/**
* acpi_suspend_enter - Actually enter a sleep state.
* @pm_state: ignored
*
* Flush caches and go to sleep. For STR we have to call arch-specific
* assembly, which in turn call acpi_enter_sleep_state().
* It's unfortunate, but it works. Please fix if you're feeling frisky.
*/
static int acpi_suspend_enter(suspend_state_t pm_state)
{
acpi_status status = AE_OK;
unsigned long flags = 0;
u32 acpi_state = acpi_target_sleep_state;
ACPI_FLUSH_CPU_CACHE();
/* Do arch specific saving of state. */
if (acpi_state == ACPI_STATE_S3) {
int error = acpi_save_state_mem();
if (error)
return error;
}
local_irq_save(flags);
acpi_enable_wakeup_device(acpi_state);
switch (acpi_state) {
case ACPI_STATE_S1:
barrier();
status = acpi_enter_sleep_state(acpi_state);
break;
case ACPI_STATE_S3:
do_suspend_lowlevel();
break;
}
/* Reprogram control registers and execute _BFS */
acpi_leave_sleep_state_prep(acpi_state);
/* ACPI 3.0 specs (P62) says that it's the responsibility
* of the OSPM to clear the status bit [ implying that the
* POWER_BUTTON event should not reach userspace ]
*/
if (ACPI_SUCCESS(status) && (acpi_state == ACPI_STATE_S3))
acpi_clear_event(ACPI_EVENT_POWER_BUTTON);
/*
* Disable and clear GPE status before interrupt is enabled. Some GPEs
* (like wakeup GPE) haven't handler, this can avoid such GPE misfire.
* acpi_leave_sleep_state will reenable specific GPEs later
*/
acpi_hw_disable_all_gpes();
local_irq_restore(flags);
printk(KERN_DEBUG "Back to C!\n");
/* restore processor state */
if (acpi_state == ACPI_STATE_S3)
acpi_restore_state_mem();
return ACPI_SUCCESS(status) ? 0 : -EFAULT;
}
static int acpi_pm_enter(suspend_state_t pm_state)
{
acpi_status status = AE_OK;
unsigned long flags = 0;
u32 acpi_state = acpi_suspend_states[pm_state];
ACPI_FLUSH_CPU_CACHE();
/* Do arch specific saving of state. */
if (pm_state > PM_SUSPEND_STANDBY) {
int error = acpi_save_state_mem();
if (error)
return error;
}
local_irq_save(flags);
acpi_enable_wakeup_device(acpi_state);
switch (pm_state) {
case PM_SUSPEND_STANDBY:
barrier();
status = acpi_enter_sleep_state(acpi_state);
break;
case PM_SUSPEND_MEM:
do_suspend_lowlevel();
break;
case PM_SUSPEND_DISK:
if (acpi_pm_ops.pm_disk_mode == PM_DISK_PLATFORM)
status = acpi_enter_sleep_state(acpi_state);
else
do_suspend_lowlevel_s4bios();
break;
case PM_SUSPEND_MAX:
acpi_power_off();
break;
default:
return -EINVAL;
}
local_irq_restore(flags);
printk(KERN_DEBUG "Back to C!\n");
/* restore processor state
* We should only be here if we're coming back from STR or STD.
* And, in the case of the latter, the memory image should have already
* been loaded from disk.
*/
if (pm_state > PM_SUSPEND_STANDBY)
acpi_restore_state_mem();
return ACPI_SUCCESS(status) ? 0 : -EFAULT;
}
/**
* acpi_system_restore_state - OS-specific restoration of state
* @state: sleep state we're exiting
*
* Note that if we're coming back from S4, the memory image should have
* already been loaded from the disk and is already in place. (Otherwise how
* else would we be here?).
*/
acpi_status
acpi_system_restore_state(
u32 state)
{
/*
* We should only be here if we're coming back from STR or STD.
* And, in the case of the latter, the memory image should have already
* been loaded from disk.
*/
if (state > ACPI_STATE_S1) {
acpi_restore_state_mem();
/* Do _early_ resume for irqs. Required by
* ACPI specs.
*/
/* TBD: call arch dependant reinitialization of the
* interrupts.
*/
#ifdef CONFIG_X86
init_8259A(0);
#endif
/* wait for power to come back */
mdelay(1000);
}
/* Be really sure that irqs are disabled. */
ACPI_DISABLE_IRQS();
/* Wait a little again, just in case... */
mdelay(1000);
/* enable interrupts once again */
ACPI_ENABLE_IRQS();
/* turn all the devices back on */
if (state > ACPI_STATE_S1)
pm_send_all(PM_RESUME, (void *)0);
return AE_OK;
}
static int acpi_pm_enter(suspend_state_t pm_state)
{
acpi_status status = AE_OK;
unsigned long flags = 0;
u32 acpi_state = acpi_suspend_states[pm_state];
ACPI_FLUSH_CPU_CACHE();
/* Do arch specific saving of state. */
if (pm_state > PM_SUSPEND_STANDBY) {
int error = acpi_save_state_mem();
if (error)
return error;
}
local_irq_save(flags);
acpi_enable_wakeup_device(acpi_state);
switch (pm_state) {
case PM_SUSPEND_STANDBY:
barrier();
status = acpi_enter_sleep_state(acpi_state);
break;
case PM_SUSPEND_MEM:
if (unlikely(acpi_simulate_suspend_to_ram)) {
printk(KERN_INFO "ACPI: simulating suspend-to-RAM: "
"not calling BIOS.\n");
} else {
do_suspend_lowlevel();
}
break;
case PM_SUSPEND_DISK:
if (acpi_pm_ops.pm_disk_mode == PM_DISK_PLATFORM)
status = acpi_enter_sleep_state(acpi_state);
break;
case PM_SUSPEND_MAX:
acpi_power_off();
break;
default:
return -EINVAL;
}
/* ACPI 3.0 specs (P62) says that it's the responsabilty
* of the OSPM to clear the status bit [ implying that the
* POWER_BUTTON event should not reach userspace ]
*/
if (ACPI_SUCCESS(status) && (acpi_state == ACPI_STATE_S3))
acpi_clear_event(ACPI_EVENT_POWER_BUTTON);
local_irq_restore(flags);
printk(KERN_DEBUG "Back to C!\n");
/* restore processor state
* We should only be here if we're coming back from STR or STD.
* And, in the case of the latter, the memory image should have already
* been loaded from disk.
*/
if (pm_state > PM_SUSPEND_STANDBY)
acpi_restore_state_mem();
return ACPI_SUCCESS(status) ? 0 : -EFAULT;
}