IntMasterEnable();
}
//
// Has there been any transmit traffic since we last checked?
//
if(ulTxCount != g_ulUARTTxCount)
{
//
// Turn on the Green LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, GPIO_PIN_3);
//
// Delay for a bit.
//
for(ulLoop = 0; ulLoop < 150000; ulLoop++)
{
}
//
// Turn off the Green LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, 0);
//
// Take a snapshot of the latest transmit count.
//
ulTxCount = g_ulUARTTxCount;
}
//
// Has there been any receive traffic since we last checked?
//
if(ulRxCount != g_ulUARTRxCount)
{
//
// Turn on the Blue LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, GPIO_PIN_2);
//
// Delay for a bit.
//
for(ulLoop = 0; ulLoop < 150000; ulLoop++)
{
}
//
// Turn off the Blue LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, 0);
//
// Take a snapshot of the latest receive count.
//
ulRxCount = g_ulUARTRxCount;
}
}
}
