/**
* @brief Select SPI CS pin.
*
*/
void ICACHE_FLASH_ATTR SPICsPinSelect(SpiNum spiNum, SpiPinCS pinCs)
{
if (spiNum > SpiNum_HSPI) {
return;
}
// clear select
SET_PERI_REG_BITS(SPI_PIN(spiNum), 3, 0, 0);
SET_PERI_REG_MASK(SPI_PIN(spiNum), pinCs);
}
void W25QXX_Write_Page(uint8 data,uint32 WriteAddr,uint16 NumByteToWrite)
{
u16 i=0;
spi_mast_byte_write(SPI,0x06);
SET_PERI_REG_MASK(SPI_PIN(SPI), SPI_CS_DIS);
spi_mast_byte_write(SPI,0x02);
spi_mast_byte_write(SPI,(u8)((WriteAddr)>>16));
spi_mast_byte_write(SPI,(u8)((WriteAddr)>>8));
spi_mast_byte_write(SPI,(u8)WriteAddr);
while(i<NumByteToWrite)
{
spi_mast_byte_write(HSPI,data);
i++;
}
CLEAR_PERI_REG_MASK(SPI_PIN(SPI), SPI_CS_DIS);
if (i==NumByteToWrite){
spi_mast_byte_write(HSPI,data);
}
}
/**
* @brief Based on pAttr initialize SPI module.
*
*/
void ICACHE_FLASH_ATTR SPIInit (SpiNum spiNum, SpiAttr* pAttr)
{
if ((spiNum > SpiNum_HSPI) || (NULL == pAttr))
{
return;
}
// SPI_CPOL & SPI_CPHA
switch (pAttr->subMode)
{
case SpiSubMode_1:
CLEAR_PERI_REG_MASK(SPI_PIN(spiNum), SPI_IDLE_EDGE);
SET_PERI_REG_MASK(SPI_USER(spiNum), SPI_CK_OUT_EDGE); // CHPA_FALLING_EDGE_SAMPLE
break;
case SpiSubMode_2:
SET_PERI_REG_MASK(SPI_PIN(spiNum), SPI_IDLE_EDGE);
SET_PERI_REG_MASK(SPI_USER(spiNum), SPI_CK_OUT_EDGE); // CHPA_FALLING_EDGE_SAMPLE
break;
case SpiSubMode_3:
SET_PERI_REG_MASK(SPI_PIN(spiNum), SPI_IDLE_EDGE);
CLEAR_PERI_REG_MASK(SPI_USER(spiNum), SPI_CK_OUT_EDGE);
break;
case SpiSubMode_0:
default:
CLEAR_PERI_REG_MASK(SPI_PIN(spiNum), SPI_IDLE_EDGE);
CLEAR_PERI_REG_MASK(SPI_USER(spiNum), SPI_CK_OUT_EDGE);
// To do nothing
break;
}
// SPI bit order
if (SpiBitOrder_MSBFirst == pAttr->bitOrder)
{
CLEAR_PERI_REG_MASK(SPI_CTRL(spiNum), SPI_WR_BIT_ORDER);
CLEAR_PERI_REG_MASK(SPI_CTRL(spiNum), SPI_RD_BIT_ORDER);
}
else if (SpiBitOrder_LSBFirst == pAttr->bitOrder)
{
SET_PERI_REG_MASK(SPI_CTRL(spiNum), SPI_WR_BIT_ORDER);
SET_PERI_REG_MASK(SPI_CTRL(spiNum), SPI_RD_BIT_ORDER);
}
else
{
// To do nothing
}
// Disable flash operation mode
// As earlier as better, if not SPI_CTRL2 can not to be set delay cycles.
CLEAR_PERI_REG_MASK(SPI_USER(spiNum), SPI_FLASH_MODE);
// SPI mode type
if (SpiMode_Master == pAttr->mode)
{
// SPI mode type
CLEAR_PERI_REG_MASK(SPI_SLAVE(spiNum), SPI_SLAVE_MODE);
// SPI Send buffer
CLEAR_PERI_REG_MASK(SPI_USER(spiNum), SPI_USR_MISO_HIGHPART);// By default slave send buffer C0-C7
// SPI Speed
if (1 < (pAttr->speed))
{
uint8 i, k;
i = (pAttr->speed / 40) ? (pAttr->speed / 40) : 1;
k = pAttr->speed / i;
CLEAR_PERI_REG_MASK(SPI_CLOCK(spiNum), SPI_CLK_EQU_SYSCLK);
WRITE_PERI_REG(SPI_CLOCK(spiNum),
(((i - 1) & SPI_CLKDIV_PRE) << SPI_CLKDIV_PRE_S) |
(((k - 1) & SPI_CLKCNT_N) << SPI_CLKCNT_N_S) |
((((k + 1) / 2 - 1) & SPI_CLKCNT_H) << SPI_CLKCNT_H_S) |
(((k - 1) & SPI_CLKCNT_L) << SPI_CLKCNT_L_S)); //clear bit 31,set SPI clock div
}
else
{
WRITE_PERI_REG(SPI_CLOCK(spiNum), SPI_CLK_EQU_SYSCLK); // 80Mhz speed
}
// By default format:CMD+ADDR+DATA
SET_PERI_REG_MASK(SPI_USER(spiNum),
SPI_CS_SETUP | SPI_CS_HOLD | SPI_USR_MOSI);
//delay num
SET_PERI_REG_MASK(SPI_CTRL2(spiNum),
((0x1 & SPI_MISO_DELAY_NUM) << SPI_MISO_DELAY_NUM_S));
}
else if (SpiMode_Slave == pAttr->mode)
{
// BIT19 must do
SET_PERI_REG_MASK(SPI_PIN(spiNum), BIT19);
// SPI mode type
SET_PERI_REG_MASK(SPI_SLAVE(spiNum), SPI_SLAVE_MODE);
// SPI Send buffer
SET_PERI_REG_MASK(SPI_USER(spiNum), SPI_USR_MISO_HIGHPART);// By default slave send buffer C8-C15
SET_PERI_REG_MASK(SPI_USER(spiNum), SPI_USR_MOSI);
// If do not set delay cycles, slave not working,master cann't get the data.
SET_PERI_REG_MASK(SPI_CTRL2(spiNum),
((0x1 & SPI_MOSI_DELAY_NUM) << SPI_MOSI_DELAY_NUM_S)); //delay num
// SPI Speed
WRITE_PERI_REG(SPI_CLOCK(spiNum), 0);
// By default format::CMD(8bits)+ADDR(8bits)+DATA(32bytes).
SET_PERI_REG_BITS(SPI_USER2(spiNum), SPI_USR_COMMAND_BITLEN,
7, SPI_USR_COMMAND_BITLEN_S);
SET_PERI_REG_BITS(SPI_SLAVE1(spiNum), SPI_SLV_WR_ADDR_BITLEN,
7, SPI_SLV_WR_ADDR_BITLEN_S);
SET_PERI_REG_BITS(SPI_SLAVE1(spiNum), SPI_SLV_RD_ADDR_BITLEN,
7, SPI_SLV_RD_ADDR_BITLEN_S);
SET_PERI_REG_BITS(SPI_SLAVE1(spiNum), SPI_SLV_BUF_BITLEN,
(32 * 8 - 1), SPI_SLV_BUF_BITLEN_S);
// For 8266 work on slave mode.
SET_PERI_REG_BITS(SPI_SLAVE1(spiNum), SPI_SLV_STATUS_BITLEN,
7, SPI_SLV_STATUS_BITLEN_S);
}
else
{
// To do nothing
}
//clear Daul or Quad lines transmission mode
CLEAR_PERI_REG_MASK(SPI_CTRL(spiNum),
SPI_QIO_MODE | SPI_DIO_MODE | SPI_DOUT_MODE | SPI_QOUT_MODE);
// Clear the data buffer.
uint8 i;
uint32 regAddr = REG_SPI_BASE(spiNum) + 0x40;
for (i = 0; i < 16; ++i)
{
WRITE_PERI_REG(regAddr, 0);
regAddr += 4;
}
}
