/**
* @brief Write a buffer (many blocks) in the SD card.
* @note The amount of data to write should be a multiple of SD card BLOCK
* size (512 Byte).
* @param pBuffer : pointer to the buffer containing the data to be written on the SD.
* @param WriteAddr : address to write on.
* @param NumByteToWrite : number of data to write.
* @retval SD Response:
* - SD_RESPONSE_FAILURE: Sequence failed.
* - SD_RESPONSE_NO_ERROR: Sequence succeed.
*/
uint8_t SD_WriteBuffer(uint8_t *pBuffer, uint32_t WriteAddr, uint32_t NumByteToWrite)
{
uint32_t i = 0, NbrOfBlock = 0, Offset = 0;
uint8_t rvalue = SD_RESPONSE_FAILURE;
/* Calculate number of blocks to write */
NbrOfBlock = NumByteToWrite / SD_BLOCK_SIZE;
/* SD chip select low */
SD_CS_LOW();
/* Data transfer */
while (NbrOfBlock--)
{
/* Send CMD24 (SD_WRITE_BLOCK) to write blocks */
SD_SendCmd(SD_CMD_WRITE_SINGLE_BLOCK, WriteAddr + Offset, 0xFF);
/* Check if the SD acknowledged the write block command: R1 response (0x00: no errors) */
if (SD_GetResponse(SD_RESPONSE_NO_ERROR))
{
return SD_RESPONSE_FAILURE;
}
/* Send dummy byte */
SD_WriteByte(SD_DUMMY_BYTE);
/* Send the data token to signify the start of the data */
SD_WriteByte(SD_START_DATA_SINGLE_BLOCK_WRITE);
/* Write the block data to SD : write count data by block */
for (i = 0; i < SD_BLOCK_SIZE; i++)
{
/* Send the pointed byte */
SD_WriteByte(*pBuffer);
/* Point to the next location where the byte read will be saved */
pBuffer++;
}
/* Set next write address */
Offset += 512;
/* Put CRC bytes (not really needed by us, but required by SD) */
SD_ReadByte();
SD_ReadByte();
/* Read data response */
if (SD_GetDataResponse() == SD_DATA_OK)
{
/* Set response value to success */
rvalue = SD_RESPONSE_NO_ERROR;
}
else
{
/* Set response value to failure */
rvalue = SD_RESPONSE_FAILURE;
}
}
/* SD chip select high */
SD_CS_HIGH();
/* Send dummy byte: 8 Clock pulses of delay */
SD_WriteByte(SD_DUMMY_BYTE);
/* Returns the response */
return rvalue;
}
/**
* @brief Writes a block on the SD
* @param pBuffer: pointer to the buffer containing the data to be written on
* the SD.
* @param WriteAddr: address to write on.
* @param BlockSize: the SD card Data block size.
* @retval The SD Response:
* - SD_RESPONSE_FAILURE: Sequence failed
* - SD_RESPONSE_NO_ERROR: Sequence succeed
*/
uint8_t SD_WriteBlock(uint8_t* pBuffer, uint32_t WriteAddr, uint16_t BlockSize)
{
uint32_t i = 0;
uint8_t rvalue = SD_RESPONSE_FAILURE;
/*!< SD chip select low */
SD_CS_LOW();
/*!< Send CMD24 (SD_CMD_WRITE_SINGLE_BLOCK) to write multiple block */
SD_SendCmd(SD_CMD_WRITE_SINGLE_BLOCK, WriteAddr, 0xFF);
/*!< Check if the SD acknowledged the write block command: R1 response (0x00: no errors) */
if (!SD_GetResponse(SD_RESPONSE_NO_ERROR))
{
/*!< Send a dummy byte */
SD_WriteByte(SD_DUMMY_BYTE);
/*!< Send the data token to signify the start of the data */
SD_WriteByte(0xFE);
/*!< Write the block data to SD : write count data by block */
for (i = 0; i < BlockSize; i++)
{
/*!< Send the pointed byte */
SD_WriteByte(*pBuffer);
/*!< Point to the next location where the byte read will be saved */
pBuffer++;
}
/* Send DUMMY bytes when the number of data to be written are lower
than the SD card BLOCK size (512 Byte) */
for (; i != SD_BLOCK_SIZE; i++)
{
/* Send the pointed byte */
SD_WriteByte(SD_DUMMY_BYTE);
}
/*!< Put CRC bytes (not really needed by us, but required by SD) */
SD_ReadByte();
SD_ReadByte();
/*!< Read data response */
if (SD_GetDataResponse() == SD_DATA_OK)
{
rvalue = SD_RESPONSE_NO_ERROR;
}
}
/*!< SD chip select high */
SD_CS_HIGH();
/*!< Send dummy byte: 8 Clock pulses of delay */
SD_WriteByte(SD_DUMMY_BYTE);
/*!< Returns the response */
return rvalue;
}
// Send a command to the SD Card
// uiCmdIndex : Command index. 0 to 63
// uiArgument : Command argument
void SD_SendCommand(UINT8 uiCmdIndex, UINT32 uiArgument)
{
// Send command
UINT8 uiCmdByte = 64 + (uiCmdIndex & 63);
SD_WriteByte(uiCmdByte);
// Send argument
int i;
for (i = 0; i < 4; i++)
{
SD_WriteByte((uiArgument >> 24) & 0xff);
uiArgument = uiArgument << 8;
}
SD_WriteByte(0x95); // Hard coded CRC
}
/**
* @brief Reads multiple block of data from the SD.
* @param pBuffer: pointer to the buffer that receives the data read from the
* SD.
* @param ReadAddr: SD's internal address to read from.
* @param BlockSize: the SD card Data block size.
* @param NumberOfBlocks: number of blocks to be read.
* @retval The SD Response:
* - SD_RESPONSE_FAILURE: Sequence failed
* - SD_RESPONSE_NO_ERROR: Sequence succeed
*/
SD_Error SD_ReadMultiBlocks(uint8_t* pBuffer, uint32_t ReadAddr, uint16_t BlockSize, uint32_t NumberOfBlocks)
{
uint32_t i = 0, Offset = 0;
SD_Error rvalue = SD_RESPONSE_FAILURE;
/*!< SD chip select low */
SD_CS_LOW();
/*!< Data transfer */
while (NumberOfBlocks--)
{
if(flag_SDHC == 1)
{
/*!< Send CMD17 (SD_CMD_READ_SINGLE_BLOCK) to read one block */
SD_SendCmd (SD_CMD_READ_SINGLE_BLOCK,(ReadAddr + Offset)/512, 0xFF);
}
else
{
/*!< Send CMD17 (SD_CMD_READ_SINGLE_BLOCK) to read one block */
SD_SendCmd (SD_CMD_READ_SINGLE_BLOCK, ReadAddr + Offset, 0xFF);
}
/*!< Check if the SD acknowledged the read block command: R1 response (0x00: no errors) */
if (SD_GetResponse(SD_RESPONSE_NO_ERROR))
{
return SD_RESPONSE_FAILURE;
}
/*!< Now look for the data token to signify the start of the data */
if (!SD_GetResponse(SD_START_DATA_SINGLE_BLOCK_READ))
{
/*!< Read the SD block data : read NumByteToRead data */
for (i = 0; i < BlockSize; i++)
{
/*!< Read the pointed data */
*pBuffer = SD_ReadByte();
/*!< Point to the next location where the byte read will be saved */
pBuffer++;
}
/*!< Set next read address*/
Offset += 512;
/*!< get CRC bytes (not really needed by us, but required by SD) */
SD_ReadByte();
SD_ReadByte();
/*!< Set response value to success */
rvalue = SD_RESPONSE_NO_ERROR;
}
else
{
/*!< Set response value to failure */
rvalue = SD_RESPONSE_FAILURE;
}
}
/*!< SD chip select high */
SD_CS_HIGH();
/*!< Send dummy byte: 8 Clock pulses of delay */
SD_WriteByte(SD_DUMMY_BYTE);
/*!< Returns the reponse */
return rvalue;
}
/**
* @brief Put SD in Idle state.
* @param None
* @retval The SD Response:
* - SD_RESPONSE_FAILURE: Sequence failed
* - SD_RESPONSE_NO_ERROR: Sequence succeed
*/
SD_Error SD_GoIdleState(void)
{
/*!< SD chip select low */
SD_CS_LOW();
/*!< Send CMD0 (SD_CMD_GO_IDLE_STATE) to put SD in SPI mode */
SD_SendCmd(SD_CMD_GO_IDLE_STATE, 0, 0x95);
/*!< Wait for In Idle State Response (R1 Format) equal to 0x01 */
if (SD_GetResponse(SD_IN_IDLE_STATE))
{
/*!< No Idle State Response: return response failue */
return SD_RESPONSE_FAILURE;
}
/*----------Activates the card initialization process-----------*/
do
{
/*!< SD chip select high */
SD_CS_HIGH();
/*!< Send Dummy byte 0xFF */
SD_WriteByte(SD_DUMMY_BYTE);
/*!< SD chip select low */
SD_CS_LOW();
/*!< Send CMD1 (Activates the card process) until response equal to 0x0 */
SD_SendCmd(SD_CMD_SEND_OP_COND, 0, 0xFF);
/*!< Wait for no error Response (R1 Format) equal to 0x00 */
}
while (SD_GetResponse(SD_RESPONSE_NO_ERROR));
/*!< SD chip select high */
SD_CS_HIGH();
/*!< Send dummy byte 0xFF */
SD_WriteByte(SD_DUMMY_BYTE);
return SD_RESPONSE_NO_ERROR;
}
/**
* @brief Reads a block of data from the SD.
* @param pBuffer: pointer to the buffer that receives the data read from the
* SD.
* @param ReadAddr: SD's internal address to read from.
* @param BlockSize: the SD card Data block size.
* @retval The SD Response:
* - SD_RESPONSE_FAILURE: Sequence failed
* - SD_RESPONSE_NO_ERROR: Sequence succeed
*/
uint8_t SD_ReadBlock(uint8_t* pBuffer, uint32_t ReadAddr, uint16_t BlockSize)
{
uint32_t i = 0;
uint8_t rvalue = SD_RESPONSE_FAILURE;
/*!< SD chip select low */
SD_CS_LOW();
/*!< Send CMD17 (SD_CMD_READ_SINGLE_BLOCK) to read one block */
SD_SendCmd(SD_CMD_READ_SINGLE_BLOCK, ReadAddr, 0xFF);
/*!< Check if the SD acknowledged the read block command: R1 response (0x00: no errors) */
if (!SD_GetResponse(SD_RESPONSE_NO_ERROR))
{
/*!< Now look for the data token to signify the start of the data */
if (!SD_GetResponse(SD_START_DATA_SINGLE_BLOCK_READ))
{
/*!< Read the SD block data : read NumByteToRead data */
for (i = 0; i < BlockSize; i++)
{
/*!< Save the received data */
*pBuffer = SD_ReadByte();
/*!< Point to the next location where the byte read will be saved */
pBuffer++;
}
/*!< Get CRC bytes (not really needed by us, but required by SD) */
SD_ReadByte();
SD_ReadByte();
/*!< Set response value to success */
rvalue = SD_RESPONSE_NO_ERROR;
}
}
/*!< SD chip select high */
SD_CS_HIGH();
/*!< Send dummy byte: 8 Clock pulses of delay */
SD_WriteByte(SD_DUMMY_BYTE);
/*!< Returns the response */
return rvalue;
}
/**
* @brief Returns the SD status.
* @param None
* @retval The SD status.
*/
uint16_t SD_GetStatus(void)
{
uint16_t Status = 0;
/*!< SD chip select low */
SD_CS_LOW();
/*!< Send CMD13 (SD_SEND_STATUS) to get SD status */
SD_SendCmd(SD_CMD_SEND_STATUS, 0, 0xFF);
Status = SD_ReadByte();
Status |= (uint16_t)(SD_ReadByte() << 8);
/*!< SD chip select high */
SD_CS_HIGH();
/*!< Send dummy byte 0xFF */
SD_WriteByte(SD_DUMMY_BYTE);
return Status;
}
/**
* @brief Initializes the SD/SD communication.
* @param None
* @retval The SD Response:
* - SD_RESPONSE_FAILURE: Sequence failed
* - SD_RESPONSE_NO_ERROR: Sequence succeed
*/
SD_Error SD_Init(void)
{
uint32_t i = 0;
/*!< Initialize SD_SPI */
SD_LowLevel_Init();
/*!< SD chip select high */
SD_CS_HIGH();
/*!< Send dummy byte 0xFF, 10 times with CS high */
/*!< Rise CS and MOSI for 80 clocks cycles */
for (i = 0; i <= 9; i++)
{
/*!< Send dummy byte 0xFF */
SD_WriteByte(SD_DUMMY_BYTE);
}
/*------------Put SD in SPI mode--------------*/
/*!< SD initialized and set to SPI mode properly */
return (SD_GoIdleState());
}
/**
* @brief Initializes the SD/SD communication.
* @param None
* @retval The SD Response:
* - SD_RESPONSE_FAILURE: Sequence failed
* - SD_RESPONSE_NO_ERROR: Sequence succeed
*/
SD_Error SD_Init(void)
{
uint32_t TimeOut, i = 0;
SD_Error Status = SD_RESPONSE_NO_ERROR;
/*!< Initialize SD_SPI 初始化SPI相应管脚与处理器的SPI接口 */
//printf("(SD Init in SPI mode)");
SD_LowLevel_Init();
SD_SPI_SetSpeedLow();
//rt_kprintf("sd_init 0\n");
/*------------Put SD in SPI mode--------------*/
/*!< SD initialized and set to SPI mode properly */
TimeOut = 0;
do
{
/*!< SD chip select high */
SD_CS_HIGH();
/*!< Send dummy byte 0xFF, 10 times with CS high */
/*!< Rise CS and MOSI for 80 clocks cycles */
for (i = 0; i <= 9; i++)
{
/*!< Send dummy byte 0xFF */
SD_WriteByte(SD_DUMMY_BYTE);
}
Status = SD_GoIdleState();
//rt_kprintf("sd_init 1 %d\n",(uint32_t)Status);
if(TimeOut > 6)
{
break;
}
TimeOut++;
}while(Status);
SD_SPI_SetSpeedHi();
return (Status);
}
/**
* @brief Send 5 bytes command to the SD card.
* @param Cmd: The user expected command to send to SD card.
* @param Arg: The command argument.
* @param Crc: The CRC.
* @retval None
*/
void SD_SendCmd(uint8_t Cmd, uint32_t Arg, uint8_t Crc)
{
uint32_t i = 0x00;
uint8_t Frame[6];
Frame[0] = (Cmd | 0x40); /*!< Construct byte 1 */
Frame[1] = (uint8_t)(Arg >> 24); /*!< Construct byte 2 */
Frame[2] = (uint8_t)(Arg >> 16); /*!< Construct byte 3 */
Frame[3] = (uint8_t)(Arg >> 8); /*!< Construct byte 4 */
Frame[4] = (uint8_t)(Arg); /*!< Construct byte 5 */
Frame[5] = (Crc); /*!< Construct CRC: byte 6 */
for (i = 0; i < 6; i++)
{
SD_WriteByte(Frame[i]); /*!< Send the Cmd bytes */
}
}
/**
* @brief Read the CID card register.
* Reading the contents of the CID register in SPI mode is a simple
* read-block transaction.
* @param SD_cid: pointer on an CID register structure
* @retval The SD Response:
* - SD_RESPONSE_FAILURE: Sequence failed
* - SD_RESPONSE_NO_ERROR: Sequence succeed
*/
SD_Error SD_GetCIDRegister(SD_CID* SD_cid)
{
uint32_t i = 0;
SD_Error rvalue = SD_RESPONSE_FAILURE;
uint8_t CID_Tab[16];
/*!< SD chip select low */
SD_CS_LOW();
/*!< Send CMD10 (CID register) */
SD_SendCmd(SD_CMD_SEND_CID, 0, 0xFF);
/*!< Wait for response in the R1 format (0x00 is no errors) */
if (!SD_GetResponse(SD_RESPONSE_NO_ERROR))
{
if (!SD_GetResponse(SD_START_DATA_SINGLE_BLOCK_READ))
{
/*!< Store CID register value on CID_Tab */
for (i = 0; i < 16; i++)
{
CID_Tab[i] = SD_ReadByte();
}
}
/*!< Get CRC bytes (not really needed by us, but required by SD) */
SD_WriteByte(SD_DUMMY_BYTE);
SD_WriteByte(SD_DUMMY_BYTE);
/*!< Set response value to success */
rvalue = SD_RESPONSE_NO_ERROR;
}
/*!< SD chip select high */
SD_CS_HIGH();
/*!< Send dummy byte: 8 Clock pulses of delay */
SD_WriteByte(SD_DUMMY_BYTE);
/*!< Byte 0 */
SD_cid->ManufacturerID = CID_Tab[0];
/*!< Byte 1 */
SD_cid->OEM_AppliID = CID_Tab[1] << 8;
/*!< Byte 2 */
SD_cid->OEM_AppliID |= CID_Tab[2];
/*!< Byte 3 */
SD_cid->ProdName1 = CID_Tab[3] << 24;
/*!< Byte 4 */
SD_cid->ProdName1 |= CID_Tab[4] << 16;
/*!< Byte 5 */
SD_cid->ProdName1 |= CID_Tab[5] << 8;
/*!< Byte 6 */
SD_cid->ProdName1 |= CID_Tab[6];
/*!< Byte 7 */
SD_cid->ProdName2 = CID_Tab[7];
/*!< Byte 8 */
SD_cid->ProdRev = CID_Tab[8];
/*!< Byte 9 */
SD_cid->ProdSN = CID_Tab[9] << 24;
/*!< Byte 10 */
SD_cid->ProdSN |= CID_Tab[10] << 16;
/*!< Byte 11 */
SD_cid->ProdSN |= CID_Tab[11] << 8;
/*!< Byte 12 */
SD_cid->ProdSN |= CID_Tab[12];
/*!< Byte 13 */
SD_cid->Reserved1 |= (CID_Tab[13] & 0xF0) >> 4;
SD_cid->ManufactDate = (CID_Tab[13] & 0x0F) << 8;
/*!< Byte 14 */
SD_cid->ManufactDate |= CID_Tab[14];
/*!< Byte 15 */
SD_cid->CID_CRC = (CID_Tab[15] & 0xFE) >> 1;
SD_cid->Reserved2 = 1;
/*!< Return the reponse */
return rvalue;
}
/**
* @brief Read the CSD card register.
* Reading the contents of the CSD register in SPI mode is a simple
* read-block transaction.
* @param SD_csd: pointer on an SCD register structure
* @retval The SD Response:
* - SD_RESPONSE_FAILURE: Sequence failed
* - SD_RESPONSE_NO_ERROR: Sequence succeed
*/
SD_Error SD_GetCSDRegister(SD_CSD* SD_csd)
{
uint32_t i = 0;
SD_Error rvalue = SD_RESPONSE_FAILURE;
uint8_t CSD_Tab[16];
/*!< SD chip select low */
SD_CS_LOW();
/*!< Send CMD9 (CSD register) or CMD10(CSD register) */
SD_SendCmd(SD_CMD_SEND_CSD, 0, 0xFF);
/*!< Wait for response in the R1 format (0x00 is no errors) */
if (!SD_GetResponse(SD_RESPONSE_NO_ERROR))
{
if (!SD_GetResponse(SD_START_DATA_SINGLE_BLOCK_READ))
{
for (i = 0; i < 16; i++)
{
/*!< Store CSD register value on CSD_Tab */
CSD_Tab[i] = SD_ReadByte();
}
}
/*!< Get CRC bytes (not really needed by us, but required by SD) */
SD_WriteByte(SD_DUMMY_BYTE);
SD_WriteByte(SD_DUMMY_BYTE);
/*!< Set response value to success */
rvalue = SD_RESPONSE_NO_ERROR;
}
/*!< SD chip select high */
SD_CS_HIGH();
/*!< Send dummy byte: 8 Clock pulses of delay */
SD_WriteByte(SD_DUMMY_BYTE);
/*!< Byte 0 */
SD_csd->CSDStruct = (CSD_Tab[0] & 0xC0) >> 6;
SD_csd->SysSpecVersion = (CSD_Tab[0] & 0x3C) >> 2;
SD_csd->Reserved1 = CSD_Tab[0] & 0x03;
/*!< Byte 1 */
SD_csd->TAAC = CSD_Tab[1];
/*!< Byte 2 */
SD_csd->NSAC = CSD_Tab[2];
/*!< Byte 3 */
SD_csd->MaxBusClkFrec = CSD_Tab[3];
/*!< Byte 4 */
SD_csd->CardComdClasses = CSD_Tab[4] << 4;
/*!< Byte 5 */
SD_csd->CardComdClasses |= (CSD_Tab[5] & 0xF0) >> 4;
SD_csd->RdBlockLen = CSD_Tab[5] & 0x0F;
/*!< Byte 6 */
SD_csd->PartBlockRead = (CSD_Tab[6] & 0x80) >> 7;
SD_csd->WrBlockMisalign = (CSD_Tab[6] & 0x40) >> 6;
SD_csd->RdBlockMisalign = (CSD_Tab[6] & 0x20) >> 5;
SD_csd->DSRImpl = (CSD_Tab[6] & 0x10) >> 4;
SD_csd->Reserved2 = 0; /*!< Reserved */
SD_csd->DeviceSize = (CSD_Tab[6] & 0x03) << 10;
/*!< Byte 7 */
SD_csd->DeviceSize |= (CSD_Tab[7]) << 2;
/*!< Byte 8 */
SD_csd->DeviceSize |= (CSD_Tab[8] & 0xC0) >> 6;
SD_csd->MaxRdCurrentVDDMin = (CSD_Tab[8] & 0x38) >> 3;
SD_csd->MaxRdCurrentVDDMax = (CSD_Tab[8] & 0x07);
/*!< Byte 9 */
SD_csd->MaxWrCurrentVDDMin = (CSD_Tab[9] & 0xE0) >> 5;
SD_csd->MaxWrCurrentVDDMax = (CSD_Tab[9] & 0x1C) >> 2;
SD_csd->DeviceSizeMul = (CSD_Tab[9] & 0x03) << 1;
/*!< Byte 10 */
SD_csd->DeviceSizeMul |= (CSD_Tab[10] & 0x80) >> 7;
SD_csd->EraseGrSize = (CSD_Tab[10] & 0x40) >> 6;
SD_csd->EraseGrMul = (CSD_Tab[10] & 0x3F) << 1;
/*!< Byte 11 */
SD_csd->EraseGrMul |= (CSD_Tab[11] & 0x80) >> 7;
SD_csd->WrProtectGrSize = (CSD_Tab[11] & 0x7F);
/*!< Byte 12 */
SD_csd->WrProtectGrEnable = (CSD_Tab[12] & 0x80) >> 7;
SD_csd->ManDeflECC = (CSD_Tab[12] & 0x60) >> 5;
SD_csd->WrSpeedFact = (CSD_Tab[12] & 0x1C) >> 2;
SD_csd->MaxWrBlockLen = (CSD_Tab[12] & 0x03) << 2;
/*!< Byte 13 */
SD_csd->MaxWrBlockLen |= (CSD_Tab[13] & 0xC0) >> 6;
SD_csd->WriteBlockPaPartial = (CSD_Tab[13] & 0x20) >> 5;
SD_csd->Reserved3 = 0;
SD_csd->ContentProtectAppli = (CSD_Tab[13] & 0x01);
/*!< Byte 14 */
SD_csd->FileFormatGrouop = (CSD_Tab[14] & 0x80) >> 7;
SD_csd->CopyFlag = (CSD_Tab[14] & 0x40) >> 6;
SD_csd->PermWrProtect = (CSD_Tab[14] & 0x20) >> 5;
SD_csd->TempWrProtect = (CSD_Tab[14] & 0x10) >> 4;
SD_csd->FileFormat = (CSD_Tab[14] & 0x0C) >> 2;
SD_csd->ECC = (CSD_Tab[14] & 0x03);
/*!< Byte 15 */
SD_csd->CSD_CRC = (CSD_Tab[15] & 0xFE) >> 1;
SD_csd->Reserved4 = 1;
/*!< Return the reponse */
return rvalue;
}
/**
* @brief Read the CSD card register.
* Reading the contents of the CSD register in SPI mode is a simple
* read-block transaction.
* @param SD_csd: pointer on an SCD register structure
* @retval The SD Response:
* - SD_RESPONSE_FAILURE: Sequence failed
* - SD_RESPONSE_NO_ERROR: Sequence succeed
*/
SD_Error SD_GetCSDRegister(SD_CSD* SD_csd)
{
uint32_t i = 0;
SD_Error rvalue = SD_RESPONSE_FAILURE;
uint8_t CSD_Tab[16];
uint32_t CardCapacity;
static uint32_t times = 0;
/*!< SD chip select low */
SD_CS_LOW();
/*!< Send CMD9 (CSD register) or CMD10(CSD register) */
SD_SendCmd(SD_CMD_SEND_CSD, 0, 0xFF);
/*!< Wait for response in the R1 format (0x00 is no errors) */
if (!SD_GetResponse(SD_RESPONSE_NO_ERROR))
{
if (!SD_GetResponse(SD_START_DATA_SINGLE_BLOCK_READ))
{
for (i = 0; i < 16; i++)
{
/*!< Store CSD register value on CSD_Tab */
CSD_Tab[i] = SD_ReadByte();
//if(0 == times)
//{
// printf("\n\r CSD_Tab[%d] 0x%X", i, CSD_Tab[i]);
//}
}
}
/*!< Get CRC bytes (not really needed by us, but required by SD) */
SD_WriteByte(SD_DUMMY_BYTE);
SD_WriteByte(SD_DUMMY_BYTE);
/*!< Set response value to success */
rvalue = SD_RESPONSE_NO_ERROR;
}
else
{
return rvalue;
}
/*!< SD chip select high */
SD_CS_HIGH();
/*!< Send dummy byte: 8 Clock pulses of delay */
SD_WriteByte(SD_DUMMY_BYTE);
/*!< Byte 0 */
SD_csd->CSDStruct = (CSD_Tab[0] & 0xC0) >> 6;
SD_csd->SysSpecVersion = (CSD_Tab[0] & 0x3C) >> 2;
SD_csd->Reserved1 = CSD_Tab[0] & 0x03;
if(0 == times)
{
if(SD_csd->CSDStruct == 1)
{
//printf("\n\r SDHC CSD Version 2.0 Acess AS SD High Capacity.");
flag_SDHC = 1;
}
else
{
//printf("\n\r SDSC CSD Version 1.0 Acess AS SD Standard Capacity.");
flag_SDHC = 0;
}
}
/*!< Byte 1 */
SD_csd->TAAC = CSD_Tab[1];
/*!< Byte 2 */
SD_csd->NSAC = CSD_Tab[2];
/*!< Byte 3 */
SD_csd->MaxBusClkFrec = CSD_Tab[3];
/*!< Byte 4 */
SD_csd->CardComdClasses = CSD_Tab[4] << 4;
/*!< Byte 5 */
SD_csd->CardComdClasses |= (CSD_Tab[5] & 0xF0) >> 4;
SD_csd->RdBlockLen = CSD_Tab[5] & 0x0F;
/*!< Byte 6 */
SD_csd->PartBlockRead = (CSD_Tab[6] & 0x80) >> 7;
SD_csd->WrBlockMisalign = (CSD_Tab[6] & 0x40) >> 6;
SD_csd->RdBlockMisalign = (CSD_Tab[6] & 0x20) >> 5;
SD_csd->DSRImpl = (CSD_Tab[6] & 0x10) >> 4;
SD_csd->Reserved2 = 0; /*!< Reserved */
if(flag_SDHC == 0)
{
SD_csd->DeviceSize = (CSD_Tab[6] & 0x03) << 10;
/*!< Byte 7 */
SD_csd->DeviceSize |= (CSD_Tab[7]) << 2;
/*!< Byte 8 */
SD_csd->DeviceSize |= (CSD_Tab[8] & 0xC0) >> 6;
}
