int DPG1_SPIInit(XSpi *SpiInstancePtr){
int Status;
Status = XSpi_CfgInitialize(SpiInstancePtr, &DPG1Config, DPG1Config.BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
Status = XSpi_SetOptions(SpiInstancePtr, (XSP_MASTER_OPTION | XSP_CLK_ACTIVE_LOW_OPTION | XSP_CLK_PHASE_1_OPTION) | XSP_MANUAL_SSELECT_OPTION);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
Status = XSpi_SetSlaveSelect(SpiInstancePtr, 1);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Start the SPI driver so that the device is enabled.
*/
XSpi_Start(SpiInstancePtr);
/*
* Disable Global interrupt to use polled mode operation
*/
XSpi_IntrGlobalDisable(SpiInstancePtr);
return XST_SUCCESS;
}
int init_spi(XSpi *SpiInstancePtr){
int Status;
XSpi_Config *ConfigPtr; /* Pointer to Configuration data */
ConfigPtr = XSpi_LookupConfig(SPI_DEVICE_ID);
if (ConfigPtr == NULL) {
return XST_DEVICE_NOT_FOUND;
}
Status = XSpi_CfgInitialize(SpiInstancePtr, ConfigPtr,
ConfigPtr->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
Status = XSpi_SelfTest(SpiInstancePtr);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
if (SpiInstancePtr->SpiMode != XSP_STANDARD_MODE) {
return XST_SUCCESS;
}
Status = XSpi_SetOptions(SpiInstancePtr, XSP_MASTER_OPTION);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
XSpi_Start(SpiInstancePtr);
XSpi_IntrGlobalDisable(SpiInstancePtr);
return XST_SUCCESS;
}
static int
xspi_open(struct inode *inode, struct file *filp)
{
int retval = 0;
struct xspi_instance *dev;
func_enter();
dev = container_of(inode->i_cdev, struct xspi_instance, cdev);
filp->private_data = dev; /* for other methods */
if (dev == NULL)
return -ENODEV;
if (down_interruptible(&dev->sem))
return -EINTR;
while (dev->use_count++ == 0) {
/*
* This was the first opener; we need to get the IRQ,
* and to setup the device as master.
*/
retval = request_irq(dev->irq, xspi_isr, 0, XSPI_NAME,
&dev->Spi);
if (retval != 0) {
printk(KERN_ERR XSPI_NAME
"%d: Could not allocate interrupt %d.\n",
dev->device_id, dev->irq);
break;
}
if (XSpi_SetOptions(&dev->Spi, XSPI_DEFAULT_OPTIONS) !=
XST_SUCCESS) {
printk(KERN_ERR XSPI_NAME
"%d: Could not set device options.\n",
dev->device_id);
free_irq(dev->irq, &dev->Spi);
retval = -EIO;
break;
}
if (XSpi_Start(&dev->Spi) != XST_SUCCESS) {
printk(KERN_ERR XSPI_NAME
"%d: Could not start the device.\n",
dev->device_id);
free_irq(dev->irq, &dev->Spi);
retval = -EIO;
break;
}
break;
}
if (retval != 0)
--dev->use_count;
up(&dev->sem);
return retval;
}
/*****
* PmodCtlSys_init() - initialize the PmodCtlsys
*
* This function initializes the PmodCtlSys ADC (an MSP3202). Sine
* the MSP3202 is a SPI device the primary purpose of the function
* is to configure and start the Xilinx SPI peripheral. It checks
* basic functionality of the SPI peripheral by running the self-test.
* It also writes the correct data to the global send buffer PmodCtlSys_SndBuf[]
* because its contents never change. This code is based on the Xilinx SPI
* driver "spi_polled_example.c" example included in the EDK.
*****/
XStatus PmodCtlSys_init(XSpi *SpiInstancePtr, u16 SpiDeviceID)
{
XStatus Status; // return status from SPI driver functions
XSpi_Config *ConfigPtr; // Pointer to Configuration data
// Initialize the SPI driver so that it is ready to use.
ConfigPtr = XSpi_LookupConfig(SpiDeviceID);
if (ConfigPtr == NULL)
{
return XST_DEVICE_NOT_FOUND;
}
Status = XSpi_CfgInitialize(SpiInstancePtr, ConfigPtr,
ConfigPtr->BaseAddress);
if (Status != XST_SUCCESS)
{
return XST_FAILURE;
}
// Perform a self-test to ensure that the hardware was built correctly
Status = XSpi_SelfTest(SpiInstancePtr);
if (Status != XST_SUCCESS)
{
return XST_FAILURE;
}
// Set the Spi device as a master,
// SS goes low for entire transaction (does not toggle every 8 bits)
// All other bits are OK as defaults
Status = XSpi_SetOptions(SpiInstancePtr, XSP_MASTER_OPTION | XSP_MANUAL_SSELECT_OPTION);
if (Status != XST_SUCCESS)
{
return XST_FAILURE;
}
// Start the SPI driver so that the device is enabled
// and then disable the Global interrupt because we
// are using the peripheral in polled mode
XSpi_Start(SpiInstancePtr);
XSpi_IntrGlobalDisable(SpiInstancePtr);
// initialize the SPI send buffer. Since the PmodCtlSys only
// uses the channel 0 ADC in the MPS3202 the send buffer
// contents will always be the same.
// Command Byte 1 - Start bit is in the LSB, others are don't care
// Command Byte 2 - single-ended input, Select Channel 0, send data most-significant bit first
// Command Byte 2 - needed to have ADC return all the counts bits. All bits are don't care
PmodCtlSys_SndBuf[0] = MSP3202_START_MSK;
PmodCtlSys_SndBuf[1] = (MSP3202_SGL_MSK << 7) | (MSP3202_SEL_CHNL0_MSK << 6) | (MSP3202_SEL_MSBF_MSK << 5);
PmodCtlSys_SndBuf[2] = 0x55;
return XST_SUCCESS;
}
/***************************************************************************//**
* @brief spi_init
*******************************************************************************/
int32_t spi_init(uint32_t device_id,
uint8_t clk_pha,
uint8_t clk_pol)
{
uint32_t base_addr = 0;
uint32_t spi_options = 0;
#ifdef _XPARAMETERS_PS_H_
spi_config = XSpiPs_LookupConfig(device_id);
base_addr = spi_config->BaseAddress;
XSpiPs_CfgInitialize(&spi_instance, spi_config, base_addr);
spi_options = XSPIPS_MASTER_OPTION |
(clk_pol ? XSPIPS_CLK_ACTIVE_LOW_OPTION : 0) |
(clk_pha ? XSPIPS_CLK_PHASE_1_OPTION : 0) |
(spi_decoded_cs ? XSPIPS_DECODE_SSELECT_OPTION : 0) |
XSPIPS_FORCE_SSELECT_OPTION;
XSpiPs_SetOptions(&spi_instance, spi_options);
XSpiPs_SetClkPrescaler(&spi_instance, XSPIPS_CLK_PRESCALE_32);
/* FIXME: Temporary 15.2 Fix */
XSpiPs_CfgInitialize(&spi_instance, spi_config, base_addr);
XSpiPs_SetOptions(&spi_instance, spi_options);
XSpiPs_SetClkPrescaler(&spi_instance, XSPIPS_CLK_PRESCALE_32);
#else
XSpi_Initialize(&spi_instance, device_id);
XSpi_Stop(&spi_instance);
spi_config = XSpi_LookupConfig(device_id);
base_addr = spi_config->BaseAddress;
XSpi_CfgInitialize(&spi_instance, spi_config, base_addr);
spi_options = XSP_MASTER_OPTION |
(clk_pol ? XSP_CLK_ACTIVE_LOW_OPTION : 0) |
(clk_pha ? XSP_CLK_PHASE_1_OPTION : 0) |
XSP_MANUAL_SSELECT_OPTION;
XSpi_SetOptions(&spi_instance, spi_options);
XSpi_Start(&spi_instance);
XSpi_IntrGlobalDisable(&spi_instance);
#endif
return 0;
}
/***************************************************************************//**
* @brief spi_init
*******************************************************************************/
int32_t spi_init(uint32_t device_id,
uint8_t clk_pha,
uint8_t clk_pol)
{
uint32_t base_addr = 0;
uint32_t control_val = 0;
#ifdef _XPARAMETERS_PS_H_
uint8_t byte = 0;
spi_config = XSpiPs_LookupConfig(device_id);
base_addr = spi_config->BaseAddress;
XSpiPs_CfgInitialize(&spi_instance, spi_config, base_addr);
control_val = XSPIPS_CR_SSFORCE_MASK |
XSPIPS_CR_SSCTRL_MASK |
4 << XSPIPS_CR_PRESC_SHIFT |
(clk_pha ? XSPIPS_CR_CPHA_MASK : 0) |
(clk_pol ? XSPIPS_CR_CPOL_MASK : 0) |
XSPIPS_CR_MSTREN_MASK;
XSpiPs_WriteReg(base_addr, XSPIPS_CR_OFFSET, control_val);
for(byte = 0; byte < 128; byte++)
{
XSpiPs_ReadReg(base_addr, XSPIPS_RXD_OFFSET);
}
#else
XSpi_Initialize(&spi_instance, device_id);
XSpi_Stop(&spi_instance);
spi_config = XSpi_LookupConfig(device_id);
base_addr = spi_config->BaseAddress;
XSpi_CfgInitialize(&spi_instance, spi_config, base_addr);
control_val = XSP_MASTER_OPTION |
XSP_CLK_PHASE_1_OPTION |
XSP_MANUAL_SSELECT_OPTION;
XSpi_SetOptions(&spi_instance, control_val);
XSpi_Start(&spi_instance);
XSpi_IntrGlobalDisable(&spi_instance);
XSpi_SetSlaveSelect(&spi_instance, 1);
#endif
return SUCCESS;
}
int ACL_SPIInit(XSpi *SpiInstancePtr){
int Status;
XSpi_Config *ConfigPtr; /* Pointer to Configuration data */
/*
* Initialize the SPI driver so that it is ready to use.
*/
ConfigPtr = &XSpi_ACLConfig;
if (ConfigPtr == NULL) {
return XST_DEVICE_NOT_FOUND;
}
Status = XSpi_CfgInitialize(SpiInstancePtr, ConfigPtr, ConfigPtr->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
Status = XSpi_SetOptions(SpiInstancePtr, (XSP_MASTER_OPTION | XSP_CLK_ACTIVE_LOW_OPTION | XSP_CLK_PHASE_1_OPTION) | XSP_MANUAL_SSELECT_OPTION); //Manual SS off
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
Status = XSpi_SetSlaveSelect(SpiInstancePtr, 1);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Start the SPI driver so that the device is enabled.
*/
XSpi_Start(SpiInstancePtr);
/*
* Disable Global interrupt to use polled mode operation
*/
XSpi_IntrGlobalDisable(SpiInstancePtr);
return XST_SUCCESS;
}
void OledHostInit()
{
XSpi_Config *SPIConfigPtr;
XGpio_Config *GPIOConfigPtr;
int status;
/*
* Initialize the SPI driver so that it is ready to use.
*/
SPIConfigPtr = XSpi_LookupConfig(XPAR_SPI_1_DEVICE_ID);
if (SPIConfigPtr == NULL)
{
printf("OledHostInit: ERROR: SPI device not found");
}
status = XSpi_CfgInitialize(&SpiInstance, SPIConfigPtr, SPIConfigPtr->BaseAddress);
if (status != XST_SUCCESS)
{
printf("OledHostInit: ERROR: cannot init SPI");
}
/*
* Set the Spi device as a master.
*/
status = XSpi_SetOptions( &SpiInstance, XSP_MASTER_OPTION | XSP_MANUAL_SSELECT_OPTION |
XSP_CLK_ACTIVE_LOW_OPTION | XSP_CLK_PHASE_1_OPTION);
if (status != XST_SUCCESS)
{
printf("OledHostInit: ERROR: set SPI options");
}
/*
* Start the SPI driver so that the device is enabled.
*/
XSpi_Start(&SpiInstance);
/*
* Disable Global interrupt to use polled mode operation
*/
XSpi_IntrGlobalDisable(&SpiInstance);
u32 slaveReg = XSpi_GetSlaveSelectReg(&SpiInstance);
XSpi_SetSlaveSelectReg(&SpiInstance, 0x00);
slaveReg = XSpi_GetSlaveSelectReg(&SpiInstance);
//GPIO config
GPIOConfigPtr = XGpio_LookupConfig(XPAR_GPIO_0_DEVICE_ID);
if (GPIOConfigPtr == NULL)
{
printf("OledHostInit: ERROR: GPIO device not found");
}
status = XGpio_CfgInitialize(&gpioInstance, GPIOConfigPtr, GPIOConfigPtr->BaseAddress);
if (status != XST_SUCCESS)
{
printf("OledHostInit: ERROR: cannot init GPIO");
}
XGpio_SetDataDirection(&gpioInstance, 1, 0xf0);
XGpio_DiscreteWrite(&gpioInstance, 1, 0x0F);
}
int Mrf24j::initDrivers(void)
{
// TODO: check pin direction
/*pinMode(_pin_reset, OUTPUT);
pinMode(_pin_cs, OUTPUT);
pinMode(_pin_int, INPUT);*/
XSpi_Config *SPIConfigPtr;
XGpio_Config *GPIOConfigPtr;
int status;
/*
* Initialize the SPI driver so that it is ready to use.
*/
SPIConfigPtr = XSpi_LookupConfig(XPAR_SPI_0_DEVICE_ID);
if (SPIConfigPtr == NULL)
{
return XST_DEVICE_NOT_FOUND;
}
status = XSpi_CfgInitialize(&MSpiInstance, SPIConfigPtr, SPIConfigPtr->BaseAddress);
if (status != XST_SUCCESS)
{
return XST_FAILURE;
}
/*
* Set the Spi device as a master.
*/
status = XSpi_SetOptions( &MSpiInstance, XSP_MASTER_OPTION | XSP_MANUAL_SSELECT_OPTION ); //TO DO, add msb first config
if (status != XST_SUCCESS)
{
return XST_FAILURE;
}
/*
* Start the SPI driver so that the device is enabled.
*/
XSpi_Start(&MSpiInstance);
/*
* Disable Global interrupt to use polled mode operation
*/
XSpi_IntrGlobalDisable(&MSpiInstance);
//GPIO config
GPIOConfigPtr = XGpio_LookupConfig(XPAR_GPIO_1_DEVICE_ID);
status = XGpio_CfgInitialize(&gpioInstance, GPIOConfigPtr, GPIOConfigPtr->BaseAddress);
if (status != XST_SUCCESS)
{
return XST_FAILURE;
}
XGpio_SetDataDirection(&gpioInstance, 1, 0x1); //check data direction
XGpio_DiscreteWrite(&gpioInstance, 1, 0x6); //check register, check wake pin if it is ok high
//for(int i = 0; i < 20; i++)
//{
//u32 intr = XGpio_InterruptGetEnabled(&gpioInstance);
//u32 sts = XGpio_InterruptGetStatus(&gpioInstance);
//XGpio_InterruptClear(&gpioInstance, XGPIO_IR_CH1_MASK);
///sts = XGpio_InterruptGetStatus(&gpioInstance);
//u32 usts = sts;
//}
/*SPI.setBitOrder(MSBFIRST) ;
SPI.setDataMode(SPI_MODE0);
SPI.begin();*/
return XST_SUCCESS;
}
/**
*
* Main function to execute the Numonyx Quad Serial Flash Read/Write example.
*
* @param None
*
* @return XST_SUCCESS if successful else XST_FAILURE.
*
* @note None
*
******************************************************************************/
int main()
{
int Status;
u32 Index;
u32 Address;
XIsf_WriteParam WriteParam;
XIsf_ReadParam ReadParam;
/*
* Initialize the SPI driver so that it's ready to use,
* specify the device ID that is generated in xparameters.h.
*/
Status = XSpi_Initialize(&Spi, SPI_DEVICE_ID);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Connect the SPI driver to the interrupt subsystem such that
* interrupts can occur. This function is application specific.
*/
Status = SetupInterruptSystem(&Spi);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup the handler for the SPI that will be called from the interrupt
* context when an SPI status occurs, specify a pointer to the SPI
* driver instance as the callback reference so the handler is able to
* access the instance data.
*/
XIsf_SetStatusHandler(&Isf, &Spi, (XSpi_StatusHandler)SpiHandler);
/*
* Start the SPI driver so that interrupts and the device are enabled.
*/
XSpi_Start(&Spi);
/*
* Set the QSPI options
*/
Status = XIsf_SetSpiConfiguration(&Isf, &Spi,
XSP_MASTER_OPTION | XSP_MANUAL_SSELECT_OPTION,
XISF_SPI_PRESCALER);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Initialize the Serial Flash Library.
*/
Status = XIsf_Initialize(&Isf, &Spi, ISF_SPI_SELECT, IsfWriteBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set The transfer Mode to Interrupt
*/
XIsf_SetTransferMode(&Isf,XISF_INTERRUPT_MODE);
/*
* Specify the address in the Serial Flash for the Erase/Write/Read
* operations.
*/
Address = ISF_TEST_ADDRESS;
/*
* The following code Erases a Sector in the Numonyx Serial Flash.
*/
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Sector Erase operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Erase(&Isf, XISF_SECTOR_ERASE, Address);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set the
* - Address within the Serial Flash where the data is to be written.
* - Number of bytes to be written to the Serial Flash.
* - Write Buffer which contains the data to be written to the Serial
* Flash.
*/
WriteParam.Address = Address;
WriteParam.NumBytes = ISF_PAGE_SIZE;
WriteParam.WritePtr = WriteBuffer;
/*
* Prepare the write buffer. Fill in the data need to be written into
* Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
WriteParam.WritePtr[Index] = Index + ISF_TEST_BYTE;
}
/*
* Perform the Write operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Write(&Isf, XISF_DUAL_IP_PAGE_WRITE, (void*) &WriteParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read from the flash using Dual Output Fast Read command.
* Set the
* - Address in the Serial Flash where the data is to be read from.
* - Number of bytes to be read from the Serial Flash.
* - Read Buffer to which the data is to be read.
* - Number of dummy bytes for the read command.
*/
ReadParam.Address = Address;
ReadParam.NumBytes = ISF_PAGE_SIZE;
ReadParam.ReadPtr = ReadBuffer;
ReadParam.NumDummyBytes = DUAL_READ_DUMMY_BYTES;
/*
* Clear the read Buffer.
*/
for(Index = 0; Index < ISF_PAGE_SIZE + XISF_CMD_SEND_EXTRA_BYTES +
DUAL_READ_DUMMY_BYTES; Index++) {
ReadBuffer[Index] = 0x0;
}
/*
* Perform the read operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Read(&Isf, XISF_DUAL_OP_FAST_READ, (void*) &ReadParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Compare the data read against the data Written.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
if(ReadBuffer[Index + XISF_CMD_SEND_EXTRA_BYTES +
DUAL_READ_DUMMY_BYTES] !=
(u8)(Index + ISF_TEST_BYTE)) {
return XST_FAILURE;
}
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Move to the next page in the flash.
*/
Address += ISF_PAGE_SIZE;
/*
* Set the
* - Address within the Serial Flash where the data is to be written.
* - Number of bytes to be written to the Serial Flash.
* - Write Buffer which contains the data to be written to the Serial
* Flash.
*/
WriteParam.Address = Address;
WriteParam.NumBytes = ISF_PAGE_SIZE;
WriteParam.WritePtr = WriteBuffer;
/*
* Prepare the write buffer. Fill in the data need to be written into
* Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
WriteParam.WritePtr[Index] = Index + ISF_TEST_BYTE;
}
/*
* Perform the Write operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Write(&Isf, XISF_DUAL_IP_EXT_PAGE_WRITE, (void*) &WriteParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read from the flash using Dual Input/Output Fast Read command.
* Set the
* - Address in the Serial Flash where the data is to be read from.
* - Number of bytes to be read from the Serial Flash.
* - Read Buffer to which the data is to be read.
* - Number of dummy bytes for the read command.
*/
ReadParam.Address = Address;
ReadParam.NumBytes = ISF_PAGE_SIZE;
ReadParam.ReadPtr = ReadBuffer;
ReadParam.NumDummyBytes = DUAL_IO_READ_DUMMY_BYTES;
/*
* Clear the read Buffer.
*/
for(Index = 0; Index < ISF_PAGE_SIZE + XISF_CMD_SEND_EXTRA_BYTES +
DUAL_IO_READ_DUMMY_BYTES; Index++) {
ReadBuffer[Index] = 0x0;
}
/*
* Perform the read operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Read(&Isf, XISF_DUAL_IO_FAST_READ, (void*) &ReadParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Compare the data read against the data Written.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
if(ReadBuffer[Index + XISF_CMD_SEND_EXTRA_BYTES +
DUAL_IO_READ_DUMMY_BYTES] !=
(u8)(Index + ISF_TEST_BYTE)) {
return XST_FAILURE;
}
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Move to the next page in the flash.
*/
Address += ISF_PAGE_SIZE;
/*
* Set the
* - Address within the Serial Flash where the data is to be written.
* - Number of bytes to be written to the Serial Flash.
* - Write Buffer which contains the data to be written to the Serial
* Flash.
*/
WriteParam.Address = Address;
WriteParam.NumBytes = ISF_PAGE_SIZE;
WriteParam.WritePtr = WriteBuffer;
/*
* Prepare the write buffer. Fill in the data need to be written into
* Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
WriteParam.WritePtr[Index] = Index + ISF_TEST_BYTE;
}
/*
* Perform the Write operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Write(&Isf, XISF_QUAD_IP_PAGE_WRITE, (void*) &WriteParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read from the flash using Quad Output Fast Read command.
* Set the
* - Address in the Serial Flash where the data is to be read from.
* - Number of bytes to be read from the Serial Flash.
* - Read Buffer to which the data is to be read.
* - Number of dummy bytes for the read command.
*/
ReadParam.Address = Address;
ReadParam.NumBytes = ISF_PAGE_SIZE;
ReadParam.ReadPtr = ReadBuffer;
ReadParam.NumDummyBytes = QUAD_READ_DUMMY_BYTES;
/*
* Clear the read Buffer.
*/
for(Index = 0; Index < ISF_PAGE_SIZE + XISF_CMD_SEND_EXTRA_BYTES +
QUAD_READ_DUMMY_BYTES; Index++) {
ReadBuffer[Index] = 0x0;
}
/*
* Perform the read operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Read(&Isf, XISF_QUAD_OP_FAST_READ, (void*) &ReadParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Compare the data read against the data Written.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
if(ReadBuffer[Index + XISF_CMD_SEND_EXTRA_BYTES +
QUAD_READ_DUMMY_BYTES] !=
(u8)(Index + ISF_TEST_BYTE)) {
return XST_FAILURE;
}
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Move to the next page in the flash.
*/
Address += ISF_PAGE_SIZE;
/*
* Set the
* - Address within the Serial Flash where the data is to be written.
* - Number of bytes to be written to the Serial Flash.
* - Write Buffer which contains the data to be written to the Serial
* Flash.
*/
WriteParam.Address = Address;
WriteParam.NumBytes = ISF_PAGE_SIZE;
WriteParam.WritePtr = WriteBuffer;
/*
* Prepare the write buffer. Fill in the data need to be written into
* Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
WriteParam.WritePtr[Index] = Index + ISF_TEST_BYTE;
}
/*
* Perform the Write operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Write(&Isf, XISF_QUAD_IP_EXT_PAGE_WRITE,
(void*) &WriteParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read from the flash using Quad Input/Output Fast Read command.
* Set the
* - Address in the Serial Flash where the data is to be read from.
* - Number of bytes to be read from the Serial Flash.
* - Read Buffer to which the data is to be read.
* - Number of dummy bytes for the read command.
*/
ReadParam.Address = Address;
ReadParam.NumBytes = ISF_PAGE_SIZE;
ReadParam.ReadPtr = ReadBuffer;
ReadParam.NumDummyBytes = QUAD_IO_READ_DUMMY_BYTES;
/*
* Clear the read Buffer.
*/
for(Index = 0; Index < ISF_PAGE_SIZE + XISF_CMD_SEND_EXTRA_BYTES +
QUAD_IO_READ_DUMMY_BYTES; Index++) {
ReadBuffer[Index] = 0x0;
}
/*
* Perform the read operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Read(&Isf, XISF_QUAD_IO_FAST_READ, (void*) &ReadParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Compare the data read against the data written.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
if(ReadBuffer[Index + XISF_CMD_SEND_EXTRA_BYTES +
QUAD_IO_READ_DUMMY_BYTES] !=
(u8)(Index + ISF_TEST_BYTE)) {
return XST_FAILURE;
}
}
return XST_SUCCESS;
}
/**
*
* This function does a minimal test on the Spi device and driver as a
* design example. The purpose of this function is to illustrate how to use
* the XSpi component using the polled mode.
*
* This function sends data and expects to receive the same data.
*
*
* @param SpiInstancePtr is a pointer to the instance of Spi component.
* @param SpiDeviceId is the Device ID of the Spi Device and is the
* XPAR_<SPI_instance>_DEVICE_ID value from xparameters.h.
*
* @return XST_SUCCESS if successful, otherwise XST_FAILURE.
*
* @note
*
* This function contains an infinite loop such that if the Spi device is not
* working it may never return.
*
******************************************************************************/
int SpiPolledExample(XSpi *SpiInstancePtr, u16 SpiDeviceId)
{
int Status;
u32 Count;
XSpi_Config *ConfigPtr; /* Pointer to Configuration data */
/*
* Initialize the SPI driver so that it is ready to use.
*/
ConfigPtr = XSpi_LookupConfig(SpiDeviceId);
if (ConfigPtr == NULL) {
return XST_DEVICE_NOT_FOUND;
}
Status = XSpi_CfgInitialize(SpiInstancePtr, ConfigPtr,
ConfigPtr->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform a self-test to ensure that the hardware was built correctly.
*/
Status = XSpi_SelfTest(SpiInstancePtr);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Run loopback test only in case of standard SPI mode.
*/
if (SpiInstancePtr->SpiMode != XSP_STANDARD_MODE) {
return XST_SUCCESS;
}
/*
* Set the Spi device as a master and in loopback mode.
*/
Status = XSpi_SetOptions(SpiInstancePtr, XSP_MASTER_OPTION | XSP_MANUAL_SSELECT_OPTION);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Start the SPI driver so that the device is enabled.
*/
XSpi_Start(SpiInstancePtr);
/*
* Disable Global interrupt to use polled mode operation
*/
XSpi_IntrGlobalDisable(SpiInstancePtr);
/*
* Initialize the write buffer with pattern to write, initialize the
* read buffer to zero so it can be verified after the read, the
* Test value that is added to the unique value allows the value to be
* changed in a debug environment.
*/
/*
* Transmit the data.
*/
/*Init ADCL*/
SpiInstancePtr->SlaveSelectReg = 0x00000000;
ADXL362_Init(SpiInstancePtr);
DelayMs(1);
while(1)
{
int x = 0, y=0, z=0, temp;
x= ADXL362_ReadX(SpiInstancePtr);
y= ADXL362_ReadY(SpiInstancePtr);
z= ADXL362_ReadZ(SpiInstancePtr);
temp = ADXL362_ReadTemp(SpiInstancePtr);
DelayMs(5);
xil_printf("X: %d\r\n", x);
xil_printf("Y: %d\r\n", y);
xil_printf("Z: %d\r\n", z);
xil_printf("temperature: %d\r\n", temp);
}
SpiInstancePtr->SlaveSelectReg = 0x0000001;
return XST_SUCCESS;
}
/**
*
* Main function to execute the Intel Serial Flash SPR example.
*
* @param None
*
* @return XST_SUCCESS if successful else XST_FAILURE.
*
* @note None
*
******************************************************************************/
int main()
{
int Status;
u32 Index;
u32 Address;
u8 StatusReg;
XIsf_WriteParam WriteParam;
XIsf_ReadParam ReadParam;
/*
* Initialize the SPI driver so that it's ready to use,
* specify the device ID that is generated in xparameters.h.
*/
Status = XSpi_Initialize(&Spi, SPI_DEVICE_ID);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Connect the SPI driver to the interrupt subsystem such that
* interrupts can occur. This function is application specific.
*/
Status = SetupInterruptSystem(&Spi);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup the handler for the SPI that will be called from the interrupt
* context when an SPI status occurs, specify a pointer to the SPI
* driver instance as the callback reference so the handler is able to
* access the instance data.
*/
XIsf_SetStatusHandler(&Isf, &Spi, (XSpi_StatusHandler)SpiHandler);
/*
* Start the SPI driver so that interrupts and the device are enabled.
*/
XSpi_Start(&Spi);
/*
* Initialize the Serial Flash Library.
*/
Status = XIsf_Initialize(&Isf, &Spi, ISF_SPI_SELECT, IsfWriteBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set The transfer Mode to Interrupt
*/
XIsf_SetTransferMode(&Isf,XISF_INTERRUPT_MODE);
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read the sector protection register.
*/
TransferInProgress = TRUE;
Status = XIsf_SectorProtect(&Isf, XISF_SPR_READ, ReadBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Clear all the block protection bits in the sector protection register
* value read above.
*/
WriteBuffer[BYTE1] = ReadBuffer[BYTE2] &
(~(XISF_SR_BLOCK_PROTECT_MASK));
/*
* Write this value to the sector protection register to disable the
* sector protection.
*/
TransferInProgress = TRUE;
Status = XIsf_SectorProtect(&Isf, XISF_SPR_WRITE, WriteBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Specify the address in the Serial Flash for the Erase/Write/Read
* operations.
*/
Address = ISF_TEST_ADDRESS;
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Sector Erase operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Erase(&Isf, XISF_SECTOR_ERASE, Address);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* - Set the address within the Serial Flash where the data is to be
* written.
* - Set the number of bytes to be written to the Serial Flash.
* - Write Buffer which contains the data to be written to the Serial
* Flash.
*/
WriteParam.Address = Address;
WriteParam.NumBytes = ISF_PAGE_SIZE;
WriteParam.WritePtr = WriteBuffer;
/*
* Prepare the write buffer. Fill in the data need to be written into
* Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
WriteParam.WritePtr[Index] = Index + ISF_TEST_BYTE;
}
/*
* Perform the Write operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Write(&Isf, XISF_WRITE, (void*) &WriteParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read the sector protection register.
*/
TransferInProgress = TRUE;
Status = XIsf_SectorProtect(&Isf, XISF_SPR_READ, ReadBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Set all the block protection bits in the sector protection register
* value read above and write it back to the sector protection register.
*/
WriteBuffer[BYTE1] = ReadBuffer[BYTE2] |
(XISF_SR_BLOCK_PROTECT_MASK);
/*
* Enable the sector protection.
*/
TransferInProgress = TRUE;
Status = XIsf_SectorProtect(&Isf, XISF_SPR_WRITE, WriteBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Sector Erase operation. This should not work as writes to
* the Serial Flash are disabled.
*/
TransferInProgress = TRUE;
Status = XIsf_Erase(&Isf, XISF_SECTOR_ERASE, Address);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read the Status Register.
*/
TransferInProgress = TRUE;
Status = XIsf_GetStatus(&Isf, ReadBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is in progress.
*/
while(TransferInProgress);
/*
* Check if there are any errors in the transaction.
*/
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Check if the erase fail flag is set in the status register. This flag
* should be set as a sector erase operation was attempted when sector
* protection was enabled.
*/
StatusReg = ReadBuffer[BYTE2];
if((StatusReg & XISF_SR_ERASE_FAIL_MASK) == 0) {
return XST_FAILURE;
}
/*
* Clear the status register fail flags in the Serial Flash status
* register.
*/
TransferInProgress = TRUE;
Status = XIsf_Ioctl(&Isf, XISF_IOCTL_CLEAR_SR_FAIL_FLAGS);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read the Status Register.
*/
TransferInProgress = TRUE;
Status = XIsf_GetStatus(&Isf, ReadBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is in progress.
*/
while(TransferInProgress);
/*
* Check if there are any errors in the transaction.
*/
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Check if the erase fail flag is clear in the status register. This
* flag should be clear as a 'Clear SR Fail Flags' command has been
* executed.
*/
StatusReg = ReadBuffer[BYTE2];
if((StatusReg & XISF_SR_ERASE_FAIL_MASK) != 0) {
return XST_FAILURE;
}
/*
* Read the sector protection register.
*/
TransferInProgress = TRUE;
Status = XIsf_SectorProtect(&Isf, XISF_SPR_READ, ReadBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Clear all the block protection bits in the sector protection register
* value read above and write it back to the sector protection register
* to disable sector protection for all sectors.
*/
WriteBuffer[BYTE1] = ReadBuffer[BYTE2] &
~(XISF_SR_BLOCK_PROTECT_MASK);
/*
* Disable the sector protection.
*/
TransferInProgress = TRUE;
Status = XIsf_SectorProtect(&Isf, XISF_SPR_WRITE, WriteBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* The following code Reads data from a Page in the Intel Serial Flash.
*/
/*
* Set the
* - Address in the Serial Flash where the data is to be read from.
* - Number of bytes to be read from the Serial Flash.
* - Read Buffer to which the data is to be read.
*/
ReadParam.Address = Address;
ReadParam.NumBytes = ISF_PAGE_SIZE;
ReadParam.ReadPtr = ReadBuffer;
/*
* Perform the read operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Read(&Isf, XISF_READ, (void*) &ReadParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Compare the data read against the data Written.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
if(ReadBuffer[Index + XISF_CMD_SEND_EXTRA_BYTES] !=
(u8)(Index + ISF_TEST_BYTE)) {
return XST_FAILURE;
}
}
return XST_SUCCESS;
}
/**
*
* This function does a minimal test on the Spi device and driver as a
* design example. The purpose of this function is to illustrate how to use
* the XSpi component using the polled mode.
*
* This function sends data and expects to receive the same data.
*
*
* @param SpiInstancePtr is a pointer to the instance of Spi component.
* @param SpiDeviceId is the Device ID of the Spi Device and is the
* XPAR_<SPI_instance>_DEVICE_ID value from xparameters.h.
*
* @return XST_SUCCESS if successful, otherwise XST_FAILURE.
*
* @note
*
* This function contains an infinite loop such that if the Spi device is not
* working it may never return.
*
******************************************************************************/
int SpiPolledExample(XSpi *SpiInstancePtr, u16 SpiDeviceId)
{
int Status;
u32 Count;
u8 Test;
XSpi_Config *ConfigPtr; /* Pointer to Configuration data */
/*
* Initialize the SPI driver so that it is ready to use.
*/
ConfigPtr = XSpi_LookupConfig(SpiDeviceId);
if (ConfigPtr == NULL) {
return XST_DEVICE_NOT_FOUND;
}
Status = XSpi_CfgInitialize(SpiInstancePtr, ConfigPtr,
ConfigPtr->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform a self-test to ensure that the hardware was built correctly.
*/
Status = XSpi_SelfTest(SpiInstancePtr);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Run loopback test only in case of standard SPI mode.
*/
if (SpiInstancePtr->SpiMode != XSP_STANDARD_MODE) {
return XST_SUCCESS;
}
/*
* Set the Spi device as a master and in loopback mode.
*/
Status = XSpi_SetOptions(SpiInstancePtr, XSP_MASTER_OPTION |
XSP_LOOPBACK_OPTION);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Start the SPI driver so that the device is enabled.
*/
XSpi_Start(SpiInstancePtr);
/*
* Disable Global interrupt to use polled mode operation
*/
XSpi_IntrGlobalDisable(SpiInstancePtr);
/*
* Initialize the write buffer with pattern to write, initialize the
* read buffer to zero so it can be verified after the read, the
* Test value that is added to the unique value allows the value to be
* changed in a debug environment.
*/
Test = 0x10;
for (Count = 0; Count < BUFFER_SIZE; Count++) {
WriteBuffer[Count] = (u8)(Count + Test);
ReadBuffer[Count] = 0;
}
/*
* Transmit the data.
*/
XSpi_Transfer(SpiInstancePtr, WriteBuffer, ReadBuffer, BUFFER_SIZE);
/*
* Compare the data received with the data that was transmitted.
*/
for (Count = 0; Count < BUFFER_SIZE; Count++) {
if (WriteBuffer[Count] != ReadBuffer[Count]) {
return XST_FAILURE;
}
}
return XST_SUCCESS;
}
/**
*
* This function does a minimal test on the Spi device and driver as a
* design example. The purpose of this function is to illustrate how to use
* the XSpi component using the interrupt mode.
*
* This function sends data and expects to receive the same data.
*
*
* @param IntcInstancePtr is a pointer to the instance of the INTC
* component.
* @param SpiInstancePtr is a pointer to the instance of Spi component.
* @param SpiDeviceId is the Device ID of the Spi Device and is the
* XPAR_<SPI_instance>_DEVICE_ID value from xparameters.h.
* @param SpiIntrId is the interrupt Id and is typically
* XPAR_<INTC_instance>_<SPI_instance>_VEC_ID value from
* xparameters.h .
*
* @return XST_SUCCESS if successful, otherwise XST_FAILURE.
*
* @note
*
* This function contains an infinite loop such that if interrupts are not
* working it may never return.
*
******************************************************************************/
int SpiIntrExample(XIntc *IntcInstancePtr, XSpi *SpiInstancePtr,
u16 SpiDeviceId, u16 SpiIntrId)
{
int Status;
u32 Count;
u8 Test;
XSpi_Config *ConfigPtr; /* Pointer to Configuration data */
/*
* Initialize the SPI driver so that it is ready to use.
*/
ConfigPtr = XSpi_LookupConfig(SpiDeviceId);
if (ConfigPtr == NULL) {
return XST_DEVICE_NOT_FOUND;
}
Status = XSpi_CfgInitialize(SpiInstancePtr, ConfigPtr,
ConfigPtr->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform a self-test to ensure that the hardware was built correctly.
*/
Status = XSpi_SelfTest(SpiInstancePtr);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Run loopback test only in case of standard SPI mode.
*/
if (SpiInstancePtr->SpiMode != XSP_STANDARD_MODE) {
return XST_SUCCESS;
}
/*
* Connect the Spi device to the interrupt subsystem such that
* interrupts can occur. This function is application specific.
*/
Status = SpiSetupIntrSystem(IntcInstancePtr,
SpiInstancePtr,
SpiIntrId);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup the handler for the SPI that will be called from the interrupt
* context when an SPI status occurs, specify a pointer to the SPI
* driver instance as the callback reference so the handler is able to
* access the instance data.
*/
XSpi_SetStatusHandler(SpiInstancePtr, SpiInstancePtr,
(XSpi_StatusHandler) SpiIntrHandler);
/*
* Set the Spi device as a master and in loopback mode.
*/
Status = XSpi_SetOptions(SpiInstancePtr, XSP_MASTER_OPTION |
XSP_LOOPBACK_OPTION);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Start the SPI driver so that interrupts and the device are enabled.
*/
XSpi_Start(SpiInstancePtr);
/*
* Initialize the write buffer with pattern to write, initialize the
* read buffer to zero so it can be verified after the read, the
* Test value that is added to the unique value allows the value to be
* changed in a debug environment.
*/
Test = 0x10;
for (Count = 0; Count < BUFFER_SIZE; Count++) {
WriteBuffer[Count] = (u8)(Count + Test);
ReadBuffer[Count] = 0;
}
/*
* Transmit the data.
*/
TransferInProgress = TRUE;
XSpi_Transfer(SpiInstancePtr, WriteBuffer, ReadBuffer, BUFFER_SIZE);
/*
* Wait for the transmission to be complete.
*/
while (TransferInProgress);
/*
* Disable the Spi interrupt.
*/
SpiDisableIntrSystem(IntcInstancePtr, SpiIntrId);
/*
* Compare the data received with the data that was transmitted.
*/
for (Count = 0; Count < BUFFER_SIZE; Count++) {
if (WriteBuffer[Count] != ReadBuffer[Count]) {
return XST_FAILURE;
}
}
return XST_SUCCESS;
}
/**
*
* Main function to execute the Atmel Serial Flash Read/Write example.
*
* @param None.
*
* @return XST_SUCCESS if successful else XST_FAILURE.
*
* @note None.
*
******************************************************************************/
int main(void)
{
int Status;
u16 Index;
XIsf_WriteParam WriteParam;
XIsf_ReadParam ReadParam;
u32 Address;
/*
* Initialize the SPI driver so that it's ready to use,
* specify the device ID that is generated in xparameters.h.
*/
Status = XSpi_Initialize(&Spi, SPI_DEVICE_ID);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Connect the SPI driver to the interrupt subsystem such that
* interrupts can occur. This function is application specific.
*/
Status = SetupInterruptSystem(&Spi);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup the handler for the SPI that will be called from the interrupt
* context when an SPI status occurs, specify a pointer to the SPI
* driver instance as the callback reference so the handler is able to
* access the instance data.
*/
XIsf_SetStatusHandler(&Isf, &Spi, (XSpi_StatusHandler)SpiHandler);
/*
* Start the SPI driver so that interrupts and the device are enabled.
*/
Status = XSpi_Start(&Spi);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Initialize the In-system and Serial Flash Library.
*/
Status = XIsf_Initialize(&Isf, &Spi, ISF_SPI_SELECT, IsfWriteBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set The transfer Mode to Interrupt
*/
XIsf_SetTransferMode(&Isf,XISF_INTERRUPT_MODE);
/*
* Specify the address in the Serial Flash for the Erase/Write/Read
* operations.
*/
Address = TEST_ADDRESS;
/*
* Perform the Page Erase operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Erase(&Isf, XISF_PAGE_ERASE, Address);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for any errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Serial Flash is ready.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set the
* - Address within the Serial Flash where the data is to be written.
* - The number of bytes to be written to the Serial Flash.
* - Write Buffer which contains the data to be written to the Serial
* Flash.
*/
WriteParam.Address = Address;
WriteParam.NumBytes = ISF_PAGE_SIZE;
WriteParam.WritePtr = WriteBuffer;
/*
* Prepare the write buffer. Fill in the data need to be written into
* Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
WriteParam.WritePtr[Index] = Index + ISF_TEST_BYTE;
}
/*
* Perform the Write operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Write(&Isf, XISF_WRITE, (void*) &WriteParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for any errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Serial Flash is ready.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set the
* - Address in the Serial Flash where the data is to be read from.
* - Number of bytes to be read from the Serial Flash.
* - Read Buffer to which the data is to be read.
*/
ReadParam.Address = Address;
ReadParam.NumBytes = ISF_PAGE_SIZE;
ReadParam.ReadPtr = ReadBuffer;
/*
* Perform the Read operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Read(&Isf, XISF_READ, (void*) &ReadParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for any errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Compare the Data Read with the Data Written to the Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
if(ReadParam.ReadPtr[Index + XISF_CMD_SEND_EXTRA_BYTES] !=
(u8)(Index + ISF_TEST_BYTE)) {
return XST_FAILURE;
}
}
return XST_SUCCESS;
}
int main() {
xil_printf("Master SPI oRSC echo test\n");
// initialize stdout.
init_platform();
tx_buffer = cbuffer_new();
rx_buffer = cbuffer_new();
spi_stream = spi_stream_init(
tx_buffer, rx_buffer,
DoSpiTransfer, // callback which triggers a SPI transfer
0);
int Status;
XSpi_Config *ConfigPtr; /* Pointer to Configuration data */
/*
* Initialize the SPI driver so that it is ready to use.
*/
ConfigPtr = XSpi_LookupConfig(SPI_DEVICE_ID);
if (ConfigPtr == NULL) {
xil_printf ("Error: could not lookup SPI configuration\n");
return XST_DEVICE_NOT_FOUND;
}
Status = XSpi_CfgInitialize(&SpiInstance, ConfigPtr,
ConfigPtr->BaseAddress);
if (Status != XST_SUCCESS) {
xil_printf("Error: could not initialize the SPI device\n");
return XST_FAILURE;
}
Status = XSpi_SelfTest(&SpiInstance);
if (Status != XST_SUCCESS) {
xil_printf("Error: The SPI self test failed.\n");
return XST_FAILURE;
}
/*
* Connect the Spi device to the interrupt subsystem such that
* interrupts can occur. This function is application specific.
*/
Status = SpiSetupIntrSystem(&IntcInstance, &SpiInstance, SPI_IRPT_INTR);
if (Status != XST_SUCCESS) {
xil_printf("Error: Could not setup interrupt system.\n");
return XST_FAILURE;
}
/*
* Set the Spi device as a master.
*/
Status = XSpi_SetOptions(&SpiInstance, XSP_MASTER_OPTION);
if (Status != XST_SUCCESS) {
xil_printf("Error: Could not set as master\n");
return XST_FAILURE;
}
// Go!
XSpi_Start(&SpiInstance);
// Note: to disable interrupt, do: XIntc_Disconnect(&IntcInstance,
// SPI_IRPT_INTR);
u32 expected_rx = 0;
u32 current_tx = 0;
while (1) {
// fill up the transmit buffer
while (cbuffer_freespace(tx_buffer)) {
cbuffer_push_back(tx_buffer, current_tx++);
}
// check to make sure the received buffer is what we expect
while (cbuffer_size(rx_buffer)) {
u32 front = cbuffer_value_at(rx_buffer, 0);
if (front != expected_rx) {
//xil_printf("Error: expected %lx, got %lx!\n", expected_rx, front);
xil_printf("Error: data value\n");
}
expected_rx++;
cbuffer_deletefront(rx_buffer, 1);
}
}
return 0;
}
DSTATUS disk_initialize (void)
{
BYTE n, cmd, ty, buf[4];
UINT tmr;
#if AXI_SPI
/*
* Initialize the SPI driver so that it's ready to use,
* specify the device ID that is generated in xparameters.h.
*/
XStatus Status = XSpi_Initialize(&Spi, XPAR_SDCARD_SPI_DEVICE_ID);
if(Status != XST_SUCCESS) {\
xil_printf("Failure INIT\r\n");
return XST_FAILURE;
}
/*
* Set the SPI device as a master and in manual slave select mode such
* that the slave select signal does not toggle for every byte of a
* transfer, this must be done before the slave select is set.
*/
Status = XSpi_SetOptions(&Spi, XSP_MASTER_OPTION |
XSP_MANUAL_SSELECT_OPTION);
if(Status != XST_SUCCESS) {
xil_printf("Failure Options\r\n");
return XST_FAILURE;
}
Status = XSpi_SetSlaveSelect(&Spi, 1);
if(Status != XST_SUCCESS) {
xil_printf("Failure Slave Select\r\n");
return XST_FAILURE;
}
XSpi_Start(&Spi);
XSpi_IntrGlobalDisable(&Spi);
DLY_US(1);
#else
INIT_PORT();
CS_H();
#endif
skip_mmc(10); /* Dummy clocks */
ty = 0;
if (send_cmd(CMD0, 0) == 1) { /* Enter Idle state */
if (send_cmd(CMD8, 0x1AA) == 1) { /* SDv2 */
for (n = 0; n < 4; n++) buf[n] = rcvr_mmc(); /* Get trailing return value of R7 resp */
if (buf[2] == 0x01 && buf[3] == 0xAA) { /* The card can work at vdd range of 2.7-3.6V */
for (tmr = 1000; tmr; tmr--) { /* Wait for leaving idle state (ACMD41 with HCS bit) */
if (send_cmd(ACMD41, 1UL << 30) == 0) break;
DLY_US(1000);
}
if (tmr && send_cmd(CMD58, 0) == 0) { /* Check CCS bit in the OCR */
for (n = 0; n < 4; n++) buf[n] = rcvr_mmc();
ty = (buf[0] & 0x40) ? CT_SD2 | CT_BLOCK : CT_SD2; /* SDv2 (HC or SC) */
}
}
} else { /* SDv1 or MMCv3 */
if (send_cmd(ACMD41, 0) <= 1) {
ty = CT_SD1; cmd = ACMD41; /* SDv1 */
} else {
ty = CT_MMC; cmd = CMD1; /* MMCv3 */
}
for (tmr = 1000; tmr; tmr--) { /* Wait for leaving idle state */
if (send_cmd(cmd, 0) == 0) break;
DLY_US(1000);
}
if (!tmr || send_cmd(CMD16, 512) != 0) /* Set R/W block length to 512 */
ty = 0;
}
}
CardType = ty;
release_spi();
return ty ? 0 : STA_NOINIT;
}
/**
*
* This function does a minimal test on the Spi device and driver as a design
* example. The purpose of this function is to illustrate the device slave
* functionality in polled mode. This function receives data from a master and
* prints the received data.
*
* @param SpiInstancePtr is a pointer to the instance of Spi component.
*
* @param SpiDeviceId is the Device ID of the Spi Device and is the
* XPAR_<SPI_instance>_DEVICE_ID value from xparameters.h.
*
* @return XST_SUCCESS if successful, otherwise XST_FAILURE.
*
* @note This function contains an infinite loop such that if the Spi
* device doesn't receive any data, it may never return.
*
******************************************************************************/
int SpiSlavePolledExample(XSpi *SpiInstancePtr, u16 SpiDeviceId)
{
XSpi_Config *ConfigPtr;
int Status;
u32 Count;
xil_printf("\r\nEntering the Spi Slave Polled Example.\r\n");
xil_printf("Waiting for data from SPI master\r\n");
/*
* Initialize the SPI driver so that it's ready to use, specify the
* device ID that is generated in xparameters.h.
*/
ConfigPtr = XSpi_LookupConfig(SpiDeviceId);
if (ConfigPtr == NULL) {
return XST_FAILURE;
}
Status = XSpi_CfgInitialize(SpiInstancePtr, ConfigPtr,
ConfigPtr->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* The SPI device is a slave by default and the clock phase and polarity
* have to be set according to its master. In this example, CPOL is set
* to active low and CPHA is set to 1.
*/
Status = XSpi_SetOptions(SpiInstancePtr, XSP_CLK_PHASE_1_OPTION |
XSP_CLK_ACTIVE_LOW_OPTION);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Start the SPI driver so that the device is enabled.
*/
XSpi_Start(SpiInstancePtr);
/*
* Disable Global interrupt to use polled mode operation.
*/
XSpi_IntrGlobalDisable(SpiInstancePtr);
/*
* Initialize the write buffer with pattern to write, initialize the
* read buffer to zero so that it can be verified after the read.
*/
Test = 0xF0;
for (Count = 0; Count < BUFFER_SIZE; Count++) {
WriteBuffer[Count] = (u8)(Count + Test);
ReadBuffer[Count] = 0;
}
/*
* Prepare the data buffers for transmission and to send/receive data
* when the SPI device is selected by a master.
*/
XSpi_Transfer(SpiInstancePtr, WriteBuffer, ReadBuffer, BUFFER_SIZE);
/*
* Print all the data received from the master so that it can be
* compared with the data sent by the master.
*/
xil_printf("\r\nReceived data is:\r\n");
for (Count = 0; Count < BUFFER_SIZE; Count++) {
xil_printf("0x%x \r\n", ReadBuffer[Count]);
}
xil_printf("\r\nExiting the Spi Slave Polled Example.\r\n");
return XST_SUCCESS;
}
/**
*
* This function does a minimal test on the Spi device and driver as a design
* example. The purpose of this function is to illustrate the device slave
* functionality in interrupt mode. This function receives data from a master and
* prints the received data.
*
* @param SpiInstancePtr is a pointer to the instance of Spi component.
* @param SpiDeviceId is the Device ID of the Spi Device and is the
* XPAR_<SPI_instance>_DEVICE_ID value from xparameters.h.
*
* @return XST_SUCCESS if successful, otherwise XST_FAILURE.
*
* @note This function contains an infinite loop such that if the Spi
* device doesn't receive any data or if the interrupts are not
* working, it may never return.
*
******************************************************************************/
static int SpiSlaveIntrExample(XSpi *SpiInstancePtr, u16 SpiDeviceId)
{
XSpi_Config *ConfigPtr;
int Status;
u32 Count;
xil_printf("\r\nEntering the Spi Slave Interrupt Example.\r\n");
xil_printf("Waiting for data from SPI master\r\n");
/*
* Initialize the SPI driver so that it's ready to use, specify the
* device ID that is generated in xparameters.h.
*/
ConfigPtr = XSpi_LookupConfig(SpiDeviceId);
if (ConfigPtr == NULL) {
return XST_FAILURE;
}
Status = XSpi_CfgInitialize(SpiInstancePtr, ConfigPtr,
ConfigPtr->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Connect the SPI driver to the interrupt subsystem such that
* interrupts can occur. This function is application specific.
*/
Status = SetupInterruptSystem(SpiInstancePtr);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup the handler for the SPI that will be called from the interrupt
* context when an SPI status occurs, specify a pointer to the SPI
* driver instance as the callback reference so the handler is able to
* access the instance data.
*/
XSpi_SetStatusHandler(SpiInstancePtr,SpiInstancePtr,(XSpi_StatusHandler)
SpiHandler);
/*
* The SPI device is a slave by default and the clock phase and polarity
* have to be set according to its master. In this example, CPOL is set
* to active low and CPHA is set to 1.
*/
Status = XSpi_SetOptions(SpiInstancePtr, XSP_CLK_PHASE_1_OPTION |
XSP_CLK_ACTIVE_LOW_OPTION);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Start the SPI driver so that the device is enabled.
*/
XSpi_Start(SpiInstancePtr);
/*
* Enable the DTR half-empty interrupt while transfering more than
* FIFO_DEPTH number of bytes in slave mode, so that the Tx FIFO
* is never empty during a transfer. If the Tx FIFO is empty during
* a transfer, it results in master receiving invalid data.
*/
XSpi_IntrEnable(SpiInstancePtr, XSP_INTR_TX_HALF_EMPTY_MASK);
/*
* Initialize the write buffer with pattern to write, initialize the
* read buffer to zero so it can be verified after the read.
*/
Test = 0x50;
for (Count = 0; Count < BUFFER_SIZE; Count++) {
WriteBuffer[Count] = (u8)(Count + Test);
ReadBuffer[Count] = 0;
}
/*
* Transmit data as a slave, when the master starts sending data.
*/
TransferInProgress = TRUE;
Status = XSpi_Transfer(SpiInstancePtr, WriteBuffer, ReadBuffer,
BUFFER_SIZE);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the transfer is complete.
*/
while (TransferInProgress == TRUE);
/*
* Print all the data received from the master.
*/
xil_printf("\r\nReceived data is:\r\n");
for (Count = 0; Count < BUFFER_SIZE; Count++) {
xil_printf("0x%x \r\n", ReadBuffer[Count]);
}
xil_printf("\r\nExiting the Spi Slave Interrupt Example.\r\n");
return XST_SUCCESS;
}
void LEDPIN_Init(void)
{
int Status;
Status = XGpio_Initialize(&dc, XPAR_AXI_GPIO_0_DEVICE_ID);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
Status = XGpio_Initialize(&reset, XPAR_AXI_GPIO_1_DEVICE_ID);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
Status = XGpio_Initialize(&led1, XPAR_AXI_GPIO_2_DEVICE_ID);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
Status = XGpio_Initialize(&led2, XPAR_AXI_GPIO_3_DEVICE_ID);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
XGpio_SetDataDirection(&dc, DC_CHANNEL, 0x0);
XGpio_DiscreteWrite(&dc, DC_CHANNEL, 0x0);
XGpio_SetDataDirection(&reset, reset_CHANNEL, 0x0);
XGpio_DiscreteWrite(&reset, reset_CHANNEL, 0x0);
XGpio_SetDataDirection(&led1, reset_CHANNEL, 0x0);
XGpio_DiscreteWrite(&led1, reset_CHANNEL, 0x0);
XGpio_SetDataDirection(&led2, reset_CHANNEL, 0x0);
XGpio_DiscreteWrite(&led2, reset_CHANNEL, 0x0);
XGpio_DiscreteWrite(&led2, reset_CHANNEL, 0x1);
XSpi_Config *ConfigPtr; /* Pointer to Configuration data */
/*
* Initialize the SPI driver so that it is ready to use.
*/
ConfigPtr = XSpi_LookupConfig(SPI_DEVICE_ID);
if (ConfigPtr == NULL) {
return XST_DEVICE_NOT_FOUND;
}
Status = XSpi_CfgInitialize(&Spi, ConfigPtr,
ConfigPtr->BaseAddress);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform a self-test to ensure that the hardware was built correctly
*/
Status = XSpi_SelfTest(&Spi);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
Status = XSpi_SetOptions(&Spi, XSP_MASTER_OPTION | XSP_CLK_ACTIVE_LOW_OPTION );//| XSP_CR_CLK_POLARITY_MASK | XSP_CR_CLK_PHASE_MASK);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
XGpio_DiscreteWrite(&led2, reset_CHANNEL, 0x0);
}
// | XSP_CR_CPOL_MASK|XSP_CR_CPHA_MASK);
//XSpiPs_SetClkPrescaler(&Spi, XSPIPS_CLK_PRESCALE_256);
XSpi_SetSlaveSelect(&Spi, 0x1);
//XSpi_Start(&Spi);
Status = XSpi_Start(&Spi);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}
XSpi_IntrGlobalDisable(&Spi);
/*Status = XSpi_SetSlaveSelect(&Spi, 0x1);
if (Status != XST_SUCCESS) {
return XST_FAILURE;
}*/
}
