D_PAD::D_PAD( MODULE* parent ) :
BOARD_CONNECTED_ITEM( parent, PCB_PAD_T )
{
m_NumPadName = 0;
m_Size.x = m_Size.y = DMils2iu( 600 ); // Default pad size 60 mils.
m_Drill.x = m_Drill.y = DMils2iu( 300 ); // Default drill size 30 mils.
m_Orient = 0; // Pad rotation in 1/10 degrees.
m_LengthPadToDie = 0;
if( m_Parent && m_Parent->Type() == PCB_MODULE_T )
{
m_Pos = GetParent()->GetPosition();
}
SetShape( PAD_SHAPE_CIRCLE ); // Default pad shape is PAD_CIRCLE.
SetDrillShape( PAD_DRILL_SHAPE_CIRCLE ); // Default pad drill shape is a circle.
m_Attribute = PAD_ATTRIB_STANDARD; // Default pad type is NORMAL (thru hole)
m_LocalClearance = 0;
m_LocalSolderMaskMargin = 0;
m_LocalSolderPasteMargin = 0;
m_LocalSolderPasteMarginRatio = 0.0;
m_ZoneConnection = PAD_ZONE_CONN_INHERITED; // Use parent setting by default
m_ThermalWidth = 0; // Use parent setting by default
m_ThermalGap = 0; // Use parent setting by default
// Set layers mask to default for a standard thru hole pad.
m_layerMask = StandardMask();
SetSubRatsnest( 0 ); // used in ratsnest calculations
m_boundingRadius = -1;
}
D_PAD::D_PAD( MODULE* parent ) :
BOARD_CONNECTED_ITEM( parent, PCB_PAD_T )
{
m_Size.x = m_Size.y = Mils2iu( 60 ); // Default pad size 60 mils.
m_Drill.x = m_Drill.y = Mils2iu( 30 ); // Default drill size 30 mils.
m_Orient = 0; // Pad rotation in 1/10 degrees.
m_LengthPadToDie = 0;
if( m_Parent && m_Parent->Type() == PCB_MODULE_T )
{
m_Pos = GetParent()->GetPosition();
}
SetShape( PAD_SHAPE_CIRCLE ); // Default pad shape is PAD_CIRCLE.
SetAnchorPadShape( PAD_SHAPE_CIRCLE ); // Default shape for custom shaped pads
// is PAD_CIRCLE.
SetDrillShape( PAD_DRILL_SHAPE_CIRCLE ); // Default pad drill shape is a circle.
m_Attribute = PAD_ATTRIB_STANDARD; // Default pad type is NORMAL (thru hole)
m_LocalClearance = 0;
m_LocalSolderMaskMargin = 0;
m_LocalSolderPasteMargin = 0;
m_LocalSolderPasteMarginRatio = 0.0;
// Parameters for round rect only:
m_padRoundRectRadiusScale = 0.25; // from IPC-7351C standard
// Parameters for chamfered rect only:
m_padChamferRectScale = 0.2; // Size of chamfer: ratio of smallest of X,Y size
m_chamferPositions = RECT_NO_CHAMFER; // No chamfered corner
m_ZoneConnection = PAD_ZONE_CONN_INHERITED; // Use parent setting by default
m_ThermalWidth = 0; // Use parent setting by default
m_ThermalGap = 0; // Use parent setting by default
m_customShapeClearanceArea = CUST_PAD_SHAPE_IN_ZONE_OUTLINE;
// Set layers mask to default for a standard thru hole pad.
m_layerMask = StandardMask();
SetSubRatsnest( 0 ); // used in ratsnest calculations
m_boundingRadius = -1;
}
