コード例 #1
0
/*----------------------------------------------------------------------------*/
void rtc_fun(void)
{
    MAIN_POWER_PORT_INIT();	
    MAIN_POWER_PORT_DISABLE();	
    iic_gpio_set_low();
    amp_mute(1);

    if(alm_on_flag){
		if(sys_main_vol != alrm_vol_bakup)
		sys_main_vol = alrm_vol_bakup;
    		alm_on_flag = 0;
    }
    input_number_en = 0;
    vol_change_en=0;
    key_voice_en=0;
    main_menu = MENU_RTC;
    close_alarm();
    dsp_set_eq_mode(0);			  //系统时钟div前需关闭eq
    SYSTEM_CLK_DIV4();
    key_table_sel(0);
    flush_all_msg();
    set_max_vol(MAX_ANOLOG_VOL,MAX_DIGITAL_VOL);///设置最大音量
    dac_out_select(DAC_MUSIC, 0);
	
    rtc_mode_setting = RTC_DISPLAY;
    rtc_coordinate = 0;
    alm_coordinate = 0;
    if (alm_cnt)
    {
        put_msg_lifo(MSG_ALM_ON);
    }
    else
    {
        read_rtc(&curr_time);
        chk_date_err();
        disp_port(MENU_RTC);
    }

    MAIN_POWER_PORT_INIT();	
    MAIN_POWER_PORT_DISABLE();	
	
    deal_rtc();

    amp_mute(1);
    MAIN_POWER_PORT_ENABLE();	

    delay_10ms(3);
    key_voice_en=0;
    main_vol_set(0, CHANGE_VOL_NO_MEM);
    MAIN_POWER_PORT_ENABLE();	
    amp_mute(1);
    delay_10ms(80);
  
    snooze_en =0;
	
    PT2313_Init();
    delay_10ms(10);
    PT2313_Init();
	
}
コード例 #2
0
/*----------------------------------------------------------------------------*/
void fm_radio(void)
{
//    printf("enter fm\n");
    //P05_source_select(P05_SEL_OSC1);
    amux_dsp_eq();

    sys_clk_div(2);//SYSTEM_CLK_DIV2();
    init_fm_rev();

    PT2313_Config(RADIO_CHAN,CHAN_ADJ);

    input_number_en = 1;
    vol_change_en=1;
    main_menu = MENU_FM_MAIN;
    key_table_sel(1);
    flush_all_msg();
    enter_fm_rev();
    disp_port(MENU_FM_MAIN);
    sys_clk_div(4);//SYSTEM_CLK_DIV4();
    set_max_vol(MAX_ANOLOG_VOL,MAX_DIGITAL_VOL);///设置最大音量
    dac_out_select(DAC_AMUX1, 0);
    encode_channel = REC_FM; 
#if ECHO_ENABLE
    encode_channel = REC_MIC ;
#endif 
    encode_vol = REC_AMUX_GAIN;
    fm_rev();
    main_vol_set(0, CHANGE_VOL_NO_MEM);
    amp_mute(1);
    alm_on_flag =0;

    fm_rev_powerdown();
    //P05_source_select(P05_SEL_IO);
    break_encode();

}
コード例 #3
0
void main(void)
{

    amp_mute(1);
    clock_in = T0CNT;									//输入时钟,define in clock.h

    sys_init();
    power_key_hdlr(SYS_PWR_ON);
    AMUX_P2IE_SET(AMUX0_IE&AMUX1_IE);
    sys_info_init();
    clear_all_event();
    flush_all_msg();
	
    enter_fm_rev();

    PT2313_Init();
	
    work_mode=RTC_MODE;
#ifdef IR_DEBUG
	IR_Debug_func();
#endif

    while (1)
    {
        switch (work_mode)
        {
        case MUSIC_MODE:
            music_decode();
            break;
#if USB_DEVICE_ENABLE
        case USB_DEVICE_MODE:
            usb_audio_massstorage();
            break;
#endif     

#if 1//FM_MODULE                     
        case FM_RADIO_MODE:
            fm_radio();
            break;
#endif

        case AUX_MODE:
            aux_fun();
            break;

#if 1//RTC_ENABLE
        case RTC_MODE:
            rtc_fun();
            break;        
#endif
        case REC_MIC_MODE:
            rec_mic_fun();
            break;			
        case IDLE_MODE:
	     //power_key_hdlr(SYS_PWR_OFF);
            break;			

	     default:
            	work_mode = MUSIC_MODE;
            break;
        }
        write_info(MEM_SYSMODE ,work_mode);
    }
    //*/
}
コード例 #4
0
ファイル: main.c プロジェクト: go2net/my-com-rec
void main(void)
{

    amp_mute(1);
    clock_in = T0CNT;									//输入时钟,define in clock.h
  //  WDT_EN();
    sys_init();
    //power_key_hdlr(SYS_PWR_ON);
    flashled(LED_ON);

    AMUX_P2IE_SET(AMUX0_IE&AMUX1_IE);
    sys_info_init();
    clear_all_event();
    flush_all_msg();
    //work_mode=REC_MIC_MODE;
    ///*
    while (1)
    {
        switch (work_mode)
        {
        case MUSIC_MODE:
            music_decode();
            break;
#if USB_DEVICE_ENABLE
        case USB_DEVICE_MODE:
            usb_audio_massstorage();
            break;
#endif     

#if FM_MODULE                     
        case FM_RADIO_MODE:
            fm_radio();
            break;
#endif

#ifndef NOT_USE_LINE_IN_FUNC
        case AUX_MODE:
            aux_fun();
            break;
#endif


#if RTC_ENABLE
        case RTC_MODE:
            rtc_fun();
            break;        
#endif
        case REC_MIC_MODE:
            rec_mic_fun();
            break;			
		
        case IDLE_MODE:
#ifndef NO_IDLE_MODE_FUNC				
            idle_mode();			
#endif
	    // power_key_hdlr(SYS_PWR_OFF);
            break;			

	     default:
            	work_mode = MUSIC_MODE;
            break;
        }
        write_info(MEM_SYSMODE ,work_mode);
    }
    //*/
}
コード例 #5
0
/*----------------------------------------------------------------------------*/
void fm_rev( void )
{
    u8 key;
	
    sys_mute_flag =0;

    PT2313_Config(sys_main_vol,VOL_ADJ);

    amp_mute(0);

    while (1)
    {
#if ECHO_ENABLE
        dac_out_select(DAC_AMUX1 | ADD_DEC, 0);  
#else
        dac_out_select(DAC_AMUX1, 0);  
#endif
        key = app_get_msg();

        switch (key)
        {
        case MSG_CHANGE_WORK_MODE:
            return;

        case MSG_MUSIC_NEW_DEVICE_IN:							//有新设备接入
            work_mode = MUSIC_MODE;
            return;
      	 case MSG_FM_SCAN_STOP:
		if(key_ir_detect){
			key_ir_detect =0;
			ir_remote_set_snooze();
		}
		break;
        case MSG_FM_SCAN_ALL:								//play 长按自动全频搜索

            key = fm_scan(0);
            if (key == 3)
            {
                put_msg_lifo(MSG_ALM_ON);
                break;
            }
            if (key == 2)
                return;
            put_msg_lifo(MSG_FM_NEXT_STATION);
            break;

        case  MSG_FM_SCAN_ALL_DOWN :
            key = fm_scan(1);
            if (key == 3)
            {
                put_msg_lifo(MSG_ALM_ON);
                break;
            }
            if (key == 2)
                return;
            break;

        case  MSG_FM_SCAN_ALL_UP:
            key =fm_scan(2);
            if (key == 3)
            {
                put_msg_lifo(MSG_ALM_ON);
                break;
            }
            if (key == 2)
                return;
            break;
#if 0
        case MSG_MUSIC_PP:									//play 短按静音
            put_msg_lifo(MSG_MUTE);
            break;

        case MSG_MUTE:
            break;
#endif
        case MSG_MUSIC_FR:									//搜索上一个台
            flush_all_msg();
            break;

        case MSG_MUSIC_FF:									//搜索下一个台
            flush_all_msg();
            break;

        case MSG_FM_PREV_STEP:
            set_fre(FM_FRE_DEC);
            fre_channel = get_channel_via_fre(frequency - MIN_FRE);						//查找该频点是否有记忆过
            disp_port(MENU_FM_MAIN);
            write_info(MEM_FRE, frequency-MIN_FRE);
            write_info(MEM_CHAN, fre_channel);
            break;

        case MSG_FM_NEXT_STEP:
            set_fre(FM_FRE_INC);
            fre_channel = get_channel_via_fre(frequency - MIN_FRE);						//查找该频点是否有记忆过
            disp_port(MENU_FM_MAIN);
            write_info(MEM_FRE, frequency-MIN_FRE);
            write_info(MEM_CHAN, fre_channel);
            break;

        case MSG_FM_PREV_STATION:
            if (total_channel == 0)
                break;
            fre_channel -= 2;
        case MSG_FM_NEXT_STATION:
            if (total_channel == 0)
                break;
            fre_channel++;

            if ((fre_channel == 0) || (fre_channel == 0xff))
            {
                fre_channel = total_channel;
            }
            else if (fre_channel > total_channel)
            {
                fre_channel = 1;
            }
            frequency = get_fre_via_channle(fre_channel) + MIN_FRE;				//根据台号找频点
            main_vol_set(0, CHANGE_VOL_NO_MEM);
            set_fre(FM_CUR_FRE);
            main_vol_set(0, SET_USE_CURRENT_VOL);
            disp_port(MENU_FM_CHANNEL);
            write_info(MEM_FRE, frequency-MIN_FRE);
            write_info(MEM_CHAN, fre_channel);
            break;

        case MSG_CH_SET:
            if (cur_menu == MENU_INPUT_NUMBER)			//数字输入模式
            {
                if (input_number <= MAX_CHANNL)							//输入的是台号
                {
                    key = get_fre_via_channle(input_number);
                    if (key != 0xff)
                    {
                        frequency = key + MIN_FRE;
                        fre_channel = input_number;
                        main_vol_set(0, CHANGE_VOL_NO_MEM);
                        set_fre(FM_CUR_FRE);
                        main_vol_set(0, SET_USE_CURRENT_VOL);
                        disp_port(MENU_FM_CHANNEL);
                        //break;
                    }

                }
                else if ((input_number >= MIN_FRE) && (input_number <= MAX_FRE)) //输入的是频点
                {
                    frequency = input_number;
                    fre_channel = get_channel_via_fre(frequency - MIN_FRE);
                    main_vol_set(0, CHANGE_VOL_NO_MEM);
                    set_fre(FM_CUR_FRE);
                    main_vol_set(0, SET_USE_CURRENT_VOL);
                }
            }
            write_info(MEM_FRE, frequency-MIN_FRE);
            write_info(MEM_CHAN, fre_channel);
            disp_port(main_menu);

            break;

        case MSG_CH_SAVE:
            ch_save();
            break;


        case MSG_HALF_SECOND:

		alarm_setting_vol_hdlr();

		//bmt_hdlr();			 
	     timer_pwr_off_hdlr();
		
            set_brightness_fade_out();
            if (main_menu_conter < SUB_MENU_TIME)
            {
                main_menu_conter++;
            }
            else if (cur_menu != main_menu)
            {
                put_msg_lifo(MSG_CH_SET);				//跳转至CH_SET消息处理
            }

	     if(cur_menu == main_menu)
	     {
		   disp_port(main_menu);
	     }
            break;


#if 0//RTC_ENABLE
        case MSG_ALM_ON:
            write_next_alm_sec();
            work_mode = RTC_MODE;
            put_msg_lifo(MSG_CHANGE_WORK_MODE);
            break;
#endif

#if KALAOK_FUNCTION
		case MSG_KALAOK:
			work_mode = REC_MIC_MODE;
			return ;
#endif

        default :
            ap_handle_hotkey(key);
            break;
        }
    }
}
コード例 #6
0
/*----------------------------------------------------------------------------*/
u8 fm_scan(u8 mode)
{
    u8 i;
    u8 key;
    u8 result = 0;
    vol_change_en=0;
    input_number_en = 0;
    amp_mute(1);

    if (mode == 0)
    {
        write_info(MEM_CHAN,0);
        write_info(MEM_FRE,0);
        clear_all_fm_point();
        total_channel = 0;
        fre_channel = 0;
        frequency = MIN_FRE - 1;					//自动搜索从最低的频点开始
    }
    fm_set_ch(4);


    for (i = 0;i <= (MAX_FRE-MIN_FRE);i++)
    {

        while (1)
        {
            key = app_get_msg();
            if (key == NO_MSG)
                break;

            switch (key)
            {
            case MSG_MUSIC_NEW_DEVICE_IN:							//有新设备接入
                work_mode = MUSIC_MODE;
                result = 2;
                goto _fm_scan_ret;
            case MSG_AUX_IN :
                work_mode = AUX_MODE;
                result = 2;
                goto _fm_scan_ret;
#if USB_DEVICE_ENABLE
            case MSG_USB_PC_IN:
                work_mode = USB_DEVICE_MODE;
                result = 2;
                goto _fm_scan_ret;
#endif

            case MSG_FM_NEXT_STATION:
            case MSG_FM_SCAN_STOP:
            case MSG_FM_SCAN_ALL:
                result = 0;
                goto _fm_scan_ret;
            case MSG_ALM_ON:
                result = 3;
                goto _fm_scan_ret;


            default:
                ap_handle_hotkey(key);
                break;
            }
        }

        if (mode ==1)
        {
            frequency--;
        }
        else
        {
            frequency++;
        }
        fm_module_mute(1);
        disp_port(MENU_FM_DISP_FRE);
        if (set_fre(FM_CUR_FRE))							//找到一个台
        {
            fm_module_mute(0);
            if (mode == 0)								//搜索所有电台
            {

                save_fm_point(frequency - MIN_FRE);
                fre_channel = get_channel_via_fre(frequency - MIN_FRE);
                total_channel = get_total_mem_channel();
                disp_port(MENU_FM_FIND_STATION);
                delay_10ms(100);
            }
            else
            {
                save_fm_point(frequency - MIN_FRE);
                fre_channel = get_channel_via_fre(frequency - MIN_FRE);
                total_channel = get_total_mem_channel();

                disp_port(MENU_FM_DISP_FRE);
                result = 1;
                goto _fm_scan_ret;
            }
        }

    }
_fm_scan_ret:
    fm_module_mute(0);
    input_number_en = 1;
    vol_change_en = 1;

    amp_mute(0);
	
    return result;
}
コード例 #7
0
void ap_handle_hotkey(u8 key)
{
    u8 res;

    switch (key)
    {

#if ECHO_ENABLE
    case MSG_REV_SW:
        echo_sw();		
        break;
    
	case MSG_REV_STRONG_UP:
	case MSG_REV_STRONG_DOWN:
        if(echo_strong(key))
        {
            disp_port(MENU_REV_STRONG);   
        }
        break;
	
     case MSG_REV_DEEP_UP:
     case MSG_REV_DEEP_DOWN:
        if(echo_deep(key))
        {
            disp_port(MENU_REV_DEEP);
        }
        break;
#endif

     case MSG_ALM_SETUP:
	 	//clr_alarm_func();
	 	break;
     case MSG_SNOOZE_SETUP:
	 	set_snooze_func();
	 	break;
     case MSG_MUTE_UNMUTE:
	 	sys_mute_flag =~sys_mute_flag;
		if(sys_mute_flag){
    			amp_mute(1);
			PT2313_Config(0,VOL_ADJ);
		}
		else{
			PT2313_Config(sys_main_vol,VOL_ADJ);
    			amp_mute(0);
		}
	 	break;
     case MSG_SLEEP_SETUP:
	 	if(work_mode != RTC_MODE){
			timer_pwr_setting();
		}
		break;
     case MSG_SYS_POWERON:
	 	
	 	if(work_mode==RTC_MODE){
			
	 		work_mode= MUSIC_MODE;
		}
		else{
	 		work_mode= RTC_MODE;
		}

		timer_pwr_idx=0;
		
	       put_msg_lifo(MSG_CHANGE_WORK_MODE);
	 	break;

		
    case MSG_USB_DISK_OUT:
    case MSG_SDMMC_OUT:
		
        set_brightness_all_on();
        if( (!device_check() ) && (encode_status >= RECODE_INIT )) //在录音时,活动设备拔出
        {	
            rec_device_out = 1;
            api_stop_encode();
            if(AUX_MODE == work_mode)
	        {
	            main_menu = MENU_AUX;
				disp_port(MENU_AUX);
	        }
#if FM_MODULE 
			else if(FM_RADIO_MODE == work_mode)
	        {
	            main_menu = MENU_FM_MAIN;
                disp_port(MENU_FM_MAIN);
	        }
#endif
            else
            {
                 put_msg_lifo(MSG_MUSIC_NEW_DEVICE_IN);
                 //break;  
            }
		}
        /*
        if((!device_check()) && (REC_MIC_MODE == work_mode))
        {
             put_msg_lifo(MSG_MUSIC_NEW_DEVICE_IN);
             break;   
        }
        */
	    if(MUSIC_MODE != work_mode)
			break;
        put_msg_lifo(MSG_DEVICE_REMOVED);
        disk_remove_deal_for_music();
        break;

#if USB_DEVICE_ENABLE
    case MSG_USB_PC_IN:

    #if ECHO_ENABLE
        if(BUSY == echo_ptr->status)
        {
            close_echo();
        }
    #endif
        break_encode();
        set_brightness_all_on();
        device_check();
        work_mode = USB_DEVICE_MODE;
        put_msg_lifo(MSG_CHANGE_WORK_MODE);
        break;

    case MSG_USB_PC_OUT:
        set_brightness_all_on();
        break;
#endif

    case MSG_AUX_IN :
        break_encode();
        set_brightness_all_on();
#if USB_DEVICE_ENABLE
        if ((AUX_MODE != work_mode) && (work_mode != USB_DEVICE_MODE))
#else
        if (AUX_MODE != work_mode)
#endif
        {
            work_mode = AUX_MODE;
            put_msg_lifo(MSG_CHANGE_WORK_MODE);
        }
        break;

    case MSG_AUX_OUT :
        set_brightness_all_on();

	 if(work_mode != AUX_MODE)break;
	 
        if((RECODE_WORKING == encode_status)||(RECODE_PAUSE == encode_status))
        {	
            break;
        } 

        break_encode();

	 given_device = DEVICE_UDISK;
        given_file_method = PLAY_BREAK_POINT;      
	 put_msg_lifo(MSG_MUSIC_NEW_DEVICE_IN);
		
        break;

    case MSG_SDMMC_IN :
        set_brightness_all_on();
	 device_check();
        if((RECODE_WORKING == encode_status)||(RECODE_PAUSE == encode_status))
        {	
            break;
        } 
        
        break_encode();

#if USB_DEVICE_ENABLE
        if (work_mode == USB_DEVICE_MODE)
            break;
#endif

		given_device = read_info(MEM_ACTIVE_DEV);

		if(given_device == DEVICE_SDMMC0_REC)
			given_device = DEVICE_SDMMC0_REC;
		else
			given_device = DEVICE_SDMMC0;

        given_file_method = PLAY_BREAK_POINT;
        put_msg_lifo(MSG_MUSIC_NEW_DEVICE_IN);
        break;

    case MSG_USB_DISK_IN  :
        set_brightness_all_on();
		device_check();
        if((RECODE_WORKING == encode_status)||(RECODE_PAUSE == encode_status))
        {
            break;
        }
        break_encode();
       
		given_device = read_info(MEM_ACTIVE_DEV);

		if(given_device == DEVICE_UDISK_REC)
			given_device = DEVICE_UDISK_REC;
		else
	    	given_device = DEVICE_UDISK;

        given_file_method = PLAY_BREAK_POINT;      
        put_msg_lifo(MSG_MUSIC_NEW_DEVICE_IN);
        break;

    case MSG_NEXT_WORKMODE:
        break_encode();


	 if(work_mode == MUSIC_MODE){

		device_check();		
	    	if(((device_active &(~VIRTUAL_DEVICE))== DEVICE_UDISK)&&(device_online&DEVICE_SDMMC0)>0){

		    	given_device = DEVICE_SDMMC0;
		       given_file_method = PLAY_BREAK_POINT;      
		        put_msg_lifo(MSG_MUSIC_NEW_DEVICE_IN);
			break;
		}
	 }
	
        work_mode++;
		

	if(work_mode > MAX_WORK_MODE){
		
            work_mode = MUSIC_MODE;

		if(get_device_online_status()&DEVICE_UDISK){
			
	    		given_device = DEVICE_UDISK;
		        given_file_method = PLAY_BREAK_POINT;      
		        put_msg_lifo(MSG_MUSIC_NEW_DEVICE_IN);
		}
		else if(get_device_online_status()&DEVICE_SDMMC0){
			
	    		given_device = DEVICE_SDMMC0;
		        given_file_method = PLAY_BREAK_POINT;      
		        put_msg_lifo(MSG_MUSIC_NEW_DEVICE_IN);
		}
		else{
        		work_mode++;
		}
	}


        put_msg_lifo(MSG_CHANGE_WORK_MODE);
        break;

    case MSG_VOL_UP:
        if (vol_change_en==0)
            break;

	sys_main_vol++;
	sys_main_vol++;
    case MSG_VOL_DOWN:
        if (vol_change_en==0)
            break;
		
	if(sys_main_vol>0)
		sys_main_vol--;

	if(sys_main_vol>MAX_MAIN_VOL){
		sys_main_vol =MAX_MAIN_VOL;
	}
	
	sys_mute_flag =0;
	
	PT2313_Config(sys_main_vol,VOL_ADJ);
	
	 if(sys_main_vol==0){
    		amp_mute(1);
	 }
	 else{
    		amp_mute(0);
	 }		
        dac_mute_control(0,1);					//调节音量时,自动UNMUTE
        write_info(MEM_VOL, sys_main_vol);
        disp_port(MENU_MAIN_VOL);
        break;
		
     case MSG_MUSIC_NEXT_EQ:
	 if(work_mode == RTC_MODE)
	 	break;

            eq_mode++;
            if (eq_mode > CLASSIC)
            {
                eq_mode = NORMAL;
            }

	    PT2313_Config(eq_mode,EQ_ADJ);
			
            set_eq(NORMAL);
            disp_port(MENU_SET_EQ);
            break;
			
    case MSG_100:
		
        if (!input_number_en)
            break;

	if (input_number > 999)
            input_number = 0;

	      key_100_flag = 0xFF;
#ifdef USE_10_PLUS_FUNC				  
	     input_number = input_number+10;
#else
	     input_number = input_number+100;
#endif
        disp_port(MENU_INPUT_NUMBER);
	break;		
	
    case MSG_0:
    case MSG_1:
    case MSG_2:
    case MSG_3:
    case MSG_4:
    case MSG_5:
    case MSG_6:
    case MSG_7:
    case MSG_8:
    case MSG_9:
		
        if (!input_number_en)
            break;		
		
	     if(key_100_flag ==0xFF){
			input_number += key;
			key_100_flag = 0xFE;
	     }
	     else if(key_100_flag ==0xFE){
		 	
			input_number += (input_number%10)*10-(input_number%10)+key;
			key_100_flag = 0x00;
	     }
	     else 
	     {
	     	     	if((input_number)>6553){
				input_number = 0x0000;			
			}
        		input_number = input_number * 10 + key;
			key_100_flag = 0x00;			
	     }
#if 1
	     if (input_number > 9999)
	     {
		       input_number = 0;			
			input_number = input_number *10 + key;
	    }
#endif
        disp_port(MENU_INPUT_NUMBER);
        break;
////////////////录音
    case MSG_REC_KEY_AT_USB:

       if(RTC_MODE == work_mode){
		break;
	}
	   
	if(RECODE_PLAY >= encode_status)
       {		
		rec_device_sel=DEVICE_UDISK;
		api_stop_encode();			
            	put_msg_lifo(MSG_REC_FIND);
	}
        else
        {
            put_msg_lifo(MSG_REC_STOP);
        }		
	break;
	
    case MSG_REC_KEY_AT_SD:

	if(RTC_MODE == work_mode){
		break;
	}
	if(RECODE_PLAY >= encode_status)
       {		
		rec_device_sel=DEVICE_SDMMC0;
       	api_stop_encode();			
            	put_msg_lifo(MSG_REC_FIND);
	}
        else
        {
            put_msg_lifo(MSG_REC_STOP);
        }	
	break;
#if 0	
    case MSG_REC_KEY:	  //录音开始和结束
	if(RECODE_PLAY >= encode_status)
        {
            put_msg_lifo(MSG_REC_FIND);

        }
        else
        {
            put_msg_lifo(MSG_REC_STOP);
        }
        break;
#endif
	case MSG_REC_PP:      //录音暂停和继续录音

        if(RECODE_WORKING == encode_status)
        {
            put_msg_lifo(MSG_REC_PAUSE);
        }
        else if(RECODE_PAUSE == encode_status)
        {

            put_msg_lifo(MSG_REC_CONTINUE);
        }
        break;

    case MSG_ENCODE_END:   //设备写err  或 设备满
	//	deg_str("MSG_ENCODE_END \n");
		if(rec_device_out)		//录音时活动设备拔出,在设备拔出那里处理,在此不做处理
		{
			rec_device_out =0;
			break;
		}

        api_stop_encode();		//停止录音
		put_msg_lifo(MSG_REC_PLAY);
		break;

	 case MSG_ENCODE_FAT_FULL:  //建文件时
	 //	deg_str("MSG_ENCODE_FAT_FULL \n");
		api_stop_encode();		//停止录音
		if(REC_MIC_MODE == work_mode)		//录音时写设备出现问题、设备满
        {
             put_msg_lifo(MSG_MUSIC_NEW_DEVICE_IN);
             break;   
        }
       // break_encode();
        if(AUX_MODE == work_mode)
        {
            main_menu = MENU_AUX;
        }
#if FM_MODULE 
		else if(FM_RADIO_MODE == work_mode)
        {
            main_menu = MENU_FM_MAIN;
        }
#endif
        disp_port(main_menu);
        break;
////////////////录音涉及的各种状态
    case MSG_REC_FIND:
//        if(RECODE_PLAY >= encode_status)
//        {
//            break;
//        }
#if USB_DEVICE_ENABLE
        if(USB_DEVICE_MODE == work_mode)
        {
            break;
        }
#endif
        encode_status = RECODE_INIT;
 
        if(REC_MIC_MODE != work_mode)
        {
            work_mode = REC_MIC_MODE;
            put_msg_lifo(MSG_CHANGE_WORK_MODE);
            given_device = rec_device_sel;//read_info(MEM_ACTIVE_DEV);
            break;
        }
#if 0		
        else //if((MUSIC_MODE != work_mode))
        {
            if (given_device == NO_DEVICE)
            {
                
                given_device = read_info(MEM_ACTIVE_DEV);

            }
        }      
        if( (( given_device & (~VIRTUAL_DEVICE ))  != DEVICE_SDMMC0) 
            && ((given_device & (~VIRTUAL_DEVICE)) != DEVICE_UDISK)
          )
        {
            given_device = DEVICE_SDMMC0;
        }
#endif	
        given_device = rec_device_sel;//read_info(MEM_ACTIVE_DEV);

        sys_clk_div(2);//SYSTEM_CLK_DIV2();

        put_msg_lifo(MSG_MUSIC_SELECT_NEW_DEVICE);
        break;
    case MSG_REC_START:		//开始录音

	rec_device_out = 0;
#if 0
		 rec_sys_set(0);  //0:24M   1:48M
		 sys_clk_div(2);//SYSTEM_CLK_DIV2();  //24 M
#else
	rec_sys_set(1);
	sys_clk_div(1);//SYSTEM_CLK_DIV1();	  //48 M
#endif
        //init_rec_name();

               
        device_active |= VIRTUAL_DEVICE;
        encode_device = device_active;	 //设置录音存储设备

        write_file_info(0);

        set_rec_channel(encode_channel); //设置录音通道  

        set_rec_vol(encode_vol);		 //设置录音音量

		

	if(REC_MIC_MODE == work_mode)
	{	
			kala_dac_off();
//			dac_mute_control(1,1);
#if KALAOK_FUNCTION
			dsp_set_adc_con(0);
			P3HD &=~(1<<6);
#endif
	}

        if(REC_MIC == encode_channel)
        {
            set_rec_track(TRACK_LEFT);
        }
        else
        {
            set_rec_track(TRACK_ALL);
        }
        /**/
        
        CLKGAT |= MP3CLK;// | SPIURCLK;

		
 //     CLKCON0 |= DACCLK;
 //		P3HD &=~(1<<6);
	   
        if(DEVICE_SDMMC0 == (device_active & (~VIRTUAL_DEVICE)))
        {
            CLKGAT |= USBCLK;
        }
        else if(DEVICE_UDISK == (device_active & (~VIRTUAL_DEVICE)))
        {
            CLKGAT |= SDCLK;
        }
#if ECHO_ENABLE
        if(BUSY == echo_ptr->status)
        {
            close_echo();
        }
#endif
        ///0x
        //my_memset(0x4000,0,0x787f-0x4000);
        //my_memset(0x8000,0,0x9c3f-0x8000);

//混响强度 0x400c 取值范围 0-255
//混响深度 0x4015 0x4014   取值范围 0-2048

#if ECHO_ENABLE      
        if(1 != start_encode_echo(IS_MP3))			 //开始录音
#else
        if(1 != start_encode(IS_MP3))			 //开始录音
#endif
        {
		put_msg_lifo(MSG_ENCODE_FAT_FULL);
		break;
	}
#if ECHO_ENABLE  ///<减弱冲击声,打开混响深度和强度
        delay_10ms(20);
        if( REC_MIC == ( encode_channel & 0xf ) ) ///<MIC 下有混响
        {
            set_echo(app_echo.strong, app_echo.deep);
        }
//        app_echo.strong = REC_ECHO_STRONG;
        echo_vol_set(REC_MIC_VOL);

#endif

        /*
        if(REC_MIC_MODE == work_mode)
        {
    		while(!((cmd_ctl_rec(REC_NO_OPT,0)) &  FRIST_ADC_PACKET)) //采数据前的处理
    		{
    
    		}
            delay_10ms(50);//抛弃半秒的数据
        }
		cmd_ctl_rec(ENABLE_REC_DATA,ENABLE_REC_BIT);
        */
        encode_status = RECODE_WORKING;
#if 0//FM_MODULE 
		if(FM_RADIO_MODE != work_mode)
#endif
		{
		 	main_menu = MENU_RECWORKING;//
		}
		disp_port(main_menu);
        //disp_port(MENU_REC);
        break;
    case MSG_REC_STOP:      //停止录音
        api_stop_encode();		//停止录音
        put_msg_lifo(MSG_REC_PLAY);
        break;
    case MSG_REC_PAUSE:     //暂停录音
		encode_status = RECODE_PAUSE;
	
#if  0//FM_MODULE 
		if(FM_RADIO_MODE == work_mode)
			disp_port(MENU_FM_MAIN);
		else
#endif
		{
			main_menu = MENU_REC_PAUSE;	
		  	disp_port(MENU_REC_PAUSE);
		}
		 		
        pause_encode();
        break;
    case MSG_REC_CONTINUE:  //暂停录音之后继续录音
		encode_status = RECODE_WORKING;
	
#if FM_MODULE 
		if(FM_RADIO_MODE == work_mode)
			disp_port(MENU_FM_MAIN);
		else
#endif
		{
		 	main_menu = MENU_RECWORKING;//
		    disp_port(MENU_RECWORKING);
		}
			
        continue_encode();
        break;
    case MSG_REC_PLAY:     //播放最后的录音文件

        encode_status = RECODE_PLAY;
        given_device = encode_device & (~VIRTUAL_DEVICE);

        if( (given_device != DEVICE_SDMMC0) && (given_device != DEVICE_UDISK))
        {
            given_device = DEVICE_SDMMC0;
        }
        given_device |= VIRTUAL_DEVICE;
        if((MUSIC_MODE != work_mode))
        {
            put_msg_lifo(MSG_MUSIC_NEW_DEVICE_IN);
        }
        else
        {
            put_msg_lifo(MSG_MUSIC_SELECT_NEW_DEVICE);
        }
        break;

    case MSG_MUSIC_SELECT_NEW_DEVICE:					        //重新选择设备

        res = find_device(given_device);

        if ((res == DEV_INIT_ERR) ||
                (res == NO_DEFINE_DEV))                    //指定的设备不在线,或初始化失败
        {
		
            given_device = DEVICE_AUTO_NEXT;			   //自动选择下一个设备
            put_msg_lifo(MSG_MUSIC_SELECT_NEW_DEVICE);
            break;
        }
        else if ((res == NO_EFFECTIVE_DEV) ||
                 (res == NO_DEV_ONLINE))                    //无可播放的设备
        {		
            if(RECODE_STOP != encode_status)
            {
                encode_status = RECODE_STOP;
		  if(REC_MIC_MODE == work_mode)
	         {
					put_msg_lifo(MSG_NEXT_WORKMODE);
		  }
                break;
            }
            else
            {	
                put_msg_lifo(MSG_NEXT_WORKMODE);
            }
            break;
        }
        else
        {		
            if(RECODE_PLAY < encode_status)
            {
                put_msg_lifo(MSG_REC_START);
            }
            else
            {
                if(RECODE_PLAY == encode_status)  //去播刚录好的文件
                {
                    encode_status = RECODE_STOP;
#if VIRTUAL_ENABLE
                    given_file_number = encode_filenum;
#else
                    given_file_number = encode_filenum + encode_fristfile - 1;
#endif
                    put_msg_lifo(MSG_MUSIC_PLAY_NEW_FILE);
                }
                else
                {
                    put_msg_lifo(MSG_MUSIC_SELECT_NEW_FILE);		//找到可用设备
                }
            }
            
        }
        break;



    }
}