/**
* @brief Configure the TIMER peripheral.
* @param None
* @retval None
*/
void TIMER_Configuration(void)
{
/* TIMER1 DMA Transfer example -------------------------------------------------
TIMER1CLK = 72MHz, Prescaler = 72
TIMER1 counter clock = SystemCoreClock/72 = 1MHz.
The objective is to configure TIMER1 channel 1 to generate PWM
signal with a frequency equal to 1KHz and a variable duty cycle(25%,50%,75%) that is
changed by the DMA after a specific number of Update DMA request.
The number of this repetitive requests is defined by the TIMER1 Repetition counter,
each 2 Update Requests, the TIMER1 Channel 1 Duty Cycle changes to the next new
value defined by the buffer .
-----------------------------------------------------------------------------*/
TIMER_BaseInitPara TIMER_TimeBaseStructure;
TIMER_OCInitPara TIMER_OCInitStructure;
/* TIMERS clock enable */
RCC_APB2PeriphClock_Enable(RCC_APB2PERIPH_TIMER1|RCC_APB2PERIPH_TIMER15|RCC_APB2PERIPH_TIMER16|RCC_APB2PERIPH_TIMER17,ENABLE);
RCC_APB1PeriphClock_Enable(RCC_APB1PERIPH_TIMER2|RCC_APB1PERIPH_TIMER3|RCC_APB1PERIPH_TIMER6|RCC_APB1PERIPH_TIMER14,ENABLE);
/* TIMER1 configuration */
TIMER_DeInit(TIMER1);
TIMER_TimeBaseStructure.TIMER_Prescaler = 71;
TIMER_TimeBaseStructure.TIMER_CounterMode = TIMER_COUNTER_UP;
TIMER_TimeBaseStructure.TIMER_Period = 999;
TIMER_TimeBaseStructure.TIMER_ClockDivision = TIMER_CDIV_DIV1;
TIMER_TimeBaseStructure.TIMER_RepetitionCounter = 1;
TIMER_BaseInit(TIMER1,&TIMER_TimeBaseStructure);
/* CH1 Configuration in PWM mode */
TIMER_OCInitStructure.TIMER_OCMode = TIMER_OC_MODE_PWM1;
TIMER_OCInitStructure.TIMER_OCPolarity = TIMER_OC_POLARITY_HIGH;
TIMER_OCInitStructure.TIMER_OCNPolarity = TIMER_OCN_POLARITY_HIGH;
TIMER_OCInitStructure.TIMER_OutputState = TIMER_OUTPUT_STATE_ENABLE;
TIMER_OCInitStructure.TIMER_OutputNState = TIMER_OUTPUTN_STATE_ENABLE;
TIMER_OCInitStructure.TIMER_OCIdleState = TIMER_OC_IDLE_STATE_SET;
TIMER_OCInitStructure.TIMER_OCNIdleState = TIMER_OCN_IDLE_STATE_RESET;
TIMER_OCInitStructure.TIMER_Pulse = buffer[0];
TIMER_OC1_Init(TIMER1, &TIMER_OCInitStructure);
TIMER_OC1_Preload(TIMER1,TIMER_OC_PRELOAD_DISABLE);
/* TIMER1 output enable */
TIMER_CtrlPWMOutputs(TIMER1,ENABLE);
/* Auto-reload preload enable */
TIMER_CARLPreloadConfig(TIMER1,ENABLE);
/* TIMER1 Update DMA Request enable */
TIMER_DMACmd( TIMER1, TIMER_DMA_UPDATE, ENABLE);
/* TIMER enable counter*/
TIMER_Enable( TIMER1, ENABLE );
}
/**
* @brief Configure the TIMER peripheral.
* @param None
* @retval None
*/
void TIMER_Configuration(void)
{
/* ---------------------------------------------------------------
TIMER2 Configuration:
TIMER2CLK = SystemCoreClock / 36000 = 2K,
And generate 3 signals with 3 different delays:
TIMER2_CH1 delay = 4000/2000 = 2s
TIMER2_CH2 delay = 8000/2000 = 4s
TIMER2_CH3 delay = 12000/2000 = 6s
--------------------------------------------------------------- */
TIMER_BaseInitPara TIMER_TimeBaseStructure;
TIMER_OCInitPara TIMER_OCInitStructure;
/* TIMERS clock enable */
RCC_APB2PeriphClock_Enable(RCC_APB2PERIPH_TIMER1|RCC_APB2PERIPH_TIMER15|RCC_APB2PERIPH_TIMER16|RCC_APB2PERIPH_TIMER17,ENABLE);
RCC_APB1PeriphClock_Enable(RCC_APB1PERIPH_TIMER2|RCC_APB1PERIPH_TIMER3|RCC_APB1PERIPH_TIMER6|RCC_APB1PERIPH_TIMER14,ENABLE);
/* TIMER2 configuration */
TIMER_DeInit(TIMER2);
TIMER_TimeBaseStructure.TIMER_Prescaler = 35999;
TIMER_TimeBaseStructure.TIMER_CounterMode = TIMER_COUNTER_UP;
TIMER_TimeBaseStructure.TIMER_Period = 19999;
TIMER_TimeBaseStructure.TIMER_ClockDivision = TIMER_CDIV_DIV1;
TIMER_BaseInit(TIMER2,&TIMER_TimeBaseStructure);
/* CH1,CH2 and CH3 Configuration in OC_ACTIVE mode */
TIMER_OCInitStructure.TIMER_OCMode = TIMER_OC_MODE_ACTIVE;
TIMER_OCInitStructure.TIMER_OCPolarity = TIMER_OC_POLARITY_HIGH;
TIMER_OCInitStructure.TIMER_OutputState = TIMER_OUTPUT_STATE_ENABLE;
TIMER_OCInitStructure.TIMER_Pulse = 3999;
TIMER_OC1_Init(TIMER2, &TIMER_OCInitStructure);
TIMER_OC1_Preload(TIMER2,TIMER_OC_PRELOAD_DISABLE);
TIMER_OCInitStructure.TIMER_Pulse = 7999;
TIMER_OC2_Init(TIMER2, &TIMER_OCInitStructure);
TIMER_OC2_Preload(TIMER2,TIMER_OC_PRELOAD_DISABLE);
TIMER_OCInitStructure.TIMER_Pulse = 11999;
TIMER_OC3_Init(TIMER2, &TIMER_OCInitStructure);
TIMER_OC3_Preload(TIMER2,TIMER_OC_PRELOAD_DISABLE);
/* Auto-reload preload enable */
TIMER_CARLPreloadConfig(TIMER2,ENABLE);
/* TIMER enable counter*/
TIMER_Enable( TIMER2, ENABLE );
}
void pwm_init(void)
{
GPIO_InitPara GPIO_InitStructure;
// timer 3 pin PB1 config ( ch4 )
GPIO_InitStructure.GPIO_Pin = GPIO_PIN_1;
GPIO_InitStructure.GPIO_Mode = GPIO_MODE_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_SPEED_50MHZ;
GPIO_InitStructure.GPIO_OType = GPIO_OTYPE_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PUPD_PULLDOWN;
GPIO_Init(GPIOB,&GPIO_InitStructure);
GPIO_PinAFConfig(GPIOB,GPIO_PINSOURCE1,GPIO_AF_1);
// GPIO pins PA8 , 9 ,10 setup ( Timer1 ch 1 , 2 , 3)
GPIO_InitStructure.GPIO_Pin = GPIO_PIN_8|GPIO_PIN_9|GPIO_PIN_10;
GPIO_Init(GPIOA,&GPIO_InitStructure);
GPIO_PinAFConfig(GPIOA,GPIO_PINSOURCE8,GPIO_AF_2);
GPIO_PinAFConfig(GPIOA,GPIO_PINSOURCE9,GPIO_AF_2);
GPIO_PinAFConfig(GPIOA,GPIO_PINSOURCE10,GPIO_AF_2);
TIMER_BaseInitPara TIM_TimeBaseStructure;
RCC_APB2PeriphClock_Enable(RCC_APB2PERIPH_TIMER1,ENABLE);
RCC_APB1PeriphClock_Enable(RCC_APB1PERIPH_TIMER3,ENABLE);
// TIMER3 for pins A8 A9 A10
TIM_TimeBaseStructure.TIMER_Prescaler = TIMER_PRESCALER - 1; //
TIM_TimeBaseStructure.TIMER_CounterMode = TIMER_COUNTER_UP;
TIM_TimeBaseStructure.TIMER_Period = PWMTOP;
TIM_TimeBaseStructure.TIMER_ClockDivision = TIMER_CDIV_DIV1;
TIMER_BaseInit(TIMER3,&TIM_TimeBaseStructure);
//Ch1 , 2 , 3
TIM_OCInitStructure.TIMER_OCMode = TIMER_OC_MODE_PWM1;
TIM_OCInitStructure.TIMER_OCPolarity = OUT_POLARITY;
TIM_OCInitStructure.TIMER_OutputState = TIMER_OUTPUT_STATE_ENABLE;
TIM_OCInitStructure.TIMER_OCIdleState = TIMER_OC_IDLE_STATE_RESET;
TIM_OCInitStructure.TIMER_Pulse = 0;
TIMER_OC4_Init(TIMER3, &TIM_OCInitStructure);
TIMER_CtrlPWMOutputs(TIMER3,ENABLE);
TIMER_CARLPreloadConfig(TIMER3,ENABLE);
TIMER_Enable( TIMER3, ENABLE );
TIMER_BaseInit(TIMER1,&TIM_TimeBaseStructure);
TIMER_OC1_Init(TIMER1, &TIM_OCInitStructure);
TIMER_OC2_Init(TIMER1, &TIM_OCInitStructure);
TIMER_OC3_Init(TIMER1, &TIM_OCInitStructure);
TIMER_CtrlPWMOutputs(TIMER1,ENABLE);
TIMER_CARLPreloadConfig(TIMER1,ENABLE);
TIMER_OC1_Preload(TIMER1,ESC_PRELOAD);
TIMER_OC2_Preload(TIMER1,ESC_PRELOAD);
TIMER_OC3_Preload(TIMER1,ESC_PRELOAD);
TIMER_OC4_Preload(TIMER3,ESC_PRELOAD);
TIMER_Enable( TIMER1, ENABLE );
}
void pwm_init(void)
{
GPIO_InitPara GPIO_InitStructure;
//pin A0 TM2_ch1
GPIO_InitStructure.GPIO_Pin = GPIO_PIN_1;
GPIO_InitStructure.GPIO_Mode = GPIO_MODE_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_SPEED_50MHZ;
GPIO_InitStructure.GPIO_OType = GPIO_OTYPE_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PUPD_PULLDOWN;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_PinAFConfig(GPIOA, GPIO_PINSOURCE1, GPIO_AF_2);
TIMER_BaseInitPara TIM_TimeBaseStructure;
RCC_APB1PeriphClock_Enable(RCC_APB1PERIPH_TIMER2 |
RCC_APB1PERIPH_TIMER14 |
RCC_APB1PERIPH_TIMER3, ENABLE);
RCC_APB2PeriphClock_Enable(RCC_APB2PERIPH_TIMER1, ENABLE);
// timer 2
TIM_TimeBaseStructure.TIMER_Prescaler = TIMER_PRESCALER - 1; //
TIM_TimeBaseStructure.TIMER_CounterMode = TIMER_COUNTER_CENTER_ALIGNED2;
TIM_TimeBaseStructure.TIMER_Period = PWMTOP;
TIM_TimeBaseStructure.TIMER_ClockDivision = TIMER_CDIV_DIV1;
// init timer 2
TIMER_BaseInit(TIMER2, &TIM_TimeBaseStructure);
TIM_OCInitStructure.TIMER_OCMode = TIMER_OC_MODE_PWM1;
TIM_OCInitStructure.TIMER_OCPolarity = TIMER_OC_POLARITY_HIGH;
TIM_OCInitStructure.TIMER_OutputState = TIMER_OUTPUT_STATE_ENABLE;
TIM_OCInitStructure.TIMER_OCIdleState = TIMER_OC_IDLE_STATE_RESET;
TIM_OCInitStructure.TIMER_Pulse = 0;
TIMER_OC2_Init(TIMER2, &TIM_OCInitStructure);
TIMER_CtrlPWMOutputs(TIMER2, ENABLE);
TIMER_CARLPreloadConfig(TIMER2, ENABLE);
TIMER_OC2_Preload(TIMER2, TIMER_OC_PRELOAD_DISABLE);
// pin A3
GPIO_InitStructure.GPIO_Pin = GPIO_PIN_3;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_PinAFConfig(GPIOA, GPIO_PINSOURCE3, GPIO_AF_2);
TIMER_OC4_Init(TIMER2, &TIM_OCInitStructure);
TIMER_OC4_Preload(TIMER2, TIMER_OC_PRELOAD_DISABLE);
// TIMER_Enable( TIMER2, ENABLE );
// timer 1 ch3 , ch1
// pins A10 , A8
GPIO_InitStructure.GPIO_Pin = GPIO_PIN_10 | GPIO_PIN_8;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_PinAFConfig(GPIOA, GPIO_PINSOURCE10, GPIO_AF_2);
GPIO_PinAFConfig(GPIOA, GPIO_PINSOURCE8, GPIO_AF_2);
// timer 1
// init timer 1
TIMER_BaseInit(TIMER1, &TIM_TimeBaseStructure);
TIM_OCInitStructure.TIMER_Pulse = 0;
TIMER_OC3_Init(TIMER1, &TIM_OCInitStructure);
TIMER_OC1_Init(TIMER1, &TIM_OCInitStructure);
TIMER_CtrlPWMOutputs(TIMER1, ENABLE);
TIMER_CARLPreloadConfig(TIMER1, ENABLE);
TIMER_OC3_Preload(TIMER1, TIMER_OC_PRELOAD_DISABLE);
TIMER_OC1_Preload(TIMER1, TIMER_OC_PRELOAD_DISABLE);
// bridge dir 2
///////////////
//pin A9 TM1_ch2
GPIO_InitStructure.GPIO_Pin = GPIO_PIN_9;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_PinAFConfig(GPIOA, GPIO_PINSOURCE9, GPIO_AF_2);
// timer 1
// init timer 1
TIMER_BaseInit(TIMER1, &TIM_TimeBaseStructure);
TIM_OCInitStructure.TIMER_Pulse = 0;
TIMER_OC2_Init(TIMER2, &TIM_OCInitStructure);
TIMER_CtrlPWMOutputs(TIMER1, ENABLE);
TIMER_CARLPreloadConfig(TIMER1, ENABLE);
TIMER_OC2_Preload(TIMER1, TIMER_OC_PRELOAD_DISABLE);
// timer 3 PB1 af1 ch4
GPIO_InitStructure.GPIO_Pin = GPIO_PIN_1;
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_PinAFConfig(GPIOB, GPIO_PINSOURCE1, GPIO_AF_1);
// timer 3
// init timer 3
TIMER_BaseInit(TIMER3, &TIM_TimeBaseStructure);
TIM_OCInitStructure.TIMER_Pulse = 0;
TIMER_OC4_Init(TIMER3, &TIM_OCInitStructure);
TIMER_CtrlPWMOutputs(TIMER3, ENABLE);
TIMER_CARLPreloadConfig(TIMER3, ENABLE);
TIMER_OC4_Preload(TIMER3, TIMER_OC_PRELOAD_DISABLE);
// A0
// Timer2 ch1
GPIO_InitStructure.GPIO_Pin = GPIO_PIN_0;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_PinAFConfig(GPIOA, GPIO_PINSOURCE0, GPIO_AF_2);
// timer 2
// init timer 2
TIMER_BaseInit(TIMER2, &TIM_TimeBaseStructure);
TIM_OCInitStructure.TIMER_Pulse = 0;
TIMER_OC1_Init(TIMER2, &TIM_OCInitStructure);
TIMER_CtrlPWMOutputs(TIMER2, ENABLE);
TIMER_CARLPreloadConfig(TIMER2, ENABLE);
TIMER_OC1_Preload(TIMER2, TIMER_OC_PRELOAD_DISABLE);
// PA2 tm2 ch3
GPIO_InitStructure.GPIO_Pin = GPIO_PIN_2;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_PinAFConfig(GPIOA, GPIO_PINSOURCE2, GPIO_AF_2);
TIMER_OC3_Init(TIMER2, &TIM_OCInitStructure);
TIMER_OC3_Preload(TIMER2, TIMER_OC_PRELOAD_DISABLE);
TIMER_Enable(TIMER3, ENABLE);
TIMER_Enable(TIMER1, ENABLE);
TIMER_Enable(TIMER2, ENABLE);
}
