/**
*
* This function initializes the controller for the QSPI interface.
*
* @param None
*
* @return None
*
* @note None
*
****************************************************************************/
u32 InitQspi(void)
{
XQspiPs_Config *QspiConfig;
int Status;
QspiInstancePtr = &QspiInstance;
/*
* Set up the base address for access
*/
FlashReadBaseAddress = XPS_QSPI_LINEAR_BASEADDR;
/*
* Initialize the QSPI driver so that it's ready to use
*/
QspiConfig = XQspiPs_LookupConfig(QSPI_DEVICE_ID);
if (NULL == QspiConfig) {
return XST_FAILURE;
}
Status = XQspiPs_CfgInitialize(QspiInstancePtr, QspiConfig,
QspiConfig->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set Manual Chip select options and drive HOLD_B pin high.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_FORCE_SSELECT_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
/*
* Set the prescaler for QSPI clock
*/
XQspiPs_SetClkPrescaler(QspiInstancePtr, XQSPIPS_CLK_PRESCALE_8);
/*
* Assert the FLASH chip select.
*/
XQspiPs_SetSlaveSelect(QspiInstancePtr);
/*
* Read Flash ID and extract Manufacture and Size information
*/
Status = FlashReadID();
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
if (XPAR_PS7_QSPI_0_QSPI_MODE == SINGLE_FLASH_CONNECTION) {
fsbl_printf(DEBUG_INFO,"QSPI is in single flash connection\r\n");
/*
* For Flash size <128Mbit controller configured in linear mode
*/
if (QspiFlashSize <= FLASH_SIZE_16MB) {
LinearBootDeviceFlag = 1;
/*
* Enable linear mode
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_LQSPI_MODE_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
/*
* Single linear read
*/
XQspiPs_SetLqspiConfigReg(QspiInstancePtr, SINGLE_QSPI_CONFIG_QUAD_READ);
/*
* Enable the controller
*/
XQspiPs_Enable(QspiInstancePtr);
} else {
/*
* Single flash IO read
*/
XQspiPs_SetLqspiConfigReg(QspiInstancePtr, SINGLE_QSPI_IO_CONFIG_QUAD_READ);
/*
* Enable the controller
*/
XQspiPs_Enable(QspiInstancePtr);
}
}
if (XPAR_PS7_QSPI_0_QSPI_MODE == DUAL_PARALLEL_CONNECTION) {
fsbl_printf(DEBUG_INFO,"QSPI is in Dual Parallel connection\r\n");
/*
* For Single Flash size <128Mbit controller configured in linear mode
*/
if (QspiFlashSize <= FLASH_SIZE_16MB) {
/*
* Setting linear access flag
*/
LinearBootDeviceFlag = 1;
/*
* Enable linear mode
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_LQSPI_MODE_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
/*
* Dual linear read
*/
XQspiPs_SetLqspiConfigReg(QspiInstancePtr, DUAL_QSPI_CONFIG_QUAD_READ);
/*
* Enable the controller
*/
XQspiPs_Enable(QspiInstancePtr);
} else {
/*
* Dual flash IO read
*/
XQspiPs_SetLqspiConfigReg(QspiInstancePtr, DUAL_QSPI_IO_CONFIG_QUAD_READ);
/*
* Enable the controller
*/
XQspiPs_Enable(QspiInstancePtr);
}
/*
* Total flash size is two time of single flash size
*/
QspiFlashSize = 2 * QspiFlashSize;
}
/*
* It is expected to same flash size for both chip selection
*/
if (XPAR_PS7_QSPI_0_QSPI_MODE == DUAL_STACK_CONNECTION) {
fsbl_printf(DEBUG_INFO,"QSPI is in Dual Stack connection\r\n");
QspiFlashSize = 2 * QspiFlashSize;
/*
* Enable two flash memories on separate buses
*/
XQspiPs_SetLqspiConfigReg(QspiInstancePtr, DUAL_STACK_CONFIG_READ);
}
return XST_SUCCESS;
}
/*****************************************************************************
*
* The purpose of this function is to illustrate how to use the XQspiPs
* device driver in single, parallel and stacked modes using
* flash devices greater than 128Mb.
* This function reads and writes data in I/O mode.
*
* @param None.
*
* @return XST_SUCCESS if successful, else XST_FAILURE.
*
* @note None.
*
*****************************************************************************/
int QspiG128FlashExample(XQspiPs *QspiInstancePtr, u16 QspiDeviceId)
{
int Status;
u8 UniqueValue;
int Count;
int Page;
XQspiPs_Config *QspiConfig;
/*
* Initialize the QSPI driver so that it's ready to use
*/
QspiConfig = XQspiPs_LookupConfig(QspiDeviceId);
if (NULL == QspiConfig) {
return XST_FAILURE;
}
Status = XQspiPs_CfgInitialize(QspiInstancePtr, QspiConfig,
QspiConfig->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform a self-test to check hardware build
*/
Status = XQspiPs_SelfTest(QspiInstancePtr);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set the pre-scaler for QSPI clock
*/
XQspiPs_SetClkPrescaler(QspiInstancePtr, XQSPIPS_CLK_PRESCALE_8);
/*
* Set Manual Start and Manual Chip select options and drive the
* HOLD_B high.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_FORCE_SSELECT_OPTION |
XQSPIPS_MANUAL_START_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
if(QspiConfig->ConnectionMode == XQSPIPS_CONNECTION_MODE_STACKED) {
/*
* Enable two flash memories, Shared bus (NOT separate bus),
* L_PAGE selected by default
*/
XQspiPs_SetLqspiConfigReg(QspiInstancePtr, DUAL_STACK_CONFIG_WRITE);
}
if(QspiConfig->ConnectionMode == XQSPIPS_CONNECTION_MODE_PARALLEL) {
/*
* Enable two flash memories on separate buses
*/
XQspiPs_SetLqspiConfigReg(QspiInstancePtr, DUAL_QSPI_CONFIG_WRITE);
}
/*
* Assert the Flash chip select.
*/
XQspiPs_SetSlaveSelect(QspiInstancePtr);
/*
* Read flash ID and obtain all flash related information
* It is important to call the read id function before
* performing proceeding to any operation, including
* preparing the WriteBuffer
*/
FlashReadID(QspiInstancePtr, WriteBuffer, ReadBuffer);
/*
* Initialize MaxData according to page size.
*/
MaxData = PAGE_COUNT * (Flash_Config_Table[FCTIndex].PageSize);
/*
* Initialize the write buffer for a pattern to write to the Flash
* and the read buffer to zero so it can be verified after the read, the
* test value that is added to the unique value allows the value to be
* changed in a debug environment to guarantee
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0;
Count < Flash_Config_Table[FCTIndex].PageSize;
Count++, UniqueValue++) {
WriteBuffer[DATA_OFFSET + Count] = (u8)(UniqueValue + Test);
}
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
/*
* Erase the flash.
*/
FlashErase(QspiInstancePtr, TEST_ADDRESS, MaxData, WriteBuffer);
/*
* Write the data in the write buffer to the serial Flash a page at a
* time, starting from TEST_ADDRESS
*/
for (Page = 0; Page < PAGE_COUNT; Page++) {
FlashWrite(QspiInstancePtr,
(Page * Flash_Config_Table[FCTIndex].PageSize) + TEST_ADDRESS,
Flash_Config_Table[FCTIndex].PageSize, WRITE_CMD, WriteBuffer);
}
/*
* I/O Read - for any flash size
*/
FlashRead(QspiInstancePtr, TEST_ADDRESS, MaxData, QUAD_READ_CMD,
WriteBuffer, ReadBuffer);
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MaxData;
Count++, UniqueValue++) {
if (ReadBuffer[Count] != (u8)(UniqueValue + Test)) {
return XST_FAILURE;
}
}
/*
* Initialize the write buffer for a pattern to write to the Flash
* and the read buffer to zero so it can be verified after the read, the
* test value that is added to the unique value allows the value to be
* changed in a debug environment to guarantee
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0;
Count < Flash_Config_Table[FCTIndex].PageSize;
Count++, UniqueValue++) {
WriteBuffer[DATA_OFFSET + Count] = (u8)(UniqueValue + Test);
}
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
/*
* Set Auto Start and Manual Chip select options and drive the
* HOLD_B high.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_FORCE_SSELECT_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
/*
* Erase the flash.
*/
FlashErase(QspiInstancePtr, TEST_ADDRESS, MaxData, WriteBuffer);
/*
* Write the data in the write buffer to the serial Flash a page at a
* time, starting from TEST_ADDRESS
*/
for (Page = 0; Page < PAGE_COUNT; Page++) {
FlashWrite(QspiInstancePtr,
(Page * Flash_Config_Table[FCTIndex].PageSize) + TEST_ADDRESS,
Flash_Config_Table[FCTIndex].PageSize, WRITE_CMD, WriteBuffer);
}
/*
* I/O Read - for any flash size
*/
FlashRead(QspiInstancePtr, TEST_ADDRESS, MaxData, QUAD_READ_CMD,
WriteBuffer, ReadBuffer);
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MaxData;
Count++, UniqueValue++) {
if (ReadBuffer[Count] != (u8)(UniqueValue + Test)) {
return XST_FAILURE;
}
}
return XST_SUCCESS;
}
/*****************************************************************************
*
* The purpose of this function is to illustrate how to use the XQspiPs
* device driver in Linear mode. This function writes data to the serial
* FLASH in QSPI mode and reads data in Linear QSPI mode.
*
* @param None.
*
* @return XST_SUCCESS if successful, else XST_FAILURE.
*
* @note None.
*
*****************************************************************************/
int LinearQspiFlashExample(XQspiPs *QspiInstancePtr, u16 QspiDeviceId)
{
int Status;
u8 UniqueValue;
int Count;
int Page;
XQspiPs_Config *QspiConfig;
/*
* Initialize the QSPI driver so that it's ready to use
*/
QspiConfig = XQspiPs_LookupConfig(QspiDeviceId);
if (NULL == QspiConfig) {
return XST_FAILURE;
}
Status = XQspiPs_CfgInitialize(QspiInstancePtr, QspiConfig,
QspiConfig->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform a self-test to check hardware build
*/
Status = XQspiPs_SelfTest(QspiInstancePtr);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Enable two flash memories on seperate buses
*/
XQspiPs_SetLqspiConfigReg(QspiInstancePtr, DUAL_QSPI_CONFIG_WRITE);
/*
* Set the QSPI device as a master and enable manual CS, manual start
* and flash interface mode options and drive HOLD_B pin high.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_FORCE_SSELECT_OPTION |
XQSPIPS_MANUAL_START_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
XQspiPs_SetClkPrescaler(QspiInstancePtr, XQSPIPS_CLK_PRESCALE_8);
/*
* Initialize the write buffer for a pattern to write to the FLASH
* and the read buffer to zero so it can be verified after the read, the
* test value that is added to the unique value allows the value to be
* changed in a debug environment to guarantee
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < PAGE_SIZE;
Count++, UniqueValue++) {
WriteBuffer[DATA_OFFSET + Count] = (u8)(UniqueValue + Test);
}
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
/*
* Assert the FLASH chip select.
*/
XQspiPs_SetSlaveSelect(QspiInstancePtr);
/*
* Erase the flash sectors
*/
FlashErase(QspiInstancePtr, TEST_ADDRESS, MAX_DATA);
/*
* Write data to the two flash memories on seperate buses, starting from
* TEST_ADDRESS. This is same as writing to a single flash memory. The
* LQSPI controller takes care of splitting the data words and writing
* them to the two flash memories. The user needs to take care of the
* address translation
*/
for (Page = 0; Page < PAGE_COUNT; Page++) {
FlashWrite(QspiInstancePtr, ((Page * PAGE_SIZE) +
TEST_ADDRESS) / 2, PAGE_SIZE, WRITE_CMD);
}
/*
* Read from the two flash memories on seperate buses in LQSPI mode.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_LQSPI_MODE_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
XQspiPs_SetLqspiConfigReg(QspiInstancePtr, DUAL_QSPI_CONFIG_QUAD_READ);
Status = XQspiPs_LqspiRead(QspiInstancePtr, ReadBuffer, TEST_ADDRESS,
MAX_DATA);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MAX_DATA;
Count++, UniqueValue++) {
if (ReadBuffer[Count] != WriteBuffer[DATA_OFFSET +
(Count % PAGE_SIZE)]) {
return XST_FAILURE;
}
}
/*
* Set the QSPI device as a master and enable manual CS, manual start
* and flash interface mode options and drive HOLD_B pin high.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_FORCE_SSELECT_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
/*
* Initialize the write buffer for a pattern to write to the FLASH
* and the read buffer to zero so it can be verified after the read, the
* test value that is added to the unique value allows the value to be
* changed in a debug environment to guarantee
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < PAGE_SIZE;
Count++, UniqueValue++) {
WriteBuffer[DATA_OFFSET + Count] = (u8)(UniqueValue + Test);
}
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
/*
* Erase the flash sectors
*/
FlashErase(QspiInstancePtr, TEST_ADDRESS, MAX_DATA);
/*
* Write data to the two flash memories on seperate buses, starting from
* TEST_ADDRESS. This is same as writing to a single flash memory. The
* LQSPI controller takes care of splitting the data words and writing
* them to the two flash memories. The user needs to take care of the
* address translation
*/
for (Page = 0; Page < PAGE_COUNT; Page++) {
FlashWrite(QspiInstancePtr, ((Page * PAGE_SIZE) +
TEST_ADDRESS) / 2, PAGE_SIZE, WRITE_CMD);
}
/*
* Read from the two flash memories on seperate buses in LQSPI mode.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_LQSPI_MODE_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
XQspiPs_SetLqspiConfigReg(QspiInstancePtr, DUAL_QSPI_CONFIG_QUAD_READ);
Status = XQspiPs_LqspiRead(QspiInstancePtr, ReadBuffer, TEST_ADDRESS,
MAX_DATA);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MAX_DATA;
Count++, UniqueValue++) {
if (ReadBuffer[Count] != WriteBuffer[DATA_OFFSET +
(Count % PAGE_SIZE)]) {
return XST_FAILURE;
}
}
return XST_SUCCESS;
}
/*****************************************************************************
*
* The purpose of this function is to illustrate how to use the XQspiPs
* device driver in Linear mode. This function writes data to the serial
* FLASH in QSPI mode and reads data in Linear QSPI mode.
*
* @param None.
*
* @return XST_SUCCESS if successful, else XST_FAILURE.
*
* @note None.
*
*****************************************************************************/
int LinearQspiFlashExample(XQspiPs *QspiInstancePtr, u16 QspiDeviceId)
{
int Status;
u8 UniqueValue;
int Count;
int Page;
XQspiPs_Config *QspiConfig;
/*
* Initialize the QSPI driver so that it's ready to use
*/
QspiConfig = XQspiPs_LookupConfig(QspiDeviceId);
if (NULL == QspiConfig) {
return XST_FAILURE;
}
Status = XQspiPs_CfgInitialize(QspiInstancePtr, QspiConfig,
QspiConfig->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform a self-test to check hardware build
*/
Status = XQspiPs_SelfTest(QspiInstancePtr);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Initialize the write buffer for a pattern to write to the FLASH
* and the read buffer to zero so it can be verified after the read, the
* test value that is added to the unique value allows the value to be
* changed in a debug environment to guarantee
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < PAGE_SIZE;
Count++, UniqueValue++) {
WriteBuffer[DATA_OFFSET + Count] = (u8)(UniqueValue + Test);
}
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
/*
* Set the prescaler for QSPI clock
*/
XQspiPs_SetClkPrescaler(QspiInstancePtr, XQSPIPS_CLK_PRESCALE_8);
/*
* Set Manual Start and Manual Chip select options and drive the
* HOLD_B high.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_FORCE_SSELECT_OPTION |
XQSPIPS_MANUAL_START_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
/*
* Assert the FLASH chip select.
*/
XQspiPs_SetSlaveSelect(QspiInstancePtr);
FlashReadID();
/*
* Erase the flash.
*/
FlashErase(QspiInstancePtr, TEST_ADDRESS, MAX_DATA);
/*
* Write the data in the write buffer to the serial FLASH a page at a
* time, starting from TEST_ADDRESS
*/
for (Page = 0; Page < PAGE_COUNT; Page++) {
FlashWrite(QspiInstancePtr, (Page * PAGE_SIZE) + TEST_ADDRESS,
PAGE_SIZE, WRITE_CMD);
}
/*
* Read from the flash in LQSPI mode.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_LQSPI_MODE_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
Status = XQspiPs_LqspiRead(QspiInstancePtr, ReadBuffer, TEST_ADDRESS,
MAX_DATA);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MAX_DATA;
Count++, UniqueValue++) {
if (ReadBuffer[Count] != (u8)(UniqueValue + Test)) {
return XST_FAILURE;
}
}
/*
* Initialize the write buffer for a pattern to write to the FLASH
* and the read buffer to zero so it can be verified after the read, the
* test value that is added to the unique value allows the value to be
* changed in a debug environment to guarantee
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < PAGE_SIZE;
Count++, UniqueValue++) {
WriteBuffer[DATA_OFFSET + Count] = (u8)(UniqueValue + Test);
}
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
/*
* Set Auto Start and Manual Chip select options and drive the
* HOLD_B high.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_FORCE_SSELECT_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
/*
* Erase the flash.
*/
FlashErase(QspiInstancePtr, TEST_ADDRESS, MAX_DATA);
/*
* Write the data in the write buffer to the serial FLASH a page at a
* time, starting from TEST_ADDRESS
*/
for (Page = 0; Page < PAGE_COUNT; Page++) {
FlashWrite(QspiInstancePtr, (Page * PAGE_SIZE) + TEST_ADDRESS,
PAGE_SIZE, WRITE_CMD);
}
/*
* Read from the flash in LQSPI mode.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_LQSPI_MODE_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
Status = XQspiPs_LqspiRead(QspiInstancePtr, ReadBuffer, TEST_ADDRESS,
MAX_DATA);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MAX_DATA;
Count++, UniqueValue++) {
if (ReadBuffer[Count] != (u8)(UniqueValue + Test)) {
return XST_FAILURE;
}
}
return XST_SUCCESS;
}
/*****************************************************************************
*
* The purpose of this function is to illustrate how to use the XQspiPs
* device driver in interrupt mode. This function writes and reads data
* from a serial FLASH.
*
* @param None.
*
* @return XST_SUCCESS if successful else XST_FAILURE.
*
* @note
*
* This function calls other functions which contain loops that may be infinite
* if interrupts are not working such that it may not return. If the device
* slave select is not correct and the device is not responding on bus it will
* read a status of 0xFF for the status register as the bus is pulled up.
*
*****************************************************************************/
int QspiFlashIntrExample(XScuGic *IntcInstancePtr, XQspiPs *QspiInstancePtr,
u16 QspiDeviceId, u16 QspiIntrId)
{
int Status;
u8 *BufferPtr;
u8 UniqueValue;
int Count;
int Page;
XQspiPs_Config *QspiConfig;
/*
* Initialize the QSPI driver so that it's ready to use
*/
QspiConfig = XQspiPs_LookupConfig(QspiDeviceId);
if (NULL == QspiConfig) {
return XST_FAILURE;
}
Status = XQspiPs_CfgInitialize(QspiInstancePtr, QspiConfig,
QspiConfig->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform a self-test to check hardware build
*/
Status = XQspiPs_SelfTest(QspiInstancePtr);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Connect the Qspi device to the interrupt subsystem such that
* interrupts can occur. This function is application specific
*/
Status = QspiSetupIntrSystem(IntcInstancePtr, QspiInstancePtr,
QspiIntrId);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup the handler for the QSPI that will be called from the
* interrupt context when an QSPI status occurs, specify a pointer to
* the QSPI driver instance as the callback reference so the handler is
* able to access the instance data
*/
XQspiPs_SetStatusHandler(QspiInstancePtr, QspiInstancePtr,
(XQspiPs_StatusHandler) QspiHandler);
/*
* Set Manual Start and Manual Chip select options and drive the
* HOLD_B high.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_FORCE_SSELECT_OPTION |
XQSPIPS_MANUAL_START_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
/*
* Set the operating clock frequency using the clock divider
*/
XQspiPs_SetClkPrescaler(QspiInstancePtr, XQSPIPS_CLK_PRESCALE_8);
/*
* Assert the FLASH chip select
*/
XQspiPs_SetSlaveSelect(QspiInstancePtr);
/*
* Initialize the write buffer for a pattern to write to the FLASH
* and the read buffer to zero so it can be verified after the read, the
* test value that is added to the unique value allows the value to be
* changed in a debug environment to guarantee
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < PAGE_SIZE;
Count++, UniqueValue++) {
WriteBuffer[DATA_OFFSET + Count] = (u8)(UniqueValue + Test);
}
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
FlashReadID();
/*
* Erase the flash.
*/
FlashErase(QspiInstancePtr, TEST_ADDRESS, MAX_DATA);
/*
* Write the data in the write buffer to the serial FLASH a page at a
* time, starting from TEST_ADDRESS
*/
for (Page = 0; Page < PAGE_COUNT; Page++) {
FlashWrite(QspiInstancePtr, (Page * PAGE_SIZE) + TEST_ADDRESS,
PAGE_SIZE, WRITE_CMD);
}
/*
* Read the contents of the FLASH from TEST_ADDRESS, using Normal Read
* command.
*/
FlashRead(QspiInstancePtr, TEST_ADDRESS, MAX_DATA, READ_CMD);
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
BufferPtr = &ReadBuffer[DATA_OFFSET];
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MAX_DATA;
Count++, UniqueValue++) {
if (BufferPtr[Count] != (u8)(UniqueValue + Test)) {
return XST_FAILURE;
}
}
/*
* Read the contents of the FLASH from TEST_ADDRESS, using Fast Read
* command
*/
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
FlashRead(QspiInstancePtr, TEST_ADDRESS, MAX_DATA, FAST_READ_CMD);
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
BufferPtr = &ReadBuffer[DATA_OFFSET + DUMMY_SIZE];
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MAX_DATA;
Count++, UniqueValue++) {
if (BufferPtr[Count] != (u8)(UniqueValue + Test)) {
return XST_FAILURE;
}
}
/*
* Read the contents of the FLASH from TEST_ADDRESS, using Dual Read
* command
*/
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
FlashRead(QspiInstancePtr, TEST_ADDRESS, MAX_DATA, DUAL_READ_CMD);
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
BufferPtr = &ReadBuffer[DATA_OFFSET + DUMMY_SIZE];
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MAX_DATA;
Count++, UniqueValue++) {
if (BufferPtr[Count] != (u8)(UniqueValue + Test)) {
return XST_FAILURE;
}
}
/*
* Read the contents of the FLASH from TEST_ADDRESS, using Quad Read
* command
*/
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
FlashRead(QspiInstancePtr, TEST_ADDRESS, MAX_DATA, QUAD_READ_CMD);
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
BufferPtr = &ReadBuffer[DATA_OFFSET + DUMMY_SIZE];
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MAX_DATA;
Count++, UniqueValue++) {
if (BufferPtr[Count] != (u8)(UniqueValue + Test)) {
return XST_FAILURE;
}
}
/*
* Set Auto Start and Manual Chip select options and drive the
* HOLD_B high.
*/
XQspiPs_SetOptions(QspiInstancePtr, XQSPIPS_FORCE_SSELECT_OPTION |
XQSPIPS_HOLD_B_DRIVE_OPTION);
/*
* Initialize the write buffer for a pattern to write to the FLASH
* and the read buffer to zero so it can be verified after the read, the
* test value that is added to the unique value allows the value to be
* changed in a debug environment to guarantee
*/
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < PAGE_SIZE;
Count++, UniqueValue++) {
WriteBuffer[DATA_OFFSET + Count] = (u8)(UniqueValue + Test);
}
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
/*
* Erase the flash.
*/
FlashErase(QspiInstancePtr, TEST_ADDRESS, MAX_DATA);
/*
* Write the data in the write buffer to the serial FLASH a page at a
* time, starting from TEST_ADDRESS
*/
for (Page = 0; Page < PAGE_COUNT; Page++) {
FlashWrite(QspiInstancePtr, (Page * PAGE_SIZE) + TEST_ADDRESS,
PAGE_SIZE, WRITE_CMD);
}
/*
* Read the contents of the FLASH from TEST_ADDRESS, using Normal Read
* command.
*/
FlashRead(QspiInstancePtr, TEST_ADDRESS, MAX_DATA, READ_CMD);
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
BufferPtr = &ReadBuffer[DATA_OFFSET];
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MAX_DATA;
Count++, UniqueValue++) {
if (BufferPtr[Count] != (u8)(UniqueValue + Test)) {
return XST_FAILURE;
}
}
/*
* Read the contents of the FLASH from TEST_ADDRESS, using Fast Read
* command
*/
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
FlashRead(QspiInstancePtr, TEST_ADDRESS, MAX_DATA, FAST_READ_CMD);
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
BufferPtr = &ReadBuffer[DATA_OFFSET + DUMMY_SIZE];
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MAX_DATA;
Count++, UniqueValue++) {
if (BufferPtr[Count] != (u8)(UniqueValue + Test)) {
return XST_FAILURE;
}
}
/*
* Read the contents of the FLASH from TEST_ADDRESS, using Dual Read
* command
*/
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
FlashRead(QspiInstancePtr, TEST_ADDRESS, MAX_DATA, DUAL_READ_CMD);
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
BufferPtr = &ReadBuffer[DATA_OFFSET + DUMMY_SIZE];
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MAX_DATA;
Count++, UniqueValue++) {
if (BufferPtr[Count] != (u8)(UniqueValue + Test)) {
return XST_FAILURE;
}
}
/*
* Read the contents of the FLASH from TEST_ADDRESS, using Quad Read
* command
*/
memset(ReadBuffer, 0x00, sizeof(ReadBuffer));
FlashRead(QspiInstancePtr, TEST_ADDRESS, MAX_DATA, QUAD_READ_CMD);
/*
* Setup a pointer to the start of the data that was read into the read
* buffer and verify the data read is the data that was written
*/
BufferPtr = &ReadBuffer[DATA_OFFSET + DUMMY_SIZE];
for (UniqueValue = UNIQUE_VALUE, Count = 0; Count < MAX_DATA;
Count++, UniqueValue++) {
if (BufferPtr[Count] != (u8)(UniqueValue + Test)) {
return XST_FAILURE;
}
}
QspiDisableIntrSystem(IntcInstancePtr, QspiIntrId);
return XST_SUCCESS;
}