int rt28xx_init(
IN PRTMP_ADAPTER pAd,
IN PSTRING pDefaultMac,
IN PSTRING pHostName)
{
UINT index;
UCHAR TmpPhy;
NDIS_STATUS Status;
UINT32 MacCsr0 = 0;
#ifdef CONFIG_STA_SUPPORT
#ifdef PCIE_PS_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
// If dirver doesn't wake up firmware here,
// NICLoadFirmware will hang forever when interface is up again.
if (OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_DOZE) &&
OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_ADVANCE_POWER_SAVE_PCIE_DEVICE))
{
AUTO_WAKEUP_STRUC AutoWakeupCfg;
AsicForceWakeup(pAd, TRUE);
AutoWakeupCfg.word = 0;
RTMP_IO_WRITE32(pAd, AUTO_WAKEUP_CFG, AutoWakeupCfg.word);
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_DOZE);
}
}
#endif // PCIE_PS_SUPPORT //
#endif // CONFIG_STA_SUPPORT //
// reset Adapter flags
RTMP_CLEAR_FLAGS(pAd);
// Init BssTab & ChannelInfo tabbles for auto channel select.
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
AutoChBssTableInit(pAd);
ChannelInfoInit(pAd);
}
#endif // CONFIG_AP_SUPPORT //
#ifdef DOT11_N_SUPPORT
// Allocate BA Reordering memory
if (ba_reordering_resource_init(pAd, MAX_REORDERING_MPDU_NUM) != TRUE)
goto err1;
#endif // DOT11_N_SUPPORT //
// Make sure MAC gets ready.
index = 0;
do
{
RTMP_IO_READ32(pAd, MAC_CSR0, &MacCsr0);
pAd->MACVersion = MacCsr0;
if ((pAd->MACVersion != 0x00) && (pAd->MACVersion != 0xFFFFFFFF))
break;
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST))
goto err1;
RTMPusecDelay(10);
} while (index++ < 100);
DBGPRINT(RT_DEBUG_TRACE, ("MAC_CSR0 [ Ver:Rev=0x%08x]\n", pAd->MACVersion));
#ifdef RTMP_MAC_PCI
// To fix driver disable/enable hang issue when radio off
RTMP_IO_WRITE32(pAd, PWR_PIN_CFG, 0x2);
#endif // RTMP_MAC_PCI //
// Disable DMA
RT28XXDMADisable(pAd);
// Load 8051 firmware
Status = NICLoadFirmware(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICLoadFirmware failed, Status[=0x%08x]\n", Status));
goto err1;
}
NICLoadRateSwitchingParams(pAd);
// Disable interrupts here which is as soon as possible
// This statement should never be true. We might consider to remove it later
#ifdef RTMP_MAC_PCI
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_ACTIVE))
{
RTMP_ASIC_INTERRUPT_DISABLE(pAd);
}
#endif // RTMP_MAC_PCI //
#ifdef RESOURCE_PRE_ALLOC
Status = RTMPInitTxRxRingMemory(pAd);
#else
Status = RTMPAllocTxRxRingMemory(pAd);
#endif // RESOURCE_PRE_ALLOC //
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPAllocTxRxMemory failed, Status[=0x%08x]\n", Status));
goto err2;
}
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
// initialize MLME
//
Status = RtmpMgmtTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err3;
Status = MlmeInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MlmeInit failed, Status[=0x%08x]\n", Status));
goto err4;
}
#ifdef RMTP_RBUS_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoConfigInit(pAd);
#endif // VIDEO_TURBINE_SUPPORT //
#endif // RMTP_RBUS_SUPPORT //
// Initialize pAd->StaCfg, pAd->ApCfg, pAd->CommonCfg to manufacture default
//
UserCfgInit(pAd);
Status = RtmpNetTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err5;
// COPY_MAC_ADDR(pAd->ApCfg.MBSSID[apidx].Bssid, netif->hwaddr);
// pAd->bForcePrintTX = TRUE;
CfgInitHook(pAd);
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
APInitialize(pAd);
#endif // CONFIG_AP_SUPPORT //
#ifdef BLOCK_NET_IF
initblockQueueTab(pAd);
#endif // BLOCK_NET_IF //
Status = MeasureReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MeasureReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
Status = TpcReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("TpcReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
//
// Init the hardware, we need to init asic before read registry, otherwise mac register will be reset
//
Status = NICInitializeAdapter(pAd, TRUE);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICInitializeAdapter failed, Status[=0x%08x]\n", Status));
if (Status != NDIS_STATUS_SUCCESS)
goto err6;
}
// Read parameters from Config File
Status = RTMPReadParametersHook(pAd);
DBGPRINT(RT_DEBUG_OFF, ("1. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPReadParametersHook failed, Status[=0x%08x]\n",Status));
goto err6;
}
#ifdef DOT11_N_SUPPORT
//Init Ba Capability parameters.
// RT28XX_BA_INIT(pAd);
pAd->CommonCfg.DesiredHtPhy.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
pAd->CommonCfg.DesiredHtPhy.AmsduEnable = (USHORT)pAd->CommonCfg.BACapability.field.AmsduEnable;
pAd->CommonCfg.DesiredHtPhy.AmsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.DesiredHtPhy.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
// UPdata to HT IE
pAd->CommonCfg.HtCapability.HtCapInfo.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
pAd->CommonCfg.HtCapability.HtCapInfo.AMsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.HtCapability.HtCapParm.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
#endif // DOT11_N_SUPPORT //
// after reading Registry, we now know if in AP mode or STA mode
// Load 8051 firmware; crash when FW image not existent
// Status = NICLoadFirmware(pAd);
// if (Status != NDIS_STATUS_SUCCESS)
// break;
DBGPRINT(RT_DEBUG_OFF, ("2. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
// We should read EEPROM for all cases. rt2860b
NICReadEEPROMParameters(pAd, (PUCHAR)pDefaultMac);
#ifdef CONFIG_STA_SUPPORT
#endif // CONFIG_STA_SUPPORT //
DBGPRINT(RT_DEBUG_OFF, ("3. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
NICInitAsicFromEEPROM(pAd); //rt2860b
#ifdef RTMP_INTERNAL_TX_ALC
//
// Initialize the desired TSSI table
//
InitDesiredTSSITable(pAd);
#endif // RTMP_INTERNAL_TX_ALC //
// Set PHY to appropriate mode
TmpPhy = pAd->CommonCfg.PhyMode;
pAd->CommonCfg.PhyMode = 0xff;
RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
SetCommonHT(pAd);
#endif // DOT11_N_SUPPORT //
// No valid channels.
if (pAd->ChannelListNum == 0)
{
DBGPRINT(RT_DEBUG_ERROR, ("Wrong configuration. No valid channel found. Check \"ContryCode\" and \"ChannelGeography\" setting.\n"));
goto err6;
}
#ifdef DOT11_N_SUPPORT
DBGPRINT(RT_DEBUG_OFF, ("MCS Set = %02x %02x %02x %02x %02x\n", pAd->CommonCfg.HtCapability.MCSSet[0],
pAd->CommonCfg.HtCapability.MCSSet[1], pAd->CommonCfg.HtCapability.MCSSet[2],
pAd->CommonCfg.HtCapability.MCSSet[3], pAd->CommonCfg.HtCapability.MCSSet[4]));
#endif // DOT11_N_SUPPORT //
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef AP_QLOAD_SUPPORT
/* init QBSS Element */
QBSS_LoadInit(pAd);
#endif // AP_QLOAD_SUPPORT //
}
#endif // CONFIG_AP_SUPPORT //
// APInitialize(pAd);
#ifdef IKANOS_VX_1X0
VR_IKANOS_FP_Init(pAd->ApCfg.BssidNum, pAd->PermanentAddress);
#endif // IKANOS_VX_1X0 //
//
// Initialize RF register to default value
//
AsicSwitchChannel(pAd, pAd->CommonCfg.Channel, FALSE);
AsicLockChannel(pAd, pAd->CommonCfg.Channel);
/*
Some modules init must be called before APStartUp().
Or APStartUp() will make up beacon content and call
other modules API to get some information to fill.
*/
#ifdef WMM_ACM_SUPPORT
#ifdef CONFIG_AP_SUPPORT
ACMP_Init(pAd,
pAd->CommonCfg.APEdcaParm.bACM[0],
pAd->CommonCfg.APEdcaParm.bACM[1],
pAd->CommonCfg.APEdcaParm.bACM[2],
pAd->CommonCfg.APEdcaParm.bACM[3], 0);
#endif // CONFIG_AP_SUPPORT //
#ifdef CONFIG_STA_SUPPORT
ACMP_Init(pAd);
#endif // CONFIG_STA_SUPPORT //
#endif // WMM_ACM_SUPPORT //
if (pAd && (Status != NDIS_STATUS_SUCCESS))
{
//
// Undo everything if it failed
//
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
// NdisMDeregisterInterrupt(&pAd->Interrupt);
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
// RTMPFreeAdapter(pAd); // we will free it in disconnect()
}
else if (pAd)
{
// Microsoft HCT require driver send a disconnect event after driver initialization.
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_MEDIA_STATE_CONNECTED);
// pAd->IndicateMediaState = NdisMediaStateDisconnected;
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_MEDIA_STATE_CHANGE);
DBGPRINT(RT_DEBUG_TRACE, ("NDIS_STATUS_MEDIA_DISCONNECT Event B!\n"));
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
if (pAd->ApCfg.bAutoChannelAtBootup || (pAd->CommonCfg.Channel == 0))
{
UINT8 BBPValue = 0;
// Enable Interrupt first due to we need to scan channel to receive beacons.
RTMP_IRQ_ENABLE(pAd);
// Now Enable RxTx
RTMPEnableRxTx(pAd);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_START_UP);
// Let BBP register at 20MHz to do scan
RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R4, &BBPValue);
BBPValue &= (~0x18);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R4, BBPValue);
DBGPRINT(RT_DEBUG_ERROR, ("SYNC - BBP R4 to 20MHz.l\n"));
// Now we can receive the beacon and do the listen beacon
// use default BW to select channel
pAd->CommonCfg.Channel = AP_AUTO_CH_SEL(pAd, pAd->ApCfg.AutoChannelAlg);
pAd->ApCfg.bAutoChannelAtBootup = FALSE;
}
#ifdef DOT11_N_SUPPORT
// If phymode > PHY_11ABGN_MIXED and BW=40 check extension channel, after select channel
N_ChannelCheck(pAd);
#ifdef DOT11N_DRAFT3
/*
We only do this Overlapping BSS Scan when system up, for the
other situation of channel changing, we depends on station's
report to adjust ourself.
*/
if (pAd->CommonCfg.bForty_Mhz_Intolerant == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Disable 20/40 BSSCoex Channel Scan(BssCoex=%d, 40MHzIntolerant=%d)\n",
pAd->CommonCfg.bBssCoexEnable,
pAd->CommonCfg.bForty_Mhz_Intolerant));
}
else if(pAd->CommonCfg.bBssCoexEnable == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Enable 20/40 BSSCoex Channel Scan(BssCoex=%d)\n",
pAd->CommonCfg.bBssCoexEnable));
APOverlappingBSSScan(pAd);
}
RTMP_11N_D3_TimerInit(pAd);
// RTMPInitTimer(pAd, &pAd->CommonCfg.Bss2040CoexistTimer, GET_TIMER_FUNCTION(Bss2040CoexistTimeOut), pAd, FALSE);
#endif // DOT11N_DRAFT3 //
#endif // DOT11_N_SUPPORT //
#ifdef RELASE_EXCLUDE
/*
3090, 3090A and 3390 all support hadware tone radar function. But the soluation of those are different.
3090 is the old one.
*/
#endif // RELASE_EXCLUDE //
APStartUp(pAd);
DBGPRINT(RT_DEBUG_OFF, ("Main bssid = %02x:%02x:%02x:%02x:%02x:%02x\n",
PRINT_MAC(pAd->ApCfg.MBSSID[BSS0].Bssid)));
}
#endif // CONFIG_AP_SUPPORT //
}// end of else
#ifdef WSC_INCLUDED
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
INT apidx;
#ifdef HOSTAPD_SUPPORT
if (pAd->ApCfg.Hostapd == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("WPS is control by hostapd now.\n"));
}
else
#endif //HOSTAPD_SUPPORT//
for (apidx = 0; apidx < pAd->ApCfg.BssidNum; apidx++)
{
PWSC_CTRL pWscControl;
UCHAR zeros16[16]= {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
pWscControl = &pAd->ApCfg.MBSSID[apidx].WscControl;
DBGPRINT(RT_DEBUG_TRACE, ("Generate UUID for apidx(%d)\n", apidx));
if (NdisEqualMemory(&pWscControl->Wsc_Uuid_E[0], zeros16, UUID_LEN_HEX))
WscGenerateUUID(pAd, &pWscControl->Wsc_Uuid_E[0], &pWscControl->Wsc_Uuid_Str[0], apidx, FALSE);
WscInit(pAd, FALSE, apidx);
if (pWscControl->WscEnrolleePinCode == 0)
{
pWscControl->WscEnrolleePinCode = GenerateWpsPinCode(pAd, FALSE, apidx);
pWscControl->WscEnrolleePinCodeLen = 8;
}
}
}
#endif // CONFIG_AP_SUPPORT //
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
PWSC_CTRL pWscControl = &pAd->StaCfg.WscControl;
WscGenerateUUID(pAd, &pWscControl->Wsc_Uuid_E[0], &pWscControl->Wsc_Uuid_Str[0], 0, FALSE);
WscInit(pAd, BSS0);
if (pWscControl->WscEnrolleePinCode == 0)
{
pWscControl->WscEnrolleePinCode = GenerateWpsPinCode(pAd, BSS0);
pWscControl->WscEnrolleePinCodeLen = 8;
}
}
#endif // CONFIG_STA_SUPPORT //
/* WSC hardware push button function 0811 */
WSC_HDR_BTN_Init(pAd);
#endif // WSC_INCLUDED //
// Set up the Mac address
RtmpOSNetDevAddrSet(pAd->net_dev, &pAd->CurrentAddress[0]);
// Various AP function init
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MBSS_SUPPORT
/* the function can not be moved to RT2860_probe() even register_netdev()
is changed as register_netdevice().
Or in some PC, kernel will panic (Fedora 4) */
RT28xx_MBSS_Init(pAd, pAd->net_dev);
#endif // MBSS_SUPPORT //
#ifdef WDS_SUPPORT
RT28xx_WDS_Init(pAd, pAd->net_dev);
#endif // WDS_SUPPORT //
#ifdef APCLI_SUPPORT
RT28xx_ApCli_Init(pAd, pAd->net_dev);
#endif // APCLI_SUPPORT //
}
#endif // CONFIG_AP_SUPPORT //
#ifdef RTMP_RBUS_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoTurbineDynamicTune(pAd);
#endif // VIDEO_TURBINE_SUPPORT //
#endif // RTMP_RBUS_SUPPORT //
#ifdef RTMP_RBUS_SUPPORT
#ifdef RT3XXX_ANTENNA_DIVERSITY_SUPPORT
RT3XXX_AntDiversity_Init(pAd);
#endif // RT3XXX_ANTENNA_DIVERSITY_SUPPORT //
#endif // RTMP_RBUS_SUPPORT //
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MAT_SUPPORT
MATEngineInit(pAd);
#endif // MAT_SUPPORT //
#ifdef CLIENT_WDS
CliWds_ProxyTabInit(pAd);
#endif // CLIENT_WDS //
}
#endif // CONFIG_AP_SUPPORT //
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef DOT11Z_TDLS_SUPPORT
TDLS_Table_Init(pAd);
#endif // DOT11Z_TDLS_SUPPORT //
#ifdef WPA_SUPPLICANT_SUPPORT
#ifndef NATIVE_WPA_SUPPLICANT_SUPPORT
// send wireless event to wpa_supplicant for infroming interface up.
RtmpOSWrielessEventSend(pAd, IWEVCUSTOM, RT_INTERFACE_UP, NULL, NULL, 0);
#endif // NATIVE_WPA_SUPPLICANT_SUPPORT //
#endif // WPA_SUPPLICANT_SUPPORT //
}
#endif // CONFIG_STA_SUPPORT //
#if defined(RT2883) || defined(RT3883)
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
if (IS_RT2883(pAd) || IS_RT3883(pAd))
{
#ifdef RANGE_EXT_SUPPORT
RTMP_IO_WRITE32(pAd, HT_FBK_CFG1, 0xedcba980);
#endif // RANGE_EXT_SUPPORT //
RTMP_IO_WRITE32(pAd, TX_FBK_CFG_3S_0, 0x12111008);
RTMP_IO_WRITE32(pAd, TX_FBK_CFG_3S_1, 0x16151413);
}
#ifdef STREAM_MODE_SUPPORT
if (pAd->CommonCfg.StreamMode > 0)
{
ULONG streamWord = StreamModeRegVal(pAd);
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR0_L, (ULONG)(pAd->CommonCfg.StreamModeMac[0][0]) | (ULONG)(pAd->CommonCfg.StreamModeMac[0][1] << 8) |
(ULONG)(pAd->CommonCfg.StreamModeMac[0][2] << 16) | (ULONG)(pAd->CommonCfg.StreamModeMac[0][3] << 24));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR0_H, streamWord | (ULONG)(pAd->CommonCfg.StreamModeMac[0][4]) | (ULONG)(pAd->CommonCfg.StreamModeMac[0][5] << 8));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR1_L, (ULONG)(pAd->CommonCfg.StreamModeMac[1][0]) | (ULONG)(pAd->CommonCfg.StreamModeMac[1][1] << 8) |
(ULONG)(pAd->CommonCfg.StreamModeMac[1][2] << 16) | (ULONG)(pAd->CommonCfg.StreamModeMac[1][3] << 24));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR1_H, streamWord | (ULONG)(pAd->CommonCfg.StreamModeMac[1][4]) | (ULONG)(pAd->CommonCfg.StreamModeMac[1][5] << 8));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR2_L, (ULONG)(pAd->CommonCfg.StreamModeMac[2][0]) | (ULONG)(pAd->CommonCfg.StreamModeMac[2][1] << 8) |
(ULONG)(pAd->CommonCfg.StreamModeMac[2][2] << 16) | (ULONG)(pAd->CommonCfg.StreamModeMac[2][3] << 24));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR2_H, streamWord | (ULONG)(pAd->CommonCfg.StreamModeMac[2][4]) | (ULONG)(pAd->CommonCfg.StreamModeMac[2][5] << 8));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR3_L, (ULONG)(pAd->CommonCfg.StreamModeMac[3][0]) | (ULONG)(pAd->CommonCfg.StreamModeMac[3][1] << 8) |
(ULONG)(pAd->CommonCfg.StreamModeMac[3][2] << 16) | (ULONG)(pAd->CommonCfg.StreamModeMac[3][3] << 24));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR3_H, streamWord | (ULONG)(pAd->CommonCfg.StreamModeMac[3][4]) | (ULONG)(pAd->CommonCfg.StreamModeMac[3][5] << 8));
}
#endif // STREAM_MODE_SUPPORT //
}
#endif // CONFIG_AP_SUPPORT //
if (pAd->CommonCfg.FineAGC)
{
UINT8 BBPValue = 0;
BBP_IO_READ8_BY_REG_ID(pAd, BBP_R65, &BBPValue);
BBPValue |= 0x40; // turn on fine AGC
BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R65, BBPValue);
}
else
{
UINT8 BBPValue = 0;
BBP_IO_READ8_BY_REG_ID(pAd, BBP_R65, &BBPValue);
BBPValue &= ~0x40; // turn off fine AGC
BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R65, BBPValue);
}
#endif // defined(RT2883) || defined(RT3883) //
#ifdef DOT11_N_SUPPORT
#ifdef TXBF_SUPPORT
if (pAd->CommonCfg.ITxBfTimeout)
{
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R179, 0x02);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R180, 0);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R182, pAd->CommonCfg.ITxBfTimeout & 0xFF);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R180, 1);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R182, (pAd->CommonCfg.ITxBfTimeout>>8) & 0xFF);
}
int rt28xx_init(
IN PRTMP_ADAPTER pAd,
IN PSTRING pDefaultMac,
IN PSTRING pHostName)
{
UINT index;
UCHAR TmpPhy;
NDIS_STATUS Status;
UINT32 MacCsr0 = 0;
UINT16 ChipId = 0;
// reset Adapter flags
RTMP_CLEAR_FLAGS(pAd);
// Init BssTab & ChannelInfo tabbles for auto channel select.
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
//#ifdef AUTO_CH_SELECT_ENHANCE
AutoChBssTableInit(pAd);
ChannelInfoInit(pAd);
//#endif // AUTO_CH_SELECT_ENHANCE //
}
#endif // CONFIG_AP_SUPPORT //
#ifdef DOT11_N_SUPPORT
// Allocate BA Reordering memory
if (ba_reordering_resource_init(pAd, MAX_REORDERING_MPDU_NUM) != TRUE)
goto err1;
#endif // DOT11_N_SUPPORT //
// Make sure MAC gets ready.
index = 0;
do
{
RTMP_IO_READ32(pAd, MAC_CSR0, &MacCsr0);
pAd->MACVersion = MacCsr0;
/* The purpose is to identify RT5390H */
RT28xx_EEPROM_READ16(pAd, 0x00, ChipId);
pAd->ChipId = ChipId;
if ((pAd->MACVersion != 0x00) && (pAd->MACVersion != 0xFFFFFFFF))
break;
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST))
goto err1;
RTMPusecDelay(10);
} while (index++ < 100);
DBGPRINT(RT_DEBUG_TRACE, ("MAC_CSR0 [ Ver:Rev=0x%08x]\n", pAd->MACVersion));
#ifdef RT5390
if (IS_RT5390H(pAd))
DBGPRINT(RT_DEBUG_ERROR, ("The chip belongs to 0x%04x\n", pAd->ChipId));
#endif /* RT5390 */
#ifdef SPECIFIC_BCN_BUF_SUPPORT
pAd->BcnCB.DYN_MAX_MBSSID_NUM = 1;
if (IS_RT5390(pAd) || IS_RT3593(pAd))
{
pAd->BcnCB.bHighShareMemSupport = 1;
pAd->BcnCB.DYN_HW_BEACON_BASE0 = 0x4000;
pAd->BcnCB.DYN_HW_BEACON_MAX_SIZE = 0x2000;
pAd->BcnCB.DYN_HW_BEACON_MAX_COUNT = 16;
#ifdef MBSS_SUPPORT
#ifdef APCLI_SUPPORT
pAd->BcnCB.DYN_MAX_MBSSID_NUM = 8 - MAX_MESH_NUM;
#else
pAd->BcnCB.DYN_MAX_MBSSID_NUM = 16 - MAX_MESH_NUM;
#endif // APCLI_SUPPORT //
#endif // MBSS_SUPPORT //
}
else
{
pAd->BcnCB.bHighShareMemSupport = 0;
pAd->BcnCB.DYN_HW_BEACON_BASE0 = 0x7800;
pAd->BcnCB.DYN_HW_BEACON_MAX_SIZE = 0x1000;
pAd->BcnCB.DYN_HW_BEACON_MAX_COUNT = 8;
#ifdef MBSS_SUPPORT
pAd->BcnCB.DYN_MAX_MBSSID_NUM = (pAd->BcnCB.DYN_HW_BEACON_MAX_COUNT - MAX_MESH_NUM - MAX_APCLI_NUM);
#endif // MBSS_SUPPORT //
}
#endif // SPECIFIC_BCN_BUF_SUPPORT //
#ifdef RTMP_MAC_PCI
#if defined(RT3090) || defined(RT3592) || defined(RT3390) || defined(RT3593) || defined(RT5390)
/*Iverson patch PCIE L1 issue to make sure that driver can be read,write ,BBP and RF register at pcie L.1 level */
if ((IS_RT3090(pAd) || IS_RT3572(pAd) ||
IS_RT3390(pAd) || IS_RT3593(pAd) || IS_RT5390(pAd))&&pAd->infType==RTMP_DEV_INF_PCIE)
{
RTMP_IO_READ32(pAd, AUX_CTRL, &MacCsr0);
MacCsr0 |= 0x402;
RTMP_IO_WRITE32(pAd, AUX_CTRL, MacCsr0);
DBGPRINT(RT_DEBUG_TRACE, ("AUX_CTRL = 0x%x\n", MacCsr0));
}
#endif // RT3090 //
// To fix driver disable/enable hang issue when radio off
RTMP_IO_WRITE32(pAd, PWR_PIN_CFG, 0x2);
#endif // RTMP_MAC_PCI //
// Disable DMA
RT28XXDMADisable(pAd);
// Load 8051 firmware
Status = NICLoadFirmware(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICLoadFirmware failed, Status[=0x%08x]\n", Status));
goto err1;
}
NICLoadRateSwitchingParams(pAd);
// Disable interrupts here which is as soon as possible
// This statement should never be true. We might consider to remove it later
#ifdef RTMP_MAC_PCI
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_ACTIVE))
{
RTMP_ASIC_INTERRUPT_DISABLE(pAd);
}
#endif // RTMP_MAC_PCI //
#ifdef RESOURCE_PRE_ALLOC
Status = RTMPInitTxRxRingMemory(pAd);
#else
Status = RTMPAllocTxRxRingMemory(pAd);
#endif // RESOURCE_PRE_ALLOC //
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPAllocTxRxMemory failed, Status[=0x%08x]\n", Status));
goto err2;
}
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
// initialize MLME
//
Status = RtmpMgmtTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err3;
Status = MlmeInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MlmeInit failed, Status[=0x%08x]\n", Status));
goto err4;
}
#ifdef RMTP_RBUS_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoConfigInit(pAd);
#endif // VIDEO_TURBINE_SUPPORT //
#endif // RMTP_RBUS_SUPPORT //
// Initialize pAd->StaCfg, pAd->ApCfg, pAd->CommonCfg to manufacture default
//
UserCfgInit(pAd);
Status = RtmpNetTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err5;
// COPY_MAC_ADDR(pAd->ApCfg.MBSSID[apidx].Bssid, netif->hwaddr);
// pAd->bForcePrintTX = TRUE;
CfgInitHook(pAd);
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
APInitialize(pAd);
#endif // CONFIG_AP_SUPPORT //
#ifdef BLOCK_NET_IF
initblockQueueTab(pAd);
#endif // BLOCK_NET_IF //
Status = MeasureReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MeasureReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
Status = TpcReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("TpcReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
//
// Init the hardware, we need to init asic before read registry, otherwise mac register will be reset
//
Status = NICInitializeAdapter(pAd, TRUE);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICInitializeAdapter failed, Status[=0x%08x]\n", Status));
if (Status != NDIS_STATUS_SUCCESS)
goto err6;
}
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
}
#endif // CONFIG_AP_SUPPORT //
// Read parameters from Config File
/* unknown, it will be updated in NICReadEEPROMParameters */
pAd->RfIcType = RFIC_UNKNOWN;
Status = RTMPReadParametersHook(pAd);
DBGPRINT(RT_DEBUG_OFF, ("1. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPReadParametersHook failed, Status[=0x%08x]\n",Status));
goto err6;
}
#ifdef DOT11_N_SUPPORT
//Init Ba Capability parameters.
// RT28XX_BA_INIT(pAd);
pAd->CommonCfg.DesiredHtPhy.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
pAd->CommonCfg.DesiredHtPhy.AmsduEnable = (USHORT)pAd->CommonCfg.BACapability.field.AmsduEnable;
pAd->CommonCfg.DesiredHtPhy.AmsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.DesiredHtPhy.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
// UPdata to HT IE
pAd->CommonCfg.HtCapability.HtCapInfo.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
pAd->CommonCfg.HtCapability.HtCapInfo.AMsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.HtCapability.HtCapParm.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
#endif // DOT11_N_SUPPORT //
// after reading Registry, we now know if in AP mode or STA mode
// Load 8051 firmware; crash when FW image not existent
// Status = NICLoadFirmware(pAd);
// if (Status != NDIS_STATUS_SUCCESS)
// break;
DBGPRINT(RT_DEBUG_OFF, ("2. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
// We should read EEPROM for all cases. rt2860b
NICReadEEPROMParameters(pAd, (PUCHAR)pDefaultMac);
DBGPRINT(RT_DEBUG_OFF, ("3. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
NICInitAsicFromEEPROM(pAd); //rt2860b
#ifdef RTMP_INTERNAL_TX_ALC
//
// Initialize the desired TSSI table
//
InitDesiredTSSITable(pAd);
#endif // RTMP_INTERNAL_TX_ALC //
#if defined(RT5390) || defined(RT5370)
//
// Temperature compensation, initialize the lookup table
//
DBGPRINT(RT_DEBUG_ERROR, ("IS_RT5392 = %d, bAutoTxAgcG = %d\n", IS_RT5392(pAd), pAd->bAutoTxAgcG));
if (IS_RT5392(pAd) && pAd->bAutoTxAgcG && pAd->CommonCfg.TempComp != 0)
{
InitLookupTable(pAd);
}
#endif // defined(RT5390) || defined(RT5370) //
// Set PHY to appropriate mode
TmpPhy = pAd->CommonCfg.PhyMode;
pAd->CommonCfg.PhyMode = 0xff;
RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
SetCommonHT(pAd);
#endif // DOT11_N_SUPPORT //
// No valid channels.
if (pAd->ChannelListNum == 0)
{
DBGPRINT(RT_DEBUG_ERROR, ("Wrong configuration. No valid channel found. Check \"ContryCode\" and \"ChannelGeography\" setting.\n"));
goto err6;
}
#ifdef DOT11_N_SUPPORT
DBGPRINT(RT_DEBUG_OFF, ("MCS Set = %02x %02x %02x %02x %02x\n", pAd->CommonCfg.HtCapability.MCSSet[0],
pAd->CommonCfg.HtCapability.MCSSet[1], pAd->CommonCfg.HtCapability.MCSSet[2],
pAd->CommonCfg.HtCapability.MCSSet[3], pAd->CommonCfg.HtCapability.MCSSet[4]));
#endif // DOT11_N_SUPPORT //
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef AP_QLOAD_SUPPORT
/* init QBSS Element */
QBSS_LoadInit(pAd);
#endif // AP_QLOAD_SUPPORT //
//#ifdef DOT11K_RRM_SUPPORT
// RRM_CfgInit(pAd);
//#endif // DOT11K_RRM_SUPPORT //
}
#endif // CONFIG_AP_SUPPORT //
// APInitialize(pAd);
#ifdef IKANOS_VX_1X0
VR_IKANOS_FP_Init(pAd->ApCfg.BssidNum, pAd->PermanentAddress);
#endif // IKANOS_VX_1X0 //
#ifdef CONFIG_AP_SUPPORT
//
// Initialize RF register to default value
//
if (pAd->OpMode == OPMODE_AP)
{
AsicSwitchChannel(pAd, pAd->CommonCfg.Channel, FALSE);
AsicLockChannel(pAd, pAd->CommonCfg.Channel);
}
#endif // CONFIG_AP_SUPPORT //
/*
Some modules init must be called before APStartUp().
Or APStartUp() will make up beacon content and call
other modules API to get some information to fill.
*/
#ifdef WMM_ACM_SUPPORT
#ifdef CONFIG_AP_SUPPORT
ACMP_Init(pAd,
pAd->CommonCfg.APEdcaParm.bACM[0],
pAd->CommonCfg.APEdcaParm.bACM[1],
pAd->CommonCfg.APEdcaParm.bACM[2],
pAd->CommonCfg.APEdcaParm.bACM[3], 0);
#endif // CONFIG_AP_SUPPORT //
#endif // WMM_ACM_SUPPORT //
if (pAd && (Status != NDIS_STATUS_SUCCESS))
{
//
// Undo everything if it failed
//
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
// NdisMDeregisterInterrupt(&pAd->Interrupt);
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
// RTMPFreeAdapter(pAd); // we will free it in disconnect()
}
else if (pAd)
{
// Microsoft HCT require driver send a disconnect event after driver initialization.
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_MEDIA_STATE_CONNECTED);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_MEDIA_STATE_CHANGE);
DBGPRINT(RT_DEBUG_TRACE, ("NDIS_STATUS_MEDIA_DISCONNECT Event B!\n"));
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
if (pAd->ApCfg.bAutoChannelAtBootup || (pAd->CommonCfg.Channel == 0))
{
UINT8 BBPValue = 0;
// Enable Interrupt first due to we need to scan channel to receive beacons.
RTMP_IRQ_ENABLE(pAd);
// Now Enable RxTx
RTMPEnableRxTx(pAd);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_START_UP);
// Let BBP register at 20MHz to do scan
RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R4, &BBPValue);
BBPValue &= (~0x18);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R4, BBPValue);
DBGPRINT(RT_DEBUG_ERROR, ("SYNC - BBP R4 to 20MHz.l\n"));
// Now we can receive the beacon and do the listen beacon
// use default BW to select channel
pAd->CommonCfg.Channel = AP_AUTO_CH_SEL(pAd, pAd->ApCfg.AutoChannelAlg);
pAd->ApCfg.bAutoChannelAtBootup = FALSE;
}
#ifdef DOT11_N_SUPPORT
// If phymode > PHY_11ABGN_MIXED and BW=40 check extension channel, after select channel
N_ChannelCheck(pAd);
#ifdef DOT11N_DRAFT3
/*
We only do this Overlapping BSS Scan when system up, for the
other situation of channel changing, we depends on station's
report to adjust ourself.
*/
if (pAd->CommonCfg.bForty_Mhz_Intolerant == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Disable 20/40 BSSCoex Channel Scan(BssCoex=%d, 40MHzIntolerant=%d)\n",
pAd->CommonCfg.bBssCoexEnable,
pAd->CommonCfg.bForty_Mhz_Intolerant));
}
else if(pAd->CommonCfg.bBssCoexEnable == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Enable 20/40 BSSCoex Channel Scan(BssCoex=%d)\n",
pAd->CommonCfg.bBssCoexEnable));
APOverlappingBSSScan(pAd);
}
RTMP_11N_D3_TimerInit(pAd);
// RTMPInitTimer(pAd, &pAd->CommonCfg.Bss2040CoexistTimer, GET_TIMER_FUNCTION(Bss2040CoexistTimeOut), pAd, FALSE);
#endif // DOT11N_DRAFT3 //
#endif // DOT11_N_SUPPORT //
#ifdef RT3090
#ifdef TONE_RADAR_DETECT_SUPPORT
if (IS_RT3090A(pAd) || IS_RT3390(pAd) || IS_RT5390(pAd))
pAd->CommonCfg.carrier_func=TONE_RADAR_V2;
else
pAd->CommonCfg.carrier_func=TONE_RADAR_V1;
#endif // TONE_RADAR_DETECT_SUPPORT //
#endif // RT3090 //
APStartUp(pAd);
DBGPRINT(RT_DEBUG_OFF, ("Main bssid = %02x:%02x:%02x:%02x:%02x:%02x\n",
PRINT_MAC(pAd->ApCfg.MBSSID[BSS0].Bssid)));
}
#endif // CONFIG_AP_SUPPORT //
}// end of else
#ifdef WSC_INCLUDED
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
INT apidx;
#ifdef HOSTAPD_SUPPORT
if (pAd->ApCfg.Hostapd == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("WPS is control by hostapd now.\n"));
}
else
#endif //HOSTAPD_SUPPORT//
for (apidx = 0; apidx < pAd->ApCfg.BssidNum; apidx++)
{
PWSC_CTRL pWscControl;
UCHAR zeros16[16]= {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
pWscControl = &pAd->ApCfg.MBSSID[apidx].WscControl;
DBGPRINT(RT_DEBUG_TRACE, ("Generate UUID for apidx(%d)\n", apidx));
if (NdisEqualMemory(&pWscControl->Wsc_Uuid_E[0], zeros16, UUID_LEN_HEX))
WscGenerateUUID(pAd, &pWscControl->Wsc_Uuid_E[0], &pWscControl->Wsc_Uuid_Str[0], apidx, FALSE);
WscInit(pAd, FALSE, apidx);
}
}
#endif // CONFIG_AP_SUPPORT //
/* WSC hardware push button function 0811 */
WSC_HDR_BTN_Init(pAd);
#endif // WSC_INCLUDED //
// Set up the Mac address
RtmpOSNetDevAddrSet(pAd->net_dev, &pAd->CurrentAddress[0]);
// Various AP function init
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MBSS_SUPPORT
/* the function can not be moved to RT2860_probe() even register_netdev()
is changed as register_netdevice().
Or in some PC, kernel will panic (Fedora 4) */
RT28xx_MBSS_Init(pAd, pAd->net_dev);
#endif // MBSS_SUPPORT //
#ifdef WDS_SUPPORT
RT28xx_WDS_Init(pAd, pAd->net_dev);
#endif // WDS_SUPPORT //
#ifdef APCLI_SUPPORT
RT28xx_ApCli_Init(pAd, pAd->net_dev);
#endif // APCLI_SUPPORT //
}
#endif // CONFIG_AP_SUPPORT //
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MAT_SUPPORT
MATEngineInit(pAd);
#endif // MAT_SUPPORT //
#ifdef CLIENT_WDS
CliWds_ProxyTabInit(pAd);
#endif // CLIENT_WDS //
}
#endif // CONFIG_AP_SUPPORT //
#ifdef RT33xx
if (IS_RT3390(pAd))
{
RTMP_TxEvmCalibration(pAd);
}
#endif // RT33xx //
DBGPRINT_S(Status, ("<==== rt28xx_init, Status=%x\n", Status));
return TRUE;
err6:
MeasureReqTabExit(pAd);
TpcReqTabExit(pAd);
err5:
RtmpNetTaskExit(pAd);
UserCfgExit(pAd);
err4:
MlmeHalt(pAd);
err3:
RtmpMgmtTaskExit(pAd);
err2:
#ifdef RESOURCE_PRE_ALLOC
RTMPResetTxRxRingMemory(pAd);
#else
RTMPFreeTxRxRingMemory(pAd);
#endif // RESOURCE_PRE_ALLOC //
err1:
#ifdef DOT11_N_SUPPORT
if(pAd->mpdu_blk_pool.mem)
os_free_mem(pAd, pAd->mpdu_blk_pool.mem); // free BA pool
#endif // DOT11_N_SUPPORT //
// shall not set priv to NULL here because the priv didn't been free yet.
//net_dev->priv = 0;
#ifdef INF_AMAZON_SE
err0:
#endif // INF_AMAZON_SE //
#ifdef ST
err0:
#endif // ST //
DBGPRINT(RT_DEBUG_ERROR, ("!!! rt28xx Initialized fail !!!\n"));
return FALSE;
}