コード例 #1
0
ファイル: sam_nandflash.c プロジェクト: a1ien/nuttx
int board_nandflash_config(int cs)
{
  uint32_t regval;

  /* The Embest and Ronetix CM boards and one Hynix NAND HY27UF(08/16)2G2B
   * Series NAND (MT29F2G08ABAEAWP).  This part has a capacity of 256Mx8bit
   * () with spare 8Mx8 bit capacity. The device contains 2048 blocks, composed
   * by 64 x 2112 byte pages.  The effective size is approximately 256MiB.
   *
   * NAND is available on CS3.
   */

  if (cs == HSMC_CS3)
    {
      /* Make sure that the SMC peripheral is enabled. */

      sam_hsmc_enableclk();

      /* Configure the SMC */

      regval = HSMC_SETUP_NWE_SETUP(1) |  HSMC_SETUP_NCS_WRSETUP(1) |
               HSMC_SETUP_NRD_SETUP(2) | HSMC_SETUP_NCS_RDSETUP(1);
      putreg32(regval, SAM_HSMC_SETUP(HSMC_CS3));

      regval = HSMC_PULSE_NWE_PULSE(5) | HSMC_PULSE_NCS_WRPULSE(7) |
               HSMC_PULSE_NRD_PULSE(5) | HSMC_PULSE_NCS_RDPULSE(7);
      putreg32(regval, SAM_HSMC_PULSE(HSMC_CS3));

      regval = HSMC_CYCLE_NWE_CYCLE(8) | HSMC_CYCLE_NRD_CYCLE(9);
      putreg32(regval, SAM_HSMC_CYCLE(HSMC_CS3));

      regval = HSMC_TIMINGS_TCLR(3) | HSMC_TIMINGS_TADL(10) |
               HSMC_TIMINGS_TAR(3) | HSMC_TIMINGS_TRR(4) |
               HSMC_TIMINGS_TWB(5) | HSMC_TIMINGS_RBNSEL(3) |
               HSMC_TIMINGS_NFSEL;
      putreg32(regval, SAM_HSMC_TIMINGS(HSMC_CS3));

      regval = HSMC_MODE_READMODE | HSMC_MODE_WRITEMODE |
               HSMC_MODE_BIT_8 | HSMC_MODE_TDFCYCLES(1);
      putreg32(regval, SAM_HSMC_MODE(HSMC_CS3));

      /* Configure NAND PIO pins
       *
       * NAND Interface:
       *
       *   NCS3/NANDCE - Dedicated pin; no configuration needed
       *   NANDCLE     - PE21
       *   NANDALE     - PE22
       *   NRD/NANDOE  - Dedicated pin; no configuration needed
       *   NWE/NANDWE  - Dedicated pin; no configuration needed
       *   NANDRDY     - Dedicated pin; no configuration needed
       *   M_EBI_D0-7  - Dedicated pins; no configuration needed
       */

      sam_configpio(PIO_HSMC_NANDALE);
      sam_configpio(PIO_HSMC_NANDCLE);

      return OK;
    }

  return -ENODEV;
}
コード例 #2
0
ファイル: nor_main.c プロジェクト: FreddieChopin/NuttX
int nor_main(int argc, char *argv)
{
  uint32_t regval;

  /* Here we have a in memory value we can change in the debugger
   * to begin booting in NOR Flash
   */

  static volatile uint32_t wait = NOR_BOOT_MODE;

  printf("Configuring NOR FLASH on CS0 and %s\n", wait ? "waiting" : "booting");

  /* Make sure that the SMC peripheral is enabled (But of course it is... we
   * are executing from NOR FLASH now).
   */

  sam_hsmc_enableclk();

  /* The SAMA5D3x-EK has 118MB of 16-bit NOR FLASH at CS0.  The NOR FLASH
   * has already been configured by the first level ROM bootloader... we
   * simply need to modify the timing here.
   */

  regval = HSMC_SETUP_NWE_SETUP(1) |  HSMC_SETUP_NCS_WRSETUP(0) |
           HSMC_SETUP_NRD_SETUP(2) | HSMC_SETUP_NCS_RDSETUP(0);
  putreg32(regval, SAM_HSMC_SETUP(HSMC_CS0));

  regval = HSMC_PULSE_NWE_PULSE(10) | HSMC_PULSE_NCS_WRPULSE(10) |
           HSMC_PULSE_NRD_PULSE(11) | HSMC_PULSE_NCS_RDPULSE(11);
  putreg32(regval, SAM_HSMC_PULSE(HSMC_CS0));

  regval = HSMC_CYCLE_NWE_CYCLE(11) | HSMC_CYCLE_NRD_CYCLE(14);
  putreg32(regval, SAM_HSMC_CYCLE(HSMC_CS0));

  regval = HSMC_TIMINGS_TCLR(0) | HSMC_TIMINGS_TADL(0) |
           HSMC_TIMINGS_TAR(0) | HSMC_TIMINGS_TRR(0) |
           HSMC_TIMINGS_TWB(0) | HSMC_TIMINGS_RBNSEL(0);
  putreg32(regval, SAM_HSMC_TIMINGS(HSMC_CS0));

  regval = HSMC_MODE_READMODE | HSMC_MODE_WRITEMODE |
           HSMC_MODE_EXNWMODE_DISABLED | HSMC_MODE_BIT_16 |
           HSMC_MODE_TDFCYCLES(1);
  putreg32(regval, SAM_HSMC_MODE(HSMC_CS0));

  /* Interrupts must be disabled through the following.  In this configuration,
   * there should only be timer interrupts.  Your NuttX configuration must use
   * CONFIG_SERIAL_LOWCONSOLE=y or printf() will hang when the interrupts
   * are disabled!
   */

  (void)irqsave();

  /* Disable MATRIX write protection */

#if 0 /* Disabled on reset */
  putreg32(MATRIX_WPMR_WPKEY, SAM_MATRIX_WPMR);
#endif

  /* Set remap state 1.
   *
   *   Boot state:    ROM is seen at address 0x00000000
   *   Remap State 0: SRAM is seen at address 0x00000000 (through AHB slave
   *                  interface) instead of ROM.
   *   Remap State 1: HEBI is seen at address 0x00000000 (through AHB slave
   *                  interface) instead of ROM for external boot.
   *
   * REVISIT:  This does not work.  No matter what I do, the internal
   * SRAM is always visible at address zero.  I am missing something.
   */

  putreg32(MATRIX_MRCR_RCB0, SAM_MATRIX_MRCR);   /* Enable remap */
  putreg32(AXIMX_REMAP_REMAP1, SAM_AXIMX_REMAP); /* Remap HEBI */

  /* Restore MATRIX write protection */

#if 0 /* Disabled on reset */
  putreg32(MATRIX_WPMR_WPKEY | MATRIX_WPMR_WPEN, SAM_MATRIX_WPMR);
#endif

  /* Disable the caches and the MMU.  Disabling the MMU should be safe here
   * because there is a 1-to-1 identity mapping between the physical and
   * virtual addressing.
   */

  /* NOTE:  This generates crashes and lots of error, but does leave the
   * system in the proper state to run from NOR:  very ugly but usable.
   * Better than the alternative.
   */

  cp15_disable_mmu();
  cp15_disable_caches();

  /* Invalidate caches and TLBs */

  arch_invalidate_icache();
  arch_invalidate_dcache_all();
  cp15_invalidate_tlbs();

  /* Then jump into NOR flash */

  while (wait)
    {
    }

  NOR_ENTRY();

  return 0; /* We should not get here in either case */
}