//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - Warning: pins connected to the default STDIO_UART_TX and STDIO_UART_RX pins are commented
// See https://os.mbed.com/teams/ST/wiki/STDIO for more information.
//
//==============================================================================
//*** ADC ***
MBED_WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 // Connected to B_USER
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 // Connected to ARD_A1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 // Connected to ARD_A2
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 // Connected to CODEC_MCK [WM8994ECS_MCLK1]
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4 // Connected to ARD_D8
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5 // Connected to ARD_A3
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 // Connected to SD_CMD
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 // Connected to DFSDM2_DATIN1
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 // Connected to ARD_D6
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9 // Connected to ARD_A4
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10 // Connected to ARD_A0
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11 // Connected to CTP_INT
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12 // Connected to CODEC_ext_SD [WM8994ECS_ADC_DAT1]
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13 // Connected to CODEC_SD [WM8994ECS_DACDAT1]
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14 // Connected to ARD_A5
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15 // Connected to LED2_GREEN
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#include "PeripheralPins.h"
// =====
// Note: Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// =====
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
// {PA_0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC2_IN0 // choice: PA_0 with ADC_1
// {PA_0, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC3_IN0 // choice: PA_0 with ADC_1
// {PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 // Ethernet RMII Reference Clock
// {PA_1, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC2_IN1 // Ethernet RMII Reference Clock
// {PA_1, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC3_IN1 // Ethernet RMII Reference Clock
// {PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 // Ethernet RMII MDIO
// {PA_2, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC2_IN2 // Ethernet RMII MDIO
// {PA_2, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC3_IN2 // Ethernet RMII MDIO
// {PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 // choice: PA_3 with ADC_3
// {PA_3, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN3 // choice: PA_3 with ADC_3
{PA_3, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC3_IN3
// {PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4 // choice: PA_4 with ADC_2
{PA_4, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
// {PA_5, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5 // choice: PA_5 with ADC_1
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#include "PeripheralPins.h"
// =====
// Note: Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// =====
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - Warning: pins connected to the default STDIO_UART_TX and STDIO_UART_RX pins are commented
// See https://os.mbed.com/teams/ST/wiki/STDIO for more information.
//
//==============================================================================
//*** ADC ***
MBED_WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC_IN0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC_IN1
// {PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC_IN2 // Connected to STDIO_UART_TX
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC_IN3
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC_IN5
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC_IN6
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC_IN7
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC_IN8
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC_IN9
{NC, NC, 0}
};
MBED_WEAK const PinMap PinMap_ADC_Internal[] = {
{ADC_TEMP, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 16, 0)},
{ADC_VREF, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 17, 0)},
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#include "PeripheralPins.h"
// =====
// Note: Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// =====
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
{ADC_TEMP, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 16, 0)}, // See in analogin_api.c the correct ADC channel used
{ADC_VREF, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 17, 0)}, // See in analogin_api.c the correct ADC channel used
{ADC_VBAT, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 18, 0)}, // See in analogin_api.c the correct ADC channel used
{NC, NC, 0}
};
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#include "PeripheralPins.h"
// =====
// Note: Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// =====
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 5, 0)}, // IN5 - ARDUINO A0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 6, 0)}, // IN6 - ARDUINO A1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 7, 0)}, // IN7
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 8, 0)}, // IN8
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 9, 0)}, // IN9 - ARDUINO A2
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 10, 0)}, // IN10
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 11, 0)}, // IN11
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 12, 0)}, // IN12
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 15, 0)}, // IN15 - ARDUINO A3
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 16, 0)}, // IN16
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 1, 0)}, // IN1 - ARDUINO A5
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 2, 0)}, // IN2 - ARDUINO A4
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 3, 0)}, // IN3
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 4, 0)}, // IN4
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 13, 0)}, // IN13
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 14, 0)}, // IN14
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#include "PeripheralPins.h"
// =====
// Note: Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// =====
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
{PF_6, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC3_IN4
{PF_7, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC3_IN5
{NC, NC, 0}
};
const PinMap PinMap_ADC_Internal[] = {
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - Warning: pins connected to the default STDIO_UART_TX and STDIO_UART_RX pins are commented
// See https://os.mbed.com/teams/ST/wiki/STDIO for more information.
//
//==============================================================================
//*** ADC ***
MBED_WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
{PA_0_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC2_IN0
{PA_0_ALT1, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC3_IN0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
{PA_1_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC2_IN1
{PA_1_ALT1, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC3_IN1
// {PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 // Connected to STDIO_UART_TX
// {PA_2, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC2_IN2 // Connected to STDIO_UART_TX
// {PA_2, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC3_IN2 // Connected to STDIO_UART_TX
// {PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 // Connected to STDIO_UART_RX
// {PA_3, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN3 // Connected to STDIO_UART_RX
// {PA_3, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC3_IN3 // Connected to STDIO_UART_RX
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
{PA_4_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5 // Connected to LD2 [Green Led]
{PA_5_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5 // Connected to LD2 [Green Led]
// pin (i.e. PwmOut pwm(PA_7_ALT0);). These pins are not displayed on the board
// pinout image on mbed.org.
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - All mapping tables are declared as weak to allow custom overwrites for similar MCU models.
//
//==============================================================================
//*** ADC ***
__weak const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 16, 0)}, // ADC1_IN16
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
#include "PeripheralPins.h"
// =============================================================================
// Notes:
// * Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// * Only the pins that are placed on the Arduino connector are described.
// =============================================================================
//*** ADC ***
const PinMap PinMap_ADC[] = {
// {PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4 - ARDUINO A1
{PA_4, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4 - ARDUINO A1
// {PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 - ARDUINO A0
{PA_6, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6 - ARDUINO A0
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,12, 0)}, // ADC1_IN12 - ARDUINO A2
// {PC_2, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,12, 0)}, // ADC2_IN12 - ARDUINO A2
{PF_6, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC3_IN4 - ARDUINO D3
{PF_7, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC3_IN5 - ARDUINO D6
{PF_8, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC3_IN6 - ARDUINO A4
{PF_9, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC3_IN7 - ARDUINO A5
{PF_10, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC3_IN8 - ARDUINO A3
{ADC_TEMP, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 16, 0)}, // See in analogin_api.c the correct ADC channel used
{ADC_VREF, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 17, 0)}, // See in analogin_api.c the correct ADC channel used
{ADC_VBAT, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 18, 0)}, // See in analogin_api.c the correct ADC channel used
{NC, NC, 0}
};
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#include "PeripheralPins.h"
// =====
// Note: Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// =====
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC_IN0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC_IN1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC_IN2
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC_IN3
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC_IN5
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC_IN6
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC_IN7
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC_IN8
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC_IN9
{PB_12, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 18, 0)}, // ADC_IN18
{PB_13, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 19, 0)}, // ADC_IN19
{PB_14, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 20, 0)}, // ADC_IN20
{PB_15, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 21, 0)}, // ADC_IN21
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC_IN10
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC_IN11
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#include "PeripheralPins.h"
// =====
// Note: Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// =====
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC_IN0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC_IN1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC_IN2
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC_IN3
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC_IN5
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC_IN6
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC_IN7
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC_IN8
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC_IN9
{PB_12, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 18, 0)}, // ADC_IN18
{PB_13, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 19, 0)}, // ADC_IN19
{PB_14, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 20, 0)}, // ADC_IN20
{PB_15, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 21, 0)}, // ADC_IN21
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC_IN10
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC_IN11
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - Warning: pins connected to the default STDIO_UART_TX and STDIO_UART_RX pins are commented
// See https://os.mbed.com/teams/ST/wiki/STDIO for more information.
//
//==============================================================================
//*** ADC ***
MBED_WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC_IN0 // Connected to B1 [Blue PushButton]
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC_IN1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC_IN2
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC_IN3
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC_IN5
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC_IN6
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC_IN7
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC_IN8
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC_IN9
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC_IN10
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC_IN11
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC_IN12
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC_IN13
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC_IN14
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC_IN15
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#include "PeripheralPins.h"
// =====
// Note: Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// =====
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 - ARDUINO A0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 - ARDUINO A1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5 - ARDUINO A2
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11 - ARDUINO A3
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
{PB_11, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
{PB_13, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 - ARDUINO A5
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 - ARDUINO A4
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - Warning: pins connected to the default STDIO_UART_TX and STDIO_UART_RX pins are commented
// See https://os.mbed.com/teams/ST/wiki/STDIO for more information.
//
//==============================================================================
//*** ADC ***
MBED_WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC_IN0 // Connected to B1 [Blue PushButton]
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC_IN1 // Connected to MFX_WAKEUP
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC_IN2 // Connected to TSC_G1_IO3
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC_IN3 // Connected to TSC_G1_IO4
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC_IN5 // Connected to LD_R [LD4 Red Led]
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC_IN6 // Connected to TSC_G2_IO3
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC_IN7 // Connected to TSC_G2_IO4
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC_IN8 // Connected to TSC_G3_IO2
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC_IN9 // Connected to TSC_G3_IO3
{NC, NC, 0}
};
MBED_WEAK const PinMap PinMap_ADC_Internal[] = {
{ADC_TEMP, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 18, 0)},
{ADC_VREF, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 17, 0)},
*/
#include "PeripheralPins.h"
// =============================================================================
// Notes:
// * Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// * Only the pins that are placed on the Arduino connector are described.
// =============================================================================
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 - ARDUINO A0
// {PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 (used by ethernet)
// {PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 (used by ethernet)
{PA_3, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN2
{PA_4, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4
{PA_5, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5 - ARDUINO D13
{PA_6, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6 - ARDUINO D12
{PA_7, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7 (JP6) - ARDUINO D11
// {PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 (used by LED1)
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,10, 0)}, // ADC1_IN10 - ARDUINO A1
// {PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,11, 0)}, // ADC1_IN11 (used by ethernet)
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,12, 0)}, // ADC1_IN12
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,13, 0)}, // ADC1_IN13 - ARDUINO A2
// {PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,14, 0)}, // ADC1_IN14 (used by ethernet)
// {PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,15, 0)}, // ADC1_IN15 (used by ethernet)
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - Warning: pins connected to the default STDIO_UART_TX and STDIO_UART_RX pins are commented
// See https://os.mbed.com/teams/ST/wiki/STDIO for more information.
//
//==============================================================================
//*** ADC ***
MBED_WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
// {PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 // Connected to STDIO_UART_TX
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
{PA_4, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC2_IN1
{PA_5, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC2_IN2
{PA_6, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN3
{PA_7, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
{NC, NC, 0}
};
MBED_WEAK const PinMap PinMap_ADC_Internal[] = {
{ADC_TEMP, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 16, 0)}, // ADC1_IN16
{ADC_VREF1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 18, 0)}, // ADC1_IN18
// - The pins mentionned Px_y_ALTz are alternative possibilities which use other
// HW peripheral instances. You can use them the same way as any other "normal"
// pin (i.e. PwmOut pwm(PA_7_ALT0);). These pins are not displayed on the board
// pinout image on mbed.org.
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
//==============================================================================
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 5, 0)}, // ARDUINO D1
{PA_0_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 5, 0)}, // ARDUINO D1
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 6, 0)}, // ARDUINO D0
{PA_1_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 6, 0)}, // ARDUINO D0
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 7, 0)}, // ARDUINO D10
{PA_2_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 7, 0)}, // ARDUINO D10
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 8, 0)}, // ARDUINO D4
{PA_3_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 8, 0)}, // ARDUINO D4
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 9, 0)}, // ARDUINO D7
{PA_4_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 9, 0)}, // ARDUINO D7
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 10, 0)}, // ARDUINO D13 - Connected to LED1
{PA_5_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 10, 0)}, // ARDUINO D13 - Connected to LED1
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 11, 0)}, // ARDUINO D12
{PA_6_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 11, 0)}, // ARDUINO D12
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 12, 0)}, // ARDUINO D11
{PA_7_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG_ADC_CONTROL, GPIO_NOPULL, 0, 12, 0)}, // ARDUINO D11
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - Warning: pins connected to the default STDIO_UART_TX and STDIO_UART_RX pins are commented
// See https://os.mbed.com/teams/ST/wiki/STDIO for more information.
//
//==============================================================================
//*** ADC ***
MBED_WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
{PA_0_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC2_IN0
{PA_0_ALT1, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC3_IN0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 // Connected to RMII_REF_CLK [LAN8742A-CZ-TR_REFCLK0]
{PA_1_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC2_IN1 // Connected to RMII_REF_CLK [LAN8742A-CZ-TR_REFCLK0]
{PA_1_ALT1, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC3_IN1 // Connected to RMII_REF_CLK [LAN8742A-CZ-TR_REFCLK0]
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 // Connected to RMII_MDIO [LAN8742A-CZ-TR_MDIO]
{PA_2_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC2_IN2 // Connected to RMII_MDIO [LAN8742A-CZ-TR_MDIO]
{PA_2_ALT1, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC3_IN2 // Connected to RMII_MDIO [LAN8742A-CZ-TR_MDIO]
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
{PA_3_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN3
{PA_3_ALT1, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC3_IN3
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
{PA_4_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
{PA_5_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - Warning: pins connected to the default STDIO_UART_TX and STDIO_UART_RX pins are commented
// See https://os.mbed.com/teams/ST/wiki/STDIO for more information.
//
//==============================================================================
//*** ADC ***
MBED_WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 // Connected to SYS_WKUP
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
*/
#include "PeripheralPins.h"
// =============================================================================
// Notes:
// * Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// * Only the pins that are placed on the Arduino connector are described.
// =============================================================================
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC3_IN0 - ARDUINO A0
{PF_6, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC3_IN4 - ARDUINO A5
{PF_7, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC3_IN5 - ARDUINO A4
{PF_8, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC3_IN6 - ARDUINO A3
{PF_9, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC3_IN7 - ARDUINO A2
{PF_10, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC3_IN8 - ARDUINO A1
{NC, NC, 0}
};
//*** DAC ***
const PinMap PinMap_DAC[] = {
{PA_4, DAC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0xFF, 1, 0)}, // DAC_OUT1
{PA_5, DAC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0xFF, 2, 0)}, // DAC_OUT2
{NC, NC, 0}
};
*******************************************************************************
*/
#include "Arduino.h"
#include "PeripheralPins.h"
// =====
// Note: Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have to know what you do
// =====
//*** ADC ***
#ifdef HAL_ADC_MODULE_ENABLED
const PinMap PinMap_ADC[] = {
{PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
// {PA_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC2_IN0
{PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
// {PA_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC2_IN1
{PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
// {PA_2, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC2_IN2
{PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
// {PA_3, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN3
{PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
// {PA_4, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4
{PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
// {PA_5, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5
{PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
// {PA_6, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6
{PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
// {PA_7, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - Warning: pins connected to the default STDIO_UART_TX and STDIO_UART_RX pins are commented
// See https://os.mbed.com/teams/ST/wiki/STDIO for more information.
//
//==============================================================================
//*** ADC ***
MBED_WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
// {PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 // Connected to STDIO_UART_TX
// {PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 // Connected to STDIO_UART_RX
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5 // Connected to LD2 [Green Led]
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - Warning: pins connected to the default STDIO_UART_TX and STDIO_UART_RX pins are commented
// See https://os.mbed.com/teams/ST/wiki/STDIO for more information.
//
//==============================================================================
//*** ADC ***
MBED_WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
// {PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 // Connected to STDIO_UART_TX
// {PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 // Connected to STDIO_UART_RX
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9 // Connected to SMPS_EN [ADP5301ACBZ_VEN]
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10 // Connected to SMPS_V1
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11 // Connected to SMPS_PG [ADP5301ACBZ_OUTOK]
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12 // Connected to SMPS_SW [TS3A44159PWR_IN1_2]
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 16, 0)}, // ADC1_IN16
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14 // Only STM32L433RC, not STM32L433RC-P
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#include "PeripheralPins.h"
// =====
// Note: Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// =====
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - Warning: pins connected to the default STDIO_UART_TX and STDIO_UART_RX pins are commented
// See https://os.mbed.com/teams/ST/wiki/STDIO for more information.
//
//==============================================================================
//*** ADC ***
MBED_WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 // Connected to B1 [Blue PushButton]
{PA_0_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC2_IN0 // Connected to B1 [Blue PushButton]
{PA_0_ALT1, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC3_IN0 // Connected to B1 [Blue PushButton]
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 // Connected to MEMS_INT1 [L3GD20_INT1]
{PA_1_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC2_IN1 // Connected to MEMS_INT1 [L3GD20_INT1]
{PA_1_ALT1, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC3_IN1 // Connected to MEMS_INT1 [L3GD20_INT1]
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 // Connected to MEMS_INT2 [L3GD20_INT2]
{PA_2_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC2_IN2 // Connected to MEMS_INT2 [L3GD20_INT2]
{PA_2_ALT1, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC3_IN2 // Connected to MEMS_INT2 [L3GD20_INT2]
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 // Connected to B5
{PA_3_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN3 // Connected to B5
{PA_3_ALT1, ADC_3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC3_IN3 // Connected to B5
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4 // Connected to VSYNC
{PA_4_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4 // Connected to VSYNC
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
{PA_5_ALT0, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5
*/
#include "PeripheralPins.h"
// =============================================================================
// Notes:
// * Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// * Only the pins that are placed on the Arduino connector are described.
// =============================================================================
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 - ARDUINO A0
// {PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 (used by ethernet)
// {PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 (used by ethernet)
{PA_3, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN2
{PA_4, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4
{PA_5, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5 - ARDUINO D13
{PA_6, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6 - ARDUINO D12
{PA_7, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7 (used by ethernet when JP6 ON) - ARDUINO D11 (default configuration)
// {PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 (used by LED1)
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,10, 0)}, // ADC1_IN10 - ARDUINO A1
// {PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,11, 0)}, // ADC1_IN11 (used by ethernet)
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,12, 0)}, // ADC1_IN12
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,13, 0)}, // ADC1_IN13 - ARDUINO A2
// {PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,14, 0)}, // ADC1_IN14 (used by ethernet)
// {PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0,15, 0)}, // ADC1_IN15 (used by ethernet)
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#include "PeripheralPins.h"
// =====
// Note: Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// =====
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#include "PeripheralPins.h"
// =====
// Note: Commented lines are alternative possibilities which are not used per default.
// If you change them, you will have also to modify the corresponding xxx_api.c file
// for pwmout, analogin, analogout, ...
// =====
//*** ADC ***
const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 - ARDUINO A0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 - ARDUINO A1
{PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
{PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4 - ARDUINO A2
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 - ARDUINO A3
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10 - ARDUINO A5
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11 - ARDUINO A4
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
//
// - The pins which are connected to other components present on the board have
// the comment "Connected to xxx". The pin function may not work properly in this
// case. These pins may not be displayed on the board pinout image on mbed.org.
// Please read the board reference manual and schematic for more information.
//
// - Warning: pins connected to the default STDIO_UART_TX and STDIO_UART_RX pins are commented
// See https://os.mbed.com/teams/ST/wiki/STDIO for more information.
//
//==============================================================================
//*** ADC ***
MBED_WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC_IN0
{PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC_IN1
// {PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC_IN2 // Connected to STDIO_UART_TX
// {PA_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC_IN3 // Connected to STDIO_UART_RX
{PA_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC_IN4
{PA_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC_IN5 // Connected to LD2 [Green Led]
{PA_6, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC_IN6
{PA_7, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC_IN7
{PB_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC_IN8
{PB_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC_IN9
{PC_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC_IN10
{PC_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC_IN11
{PC_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC_IN12
{PC_3, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC_IN13
{PC_4, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC_IN14
{PC_5, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC_IN15
